ISO 16163:2005

Continuously hot-dipped coated steel sheet products — Dimensional and shape tolerances

ISO 16163:2005 applies to dimensional and shape tolerances for all continuously hot-dipped coated steel sheet products.

Tôles en acier revêtues en continu par immersion à chaud — Tolérances sur dimensions et forme

General Information

• Status: Withdrawn
• Publication Date: 08-Feb-2005
• Withdrawal Date: 08-Feb-2005
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: ISO/TC 17/SC 12 - Continuous mill flat rolled products
• Drafting Committee: ISO/TC 17/SC 12 - Continuous mill flat rolled products
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 09-Nov-2010

Relations

• Revised: ISO 16163:2010 - Continuously hot-dipped coated steel sheet products — Dimensional and shape tolerances
• Effective Date: 10-Jan-2009
• Revises: ISO 16163:2000 - Continuously hot-dipped coated steel sheet products — Dimensional and shape tolerances
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 16163
Second edition
2005-02-15

Continuously hot-dipped coated steel
sheet products — Dimensional and shape
tolerances
Tôles en acier revêtues en continu par immersion à chaud —
Tolérances sur dimensions et forme




Reference number
ISO 16163:2005(E)
©
ISO 2005

---------------------- Page: 1 ----------------------
ISO 16163:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16163:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16163 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 12, Continuous mill
flat rolled products.
This second edition cancels and replaces the first edition (ISO 16163:2000), which has been technically
revised.
© ISO 2005 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 16163:2005(E)

Continuously hot-dipped coated steel sheet products —
Dimensional and shape tolerances
1 Scope
This International Standard applies to dimensional and shape tolerances for all continuously hot-dipped
coated steel sheet products.
2 Dimensional tolerances
Dimensional tolerances are given in Tables 1 to 11.
Table 1 — Normal thickness tolerances for commercial, drawing, drawing aluminum-killed
and extra deep drawing stabilized interstitial free quality coils and cut lengths
Dimensions and tolerances in millimetres
a, b
Speci- Thickness tolerances
c
fied for specified thicknesses
width
u 0,4 > 0,4 u 0,6 > 0,6 u 0,8 > 0,8 u 1,0 > 1,0 u 1,2 > 1,2 u 1,6 > 1,6 u 2,0 > 2,0 u 2,5 > 2,5 u 3,0 > 3,0 u 4,0 > 4,0 u 5,0
600
± 0,05 ± 0,06 ± 0,08 ± 0,09 ± 0,10 ± 0,12 ± 0,18 ± 0,19 ± 0,21 ± 0,23 ± 0,25
u 1 200
> 1 200
± 0,06 ± 0,07 ± 0,09 ± 0,10 ± 0,11 ± 0,13 ± 0,20 ± 0,22 ± 0,23 ± 0,25 ± 0,27
u 1 500
> 1 500
— ± 0,09 ± 0,10 ± 0,11 ± 0,13 ± 0,15 ± 0,22 ± 0,24 ± 0,25 ± 0,27 ± 0,29
u 1 800
NOTE Thicknesses up to 1,6 mm are generally produced with cold-rolled substrate.
a
The thickness tolerances for sheet in coil form are the same as for sheet supplied in cut lengths but, in cases where welds are present, the tolerances
shall be double those given over a length of 15 m in the vicinity of the weld.
b
Given the difference in tolerances and physical properties of hot-rolled and cold-rolled sheet products, the user and the supplier may negotiate a
2
specific type of substrate. The relationship between coating mass in g/m and the thickness in micrometres can be retrieved from the respective standards.
c
Thickness is measured at any point on the sheet not less than 25 mm from a side edge.

© ISO 2005 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 16163:2005(E)
Table 2 — Normal thickness tolerances for structural-quality coils and cut lengths
Dimensions and tolerances in millimetres
a, b, c
Speci- Thickness tolerances
d, e
fied for specified thicknesses
width
u 0,4 > 0,4 u 0,6 > 0,6 u 0,8 > 0,8 u 1,0 > 1,0 u 1,2 > 1,2 u 1,6 > 1,6 u 2,0 > 2,0 u 2,5 > 2,5 u 3,0 > 3,0 u 4,0 > 4,0 u 5,0
600
± 0,06 ± 0,07 ± 0,09 ± 0,10 ± 0,11 ± 0,13 ± 0,18 ± 0,19 ± 0,21 ± 0,23 ± 0,25
u 1 200
> 1 200
± 0,07 ± 0,08 ± 0,10 ± 0,11 ± 0,12 ± 0,14 ± 0,20 ± 0,22 ± 0,23 ± 0,25 ± 0,27
u 1 500
> 1 500
— ± 0,10 ± 0,11 ± 0,12 ± 0,14 ± 0,16 ± 0,22 ± 0,24 ± 0,25 ± 0,27 ± 0,29
u 1 800
NOTE Thicknesses up to 1,6 mm are generally produced with cold-rolled substrate.
a
Thickness tolerances for sheet in coil form are the same as for sheets supplied in cut lengths but, in cases where welds are present, the tolerances
shall be double those given over a length of 15 m in the vicinity of the weld.
b
2
For specified strength levels of R = 360 N/mm and greater, increase the thickness tolerances by 10 %, by applying normal rounding-off procedures.
e
c
Tolerances for grade 550 shall be as agreed upon between the purchaser and the manufacturer.
d
Given the difference in tolerances and physical properties of hot-rolled and cold-rolled sheet products, the user and the supplier may negotiate a
2
specific type of substrate. The relationship between coating mass in g/m and the thickness in micrometres can be retrieved from the respective standards.
e
Thickness is measured at any point on the sheet not less than 25 mm from a side edge.
Table 3 — Restricted thickness tolerances for comm
...