ISO/FDIS 17842-3

Safety of amusement rides and amusement devices

Sécurité des manèges et des dispositifs de divertissement

General Information

• Status: Published
• ICS: 97.200.40 - Playgrounds
• Technical Committee: ISO/TC 254 - Safety of amusement rides and amusement devices
• Drafting Committee: ISO/TC 254/WG 3 - Operation and use
• Current Stage: 5020 - FDIS ballot initiated: 2 months. Proof sent to secretariat
• Start Date: 14-Dec-2021
• Completion Date: 14-Dec-2021

RELATIONS

• Revised: ISO 17842-3:2015 - Safety of amusement rides and amusement devices
• Effective Date: 14-Jan-2017

Standards Content (sample)

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 17842-3
ISO/TC 254
Safety of amusement rides and
Secretariat: GOST R
amusement devices —
Voting begins on:
2021-12-14
Part 3:
Voting terminates on:
Requirements for inspection during
2022-02-08
design, manufacture, operation and
use
Sécurité des manèges et des dispositifs de divertissement —
Partie 3: Exigences relatives à l'inspection pendant la conception,
fabrication et fonctionnement
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 17842-3:2021(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2021
---------------------- Page: 1 ----------------------
ISO/FDIS 17842-3:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on

the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below

or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
© ISO 2021 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/FDIS 17842-3:2021(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ..................................................................................................................................................................................... 1

3 Terms and definitions .................................................................................................................................................................................... 1

4 Requirements .......................................................................................................................................................................................................... 1

4.1 Initial approval — Procedures ................................................................................................................................................. 1

4.1.1 General ........................................................................................................................................................................................ 1

4.1.2 Review of design documents ................................................................................................................................... 2

4.1.3 Inspection of manufacturing process .............................................................................................................. 3

4.2 Pre-use inspection and review — Procedures .......................................................................................................... 4

4.3 In-service inspection (periodical test) ............................................................................................................................. 4

4.3.1 General ........................................................................................................................................................................................ 4

4.3.2 Inspection process ............................................................................................................................................................ 5

4.3.3 Electrical equipment ....................................................................................................................................................... 6

4.4 Installation examination ............................................................................................................................................................... 6

4.4.1 General ........................................................................................................................................................................................ 6

4.4.2 Extent of installation examinations .................................................................................................................. 6

Bibliography ................................................................................................................................................................................................................................ 8

iii
© ISO 2021 – All rights reserved
---------------------- Page: 3 ----------------------
ISO/FDIS 17842-3:2021(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to

the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see

www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 254, Safety of amusement rides and

amusement devices.

This second edition cancels and replaces the first edition (ISO 17842-3:2015), which has been

technically revised.
The main changes are as follows:
— references to ISO/TS 17929 have been removed;
— a reference to ISO 17842-1 has been added to 4.1.2, Review of design documents
— point g has been added to 4.1.3.1 Description;
— 4.1.3.3, Initial inspection and testing, has been updated;
— 4.2, Pre-use inspection and review – Procedures, has been added;
— 4.4, Installation examination, has been added;
A list of all parts in the ISO 17842 series can be found on the ISO website.

Any feedback or questions on this document should be directed to the user’s national standards body. A

complete listing of these bodies can be found at www.iso.org/members.html.
© ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 17842-3:2021(E)
Safety of amusement rides and amusement devices —
Part 3:
Requirements for inspection during design, manufacture,
operation and use
1 Scope

This document specifies the minimum requirements necessary for the independent inspections

of amusement devices designed, manufactured, operated and used according to ISO 17842-1 and

ISO 17842-2.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 9712, Non-destructive testing — Qualification and certification of NDT personnel

ISO 17842-1, Safety of amusement rides and amusement devices — Part 1: Design and manufacture

ISO 17842-2, Safety of amusement rides and amusement devices — Part 2: Operation and use

ISO/IEC 17020, Conformity assessment — Requirements for the operation of various types of bodies

performing inspection

IEC 60204-1, Safety of machinery — Electrical equipment of machines — Part 1: General requirements

3 Terms and definitions

For the purposes of this document, the terms and definitions given in ISO 17842-1, ISO 17842-2 and

ISO/IEC 17020 apply.

ISO and IEC maintain terminology databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Requirements
4.1 Initial approval — Procedures
4.1.1 General

The initial approval of any amusement device consists of review, inspections and tests to be carried out

as follows.

The inspection body performing the initial approval shall operate in accordance with ISO/IEC 17020.

© ISO 2021 – All rights reserved
---------------------- Page: 5 ----------------------
ISO/FDIS 17842-3:2021(E)

All safety-relevant design documents as well as the completed amusement device shall be subject

to review and inspection. After a successful inspection, a document confirming conformance with

ISO 17842-1 and ISO 17842-2 can be issued.

The results of the various reviews, inspections and tests shall become an integral part of the amusement

device log.
The initial approval of the amusement device shall comprise:
a) design review,
b) inspection of manufacturing process, and
c) initial inspection and testing.
4.1.2 Review of design documents
The review of design documents is an inspection of relevant design documents.

The design documents shall, where relevant, be reviewed, checked and accepted by an independent

body for:
— completeness,

— correctness of all the assumptions with respect to the input values for any analyses,

— correctness of all calculations, and
— compliance with applicable standards and specifications.
The design documents shall where relevant include the following:
— design risk assessment;
— design calculations;
— stress and fatigue analysis and stability verification;
— structural and mechanical parts;
— hydraulic and pneumatic parts;
— drive units, bearings;
— brakes and safety devices;
— design drawings;
— acceleration/containment details, according to ISO 17842-1;
— hydraulic/pneumatic specification;
— electrical/electronic specification including software details;
— mechanical/structural specification;
— installation, operation, maintenance and inspection information;
See ISO 17842-1:2015, 4.4, for the principles of structural analysis.
© ISO 2021 – All rights reserved
---------------------- Page: 6 ----------------------
ISO/FDIS 17842-3:2021(E)
4.1.3 Inspection of manufacturing process
4.1.3.1 Description

The inspection for the hereafter stated manufacturing requirements shall be made, when appropriate,

during the manufacturing process and completed before the permit to operate with passengers. As a

general requirement, the conformance of the parts, assemblies, components as well as their assembly

and combined effects within the entire installation shall be confirmed with respect to the approved

design documents.
This shall be covered by a report which confir
...