Grain-oriented electrical steel strip and sheet delivered in the fully processed state

EN 10107 defines the steel grades of grain-oriented electrical strip and sheet in nominal thicknesses of 0,23 mm, 0,27 mm, 0,30 mm and 0,35 mm and specifies in particular, general requirements, magnetic properties, geometric characteristics and tolerances and technological characteristics, as well as inspection procedures. This European Standard applies to Goss textured grain-oriented electrical sheet and strip supplied in the final annealed condition in sheets or coils, and intended for the construction of magnetic circuits. The materials are grouped into two classes : a) conventional grain oriented material ; b) high permeability grain oriented material . They correspond to Clause C.22 of IEC 60404-1:2000.

Kornorientiertes Elektroband und -blech im schlussgeglühten Zustand

Dieses Dokument legt die Stahlsorten für kornorientiertes Elektroband und -blech in den  Nenndicken 0,23 mm, 0,27 mm, 0,30 mm und 0,35 mm fest und im Besonderen allgemeine Anforderungen, magnetische Eigenschaften, geometrische Eigenschaften und Grenzabmaße, technologische Eigenschaften sowie Prüfbe-dingungen.
Dieses Dokument gilt für kornorientiertes Elektroblech und -band mit Goss-Textur, das im schlussgeglühten Zustand in Form von Tafeln oder Rollen geliefert wird und für den Bau magnetischer Kreise bestimmt ist.
Die Erzeugnisse sind in zwei Klassen, nach IEC 60404-1:2000 Abschnitt C22, wie folgt unterteilt:
a)   konventionelle kornorientierte Erzeugnisse;
b)   kornorientierte Erzeugnisse mit hoher Permeabilität.

Bandes et tôles et magnétiques en acier à grains orientés livrées à l'état fini

La présente Norme européenne définit les nuances d’acier des bandes et tôles magnétiques à grains orientés d'épaisseur nominale 0,23 mm, 0,27 mm, 0,30 mm et 0,35 mm, et spécifie en particulier les prescriptions générales, les caractéristiques magnétiques, les caractéristiques et tolérances géométriques et les caractéristiques technologiques ainsi que les modalités de contrôle.
La présente Norme européenne s’applique aux bandes et tôles magnétiques en acier à grains orientés, à texture de Goss, livrées à l’état de recuit final en feuilles ou en bandes et destinées à la construction de circuits magnétiques.
Les matériaux sont groupés en deux classes :
a)   matériau à grains orientés, conventionnel ;
b)   matériau à grains orientés, à haute perméabilité.
Ils correspondent à l'Article C.22 de la CEI 60404-1:2000.

Orientirana elektropločevina in trakovi, dobavljeni v končnem žarjenem stanju

Standard EN 10107 določa vrste jekla za orientirano elektropločevino in trakove z nazivnimi debelinami 0,23 mm, 0,27 mm, 0,30 mm in 0,35 mm ter posebej določa splošne zahteve, magnetne lastnosti, geometrijske lastnosti in tolerance ter tehnološke lastnosti in postopke pregledovanja. Ta evropski standard velja za elektropločevino in trak s teksturo Goss, dobavljen v končnem žarjenem stanju v obliki pločevine ali tuljav, in je namenjen konstruiranju magnetnih krogov. Materiali so razvrščeni v dva razreda: a) konvencionalni orientirani material, b) orientirani material z visoko prepustnostjo. Ti materiali ustrezajo točki C.22 iz standarda IEC 60404-1: 2000.

General Information

Status
Withdrawn
Public Enquiry End Date
24-May-2012
Publication Date
14-May-2014
Withdrawal Date
19-Sep-2022
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
16-Sep-2022
Due Date
09-Oct-2022
Completion Date
20-Sep-2022

Relations

Buy Standard

Standard
EN 10107:2014
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kornorientiertes Elektroband und -blech im schlussgeglühten ZustandBandes et tôles et magnétiques en acier à grains orientés livrées à l'état finiGrain-oriented electrical steel strip and sheet delivered in the fully processed state77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10107:2014SIST EN 10107:2014en,fr,de01-julij-2014SIST EN 10107:2014SLOVENSKI
STANDARDSIST EN 10107:20051DGRPHãþD



SIST EN 10107:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10107
March 2014 ICS 77.140.50 Supersedes EN 10107:2005English Version
Grain-oriented electrical steel strip and sheet delivered in the fully processed state
Bandes et tôles magnétiques en acier à grains orientés livrées à l'état fini
Kornorientiertes Elektroband und -blech im schlussgeglühten Zustand This European Standard was approved by CEN on 6 February 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10107:2014 ESIST EN 10107:2014



EN 10107:2014 (E) 2 Contents Page
Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .5 4 Classification and designation .5 4.1 Classification .5 4.2 Designation .5 5 Information to be supplied by the purchaser .6 5.1 Mandatory information .6 5.2 Options .6 6 General requirements .7 6.1 Production process .7 6.2 Form of supply .7 6.3 Delivery condition .7 6.4 Surface condition.7 6.5 Suitability for cutting .7 7 Technical requirements .8 7.1 Magnetic properties .8 7.1.1 General .8 7.1.2 Magnetic polarization .8 7.1.3 Specific total loss .8 7.2 Geometric characteristics and tolerances . 10 7.2.1 Thickness . 10 7.2.2 Width . 11 7.2.3 Length . 11 7.2.4 Edge camber . 11 7.2.5 Flatness (wave factor) . 12 7.2.6 Residual curvature. 12 7.2.7 Burr height . 12 7.3 Technological characteristics . 12 7.3.1 Density . 12 7.3.2 Stacking factor . 12 7.3.3 Number of bends . 12 7.3.4 Internal stresses . 12 7.3.5 Insulation coating resistance . 12 8 Inspection and testing . 12 8.1 General . 12 8.2 Sampling . 13 8.3 Preparation of test specimens . 13 8.3.1 Magnetic properties . 13 8.3.2 Geometrical characteristics and tolerances . 13 8.3.3 Technological characteristics . 14 8.4 Test methods . 14 8.4.1 General . 14 8.4.2 Magnetic properties . 14 8.4.3 Geometrical characteristics and tolerances . 15 8.4.4 Technological characteristics . 15 8.5 Retests . 16 9 Marking, labelling and packaging . 16 10 Complaints . 16 Annex A (informative)
Maximum specific total loss at 60 Hz and 1,7 T . 17 Bibliography . 18 SIST EN 10107:2014



EN 10107:2014 (E) 3 Foreword This document (EN 10107:2014) has been prepared by Technical Committee ECISS/TC 108 “Steel sheet and strip for electrical applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2014 and conflicting national standards shall be withdrawn at the latest by September 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10107:2005. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 10107:2014



EN 10107:2014 (E) 4 1 Scope This European Standard defines the steel grades of grain-oriented electrical strip and sheet in nominal thicknesses of 0,23 mm, 0,27 mm, 0,30 mm and 0,35 mm and specifies in particular, general requirements, magnetic properties, geometric characteristics and tolerances and technological characteristics, as well as inspection procedures. This European Standard applies to Goss textured grain-oriented electrical strip and sheet supplied in the final annealed condition in sheets or coils, and intended for the construction of magnetic circuits. The materials are grouped into two classes: a) conventional grain oriented material; b) high permeability grain oriented material. They correspond to Clause C.22 of IEC 60404-1:2000. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel products EN 10027-1, Designation systems for steel — Part 1: Steel names EN 10027-2, Designation systems for steels — Part 2: Numerical system EN 10204, Metallic products — Types of inspection documents EN 10251, Magnetic materials — Methods of determination of the geometrical characteristics of electrical steel sheet and strip EN 10280, Magnetic materials — Methods of measurement of the magnetic properties of electrical sheet and strip by means of a single sheet tester EN 10282:2001, Magnetic materials — Method of test for the determination of surface insulation resistance of electrical sheet and strip EN 10342, Magnetic materials — Classification of surface insulations of electrical steel sheet, strip and laminations EN 60404-2, Magnetic materials — Part 2: Methods of measurement of the magnetic properties of electrical steel sheet and strip by means of an Epstein frame (IEC 60404-2) EN 60404-11:2013, Magnetic materials — Part 11: method of test for the determination of surface insulation resistance of magnetic sheet and strip EN 60404-13, Magnetic materials — Part 13: Methods of measurement of density, resistivity and stacking factor of electrical steel sheet and strip (IEC 60404-13) EN ISO 7799:2000, Metallic materials — Sheet and strip 3 mm thick or less — Reverse bend test (ISO 7799:1985) SIST EN 10107:2014



EN 10107:2014 (E) 5 IEC 60050-121:1998, International Electrotechnical Vocabulary — Chapter 121: Electromagnetism IEC 60050-221:1990, International Electrotechnical Vocabulary — Chapter 221: Magnetic materials and components IEC 60404-3, Magnetic materials — Part 3: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of a single sheet tester 3 Terms and definitions For the purposes of this document, the terms and definitions of the principal terms relating to magnetic properties given in IEC 60050-121:1998 and IEC 60050-221:1990 and the following apply. 3.1 edge camber greatest distance between a longitudinal edge of the sheet and the line joining the two extremities of the measured length of this edge 3.2 flatness property of a sheet or of a length of strip which is characterised by the wave factor i.e. by the relation of the height of the wave to its length 3.3 number of bends number of alternate bends possible before the appearance of the first crack in the base metal visible to the naked eye indicating the ductility of the material 3.4 internal stresses stresses which are characterised by a deviation in relation to the line of cutting 4 Classification and designation 4.1 Classification The steel grades covered by this European Standard are classified according to the value of maximum specific total loss in watts per kilogram and according to the nominal thickness of the material (0,23 mm; 0,27 mm; 0,30 mm; 0,35 mm). 4.2 Designation 4.2.1 For the steel grades covered by this European Standard, the steel names are allocated in accordance with EN 10027-1. The steel numbers are allocated in accordance with EN 10027-2. 4.2.2 The steel names comprise the following in the order given: a) capital letter M for electrical steel; b) a number of one hundred times the specified value of maximum specific total loss at 1,7 T and 50 Hz, in watts per kilogram corresponding to the nominal product thickness; c) one hundred times the nominal thickness of the product, in millimetres; d) the characteristic letter: — S for conventional grain oriented products; SIST EN 10107:2014



EN 10107:2014 (E) 6 — P for high permeability grain oriented products. EXAMPLE M140-30S for conventional grain oriented electrical steel strip or sheet with a maximum specific total loss of 1,40 W/kg at 1,7 T , 50 Hz and a nominal thickness of 0,30 mm, supplied in the fully processed state. 5 Information to be supplied by the purchaser 5.1 Mandatory information For material to comply adequately with the requirements of this standard, the purchaser shall include the following information in his enquiry or order: a) quantity; b) type of product (strip or sheet); c) number of this European Standard (EN 10107); d) steel name or number (see 4.2.1); e) dimensions of sheets or strips required (including any limitations on the external diameter of a coil) (see 6.2 and 7.2.2); f) limitations on the mass of a bundle of sheets or of a coil (see 6.2); g) residual curvature for coils (see 7.2.6); h) inspection procedure required including the nature of the related documents (see 8.1). 5.2 Options A number of options are specified in this standard and listed below. lf the purchaser does not indicate his wish to implement one of these options, the products shall be supplied in accordance with the basis specification of this standard (see 5.1). 1) permissibility of welds and its marking (see 6.2); 2) compatibility between fluid and coating (see 6.4); 3) plus tolerances for nominal width (see Table 3, footnote a); 4) requirement concerning residual curvature (see 7.2.6); 5) acceptance unit other than 3 t (see 8.1); 6) test temperature other than (23 ± 5) °C (see 8.4.1); 7) alternative method for determination of magnetic properties (see 8.4.2); 8) marking of the products (see Clause 9); 9) requirement concerning the minimum insulation coating resistance (see 7.3.5). SIST EN 10107:2014



EN 10107:2014 (E) 7 6 General requirements 6.1 Production process The production process of the steel and its chemical composition are left to the discretion of the manufacturer. 6.2 Form of supply The material is supplied in coils in the case of strip and bundles in the case of sheets. The mass of coils or bundles of sheets shall be agreed at the time of enquiry and order. The recommended value for the internal diameter of coils is approximately 508 mm. Strip shall be of constant width and wound in such a manner that the edges are superimposed in a regular manner and that the side faces of the coil are substantially flat. Coils shall be sufficiently tightly wound so that they do not collapse under their own weight. S
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.