SIST EN 13308:2003
(Main)Tanks for transport of dangerous goods - Service equipment for tanks - Non pressure balanced footvalve
Tanks for transport of dangerous goods - Service equipment for tanks - Non pressure balanced footvalve
This European Standard covers the non pressure balanced footvalve for bottom loading and unloading and specifies the performance requirements, dimensions and tests necessary to verify the compliance of the equipment to this standard.
Tanks für die Beförderung gefährlicher Güter - Bedienungsausrüstung von Tanks - Nichtdruckausgeglichenes Bodenventil
Diese Europäische Norm hat das nicht druckausgeglichene Bodenventil zum Beladen und Entladen zum Inhalt und legt die Kenndaten, Abmessungen und die Prüfverfahren fest, die notwendig sind, um die Übereinstimmung der Ausrüstung mit dieser Norm festzustellen.
Citernes de transport de matieres dangereuses - Equipement de service pour citernes - Clapets de fond a pression non compensée
La présente Norme européenne s'applique aux clapets de fond a pression non compensée et spécifie les exigences de performance, les dimensions et les essais nécessaires pour vérifier la conformité du dispositif a la présente norme.
L'équipement spécifié par la présente norme convient a une utilisation avec des produits pétroliers liquides et autres matieres dangereuses de la classe 3 de l'ADR - Accord européen relatif au transport international des marchandises dangereuses par route (liquides inflammables) dont la tension de vapeur ne dépasse pas 110 kPa a 50 °C - (y compris l'essence) - et qui n'appartiennent a aucune sous classification des produits toxiques ou corrosifs.
Cisterne za prevoz nevarnega blaga - Oprema za obratovanje cistern - Tlačno neizravnan spodnji ventil
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Tanks für die Beförderung gefährlicher Güter - Bedienungsausrüstung von Tanks - Nichtdruckausgeglichenes BodenventilCiternes de transport de matieres dangereuses - Equipement de service pour citernes - Clapets de fond a pression non compenséeTanks for transport of dangerous goods - Service equipment for tanks - Non pressure balanced footvalve23.060.20Zapirni ventili (kroglasti in pipe)Ball and plug valves23.020.20Posode in vsebniki, montirani na vozilaVessels and containers mounted on vehicles13.300Varstvo pred nevarnimi izdelkiProtection against dangerous goodsICS:Ta slovenski standard je istoveten z:EN 13308:2002SIST EN 13308:2003en01-december-2003SIST EN 13308:2003SLOVENSKI
STANDARD
SIST EN 13308:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13308November 2002ICS 13.300; 23.020.20; 23.060.20English versionTanks for transport of dangerous goods - Service equipment fortanks - Non pressure balanced footvalveCiternes de transport de matières dangereuses -Equipement de service pour citernes - Clapets de fond àpression non compenséeTanks für die Beförderung gefährlicher Güter -Bedienungsausrüstung von Tanks -Nichtdruckausgeglichenes BodenventilThis European Standard was approved by CEN on 22 August 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13308:2002 ESIST EN 13308:2003
EN 13308:2002 (E)2ContentspageForeword.3Introduction.41Scope.52Normative references.53Terms and definitions.54Functions.55Design characteristics.65.1Pressure rating.65.2Dimensions.65.3Mounting.65.4Bottom loading flow characteristics.65.5Actuation.65.6Break-away security.65.7Temperature range.75.8Materials of construction.75.9Electrical resistance.75.10Strainer.76Tests.76.1General.76.2Production tests.76.2.1General.76.2.2Shell tightness test.76.2.3Seat tightness test.86.2.4Operability test.86.2.5Test results.86.3Type tests.86.3.1General.86.3.2Shell strength test.86.3.3Shell tightness test.86.3.4Seat tightness test.96.3.5Operability test.96.3.6Mechanical Endurance test.96.3.7Break-away test.96.3.8Test results.107Marking.108Installation, operating and maintenance recommendations.10Annex A (normative)
Footvalve to tank mounting flange dimensions.11Annex B (normative)
Footvalve run-off flange dimensions.12Annex C (normative)
Footvalve run-off flange dimensions (square).13Annex D (normative)
Break-away test positions.14Annex E (informative)
Break-away test apparatus.15SIST EN 13308:2003
EN 13308:2002 (E)3ForewordThis document (EN 13308:2002) has been prepared by Technical Committee CEN /TC 296, "Tanks for transport ofdangerous goods", the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by May 2003, and conflicting national standards shall be withdrawn at the latest byMay 2003.This European Standard has been submitted for reference into the RID and/or in the technical annexes of the ADR.Therefore in this context the standards listed in the normative references and covering basic requirements of theRID/ADR not addressed within the present standard are normative only when the standards themselves arereferred to in the RID and/or in the technical annexes of the ADR.In this European Standard the annexes A, B, C and D are normative and the annex E is informative.This European Standard forms part of a coherent standards programme comprising the following standards:Tanks for transport of liquid dangerous goods with vapour pressure not exceeding 110 kPa (absolutepressure) at 50 °C and petrol - Service Equipment:EN 13081, Tanks for transport of dangerous goods - Service equipment for tanks - Vapour collection adaptor andcouplerEN 13082, Tanks for transport of dangerous goods - Service equipment for tanks - Vapour transfer valveEN 13083, Tanks for transport of dangerous goods - Service equipment for tanks - Adaptor for bottom loading andunloadingEN 13308, Tanks for transport of dangerous goods - Service equipment for tanks - Non-pressure balancedfootvalveEN 13314, Tanks for transport of dangerous goods - Service equipment for tanks - Fill hole coverEN 13315, Tanks for transport of dangerous goods - Service equipment for tanks - Gravity discharge couplerEN 13316, Tanks for transport of dangerous goods - Service equipment for tanks - Pressure balanced footvalveEN 13317, Tanks for transport of dangerous goods - Service equipment for tanks - Manhole cover assemblyWI 00296009, Tanks for transport of dangerous goods - Service equipment for tanks - Pressure and vacuumbreather ventWI 00296010, Tanks for transport of dangerous goods - Service equipment for tanks - Emergency pressure reliefvalveAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.SIST EN 13308:2003
EN 13308:2002 (E)4IntroductionThe non-pressure balanced footvalve, also called emergency valve or internal security valve, the subject of thisstandard, is an internal self closing stop valve ensuring the primary containment to confine the dangeroussubstances within the tank when closed.It allows the flow of dangerous substances in the unloading direction, that is, from the tank compartment into therun-off pipe only when externally actuated.The non-pressure balanced footvalve should be capable of allowing transfer of dangerous substances in thebottom loading direction through self-actuation by the hydraulic force of the loaded dangerous substances.SIST EN 13308:2003
EN 13308:2002 (E)51 ScopeThis European Standard is applicable to non pressure balanced footvalve and specifies the performancerequirements, critical dimensions and tests necessary to verify the compliance of the equipment with this standard.The equipment specified by this standard is suitable for use with liquid petroleum products and other dangeroussubstances of Class 3 of ADR - European Agreement concerning the International Carriage of Dangerous Goodsby Road – (flammable liquids) which have a vapour pressure not exceeding 110 kPa at 50 °C and petrol, and whichhave no-sub-classification as toxic or corrosive.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate pla
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.