ISO 4766:2024
(Main)Fasteners — Slotted set screws with flat point
Fasteners — Slotted set screws with flat point
This document specifies the characteristics of slotted set screws with flat point, in steel and stainless steel, with metric coarse pitch threads M1,2 to M12, and with product grade A. If in certain cases other specifications are requested, hardness classes and stainless steel grades can be selected from ISO 898-5 or ISO 3506-3, and dimensional options from ISO 888, ISO 965-1 or ISO 4753.
Fixations — Vis sans tête fendues à bout plat
Le présent document spécifie les caractéristiques des vis sans tête fendues à bout plat, en acier et en acier inoxydable, à filetage métrique à pas gros M1,2 à M12, et de grade A. Si dans certains cas d’autres spécifications sont requises, les classes de dureté et les grades d’acier inoxydable peuvent être choisis dans l'ISO 898-5 ou l'ISO 3506-3, et les options dimensionnelles dans l’ISO 888, l'ISO 965-1 ou l'ISO 4753.
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 4766
Third edition
Fasteners — Slotted set screws with
2024-06
flat point
Fixations — Vis sans tête fendues à bout plat
Reference number
ISO 4766:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 4766:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO 4766:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 2
5 Requirements and reference International Standards . 3
6 Marking and labelling . 4
6.1 Marking on product . .4
6.2 Labelling on package .4
7 Designation . 5
Bibliography . 6
© ISO 2024 – All rights reserved
iii
---------------------- Page: 3 ----------------------
ISO 4766:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(
...
Norme
internationale
ISO 4766
Troisième édition
Fixations — Vis sans tête fendues à
2024-06
bout plat
Fasteners — Slotted set screws with flat point
Numéro de référence
ISO 4766:2024(fr) © ISO 2024
---------------------- Page: 1 ----------------------
ISO 4766:2024(fr)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2024
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
© ISO 2024 – Tous droits réservés
ii
---------------------- Page: 2 ----------------------
ISO 4766:2024(fr)
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Dimensions . 2
5 Exigences et normes de référence internationales . 3
6 Marquage et étiquetage . 4
6.1 Marquage sur le produit .4
6.2 Étiquetage sur l’emballage .4
7 Désignation . 4
Bibliographie . 6
© ISO 2024 – Tous droits réservés
iii
---------------------- Page: 3 ----------------------
ISO 4766:2024(fr)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de propriété revendiqué à cet éga
...
FINAL DRAFT
International
Standard
ISO/FDIS 4766
ISO/TC 2/SC 11
Fasteners — Slotted set screws with
Secretariat: DIN
flat point
Voting begins on:
Fixations — Vis sans tête fendues à bout plat 2024-03-21
Voting terminates on:
2024-05-16
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 4766:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
FINAL DRAFT
ISO/FDIS 4766:2024(en)
International
Standard
ISO/FDIS 4766
ISO/TC 2/SC 11
Fasteners — Slotted set screws with
Secretariat: DIN
flat point
Voting begins on:
Fixations — Vis sans tête fendues à bout plat
Voting terminates on:
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
COPYRIGHT PROTECTED DOCUMENT
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2024
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 4766:2024(en) © ISO 2024
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO/FDIS 4766:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 2
5 Requirements and reference International Standards . 3
6 Marking and labelling . 4
6.1 Marking on product . .4
6.2 Labelling on package .4
7 Designation . 5
Bibliography . 6
© ISO 2024 – All rights reserved
iii
---------------------- Page: 3 ---------
...
ISO/FDIS 4766:2024(Een)
ISO TC 2/SC 11
Secretariat: DIN
Date: 2024-03-04
Fasteners — Slotted set screws with flat point
---------------------- Page: 1 ----------------------
ISO/FDIS 4766:2024(E)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part
of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or
mechanical, including photocopying, or posting on the internet or an intranet, without prior written
permission. Permission can be requested from either ISO at the address below or ISO’s member body
in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2024 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/FDIS 4766:2024(Een)
Contents
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Dimensions . 2
5 Requirements and reference International Standards . 4
6 Marking and labelling . 4
7 Designation . 5
Bibliography . 6
© ISO 2024 – All rights reserved iii
© ISO 2024 – All rights reserved
iii
---------------------- Page: 3 ----------------------
ISO/FDIS 4766:2024(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of
(a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received notice
of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents.www.iso.org/patents. ISO shall not be held responsible for
identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 11,
Fasteners with metric external thread, in collaboration with the European Committee for Standardization
(CEN) Tec
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.