Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test

1.1.1   Probe assemblies included in scope
This part of IEC 61010 specifies safety requirements for hand-held and hand-manipulated probe assemblies of the types described below, and their related accessories. These probe assemblies are for direct electrical connection between a part and electrical test and measurement equipment. They may be fixed to the
equipment or be detachable accessories for the equipment.
a) Type A: low-voltage and high-voltage, non-attenuating probe assemblies. Non-attenuating probe assemblies that are RATED for direct connection to voltages exceeding 30 V r.m.s., 42,4 V peak, or 60 V d.c., but not exceeding 63 kV. They do not incorporate components which are intended to provide a voltage divider function or a signal conditioning function, but they may contain non-attenuating components such as
fuses (see Figure 1).
b) Type B: high-voltage attenuating or divider probe assemblies. Attenuating or divider probe assemblies that are RATED for direct connection to secondary voltages exceeding 1 kV r.m.s or 1,5 kV d.c. but not exceeding 63 kV r.m.s or d.c. The divider function may be carried out wholly within the probe assembely, or partly within the test or measurement equipment to be used with the probe assembly (see Figure 2).
c) Type C: low-voltage attenuating or divider probe assemblies. Attenuating or divider probe assemblies for direct connection to voltages not exceeding 1 kV r.m.s. or 1,5 kV d.c. The signal conditioning function may be carried out wholly within the probe assembly, or partly within the test or measurement equipment intended to be used with the probe assembly (see Figure 3).
d) Type D: low-voltage attenuating, non-attenuating or other signal conditioning probe assemblies, that are RATED for direct connection only to voltages not exceeding 30 V r.m.s., or 42,4 V peak, or 60 V d.c., and are suitable for currents exceeding 8 A (see Figure 4).
1.1.2   Probe assemblies excluded from scope
This standard does not apply to current sensors within the scope of IEC 61010-2-032 (hand-held and hand-manipulated current sensors), but may apply to their input measuring circuit leads and accessories.

Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil 031: Sicherheitsbestimmungen für handgehaltenes Messzubehör zum elektrischen Messen und Prüfen

Exigences de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire - Partie 2-031: Exigences de sécurité pour sondes équipées tenues à la main pour mesurage et essais électriques

Varnostne zahteve za električno opremo za meritve, nadzorovanje in laboratorijsko uporabo - 031. del: Varnostne zahteve za ročne sonde za električne meritve in preskušanje

General Information

Status
Not Published
Public Enquiry End Date
28-May-2020
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
30-Mar-2020
Due Date
17-Aug-2020
Completion Date
24-Apr-2020

RELATIONS

Buy Standard

Amendment
SIST EN 61010-031:2015/oprAA:2020
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 61010-031:2015/oprAA:2020
01-maj-2020

Varnostne zahteve za električno opremo za meritve, nadzorovanje in laboratorijsko

uporabo - 031. del: Varnostne zahteve za ročne sonde za električne meritve in
preskušanje

Safety requirements for electrical equipment for measurement, control and laboratory

use - Part 031: Safety requirements for hand-held probe assemblies for electrical

measurement and test

Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte - Teil

031: Sicherheitsbestimmungen für handgehaltenes Messzubehör zum elektrischen
Messen und Prüfen

Exigences de sécurité pour appareils électriques de mesurage, de régulation et de

laboratoire - Partie 2-031: Exigences de sécurité pour sondes équipées tenues à la main

pour mesurage et essais électriques
Ta slovenski standard je istoveten z: EN 61010-031:2015/prAA
ICS:
19.080 Električno in elektronsko Electrical and electronic
preskušanje testing
71.040.10 Kemijski laboratoriji. Chemical laboratories.
Laboratorijska oprema Laboratory equipment
SIST EN 61010-031:2015/oprAA:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 61010-031:2015/oprAA:2020
---------------------- Page: 2 ----------------------
SIST EN 61010-031:2015/oprAA:2020
EUROPEAN STANDARD DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
prAA
March 2020
ICS 19.080
English Version
Safety requirements for electrical equipment for measurement,
control and laboratory use - Part 031: Safety requirements for
hand-held probe assemblies for electrical measurement and test

Exigences de sécurité pour appareils électriques de Sicherheitsbestimmungen für elektrische Mess-, Steuer-,

mesurage, de régulation et de laboratoire - Partie 2-031: Regel- und Laborgeräte - Teil 031:

Exigences de sécurité pour sondes équipées tenues à la Sicherheitsbestimmungen für handgehaltenes

main pour mesurage et essais électriques Messzubehör zum elektrischen Messen und Prüfen

This draft amendment prAA, if approved, will modify the European Standard ; it is submitted to CENELEC members for enquiry.

Deadline for CENELEC: 2020-06-05.
It has been drawn up by CLC/TC 66X.

If this draft becomes an amendment, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which

stipulate the conditions for giving this amendment the status of a national standard without any alteration.

This draft amendment was established by CENELEC in three official versions (English, French, German).

A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to

the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the

Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to

provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and

shall not be referred to as a European Standard.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Project: 70187 Ref. No. EN 61010-031:2015/prAA E
---------------------- Page: 3 ----------------------
SIST EN 61010-031:2015/oprAA:2020
EN 61010-031:2015/prAA:2020 (E)
European foreword

This document (EN 61010-031:2015/prAA:2020) has been prepared by CLC/TC 66X “Safety of

measuring, control, and laboratory equipment”.
This document is currently submitted to the Enquiry.
The following dates are proposed:
• latest date by which the existence of this (doa) dor + 6 months
document has to be announced at national
level
• latest date by which this document has to be (dop) dor + 12 months
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) dor + 36 months
conflicting with this document have to be (to be confirmed or
withdrawn modified when voting)
This document amends EN 61010-031:2015/FprA1:2018.

This document has been prepared under a mandate given to CENELEC by the European Commission

and the European Free Trade Association, and supports essential requirements of EU Directive(s).

For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this

document.
---------------------- Page: 4 ----------------------
SIST EN 61010-031:2015/oprAA:2020
EN 61010-031:2015/prAA:2020 (E)
1 Modifications to subclause 6.5.2.5.1.1
Replace the second paragraph with the following note:

“NOTE 1 The manufacturer is supposed to take the expected life of the probe assembly into account when

selecting insulating materials.”
As a result of this, renumber the existing note
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.