ISO/IEC 11801-3:2017
(Main)Information technology — Generic cabling for customer premises — Part 3: Industrial premises
Information technology — Generic cabling for customer premises — Part 3: Industrial premises
ISO/IEC 11801-3:2017(E) This document specifies generic cabling, which is critical for providing robust services to the automation islands in industrial premises, or industrial spaces within other types of building. Additionally those premises can include office spaces (for which generic cabling is specified in ISO/IEC 11801-2) or data centre spaces (for which generic cabling is specified in ISO/IEC 11801-5).
Technologies de l'information — Câblage générique des locaux d'utilisateurs — Partie 3: Titre manque
General Information
Relations
Standards Content (Sample)
ISO/IEC 11801-3
Edition 1.0 2017-11
INTERNATIONAL
STANDARD
Information technology – Generic cabling for customer premises
Part 3: Industrial premises
ISO/IEC 11801-3:2017-11(en)
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2017 ISO/IEC, Geneva, Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about
ISO/IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address
below or your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 20 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - www.iec.ch/searchpub IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 65 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: csc@iec.ch.
---------------------- Page: 2 ----------------------
ISO/IEC 11801-3
Edition 1.0 2017-11
INTERNATIONAL
STANDARD
Information technology – Generic cabling for customer premises
Part 3: Industrial premises
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 35.200 ISBN 978-2-8322-5032-7
Warning! Make sure that you obtained this publication from an authorized distributor.
---------------------- Page: 3 ----------------------
– 2 – ISO/IEC 11801-3:2017 © ISO/IEC 2017
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 10
2 Normative references . 10
3 Terms, definitions, abbreviated terms and symbols . 11
3.1 Terms and definitions . 11
3.2 Abbreviated terms . 12
3.3 Symbols . 12
4 Conformance . 12
5 Structure of the generic cabling system . 13
5.1 General . 13
5.2 Functional elements . 13
5.3 Cabling subsystem . 14
5.3.1 General structure . 14
5.3.2 Campus and building backbone cabling subsystem . 15
5.3.3 Floor cabling subsystem . 15
5.3.4 Intermediate cabling subsystem . 15
5.3.5 Centralized cabling architecture . 16
5.3.6 Design objectives . 16
5.4 Interconnection of subsystems . 16
5.5 Accommodation of functional elements . 18
5.6 Interfaces . 19
5.6.1 Equipment interfaces and test interfaces . 19
5.6.2 Channels and permanent links . 19
5.7 Dimensioning and configuring . 19
5.7.1 General . 19
5.7.2 Distributors . 19
5.7.3 Connecting hardware . 20
5.7.4 Apparatus attachment and equipment cords . 20
5.7.5 Patch cords and jumpers . 20
5.7.6 Telecommunications outlet . 20
5.7.7 Telecommunications rooms and equipment rooms . 21
5.7.8 Industrial enclosures . 21
6 Channel performance requirements . 21
6.1 General . 21
6.2 Environmental performance . 22
6.3 Transmission performance . 22
6.3.1 General . 22
6.3.2 Balanced cabling . 22
6.3.3 Optical fibre cabling . 23
7 Link performance requirements . 23
7.1 General . 23
7.2 Balanced cabling . 23
7.3 Optical fibre cabling . 23
8 Reference implementations . 23
8.1 General . 23
---------------------- Page: 4 ----------------------
ISO/IEC 11801-3:2017 © ISO/IEC 2017 – 3 –
8.2 Balanced cabling . 23
8.2.1 General . 23
8.2.2 Intermediate cabling subsystem . 24
8.2.3 Floor cabling subsystem . 26
8.2.4 Campus and building backbone cabling subsystem . 28
8.3 Optical fibre cabling . 28
9 Cable requirements . 28
9.1 General . 28
9.2 Balanced cables . 28
9.3 Optical fibre cables . 29
10 Connecting hardware requirements . 29
10.1 General requirements . 29
10.2 Connecting hardware for balanced cabling . 29
10.2.1 General requirements . 29
10.2.2 Electrical, mechanical and environmental performance . 29
10.3 Connecting hardware for optical fibre cabling . 30
10.3.1 General requirements . 30
10.3.2 Optical, mechanical and environmental performance . 30
11 Cords . 30
11.1 Jumpers . 30
11.2 Balanced cords . 30
11.2.1 General . 30
11.2.2 Additional requirements for apparatus attachment cords . 30
11.3 Optical fibre cords . 30
Annex A (normative) Industrial cabling system . 31
A.1 General . 31
A.2 Industrial intermediate cabling subsystem . 31
Annex B (normative) Additional reference implementations . 33
B.1 General . 33
B.2 Channel configurations . 33
B.2.1 General . 33
B.2.2 Channels with no connections . 33
B.2.3 Channels with inter-connections . 34
B.2.4 End-to-end link (E2E link) . 35
B.3 Channels using balanced cabling bulkhead connections . 36
Annex C (informative) Other implementations . 38
C.1 General . 38
C.2 Channels using balanced cabling bulkhead connections with additional
connections . 38
Bibliography . 41
Figure 1 – Relationships between the generic cabling documents produced by
ISO/IEC JTC 1/SC 25 . 7
Figure 2 – Relationships between the ISO/IEC and IEC cabling documents that apply
to industrial premises . 8
Figure 3 – Configuration of apparatus-based functional elements within industrial
premises . 14
Figure 4 – Structure of generic cabling for industrial environment . 14
---------------------- Page: 5 ----------------------
– 4 – ISO/IEC 11801-3:2017 © ISO/IEC 2017
Figure 5 – Centralized structure of generic cabling for industrial premises . 16
Figure 6 – Hierarchical structure of generic cabling for industrial premises . 17
Figure 7 – Inter-relationship of functional elements in an installation with diversity for
protection against failure (CPs optional between IDs and TOs) . 17
Figure 8 – Accommodation of functional elements (CPs optional between IDs and
TOs) . 18
Figure 9 – Equipment and test interfaces . 19
Figure 10 – Transmission performance of a channel . 21
Figure 11 – Example of a system showing the location of cabling interfaces and extent
of associated channels . 22
Figure 12 – Intermediate cabling models . 25
Figure 13 – Floor cabling model . 27
Figure A.1 – Industrial cabling system supporting several AIs via an IID . 31
Figure A.2 – Combined structure of generic and industrial cabling system using an IID . 32
Figure B.1 – Channel configurations without intermediate connections . 34
Figure B.2 – Channel configurations with inter-connections . 35
Figure B.3 – Channel configurations with bulkhead connections . 36
Figure C.1 – Channel configurations with bulkhead and additional connections . 39
Table 1 – Maximum channel lengths . 20
Table 2 – Length assumptions used in the mathematical modelling of balanced
intermediate cabling . 25
Table 3 – Intermediate link length equations . 26
Table 4 – Floor link length equations . 28
Table B.1 – Channel length equations for balanced cabling with inter-connections . 35
Table B.2 – Channel length equations with bulkhead connections . 37
Table C.1 – Channel equations with bulkhead and additional connections . 40
---------------------- Page: 6 ----------------------
ISO/IEC 11801-3:2017 © ISO/IEC 2017 – 5 –
INFORMATION TECHNOLOGY –
GENERIC CABLING FOR CUSTOMER PREMISES
Part 3: Industrial premises
FOREWORD
1) ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission)
form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC
participate in the development of International Standards through technical committees established by the
respective organization to deal with particular fields of technical activity. ISO and IEC technical committees
collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in
liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have
established a joint technical committee, ISO/IEC JTC 1.
2) The formal decisions or agreements of IEC and ISO on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested IEC National Committees and ISO member bodies.
3) IEC, ISO and ISO/IEC publications have the form of recommendations for international use and are accepted
by IEC National Committees and ISO member bodies in that sense. While all reasonable efforts are made to
ensure that the technical content of IEC, ISO and ISO/IEC publications is accurate, IEC or ISO cannot be held
responsible for the way in which they are used or for any misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees and ISO member bodies undertake to
apply IEC, ISO and ISO/IEC publications transparently to the maximum extent possible in their national and
regional publications. Any divergence between any ISO, IEC or ISO/IEC publication and the corresponding
national or regional publication should be clearly indicated in the latter.
5) ISO and IEC do not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. ISO or IEC are not responsible
for any services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or ISO or its directors, employees, servants or agents including individual experts
and members of their technical committees and IEC National Committees or ISO member bodies for any
personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for
costs (including legal fees) and expenses arising out of the publication of, use of, or reliance upon, this ISO/IEC
publication or any other IEC, ISO or ISO/IEC publications.
8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this ISO/IEC publication may be the subject of
patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
International Standard ISO/IEC 11801-3 was prepared by subcommittee 25: Interconnection
of information technology equipment, of ISO/IEC joint technical committee 1: Information
technology.
This first edition cancels and replaces ISO/IEC 24702:2006 and Amendment 1:2009. This
edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) standard re-structured to contain only those requirements that are specific for generic
cabling systems installed in industrial premises;
b) support of critical process control, monitoring and automation (PCMA) services between
automation islands by adding new Annex A (normative) “Industrial cabling system”;
c) support of specific requirements for industrial cabling the end-to-end link (E2E) has been
introduced and delivers additional channel configuration covered in Annex B (normative);
d) silica optical fibre cabling has been removed from this International Standard.
---------------------- Page: 7 ----------------------
– 6 – ISO/IEC 11801-3:2017 © ISO/IEC 2017
ISO/IEC 11801-3 is to be read in conjunction with ISO/IEC 11801-1.
This International Standard has been approved by vote of the member bodies, and the voting
results may be obtained from the address given on the second title page.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the ISO/IEC 11801 series, published under the general title Information
technology – Generic cabling for customer premises, can be found on the IEC website.
---------------------- Page: 8 ----------------------
ISO/IEC 11801-3:2017 © ISO/IEC 2017 – 7 –
INTRODUCTION
The importance of cabling infrastructure is similar to that of other fundamental utilities such as
water and energy supply and interruptions to the services provided over that infrastructure
can have a serious impact. A lack of design foresight, the use of inappropriate components,
incorrect installation, poor administration or inadequate support can threaten quality of service
and have commercial consequence for all types of users.
This document specifies generic cabling, which is critical for providing robust services to the
automation islands in industrial premises, or industrial spaces within other types of building.
Additionally those premises can include
• office spaces for which generic cabling is specified in ISO/IEC 11801-2,
• data centre spaces for which generic cabling is specified in ISO/IEC 11801-5.
Generic cabling for distributed building services in industrial spaces is specified in
ISO/IEC 11801-6, which addresses all of the above premises and spaces within them.
This document has taken into account the correlation between all parts of the ISO/IEC 11801
series and the IEC 61918 and IEC 61784-5 series.
Figure 1 shows the schematic and contextual relationships between the standards relating to
information technology cabling produced by ISO/IEC JTC 1/SC 25, namely the ISO/IEC 11801
series of standards for generic cabling design, standards for the installation, operation and
administration of generic cabling and for testing of installed generic cabling.
PREMISES-SPECIFIC
CABLING TESTING
CABLING DESIGN
STANDARDS
STANDARDS
CABLING INSTALLATION,
OPERATION
and
ADMINISTRATION
STANDARDS
ISO/IEC 11801-1 Examples
ISO/IEC 11801-2
Information Technology: Example
ISO/IEC 11801-3
Generic Cabling:
ISO/IEC 14763-3
General Requirements
ISO/IEC 11801-4
ISO/IEC 11801-5
Examples
ISO/IEC 11801-6
ISO/IEC 14763-2
ISO/IEC 18598
ISO/IEC 30129
CABLING DESIGN
TECHNICAL
REPORTS
Examples
ISO/IEC TR 11801-9901
ISO/IEC TR 11801-9902
ISO/IEC TR 11801-9903
ISO/IEC TR 11801-9904
ISO/IEC TR 11801-9905
ISO/IEC TR 24704
ISO/IEC TR 24750
ISO/IEC TR 29125 IEC
Figure 1 – Relationships between the generic cabling
documents produced by ISO/IEC JTC 1/SC 25
---------------------- Page: 9 ----------------------
– 8 – ISO/IEC 11801-3:2017 © ISO/IEC 2017
The generic cabling specified by this document provides users with
a) an application independent system capable of supporting a wide range of applications in a
range of installation and operating environments,
b) a flexible scheme such that modifications are both easy and economical,
c) a multi-vendor supply chain within an open market for cabling components.
In addition, this document provides
d) relevant industry professionals with guidance allowing the accommodation of cabling
before specific requirements are known, i.e. in the initial planning either for construction or
refurbishment and for further deployment as the requirements of areas are defined,
e) industry and standardization bodies with a cabling system which supports current products
and provides a basis for future product development and applications standardization.
Applications addressed in this document include those developed by the technical committees
of IEC (including the subcommittees of ISO/IEC JTC 1), including critical industrial process
control and monitoring applications and study groups of ITU-T.
As a result, this document
1) specifies a structure for generic cabling supporting a wide variety of applications,
2) adopts balanced cabling channel and link Classes D, E, E , F and F , specified in
A A
ISO/IEC 11801-1,
3) adopts component requirements, specified in ISO/IEC 11801-1, and specifies cabling
implementations that ensure performance of permanent links and of channels that meet or
exceed the requirements of a specified group (e.g. Class) of applications.
Figure 2 shows the relationship between all the documents (the generic cabling standards
produced by ISO/IEC JTC 1/SC 25 and the application-specific standards produced by
IEC SC 65C) that apply to industrial premises.
IEC
Figure 2 – Relationships between the ISO/IEC and IEC
cabling documents that apply to industrial premises
---------------------- Page: 10 ----------------------
ISO/IEC 11801-3:2017 © ISO/IEC 2017 – 9 –
It is anticipated that the generic cabling system meeting the minimum requirements of this
document will have a life expectancy consistent with other infrastructures within industrial
premises.
This document has taken into account requirements specified in application standards listed
in ISO/IEC 11801-1:2017, Annex E. It refers to International Standards for components and
test methods whenever appropriate International Standards are available.
---------------------- Page: 11 ----------------------
– 10 – ISO/IEC 11801-3:2017 © ISO/IEC 2017
INFORMATION TECHNOLOGY –
GENERIC CABLING FOR CUSTOMER PREMISES
Part 3: Industrial premises
1 Scope
This part of ISO/IEC 11801 specifies generic cabling for use within industrial premises, or
industrial areas within other types of premises, which can comprise single or multiple
buildings on a campus. It covers balanced cabling and optical fibre cabling.
This document is optimized for premises in which the maximum distance over which
telecommunications services can be distributed is 10 000 m. The principles of this document
can be applied to larger installations.
Cabling defined by this document supports a wide range of services, including automation,
process control, and monitoring applications. That can also incorporate the supply of power.
This document specifies directly or via reference to ISO/IEC 11801-1
a) the structure and minimum configuration for generic cabling within industrial premises,
b) the interfaces at the telecommunications outlet (TO),
c) the performance requirements for cabling links and channels,
d) the implementation requirements and options,
e) the performance requirements for cabling components,
f) the conformance requirements and verification procedures.
The cabling providing critical automation, process control and monitoring applications within
the automation islands is not addressed by this document. Information for this application-
specific cabling is provided in the IEC 61784-5 series (design) and in IEC 61918 (installation).
Safety (electrical safety and protection, fire, etc.) and electromagnetic compatibility (EMC)
requirements are outside the scope of this document, and are covered by other standards and
by regulations. However, information given by this document can be of assistance.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 61918, Industrial communication networks – Installation of communication networks in
industrial premises
IEC 61754-20, Fibre optic interconnecting devices and passive components – Fibre optic
connector int
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.