SIST EN ISO 2580-1:2003

Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2002)

1.1 ISO 2580-1:2002 establishes a system of designation for acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials, which may be used as the basis for specifications.
1.2 The types of ABS plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties
Vicat softening temperature
melt volume-flow rate
Charpy notched impact strength
tensile modulus
and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials.
1.3 This part of ISO 2580 is applicable to all acrylonitrile-butadiene-styrene materials consisting of a continuous phase based mainly on copolymers of styrene (and/or alkyl-substituted styrene) and acrylonitrile and a dispersed elastomeric phase based mainly on polybutadiene, plus other components, in such quantities as specified in the text.
It applies to ABS materials ready for normal use in the form of powder, granules, pellets or chips, unmodified or modified by colorants, additives, fillers, etc.
This part of ISO 2580 does not apply to materials
with a Charpy notched impact strength of less than 3 kilojoules per square metre;
containing less than 50 % by mass of butadiene in the elastomer of the elastomeric phase;
containing less than 15 % by mass of acrylonitrile in the continuous phase.

Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 2580-1:2002)

1.1   In diesem Teil von ISO 2580 wird ein Bezeichnungssystem für thermoplastische Acrylnitril-Butadien-Styrol (ABS)-Formmassen festgelegt, das als Grundlage für Spezifikationen dienen kann.
1.2   ABS-Formmasse-Typen werden mit Hilfe eines Einteilungssytems voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften:
a)   Vicat-Erweichungstemperatur,
b)   Schmelze-Volumenfließrate,
c)   Charpy-Kerbschlagzähigkeit,
d)   Zug-Modul
und auf Informationen über die Zusammensetzung, vorgesehene Anwendung und/oder Verarbeitungsverfahren, wichtige Eigenschaften, Additive, Farbstoffe, Füll- und Verstärkungsstoffe beruht.
1.3   Dieser Teil von ISO 2580 ist anwendbar auf alle Acrylnitril-Butadien-Styrol- und Acrylnitril-Formmassen mit einer kontinuierlichen Phase vorwiegend auf der Basis von Copolymeren des Styrols (und/oder alkylsubstituierten Styrols) und einer dispersen elastomeren Phase vorwiegend auf der Basis von Polybutadien, ohne oder mit Beimischung anderer neuer Komponenten in Mengen, wie im Daten-Block 1 festgelegt.
Er gilt für gebrauchsfertige ABS-Formmassen in Form von Pulver, Granulaten, Pellets oder Chips, nicht modifiziert oder modifiziert mit Farbstoffen, Additiven, Füllstoffen usw.
Dieser Teil von ISO 2580 ist nicht anwendbar für Materialien
   mit einer Charpy-Kerbschlagzähigkeit von weniger als 3 kJ/m2;
   mit einem Massenanteil von weniger als 50 % Butadien in Elastomeren der elastomeren Phase;
   mit einem Massenanteil von weniger als 15 % Acrylnitril in der kontinuierlichen Phase.
1.4   Es soll nicht unterstellt werden, dass Formmassen mit gleicher Bezeichnung notwendigerweise auch Gleiches leisten. Dieser Teil von ISO 2580 enthält keine technischen Daten, Leistungsangaben oder Verarbei-tungsbedingungen, die notwendig sein können, um eine Formmasse für eine spezielle Anwendung und/oder ein bestimmtes Verarbeitungsverfahren zu spezifizieren.
Wenn solche zusätzlichen Eigenschaften gefragt sind, sind sie, soweit möglich, mit Hil

Plastiques - Acrylonitrile-butadiene-styrene (ABS) pour moulage et extrusion - Partie 1: Systeme de désignation et base de spécifications (ISO 2580-1:2002)

L'ISO 2580-1:2002 établit un système de désignation des matériaux thermoplastiques acrylonitrile-butadiène-styrène (ABS) qui peut être utilisé comme base pour les spécifications.
Les types de plastiques ABS sont différenciés les uns des autres par un système de classification fondé sur des niveaux appropriés des propriétés de désignation
température de ramollissement Vicat
indice de fluidité à chaud en volume
résistance au choc Charpy
module de traction
et sur des informations concernant la composition, l'application prévue et /ou la méthode de mise en oeuvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renfort.
L'ISO 2580-1:2002 est applicable à tous les matériaux acrylonitrile-butadiène-styrène composés d'une phase continue basée principalement sur des copolymères de styrène (et/ou styrène substitué par des groupements alkyles) et d'acrylonitrile et d'une phase élastomérique dispersée principalement basée sur du polybutadiène avec d'autres composants dans les quantités spécifiées dans le texte.
Elle s'applique aux matériaux ABS prêts à une utilisation normale sous la forme de poudre, de grains, de granulés ou de copeaux, non modifiés ou modifiés par des colorants, des additifs ou des charges, etc.
L'ISO 2580-1:2002 ne s'applique pas aux matériaux
ayant une résistance au choc Charpy inférieure à 3 kilojoules par mètre carré;
contenant moins de 50 % en masse de butadiène dans l'élastomère de la phase élastomérique;
contenant moins de 15 % en masse d'acrylonitrile dans la phase continue.

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje na osnovi akrilonitril-butadien-stirena (ABS) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 2580-1:2002)

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-2003
• Withdrawal Date: 15-Dec-2015
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 16-Dec-2015
• Due Date: 08-Jan-2016
• Completion Date: 16-Dec-2015
• Ref Project: EN ISO 2580-1:2002 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2002)

Relations

• Replaced By: SIST EN ISO 19062-1:2016 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19062-1:2015)
• Effective Date: 01-Feb-2016
• Replaced By: SIST EN ISO 19062-1:2016 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19062-1:2015)
• Effective Date: 08-Jun-2022
• Replaces: SIST EN ISO 2580-1:2001 - Plastics - Acrylonitrile/butadiene/styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2000)
• Effective Date: 01-May-2003

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 2580-1:2003
01-maj-2003
1DGRPHãþD
SIST EN ISO 2580-1:2001
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHQDRVQRYLDNULORQLWULO
EXWDGLHQVWLUHQD$%6GHO6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH
,62
Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part
1: Designation system and basis for specifications (ISO 2580-1:2002)
Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen - Teil 1:
Bezeichnungssystem und Basis für Spezifikationen (ISO 2580-1:2002)
Plastiques - Acrylonitrile-butadiene-styrene (ABS) pour moulage et extrusion - Partie 1:
Systeme de désignation et base de spécifications (ISO 2580-1:2002)
Ta slovenski standard je istoveten z: EN ISO 2580-1:2002
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 2580-1:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2580-1:2003

---------------------- Page: 2 ----------------------

SIST EN ISO 2580-1:2003
EUROPEAN STANDARD
EN ISO 2580-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2002
ICS 83.080.20 Supersedes EN ISO 2580-1:2000
English version
Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and
extrusion materials - Part 1: Designation system and basis for
specifications (ISO 2580-1:2002)
Plastiques - Acrylonitrile-butadiène-styrène (ABS) pour Kunststoffe - Acrylnitril-Butadien-Styrol (ABS)-Formmassen
moulage et extrusion - Partie 1: Système de désignation et - Teil 1: Bezeichnungssystem und Basis für Spezifikationen
base de spécifications (ISO 2580-1:2002) (ISO 2580-1:2002)
This European Standard was approved by CEN on 25 August 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2580-1:2002 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 2580-1:2003
EN ISO 2580-1:2002 (E)
CORRECTED 2002-11-13
Foreword
This document (EN ISO 2580-1:2002) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by April 2003, and conflicting national
standards shall be withdrawn at the latest by April 2003.
This document supersedes EN ISO 2580-1:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 2580-1:2002 has been approved by CEN as EN ISO 2580-1:2002 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 2580-1:2003
EN ISO 2580-1:2002 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN/HD Year
ISO 1043-1 2001 Plastics - Symbols and abbreviated terms - EN ISO 1043-1 2001
Part 1: Basic polymers and their special
characteristics
ISO 2580-2 1994 Plastics - Acrylonitrile/butadiene/styrene EN ISO 2580-2 1999
(ABS) moulding and extrusion materials -
Part 2: Preparation of test specimen
3

---------------------- Page: 5 ----------------------

SIST EN ISO 2580-1:2003

---------------------- Page: 6 ----------------------

SIST EN ISO 2580-1:2003


INTERNATIONAL ISO
STANDARD 2580-1
Fifth edition
2002-10-01


Plastics — Acrylonitrile-butadiene-styrene
(ABS) moulding and extrusion materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Acrylonitrile-butadiène-styrène (ABS) pour moulage et
extrusion —
Partie 1: Système de désignation et base de spécifications




Reference number
ISO 2580-1:2002(E)
©
 ISO 2002

---------------------- Page: 7 ----------------------

SIST EN ISO 2580-1:2003
ISO 2580-1:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland

ii © ISO 2002 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 2580-1:2003
ISO 2580-1:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 2580 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2580-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
This fifth edition cancels and replaces the fourth edition (ISO 2580-1:2000), which has been technically revised.
ISO 2580 consists of the following parts, under the general title Plastics — Acrylonitrile-butadiene-styrene (ABS)
moulding and extrusion materials:
— Part 1: Designation system and basis for specifications
— Part 2: Preparation of test specimens and determination of properties

© ISO 2002 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 2580-1:2003

---------------------- Page: 10 ----------------------

SIST EN ISO 2580-1:2003
INTERNATIONAL STANDARD ISO 2580-1:2002(E)

Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and
extrusion materials —
Part 1:
Designation system and basis for specifications
1 Scope
1.1 This part of ISO 2580 establishes a system of designation for acrylonitrile-butadiene-styrene (ABS) moulding
and extrusion materials, which may be used as the basis for specifications.
1.2 The types of ABS plastic are differentiated from each other by a classification system based on appropriate
levels of the designatory properties
a) Vicat softening temperature
b) melt volume-flow rate
c) Charpy notched impact strength
d) tensile modulus
and on information about composition, intended application and/or method of processing, important properties,
additives, colorants, fillers and reinforcing materials.
1.3 This part of ISO 2580 is applicable to all acrylonitrile-butadiene-styrene materials consisting of a continuous
phase based mainly on copolymers of styrene (and/or alkyl-substituted styrene) and acrylonitrile and a dispersed
elastomeric phase based mainly on polybutadiene, plus other components, in such quantities as specified in the
text.
It applies to ABS materials ready for normal use in the form of powder, granules, pellets or chips, unmodified or
modified by colorants, additives, fillers, etc.
This part of ISO 2580 does not apply to materials
a) with a Charpy notched impact strength of less than 3 kilojoules per square metre;
b) containing less than 50 % by mass of butadiene in the elastomer of the elastomeric phase;
c) containing less than 15 % by mass of acrylonitrile in the continuous phase.
1.4 It is not intended to imply that materials having the same designation g
...