SIST EN 1143-2:2024

Secure storage units - Requirements, classification and methods of tests for resistance to burglary - Part 2: Deposit systems

This document specifies requirements and tests methods for deposit systems, and classifies the systems according to their burglary resistance and their resistance to the theft of deposits.
This document comprises two types of deposit system:
—   Night safes which provide depositing services for the customers of financial institutions without giving access to the content of the night safe.
—   Deposit safes which enable the personnel of a company to place money or valuables in safe custody without giving access to the content of the deposit safe. The installation condition for deposit safe according to this document is that the depositing functions are installed inside the premises of the company and are only disposable for the personnel of the company.
NOTE   Parts of a deposit system are a receiving unit, an input unit and in some cases, a chute.
This document includes design requirements for deposit systems controlled by programmable controllers and for the software for these. Controller hardware testing is restricted to mechanical or electromechanical attacks of electric motors, sensors, coils and similar devices; but software testing as attempts to influence controller software or controller hardware is not part of this document.
Deposit systems can have devices for functions such as user identification and/or counting and registration of money. Tests of and requirements for classification of such functions are not included.
This document does not cover protection of persons using the deposit system or the prevention of fraud committed by operators of the deposit system.

Wertbehältnisse - Anforderungen, Klassifizierung und Methoden zur Prüfung des Widerstandes gegen Einbruchdiebstahl - Teil 2: Deposit-Systeme

Dieses Dokument legt Anforderungen und Prüfverfahren für Deposit-Systeme fest und klassifiziert die Systeme nach ihrem Widerstand gegen Einbruchdiebstahl und Diebstahl der Deposits.
Dieses Dokument umfasst zwei Arten von Deposit-Systemen:
-   Nachttresore, die Kunden von Kreditinstituten ohne Zugriff auf den Inhalt des Nachttresors zur Verfügung stehen.
-   Deposit-Safes, die Angestellten eines Unternehmens ohne Zugriff auf den Inhalt des Deposit-Safes zum Deponieren von Geld oder Werten zur Verfügung stehen. Voraussetzung für die Installation des Deposit-Safes nach diesem Dokument ist, dass die Depositfunktionen sich in den Räumen des Unternehmens befinden und nur den Angestellten des Unternehmens zugänglich sind.
ANMERKUNG   Ein Deposit-System besteht aus einer Aufnahmeeinheit, einer Einwurfeinheit sowie ggf. einem Fallschacht.
Dieses Dokument umfasst Konstruktionsanforderungen für Deposit-Systeme mit programmierbaren Steuerungen einschließlich der dazugehörigen Software. Die Prüfung der Steuerungshardware ist auf mechanische oder elektromechanische Angriffe auf elektrische Motoren, Sensoren, Spulen und ähnliche Bauteile beschränkt; Softwareprüfungen wie Versuche, die Steuerungssoftware oder Steuerungshardware zu beeinflussen, sind jedoch nicht Teil dieses Dokuments.
Deposit-Systeme können über Bauteile verfügen, die Funktionen, wie z. B. Nutzeridentifikation bzw. Zählen und Registrieren von Geld steuern. Prüfungen und Anforderungen für die Klassifizierung dieser Funktionen sind nicht enthalten.
Dieses Dokument behandelt nicht den Schutz von Personen, die das Deposit-System nutzen, oder den Schutz vor Betrug durch das Bedienpersonal.

Unités de stockage en lieux sûrs - Exigences, classification et méthodes d'essai pour la résistance à l'effraction - Partie 2: Systèmes de dépôt

Le présent document spécifie les exigences et les méthodes d'essai relatives aux systèmes de dépôt et classe ces systèmes en fonction de leur résistance à l'effraction et de leur résistance au vol des dépôts.
Le présent document traite de deux types de systèmes de dépôt :
-   les coffres « dépôt de nuit », qui offrent des services de dépôt aux clients d'institutions financières sans donner accès au contenu du coffre « dépôt de nuit » ;
-   les coffres « dépôt de fonds », qui permettent au personnel d'une entreprise de placer de l'argent ou des objets de valeur en lieu sûr sans donner accès au contenu du coffre « dépôt de fonds ». La condition d'installation pour le coffre « dépôt de fonds » conformément au présent document est que les fonctions de dépôt soient installées à l'intérieur des locaux de l'entreprise et qu'elles ne soient à disposition que du personnel de l'entreprise.
NOTE   Un système de dépôt se compose d'une unité de réception, d'une unité d'introduction et, dans certains cas, d'une chute.
Le présent document comprend des exigences de conception pour les systèmes de dépôt commandés par des contrôleurs programmables et pour les logiciels correspondants. L'essai relatif au matériel du contrôleur est restreint aux attaques mécaniques ou électromécaniques de moteurs électriques, de capteurs, de bobines et dispositifs similaires. Toutefois, les essais portant sur le logiciel, consistant, par exemple, à tenter d'influencer le logiciel du contrôleur ou le matériel du contrôleur ne font pas partie du présent document.
Les systèmes de dépôt peuvent être équipés de dispositifs assurant des fonctions telles que l'identification de l'utilisateur et/ou le décompte et l'enregistrement de l'argent. Les essais et exigences relatifs à la classification de ce type de fonctions ne sont pas inclus.
Le présent document ne traite pas de la sécurité des personnes utilisant les systèmes de dépôt, ni de la prévention de fraude commise par les opérateurs du système de dépôt.

Varnostne shranjevalne enote - Zahteve, klasifikacija in metode preskušanja protivlomne odpornosti - 2. del: Depozitni sistemi

Ta dokument določa zahteve in preskusne metode za depozitne sisteme ter razvršča sisteme glede na njihovo protivlomno odpornost in odpornost proti kraji depozitov.
Ta dokument vključuje dve vrsti depozitnih sistemov:
–   nočne trezorje, ki zagotavljajo depozitne storitve strankam finančnih institucij in ne omogočajo dostopa do vsebine nočnega trezorja;
–   depozitne trezorje, ki zaposlenim v podjetju omogočajo varno hranjenje denarja ali dragocenosti in ne omogočajo dostopa do vsebine depozitnega trezorja. Pogoj namestitve depozitnega trezorja v skladu s tem dokumentom je, da morajo biti depozitne funkcije nameščene v prostorih podjetja in morajo biti na voljo le zaposlenim v podjetju.
OPOMBA:   Deli depozitnega sistema so prevzemna enota, enota za vnos in v nekaterih primerih jašek.
Ta dokument vključuje zahteve za načrtovanje depozitnih sistemov, ki jih nadzorujejo programirljivi krmilniki, in programsko opremo programirljivih krmilnikov. Preskušanje strojne opreme krmilnikov je omejeno na mehanske in elektromehanske napade električnih naprav, senzorjev, tuljav in podobnih naprav; preskušanje programske opreme z namenom vplivanja na programsko ali strojno opremo krmilnika pa ni vključeno v dokument.
Depozitni sistemi imajo lahko naprave za funkcije, kot so identifikacija uporabnika in/ali štetje ter registracija denarja. Preskusi takih funkcij in zahteve za razvrstitev takih funkcij niso vključeni.
Ta dokument ne zajema zaščite oseb, ki uporabljajo depozitni sistem, ali preprečevanje goljufij, ki jih storijo upravljavci depozitnega sistema.

General Information

• Status: Published
• Public Enquiry End Date: 01-Aug-2023
• Publication Date: 22-Aug-2024
• ICS: 13.310 - Protection against crime
• Technical Committee: PPV - Secure storage units and door locks
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 21-Aug-2024
• Due Date: 26-Oct-2024
• Completion Date: 23-Aug-2024
• Directive: 2020-01-0063 - Pravilnik o pogojih in merilih za izdajatelja pomnilniških kartic za zapisovalno opremo v cestnih prevozih ter načinu oblikovanja in določanja cene za izdajo kartice
• Ref Project: EN 1143-2:2024 - Secure storage units - Requirements, classification and methods of tests for resistance to burglary - Part 2: Deposit systems

Relations

• Replaces: SIST EN 1143-2:2014 - Secure storage units - Requirements, classification and methods of tests for resistance to burglary - Part 2: Deposit systems
• Effective Date: 01-Oct-2024

Overview - EN 1143-2:2024 (CEN)

EN 1143-2:2024 is the CEN European standard that defines requirements, classification and laboratory test methods for deposit systems (night safes and deposit safes). It specifies how deposit systems are assessed for burglary resistance and for resistance to the theft of deposits, including design requirements for mechanical, electromechanical and limited controller-hardware attacks. The standard supersedes EN 1143-2:2014 and is intended for manufacturers, test laboratories, specifiers and end‑users of secure deposit equipment.

Key topics and technical requirements

• Scope and product types: Covers two main deposit system types - night safes (public depositing, content not accessible to customers) and deposit safes (internal company depositing accessible only to authorised personnel). Parts of a deposit system include a receiving unit, input unit and sometimes a chute.
• Classification: Systems are classified into resistance grades consistent with EN 1143-1 series, with additional designations (for example new T2 tooling designation) to reflect updated tool-threat profiles.
• Test methods: Detailed laboratory test programmes for:
  • Tool attack tests (partial/complete access)
  • Deposit-forcing and deposit-fishing tests (removal of deposited items)
  • Explosive (EX) and gas (GAS) test options
  • Fixing/anchoring tests (conditions depend on deposit system type)
• Controller and software: Design requirements cover programmable controllers and associated software, but the standard restricts testing to mechanical/electromechanical attacks on controller hardware; active attempts to manipulate controller software are outside the scope.
• Exclusions: Tests for user protection, prevention of operator fraud, and classification of peripheral functions (e.g., user identification, counting) are not covered.
• Updates: 2024 edition adds tests and design categories (e.g., semi‑integrated deposit safe, built‑in systems), updates explosive/gas test rules and aligns cryptography requirements with EN 17646.

Applications - who uses EN 1143-2:2024

• Manufacturers and designers of night safes, deposit safes and integrated deposit systems for banks, retailers, petrol stations and cash-handling businesses.
• Independent testing laboratories performing accredited burglary and deposit-theft tests.
• Procurement officers, security consultants and insurers specifying minimum resistance grades for cash handling and secure storage.
• Regulators and standards bodies comparing product performance across Europe.

Related standards

• EN 1143-1:2019 - Safes, ATM safes, strongroom doors and strongrooms
• EN 1300 / EN 17646 - High security lock classification (including distributed systems)
• EN ISO/IEC 17025 - Laboratory competence for testing

Keywords: EN 1143-2:2024, deposit systems, night safes, deposit safes, burglary resistance, test methods, CEN, deposit-forcing, explosive test, secure storage units.

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2024
Varnostne shranjevalne enote - Zahteve, klasifikacija in metode preskušanja
protivlomne odpornosti - 2. del: Depozitni sistemi
Secure storage units - Requirements, classification and methods of tests for resistance
to burglary - Part 2: Deposit systems
Wertbehältnisse - Anforderungen, Klassifizierung und Methoden zur Prüfung des
Widerstandes gegen Einbruchdiebstahl - Teil 2: Deposit-Systeme
Unités de stockage en lieux sûrs - Exigences, classification et méthodes d'essai pour la
résistance à l'effraction - Partie 2: Systèmes de dépôt
Ta slovenski standard je istoveten z: EN 1143-2:2024
ICS:
13.310 Varstvo pred kriminalom Protection against crime
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 1143-2
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2024
EUROPÄISCHE NORM
ICS 13.310 Supersedes EN 1143-2:2014
English Version
Secure storage units - Requirements, classification and
methods of tests for resistance to burglary - Part 2:
Deposit systems
Unités de stockage en lieux sûrs - Prescriptions, Wertbehältnisse - Anforderungen, Klassifizierung und
classification et méthodes d'essai pour la résistance à Methoden zur Prüfung des Widerstandes gegen
l'effraction - Partie 2 : Systèmes de dépôt Einbruchdiebstahl - Teil 2: Deposit-Systeme
This European Standard was approved by CEN on 3 June 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1143-2:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
3.1 Deposit system definitions . 8
3.2 Deposit tool attack definitions . 10
4 Classification and requirements . 11
4.1 Classification. 11
4.2 General requirements . 12
4.3 Requirements for the receiving units . 12
4.4 System requirements . 16
5 Technical documentation . 19
6 Test specimen . 21
7 Test program . 21
8 Tool attack test . 23
8.1 General. 23
8.2 Principle . 23
8.3 Testing team . 24
8.4 Apparatus . 24
8.5 General test conditions . 25
8.6 General test procedure . 26
8.7 Calculation of resistance values . 27
8.8 Test record – tool attack test . 28
9 Access tool attack tests . 29
9.1 Partial access – tool attack test . 29
9.2 Complete access – tool attack test . 30
9.3 Partial access EX – explosive tool attack test . 30
9.4 Partial access GAS – explosive tool attack test . 32
10 Deposit tool attack tests (removal of deposits) . 34
10.1 General for all deposit tool attack tests . 34
10.2 Test conditions for Deposit forcing tool attack test . 35
10.3 Test conditions for Deposit forcing EX tool attack test . 36
10.4 Test conditions for Deposit forcing GAS tool attack test . 37
10.5 Test conditions for Deposit fishing tool attack test . 39
10.6 Test conditions for Deposit fishing tool attack test . 40
10.7 Test conditions for Last deposit trapping tool attack test . 40
10.8 Test conditions for Deposit repeated trapping tool attack test . 41
11 Fixing system tool attack tests . 42
11.1 Fixing system – tool attack test without force . 42
11.2 Fixing system – tool attack test with force . 43
12 Test report and test records . 46
12.1 Test report . 46
12.2 Test records . 47
13 Marking . 47
Annex A (informative) Examples of different designs of deposit systems . 48
Annex B (informative) Examples of integrated and distributed deposit systems . 49
B.1 Integrated deposit system . 49
B.2 Semi-integrated deposit safe . 50
B.3 Different distributed deposit systems . 51
Annex C (normative) Additional tools for deposit tool attack tests . 54
Annex D (informative) Structure of test clauses . 55

European foreword
This document (EN 1143-2:2024) has been prepared by Technical Committee CEN/TC 263 “Secure
storage of cash, valuables and data media”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2025, and conflicting national standards shall
be withdrawn at the latest by February 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1143-2:2014.
a) requirements for the additional T2 test have been added (4.1, 5.3, 8.4.1 and Clause 13), Table 1,
Table 2, Table 3, Table 4 and Table 5). Products tested with these new tools which are listed in
Annex B of EN 1143-1 have a 'T2' designation behind the resistance grade;
b) Requirements for built-in deposit systems have been added (see 9.1.1 and 9.2.1);
c) A new type of deposit system “semi-integrated deposit safe” has been added (see 3.1.11, 3.1.17, 4.4.1,
4.4.3, 5.10 e) and B.2);
d) The anchoring test with force now depends on the type of deposit system and (11.2 and Table 10);
e) An additional test condition for cutting steel sheets has been added (Clause 2 and 8.5.3);
f) The cryptography requirements were raised to those of EN 17646 (Clause 2, 4.4.4.1 and 5.13);
g) Updates have been integrated for the optional solid explosive test, above all: The explosive mass for
the EX-option in 9.3.4 and 10.3.3 was changed to “active explosive mass”, instead of specific energy
the explosive heat of the PETN is defined (9.3.3); the detonation velocity of the PETN was raised from
(7 000 ± 500) m/s to (7 500 ± 500) m/s (9.3.3); the tolerance of the active explosive charge mass has
been changed from ± 1 g to ± 2 % (Table 9) and the shape of the explosive charge shall now be
spherical (9.3.8);
h) For the GAS option the 100 litres limitation has been deleted (9.4.4), the gas explosive has been
defined more precise (9.4.3), the test conditions for the deposit forcing GAS tool attack test have been
updated (10.4.7.3 and 10.4.7.4) and documentation requirements have been added (5.9 b));
i) Annex C has changed from informative to normative and the tools are now explicitly classified as
category A tools (8.4.1);
j) Update of references to the newer EN 1143-1:2019;
k) Integration of high security locks of EN 17646 (Table 2, Table 3, 10.2.1, 10.3.1, 10.4.1, 10.5.1, 10.6.1,
10.7.1 and 10.8.1);
l) Minor updates for the test report requirements (12.1);
m) Editorial adaptions throughout the standard (see 3.1.10, 3.1.12, 4.3.3, 4.4.2.3, 8.4.1, 8.4.2, 8.6.3,
10.3.1, 10.4.1, 10.7.2, 10.8.2, 11.2.3, 13, Annex A, B.3, Table 1, Table 2, Table 3, Table 4, Table 5).
This document is one of a series of product standards for secure storage units of different types.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
Introduction
This document gives the possibility to classify deposit systems according to their resistance to burglary
attacks. The laboratory tests simulate known attack methods and such methods and tools which are
supposed to be used for attacking these types of products.
Human intervention tests are included. The results and repeatability of these depend on the skill of the
testing team. Testing laboratories are therefore recommended to participate in inter-laboratory activities
to ensure that the standard is used in an overall common approach. Otherwise, results from different
laboratories may differ too much.
The tests and requirements in this document are based on the following assumptions (conditions) of use
and installation of deposit systems:
Deposit safe: For deposit safes, the depositing functions are inside the premises of the company and are
only intended to be disposable for the authorized personnel of the company. It is assumed that the
authorized personnel carry out the depositions. Deposit safes are installed so the deposit functions are
not available for the public. It is also assumed that a burglar does not have the code or key to the deposit
functions for some kind of attacks.
Night safe: For night safes, the depositing functions are available to customers of financial institutions
and, if locked, are disposable only for the authorized personnel of the customer. Night safes are installed
so the deposit functions are available also for the public. It is also assumed that a burglar may have the
code or key to the depositing functions.
Receiving units are basically safes (see EN 1143-1) which have apertures necessary for operation of the
deposit system.
Examples of different design of deposit systems are given in Annex A.
Deposit systems are classified in a system of grades, corresponding to that of EN 1143-1. In addition,
there are requirements and test methods for burglary and manipulation of the deposit system functions.
1 Scope
This document specifies requirements and tests methods for deposit systems, and classifies the systems
according to their burglary resistance and their resistance to the theft of deposits.
This document comprises two types of deposit system:
— Night safes which provide depositing services for the customers of financial institutions without
giving access to the content of the night safe.
— Deposit safes which enable the personnel of a company to place money or valuables in safe custody
without giving access to the content of the deposit safe. The installation condition for deposit safe
according to this document is that the depositing functions are installed inside the premises of the
company and are only disposable for the personnel of the company.
NOTE Parts of a deposit system are a receiving unit, an input unit and in some cases, a chute.
This document includes design requirements for deposit systems controlled by programmable
controllers and for the software for these. Controller hardware testing is restricted to mechanical or
electromechanical attacks of electric motors, sensors, coils and similar devices; but software testing as
attempts to influence controller software or controller hardware is not part of this document.
Deposit systems can have devices for functions such as user identification and/or counting and
registration of money. Tests of and requirements for classification of such functions are not included.
This document does not cover protection of persons using the deposit system or the prevention of fraud
committed by operators of the deposit system.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1143-1:2019, Secure storage units — Requirements classification and methods of test for resistance to
burglary - Part 1: Safes, ATM safes, strongroom doors and strongrooms
EN 1300, Secure storage units — Classification for high security locks according to their resistance to
unauthorized opening
EN 10051, Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels —
Tolerances on dimensions and shape
EN 17646, Secure storage units — Classification for high security locks according to their resistance to
unauthorized opening — Distributed systems
EN ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
(ISO/IEC 17025)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1143-1 and EN 1300 and the
following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1 Deposit system definitions
3.1.1
deposit system
assembly of a receiving unit and an input unit and optionally a chute for their inter-connection and with
all features for depositing and protection
Note 1 to entry: Deposit systems can be either deposit safes or night safes.
Note 2 to entry: A deposit system serves the purpose to securely accept and securely store deposits of cash and/or
valuables.
3.1.2
deposit safe
deposit system whose requirements are related to the security provisions needed to enable employees
to deposit into the receiving unit without having to unlock the receiving unit door
Note 1 to entry: The input unit of this system is intended to be used only by the employees and not be placed in a
public area.
3.1.3
night safe
deposit system whose security requirements relate to use by financial institutions for providing a secure
receiving service for customer deposits without having to unlock the receiving unit door
Note 1 to entry: The input unit of this system is intended to be used by the customers of financial institutions and
can be placed in a public area.
3.1.4
receiving unit
secure storage unit with openings necessary to accommodate a deposit system
3.1.5
internal space
interior of the receiving unit which is bounded by the inside surfaces and the boltwork cover plate(s) of
the door of the receiving unit body
3.1.6
design capacity
usable internal space for storing deposits
3.1.7
input unit
user-access facility into which deposits are placed for passing into the receiving unit
Note 1 to entry: Access to input units may be controlled by locks or devices that may provide identification of the
depositor.
Note 2 to entry: In this context ‘input unit’ refers to the device intended for deposit items, as opposed to the input
unit for locks in EN 1300.
3.1.8
chute
optional connection between input unit and receiving unit through which the deposit passes
3.1.9
deposit
item placed into the input unit and intended for passing into the receiving unit
Note 1 to entry: The deposit may be money or valuables that are deposited in special containers, bags or envelopes,
or single bank notes or bunches of bank notes.
3.1.10
integrated deposit system
deposit system controlled by programmable controllers in which the physical deposit sequences cannot
be changed through links to devices outside the receiving unit (see 4.4.2)
Note 1 to entry: For an example of an integrated deposit system, see Annex B, Figure B.1.
Note 2 to entry: It is permitted that the controller of the integrated deposit system transmits data about the system
status and events.
3.1.11
semi-integrated deposit safe
deposit safe controlled by programmable controllers in which the physical deposit sequences cannot be
changed through links to devices outside the deposit safe (see 4.4.3)
Note 1 to entry: For an example of a semi-integrated deposit safe, see Annex B, Figure B.2.
Note 2 to entry: It is permitted that the controller of the semi-integrated deposit system transmits data about the
system status and events.
3.1.12
distributed deposit system
deposit system controlled by programmable controllers in which the physical deposit sequences can be
changed through links to devices outside the receiving unit and even the deposit system (see 4.4.4)
Note 1 to entry: For an example of a distributed deposit system, see Annex B.
3.1.13
base
any part of a deposit system which is between the receiving unit and the surface to which it is to be
anchored
Note 1 to entry: A base is used to place a deposit system input unit at a convenient height for use.
3.1.14
deposit sequence
all steps in the cycle that a deposit system performs from when it has been activated by the depositor and
until the system has returned to the position from where it can be activated again
3.1.15
controller unit
device consisting of electronic hardware and software and have the purpose to operate the deposit
sequence
3.1.16
remote access
communication from outside the receiving unit, through a data link that gives the possibility to control /
influence the deposit sequence of a distributed system
3.1.17
user level
software functions usable by the depositor that do not change the general function of the deposit system
and do not change user specific settings of other depositors or users
Note 1 to entry: These software functions may be needed to deposit money, receive an envelope, get a receipt, etc.
3.2 Deposit tool attack definitions
NOTE The deposit tool attacks in 3.2.1 to 3.2.7 are different types of attacks with the intention to remove one
or several deposits from the deposit system. Detailed information about conditions for testing and criteria are given
in Clause 10.
3.2.1
forcing
destructive attack with the intention to remove several deposits from the receiving unit
3.2.2
forcing EX
destructive attack including plastic explosives with the intention to remove several deposits from the
receiving unit
3.2.3
forcing GAS
destructive attack including gas explosives with the intention to remove several deposits from the
receiving unit
3.2.4
deposit retrieval
manipulative non-destructive attack without leaving traces with the intention to remove one deposit
from the receiving unit
3.2.5
fishing
manipulative non-destructive attack with the intention to remove several deposits from the receiving
unit from the still functioning deposit system
3.2.6
trapping last deposit
manipulative attack by means of introduction of devices that prevent one deposit from reaching the
receiving unit and then to remove it from the deposit system
3.2.7
repeated trapping
manipulative attack by means of introduction of devices that prevent several deposits from reaching the
receiving unit and then to remove them from the still functioning deposit system
4 Classification and requirements
4.1 Classification
Deposit systems are classified in different grades according to Table 1. Deposit safes are designated with
“D” and night safes are designated with “N”. In addition to the basic grades there are three possible
options: “T2”, “EX” and “GAS”. These can be individual or in combination with each other (for example N-
V EX GAS).
The “T2” indicates that in addition to the tools listed in EN 1143-1:2019, Annex A, the deposit system may
also be attacked with the tools of EN 1143-1:2019, Annex B. The T2 tools of EN 1143-1:2019, Annex B
are only used, if the applicant applies for T2 designation. For the T2 designation all the tests and
requirements in this document that refer to Annex A of EN 1143-1:2019 are additionally applicable with
the tools of EN 1143-1:2019, Annex B.
The “EX” indicates that the deposit system also complies with the requirements for Partial access EX –
explosive tool attack test and Deposit forcing EX tool attack test.
The “GAS” indicates that the deposit system also complies with the requirements for Partial access GAS –
explosive tool attack test and Deposit forcing GAS tool attack test.
Table 1 — Possible classifications of deposit systems
Deposit safe (D) classification Night safe (N) classification
a a
Basic grading Options Basic grading Options
EX GAS EX GAS
D-0 –- –- –- –- –-
D-I –- –- –- –- –-
D-II D-II EX D-II GAS N-II N-II EX N-II GAS
D-III D-III EX D-III GAS N-III N-III EX N-III GAS
D-IV D-IV EX D-IV GAS N-IV N-IV EX N-IV GAS
D-V D-V EX D-V GAS N-V N-V EX N-V GAS
–- –- –- N-VI N-VI EX N-VI GAS
–- –- –- N-VII N-VII EX N-VII GAS
–- –- –- N-VIII N-VIII EX N-VIII GAS
–- –- –- N-IX N-IX EX N-IX GAS
–- –- –- N-X N-X EX N-X GAS
NOTE 1 The basic grade limits are the same as those of EN 1143-1, where applicable.
NOTE 2 If the optional T2 test is fulfilled, a T2 is added to the classification.
a
All additional requirements for EX respective GAS shall be fulfilled.
4.2 General requirements
4.2.1 Holes in protection material
There shall be no holes through the protection material of an input unit or chute other than those
necessary for user identification (e.g. locks, card readers, etc.), cables, and insertion of deposits.
There shall be no holes through the protection material of a receiving unit other than those for locks,
cables, anchoring and the aperture for the input unit or chute.
4.2.2 Cable hole
Deposit systems of grade III and higher shall either have a hole for a cable or a preparation enabling a
connection to be made to an alarm system after the secure storage unit has been installed.
Unused cable entry openings shall be obstructed or plugged by means that cannot be removed from the
outside without leaving visible traces.
4.2.3 User instructions
Deposit systems shall be provided with instructions for:
— operating and maintenance, including instructions in respect of the locks,
— anchoring,
— system installation for built-in deposit systems,
— deposit sizes recommended,
— the depositor.
4.3 Requirements for the receiving units
4.3.1 Dimensions
The receiving unit shall, when closed, have at least one internal side ≤ 1 m.
4.3.2 Boltwork cover plate
Receiving unit shall have an internal boltwork cover plate which prevents unauthorized viewing of the
locks and boltwork, and access to them, when the door is open. Boltwork cover plates shall be secured so
that they cannot be opened or removed by an unauthorized person without leaving visible traces.
Boltwork cover plates may be secured so that they only can be opened or removed by using the correct
key or code or by breaking a seal.
4.3.3 Locks: amount and class
The receiving unit shall be fitted with locks conforming to EN 1300 or EN 17646, in accordance with
Tables 2 and 3 of this document.
Time locks and/or time delay locks may be mounted in addition to the locks listed in Tables 2 and 3.
4.3.4 Partial and complete access
When tested in accordance with Clause 9, the receiving unit shall provide the resistance value to complete
access and partial access, partial access EX (optional), partial access GAS (optional) specified in Tables 2
and 3 for the relevant grade.
These requirements do not apply to the aperture for the input unit or chute.
4.3.5 Fixing system
Receiving units in deposit systems shall have a fixing system by which they can be anchored. When tested
in accordance with 11.1 and 11.2, the fixing system shall provide the resistance values specified in
Tables 2 and 3 for the relevant grade.
Table 2 — Minimum requirements for deposit safe (D) receiving unit
Grade Access tool attack tests Anchoring Tool attack Additional Locks Additional
strength test on fixing requirements requirements for EX
(Clauses 9.1 and 9.2)
(Clause 11.2) attachment for post- and GAS designation
Access tool attack test T2
(Clause 11.1) anchoring (optional)
(Clause 4.1)
forcing test (Clauses 9.3 and 9.4)
(Clause 11.2)
c
Resistance value for Required Resistance Post-anchoring Quantity Class Post-detonation
c b c
force value resistance according resistance value
Partial access Complete
c
value to EN 1300
access
/ EN 17646
RU RU kN RU RU RU
a
D-0 30 30 50 30 18 1 A / A(DS) - - -
a
D-I 30 50 50 30 18 1 A / A(DS) - - -
D-II 50 80 50 50 22 1 A / A(DS) 4
D-III 80 120 50 50 22 1 B / B(DS) 6
D-IV 120 180 100 50 22 2 B / B(DS) 9
D-V 180 270 100 50 22 2 B / B(DS) 14
a
EX and GAS designation are not permitted for resistance grades D-0 and D-I.
b
Resistance value for partial access.
c
If the tool test is performed according to 4.1 (T2), the resistance value shall be achieved according to 4.1 (T2).
Table 3 — Minimum requirements for night safe (N) receiving unit
Grade Access tool attack tests Anchoring Tool attack Additional Locks Additional
strength test on fixing requirements requirements for EX
(Clauses 9.1 and 9.2)
(Clause 11.2) attachment for post- and GAS designation
Access tool attack test T2
(Clause 11.1) anchoring (optional)
(Clause 4.1)
forcing test (Clauses 9.3 and 9.4)
(Clause 11.2)
b
Resistance value for Required Resistance Post-anchoring Quantity Class Post-detonation
b a b
force value resistance according resistance value
Partial access Complete
b
value to EN 1300
access
/ EN 17646
RU RU kN RU RU RU
N-II 50 80 50 50 22 1 A / A(DS) 4
N-III 80 120 50 50 22 1 B / B(DS) 6
N-IV 120 180 100 50 22 2 B / B(DS) 9
N-V 180 270 100 50 22 2 B / B(DS) 14
N-VI 270 400 100 70 22 2 C / C(DS) 20
N-VII 400 600 100 120 22 2 C / C(DS) 30
N-VIII 550 825 100 160 22 2 C / C(DS) 41
N-IX 700 1 050 100 210 22 2 C / C(DS) 53
N-X 900 1 350 100 280 22 2 C / C(DS) 68
a
Resistance value for partial access.
b
If the tool test is performed according to 4.1 (T2), the resistance value shall be achieved according to 4.1 (T2).
4.4 System requirements
4.4.1 General
System requirements are related to the resistance of removal of one or more deposits from the system
under conditions specified under Clause 10 for different types of deposit tool attack tests.
Deposit systems in which the deposit sequence and other sequences are controlled by programmable
controllers shall conform to 4.4.2 (for integrated deposit systems), 4.4.3 (for semi-integrated deposit
safes) and 4.4.4 (for distributed deposit systems).
4.4.2 Integrated deposit systems
4.4.2.1 Predefined deposit sequence and other predefined sequences shall be controlled by devices
inside the receiving unit.
4.4.2.2 It shall not be possible to change the software containing the predefined sequences unless the
receiving unit door is open.
4.4.2.3 The controller unit shall be secured by a protective cover. It shall not be possible to open or
remove the cover by an unauthorized person without leaving visible traces or result in operation failure.
Means shall be provided to indicate that tampering of the controller unit has taken place.
4.4.2.4 From outside of the receiving unit it shall only be possible to initiate predefined sequences in
the deposit system.
4.4.2.5 The software controlling the sequences of the deposit system capture shall be identified with
a unique version number.
4.4.3 Integrated deposit safes with external user interface for local authorization (semi-
integrated deposit safes)
NOTE The following requirements are only applicable for deposit safes (see Figure B.2).
4.4.3.1 Predefined deposit sequence and other predefined sequences shall be controlled by devices
inside the input unit.
4.4.3.2 The controller unit shall be secured by a protective cover, e.g. input unit housing by 2 mm
mild steel. It shall not be possible to open or remove the cover by an unauthorized person without leaving
visible traces and result in operation failure. Means shall be provided to indicate that tampering of the
controller unit has taken place.
4.4.3.3 From outside of the receiving unit it shall only be possible to initiate predefined sequences in
the deposit system.
4.4.3.4 The software controlling the sequences of the deposit system capture shall be identified with
a unique version number.
4.4.3.5 Any additional controller unit of the deposit safe shall be secured by a protective cover, e.g.
housing by 2 mm mild steel. It shall not be possible to open or remove the cover by an unauthorized
person without leaving visible traces and result in operation failure.
4.4.3.6 For the use of the deposit safe, there shall be a defined user hierarchy in the software
(operating system):
— User level: used for depositing money inside to the receiving unit. The user shall not be able to open
the cover, e.g. input unit housing;
— Admin level 1: used for the reset of the input unit mechanism resp. banknote reader after a failure,
e.g. deposit / banknote jam;
— Admin level 2: additional to Admin level 1, used for the reset of the system after a failure or to
authorize the access for maintenance purposes through the controller units by an external user
interface unit or data processor (the additional cover for the controller unit of the deposit safe has to
be open).
4.4.3.7 The different admin levels shall be secured by an individual authorization e.g. PIN, minimum
6 digits or adequate means.
4.4.3.8 If the input unit system or banknote reader has interfaces, access shall be secured by means
so that removal of these means leaves visible traces.
4.4.3.9 Every opening of the covers shall be recorded and stored as secured data by the controller
unit.
4.4.3.10 The instructions shall include an information that it cannot be excluded that the stored data
may be lost due to destruction.
4.4.4 Distributed deposit systems
4.4.4.1 If the predefined deposit sequence and other predefined sequences are controlled or changed
from outside the receiving unit, the control signals shall be protected by cryptography. The requirements
for cryptography described in EN 17646 are applicable also for distributed systems.
4.4.4.2 The software controlling the sequences of deposit system shall be identified with a unique
version number.
4.4.4.3 The controller unit shall be protected by a lock and access control such that unauthorized
entry results in visible traces or in operation failure.
4.4.5 Resistance to deposit tool attacks
When tested in accordance with Clause 10, a deposit safe shall provide the resistance to forcing, forcing
EX (option), forcing GAS (option), fishing and deposit retrieval specified in Table 4 for the relevant grade.
When tested in accordance with Clause 10, a night safe shall provide the resistance to forcing, forcing EX
(option), forcing GAS (option), fishing, deposit retrieval, trapping last deposit and repeated trapping
specified in Table 5 for the relevant grade.
Table 4 — Minimum requirements for deposit tool attacks for deposit safes (D)
Resistance General Additional requirements for
grade EX and GAS designation
(optional)
Forcing Fishing Deposit retrieval Forcing
(subclause 10.2) (subclause 10.5) (subclause 10.6) (subclauses 10.3 and 10.4)
b b
Resistance Resistance value Resistance value Resistance value
b b
value
RU RU RU RU
a
D-0 30 30 30 - - -
a
D-I 30 30 50 - - -
D-II 50 50 80 4
D-III 80 80 120 6
D-IV 120 120 180 9
D-V 180 180 270 14
a
EX and GAS designation are not permitted for resistance grade D-0 and D-I.
b
If the tool test is performed according to 4.1 (T2), the resistance value shall be achieved according to 4.1 (T2).
Table 5 — Minimum requirements for deposit tool attacks for night safes (N)
Resistance General Additional
grade requirements
for EX and GAS
designation
(optional)
Forcing Fishing Deposit Trapping last Repeated Forcing
(subclause (subclause retrieval deposit trapping (subclauses
(subclause 10.6) (subclause 10.7) (subclause 10.8)
10.2) 10.5) 10.3 and 10.4)
Resistance Resistance Resistance Resistance Resistance Resistance
a a a a a a
value value value value value value
RU RU RU RU RU RU
N-II 50 50 80 20 50 4
N-III 80 80 120 30 80 6
N-IV 120 120 180 40 120 9
N-V 180 180 270 40 180 14
N-VI 270 270 400 40 270 20
N-VII 400 400 600 40 400 30
N-VIII 550 550 600 40 550 41
N-IX 700 700 600 40 700 53
N-X 900 900 600 40 900 68
a
If the tool test is performed according to 4.1 (T2), the resistance value shall be achieved according to 4.1 (T2).
5 Technical documentation
5.1 The technical information shall be available for the testing laboratory when starting the testing
procedure.
Technical documentation shall contain the following information:
5.2 The date of issue and the name of the manufacturer or the name of the applicant requesting testing,
on each page.
5.3 Statement of the type of product: deposit safe or night safe and type of receiving unit (free-standing
or built-in receiving unit) together with a list of sizes covered by the same design.
The statement shall also give information about:
a) potential options (T2, EX and GAS),
b) whether a base to the deposit system is included or is an option,
c) the design capacity.
5.4 Drawings of the test specimen, including the system sub-units, showing the following:
The statement shall also give information about:
a) weight, outside and inside dimensions, and the manufacturing tolerances;
b) horizontal and vertical cross sections;
c) quantity, layout and features of locks, boltwork and relocking devices (system comprising blocking
and detecting elements which will prevent the boltwork from being withdrawn if a burglary attack
is detected. A relocking device can be part of the locking mechanism (e.g. active or live relocker) or
an independent unit (e.g. passive relocker));
d) quantity, pitch and position of door bolts, their dimensions (e.g. cross section), throw and
engagements and their type (moving or fixed);
e) location and design of any local areas of special protection material;
f) details of the fastening and/or fitting or anchoring of all elements relevant to physical security (e.g.
construction and position of joints and connections, the means by which the input unit, chute and
receiving unit are joined to each other);
g) marking, position and dimensions of any holes which pass through the protection material with a
detailed representation of specially protected areas;
h) details of optional features, e.g. time locking and time delay locking;
i) in case of a base this shall be identified.
5.5 List of all the locks that may be fitted, giving the manufacturer and model number.
5.6 Specification of the materials of construction if not contained on the drawings.
5.7 Details of any materials or device(s) intended to generate gas, smoke, soot, etc., in the event of
physical attack, or that could generate harmful substances during testing.
5.8 Statements of the nature and position of any cables and/or facilities for penetration detection
systems, for the mounting of electro-mechanical securing devices, alarm devices, etc.
5.9 Instructions for installation, giving at least the following details:
a) method by which the deposit system is anchored to the floor or other surface. If a base is included in
the deposit system the method by which the deposit system is anchored to the base and the base is
anchored to the floor or other surface;
b) for deposit systems with GAS designation the end user shall be informed of the parameters of the test
as: Gas testing is based on a receiving unit filled with 50 % gas in the test;
c) method of encasing built-in deposit systems, including:
1) the proportion of receiving unit to be encased;
2) the minimum size and section thickness of the encasement;
3) the minimum quality of encasement material; (the types and proportions of aggregates, cement
and other constituents; the flow ability of the freshly prepared mass and the 28-day cube
compression strength, together with methods of the test to measure these);
4) any reinforcement or anchoring to be included within the encasing mass.
5.10 For deposit systems that contain electric or electronic components, software, or pneumatically or
hydraulically controlled or driven components, the following information:
a) list of the assemblies used (type and supplier); motors, gearboxes, harnesses, PCBs (printed circuit
boards), etc.;
b) flow chart, state diagram or other description of the logica
...