ISO/PRF 3011

Rubber- or plastics-coated fabrics -- Determination of resistance to ozone cracking under static conditions

Supports textiles revêtus de caoutchouc ou de plastique -- Détermination de la résistance aux craquelures dues à l'ozone dans des conditions statiques

General Information

• Status: Published
• ICS: 59.080.40 - Coated fabrics
• Technical Committee: ISO/TC 45/SC 4 - Products (other than hoses)
• Drafting Committee: ISO/TC 45/SC 4/WG 13 - Coated fabrics

RELATIONS

• Revised: ISO 3011:1997 - Rubber- or plastics-coated fabrics -- Determination of resistance to ozone cracking under static conditions
• Effective Date: 23-Apr-2020

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 3011
Fourth edition
Rubber- or plastics-coated fabrics —
Determination of resistance to ozone
cracking under static conditions
Supports textiles revêtus de caoutchouc ou de plastique —
Détermination de la résistance aux craquelures dues à l'ozone dans
des conditions statiques
PROOF/ÉPREUVE
Reference number
ISO 3011:2021(E)
ISO 2021
---------------------- Page: 1 ----------------------
ISO 3011:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO 2021 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 3011:2021(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

5 Apparatus ..................................................................................................................................................................................................................... 2

6 Test pieces ................................................................................................................................................................................................................... 2

6.1 Type .................................................................................................................................................................................................................. 2

6.2 Selection........................................................................................................................................................................................................ 2

6.3 Number .......................................................................................................................................................................................................... 2

7 Time intervals before testing .................................................................................................................................................................. 3

8 Test conditions ....................................................................................................................................................................................................... 3

8.1 Ozone concentration .......................................................................................................................................................................... 3

8.2 Temperature .............................................................................................................................................................................................. 3

8.3 Relative humidity .................................................................................................................................................................................. 3

8.4 Mounting of test pieces under stress and conditioning....................................................................................... 3

9 Procedure..................................................................................................................................................................................................................... 3

10 Test report ................................................................................................................................................................................................................... 4

© ISO 2021 – All rights reserved PROOF/ÉPREUVE iii
---------------------- Page: 3 ----------------------
ISO 3011:2021(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/

iso/ foreword .html.

This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,

Subcommittee SC 4, Products (other than hoses).

This fourth edition cancels and replaces the third edition (ISO 3011:1997), which has been technically

revised.
The main change compared to the previous edition is as follows:
— Clause 3 has been added;
— a subclause on relative humidity has been added.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www .iso .org/
...