ISO 13583-1:2023

Centrifugally cast steel and alloy products — Part 1: General testing and tolerances

This document specifies the requirements for horizontal and vertical centrifugally cast steel and alloy products to be used in the following applications: a) heat resisting; b) corrosion resisting; c) general engineering.

Produits en acier et alliages moulés par centrifugation — Partie 1: Conditions générales d'essais et tolérances

General Information

• Status: Published
• Publication Date: 02-Feb-2023
• ICS: 77.140.80 - Iron and steel castings
• Technical Committee: ISO/TC 17/SC 11 - Steel castings
• Drafting Committee: ISO/TC 17/SC 11 - Steel castings
• Current Stage: 6060 - International Standard published
• Start Date: 03-Feb-2023
• Due Date: 12-Jul-2023
• Completion Date: 03-Feb-2023

Relations

• Revises: ISO 13583-1:2015 - Centrifugally cast steel and alloy products — Part 1: General testing and tolerances
• Effective Date: 06-Jun-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13583-1
Third edition
2023-02
Centrifugally cast steel and alloy
products —
Part 1:
General testing and tolerances
Produits en acier et alliages moulés par centrifugation —
Partie 1: Conditions générales d'essais et tolérances
Reference number
ISO 13583-1:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 13583-1:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 13583-1:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials . 3
5 Supply . 3
6 Mechanical tests .3
7 Surface finish requirements.3
8 Minimum sound wall (MSW) thickness and soundness . 4
9 Dimensional and shape tolerances. 4
9.1 General . 4
9.2 Length . 4
9.3 Straightness . 4
9.4 Outside and inside diameters . 5
10 Inspection procedures and standards of acceptance . 6
11 Production welding . 6
12 Supplementary requirements . 6
12.1 General . 6
12.2 Pressure test . . 6
12.3 Elevated temperature test . 6
12.4 Acid etch ring test . 6
12.5 Magnetic particle test . 7
12.6 Ferrite determination . 7
12.7 Corrosion testing . 7
12.8 Eddy current testing . . 7
12.9 Radiography . 7
12.10 Ultrasonic testing . 7
iii
© ISO 2023 – All rights reserved

---------------------- Page: 3 ----------------------
ISO 13583-1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 11,
Steel castings.
This third edition cancels and replaces the second edition (ISO 13583-1:2015), of which it constitutes a
minor revision. The changes are as follows:
— updated titles to normative references;
— editorial update.
A list of all parts in the ISO 13583 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2023 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 13583-1:2023(E)
Centrifugally cast steel and alloy products —
Part 1:
General testing and tolerances
1 Scope
This document specifies the requirements for horizontal and vertical centrifugally cast steel and alloy
products to be used in the following applications:
a) heat resisting;
b) corrosion resisting;
c) general engineering.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3651-1, Determination of resistance to intergra
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 13583-1
ISO/TC 17/SC 11
Centrifugally cast steel and alloy
Secretariat: ANSI
products —
Voting begins on:
2022-11-17
Part 1:
Voting terminates on:
General testing and tolerances
2023-01-12
Produits en acier et alliages moulés par centrifugation —
Partie 1: Conditions générales d'essais et tolérances
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 13583-1:2022(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2022

---------------------- Page: 1 ----------------------
ISO/FDIS 13583-1:2022(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 13583-1
ISO/TC 17/SC 11
Centrifugally cast steel and alloy
Secretariat: ANSI
products —
Voting begins on:
Part 1:
Voting terminates on:
General testing and tolerances
Produits en acier et alliages moulés par centrifugation —
Partie 1: Conditions générales d'essais et tolérances
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: [phone]
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [e-mail]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 13583-1:2022(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2022 – All rights reserved
NATIONAL REGULATIONS. © ISO 2022

---------------------- Page: 2 ----------------------
ISO/FDIS 13583-1:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials . 3
5 Supply . 3
6 Mechanical tests .3
7 Surface finish requirements.3
8 Minimum sound wall (MSW) thickness and soundness . 4
9 Dimensional and shape tolerances. 4
9.1 General . 4
9.2 Length . 4
9.3 Straightness . 4
9.4 Outside and inside diameters . 5
10 Inspection procedures and standards of acceptance . 6
11 Production welding . 6
12 Supplementary requirements . 6
12.1 General . 6
12.2 Pressure test . . 6
12.3 Elevated temperature test . 6
12.4 Acid etch ring test . 6
12.5 Magnetic particle test . 7
12.6 Ferrite determination . 7
12.7 Corrosion testing . 7
12.8 Eddy current testing . . 7
12.9 Radiography . 7
12.10 Ultrasonic testing . 7
iii
© ISO 2022 – All rights reserved

---------------------- Page: 3 ----------------------
ISO/FDIS 13583-1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 11,
Steel castings.
This third edition cancels and replaces the second edition (ISO 13583-1:2015), of which it constitutes a
minor revision. The changes are as follows:
— updated titles to normative references;
— editorial update.
A list of all parts in the ISO 13583 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2022 – All rights reserved

---------------------- Page: 4 ----------------------
FINAL DRAFT INTERNATIONAL STANDA
...

Third
ISO FDIS 13583-1
edition :2022-10-
07(E)











2022-11-03
Centrifugally cast steel and alloy products —
Part 1:
General testing and tolerances
Produits en acier et alliages moulés par centrifugation — Partie 1:
Conditions générales d’essais et tolérances

---------------------- Page: 1 ----------------------
Reference number
ISO/FDIS 13583-1


© ISO 2015
ISO/FDIS 13583-1

---------------------- Page: 2 ----------------------
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015

---------------------- Page: 3 ----------------------
© ISO 2022, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise
in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an
intranet, without prior written permission. Permission can be requested from either ISO at the address below or
ISO’s member body in the country of the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org

---------------------- Page: 4 ----------------------
ii © ISO 2015 – All rights reserved

---------------------- Page: 5 ----------------------
ISO/FDIS 13583-1


Contents Page
Foreword . iv
1 Scope .1
2 Normative references .1
3 Terms and definitions . 1
4 Materials .3
5 Supply .3
6 Mechanical tests .3
7 Surface finish requirements . 4
8 Minimum sound wall (MSW) thickness and soundness .4
9 Dimensional and shape tolerances .4
9.1 General .4
9.2 Length .4
9.3 Straightness .4
9.4 Outside and inside diameters . 5
10 Inspection procedures and standards of acceptance .6
11 Production welding .6
12 Supplementary requirements . 6
12.1 General .6
12.2 Pressure test .7
12.3 Elevated temperature test . 7
12.4 Acid etch ring test .7
12.5 Magnetic particle test . 7
12.6 Ferrite determination . 7
12.7 Corrosion testing .7
12.8 Eddy current testing . 7
12.9 Radiography . 7
12.10 Ultrasonic testing .7

---------------------- Page: 6 ----------------------
© ISO 2015 – All rights reserved iii

---------------------- Page: 7 ----------------------
ISO/FDIS 13583-1:2022(E)
ISO/FDIS 13583-1


viii © ISO 2022– All rights reserved

---------------------- Page: 8 ----------------------
ISO/FDIS 13583-1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
constitute an endorsement.
For an explanation onof the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’sISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT)), see
www.iso.org/iso/foreword.htmlthe following URL: .
This document was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC11SC 11, Steel
Castings castings.
This third edition cancels and replaces the firstsecond edition (ISO 13583-1:2015), of which has been
editorially revised with the followingit constitutes a minor revision. The changes are as follows:
— updated titles to normative references;
— Conform to the most recent versioneditorial update.
A list of all parts in the ISO/IEC Directives, Part 2;
— Wording consistency to align with other ISO documents.
editorially revised to confISO 13583 consistsseries can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.htmlthe following parts, under the
general title .
© ISO 2022 – All rights reserved ix

---------------------- Page: 9 ----------------------
ISO/FDIS 13583-1:2022(E)
Centrifugally cast steel and alloy products:
— Part 1: General testing and tolerances
— Part 2: Materials











iv © ISO 2015 – All rights reserved
x © ISO 2022– All rights reserved

---------------------- Page: 10 ----------------------
INTERNATIONAL STANDARD ISO/FDIS 13583-1




Centrifugally cast steel and alloy products —
Part 1:
General testing and tolerances

241 Scope
This document specifies the requirements for horizontal and vertical centrifugally cast steel and alloy products to
be used in the following applications:
a) heat resisting;
b) corrosion resisting;
c) general engineering.
252 Normative references
The following documents are referred to in the testtext in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references, the
latest edition of the referenced document (including any amendments) applies.
ISO 3651--1, Determination of resistance to intergranular corrosion of stainless steels — Part 1: Austenitic and
ferritic-austenitic (duplex) stainless steels — Corrosion test in nitric acid medium by measurement of loss in mass
(Huey test)
ISO 3651--2, Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic, austenitic
and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid
ISO 4986, Steel and iron castings — Magnetic particle testing
ISO 4987, Steel and iron castings — Liquid penetrant testing
ISO 4990, Steel castings — General technical delivery requirements
ISO 4992--1, Steel castings — Ultrasonic etesting— Part 1: Steel castings for general purposes
ISO 4992--2, Steel castings — Ultrasonic testing— Part 2: Steel castings for highly stressed components
ISO 4993, Steel castings — Radiographic testing
ISO 6892--1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
© ISO 2022 – All rights reserved xi

---
...