SIST EN 1074-6:2004
(Main)Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 6: Hydrants
Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 6: Hydrants
This European Standard defines the minimum fitness for purpose requirements for hydrants to be used in, or connected to, water supply pipe systems, above or below ground (see EN 805), carrying water intended for human consumption.
This standard specifies the design requirements, the performance requirements, and the conformity assessment method for hydrants, whatever their type, materials and functions. Where hydrants can be used for fire fighting, irrigation or other function, additional requirements can be given in other standards (e.g. prEN 14339:2001).
This standard applies in priority to any other product or test standard. The requirements from other standards apply only when this European Standard refers to them.
This part of EN 1074 deals with the requirements applicable to both underground and pillar hydrants, in sizes DN 65 to DN 150, and PFA up to 16 bar.
This part of EN 1074 does not give requirements for the outlets or their interface with the hydrants, since they are subject to national standards.
Armaturen für die Wasserversorgung - Anforderungen an die Gebrauchstauglichkeit und deren Prüfung - Teil 6: Hydranten
Robinetterie pour l'alimentation en eau - Prescriptions d'aptitude a l'emploi et vérifications s'y rapportant - Partie 6 : Poteaux et bouches
Cette partie 6 fixe les spécifications et contrôles applicables aux poteaux et bouches de pression nominale PN 10 - PN 16 et dont les diametres nominaux sont ceux définis dans la partie 1, limités au DN 150, il s'agit du diametre nominal de raccordement a la canalisation. Les essais de Type doivent etre réalisés sur tous les DN pour les poteaux et bouches. Par ailleurs, si une robinetterie de sectionnement est associée a ces appareils, pour une telle configuration, la partie 2 de la présente norme s'applique.
Ventili za vodooskrbo - Zahteve za ustreznost in ustrezni preskusi - 6. del: Hidranti
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ventili za vodooskrbo - Zahteve za ustreznost in ustrezni preskusi - 6. del: HidrantiArmaturen für die Wasserversorgung - Anforderungen an die Gebrauchstauglichkeit und deren Prüfung - Teil 6: HydrantenRobinetterie pour l'alimentation en eau - Prescriptions d'aptitude a l'emploi et vérifications s'y rapportant - Partie 6 : Poteaux et bouchesValves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 6: Hydrants91.140.60Sistemi za oskrbo z vodoWater supply systems23.060.99Drugi ventiliOther valvesICS:Ta slovenski standard je istoveten z:EN 1074-6:2004SIST EN 1074-6:2004en01-junij-2004SIST EN 1074-6:2004SLOVENSKI
STANDARD
SIST EN 1074-6:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1074-6January 2004ICS 23.060.99English versionValves for water supply - Fitness for purpose requirements andappropriate verification tests - Part 6: HydrantsRobinetterie pour l'alimentation en eau - Prescriptionsd'aptitude à l'emploi et vérifications s'y rapportant - Partie 6: Poteaux et bouchesArmaturen für die Wasserversorgung - Anforderungen andie Gebrauchstauglichkeit und deren Prüfung - Teil 6:HydrantenThis European Standard was approved by CEN on 3 November 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1074-6:2004: ESIST EN 1074-6:2004
EN 1074-6:2004 (E)2ContentspageForeword.4Introduction.51Scope.62Normative references.63Terms and definitions.74Design requirements.75Performance requirements.85.1Mechanical strength.85.1.1Resistance to internal pressure of the shell and of all pressure containing components.85.1.2Resistance of the obturator to differential pressure.85.1.3Resistance of hydrants to bending and to any force applied above the ground level.85.1.4Resistance of hydrants to operating loads.95.2Leak-tightness.95.2.1Leak-tightness of the shell and of all pressure containing components.95.2.2Seat tightness.95.2.3Maximum operating torque (MOT) for operation and seat-tightness.105.2.4Leak-tightness of gearboxes to external pressure.105.3Hydraulic characteristic.105.4Resistance to disinfection products.105.5Endurance.105.5.1Endurance of the hydrant.105.5.2Endurance of the non-return device.105.6Performance of the draining system.116Conformity assessment.116.1General.116.2Type tests.116.3Control of production process and quality system.117Marking.118Packaging.11Annex A (normative)
Test method for the resistance of hydrants to bending.13A.1General.13A.2Test procedure.13Annex B (normative)
Test method for the resistance of pillar hydrants to a force applied aboveground level.14B.1General.14B.2Test procedure for pillar hydrants not equipped with a breaking system.14B.3Test procedure for pillar hydrants equipped with a breaking system.15Annex C (normative)
Test method for the operation of hydrants.16C.1General.16C.2Test procedure.16Annex D (normative)
Test method for the endurance of hydrants.17D.1General.17D.2Test procedure.17SIST EN 1074-6:2004
EN 1074-6:2004 (E)3Annex E (normative)
Test method for the performance of draining system.18E.1General.18E.2Test procedure.18Bibliography.19SIST EN 1074-6:2004
EN 1074-6:2004 (E)4ForewordThis document (EN 1074-6:2004) has been prepared by Technical Committee CEN/TC 69 “Industrial valves”,the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by July 2004, and conflicting national standards shall be withdrawn at thelatest by July 2004.EN 1074 consists of six parts:¾ Part 1: General requirements;¾ Part 2: Isolating valves;¾ Part 3: Check valves;¾ Part 4: Air valves;¾ Part 5: Control valves;¾ Part 6: Hydrants.Part 1, in conjunction with the subsequent parts, lays down the general requirements and test procedures tobe carried out in production and during the assessment of conformity of these valves (type tests). The detailedrequirements, which depend on the types of valves, are defined in parts 2 to 6 of this European Standard.The annexes A, B, C, D and E of this European Standard are normative.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerlandand United Kingdom.SIST EN 1074-6:2004
EN 1074-6:2004 (E)5IntroductionIn respect of potential adverse effects on the quality of water intended for human consumption caused by theproduct covered by this European Standard:1) this European Standard provides no information as to whether the product can be used without restrictionin any of the Member States of the EU or EFTA;2) it should be noted that, while awaiting the adoption of verifiable European criteria, existing nationalregulations concerning the use and/or the characteristics of this product remain in force.SIST EN 1074-6:2004
EN 1074-6:2004 (E)61 ScopeThis European Standard defines the minimum fitness for purpose requirements for hydrants to be used in, orconnected to, water supply pipe systems, above or below ground (see EN 805), carrying water intended forhuman consumption.This standard specifies the design requirements, the performance requirements, and the conformityassessment method for hydrants, whatever their type, materials and functions. Where hydrants can be usedfor fire fighting, irrigation or other function, additional requirements can be given in other standards (e.g.prEN 14339:2001).This standard applies in priority to any other product or test standard. The requirements from other standardsapply only when this European Standard refers to them.This part of EN 1074 deals with the requirements applicable to both underground and pillar hydrants, in sizesDN 65 to DN 150, and PFA up to 16 bar.This part of EN 1074 does not give requirements for the outlets or their interface with the hydrants, since theyare subject to national standards.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications.These normative references are cited at the appropriate places in the text, and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publications apply tothis European Standard only when incorporated in it by amendment or revision. For undated references thelatest edition of the publication referred to applies (including amendments).EN 558-1, Industrial valves – Face-to-face and centre-to-face dimensions of metal valves for use in flangedpipe systems – Part 1: PN-designated valves.EN 1074-1:2000, Valves for water supply - Fitness for purpose requirements and appropriate verification tests- Part 1: General requirements.EN 1074-2:2000, Valves for water supply - Fitness for purpose requirements and appropriate verification tests– Part 2: Isolating valves.EN 1074-3:2000, Valves for water supply - Fitness for purpose requirements and appropriate verification tests– Part 3: Check valves.EN 1092-2, Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PNdesignated - Part 2: Cast iron flangesEN 1267:1999, Valves – Test of flow resistance using water as test fluid.EN 12266-1:2003, Industrial valves – Testing of valves – Part 1: Pressure tests, test procedures andacceptance criteria – Mandatory requirements.SIST EN 1074-6:2004
EN 1074-6:2004 (E)73 Terms and definitionsFor the purposes of this European Standard, the terms and definitions given in EN 1074-1 and the followingapply.3.1hydrantconnection to a water supply system including an isolating valve3.2pillar hydranthydrant with a connection point located above ground level, for use by water utilities or to supply water to firefighting equipment3.3breakable pillar hydrantpillar hydrant equipped with a specific device allowing its above ground part to separate from its below groundpart, when submitted to an impact3.4underground hydranthydrant with a connection point located under ground level, for use by water utilities or to supply water to firefighting equipment3.5theoretical ground levellimit between the above ground part and the underground part of the pillar hydrant as installedNOTEThis point is used for pillar positioning on site, once the height of components of the above ground part, thedepth of water supply pipeline axis and of the unfreezing device are defined.4 Design requirementsHydrants shall be designed in accordance with the design requirements given in clause 4 of EN 1074-1:2000,with the following additional or different requirements.The requirements of EN 558-1 (interchangeability) shall not apply to hydrants. When fitted with an inlet flange,it shall be in accordance with EN 1092-2. The outlets shall be in accordance with the national requirements.For hydrants manually operated, the closing direction shall be clockwise.If fitted, the breaking system shall be above the ground level and shall be replaceable in-situ.The manufacturer shall indicate in his technical documentation whether the hydrant is equipped with anautomatic draining device. If fitted, such a device shall comply with the National Health and SafetyRegulations.The manufacturer's technical documentation shall indicate whether the hydrant is equipped with a non-returndevice.SIST EN 1074-6:2004
EN 1074-6:2004 (E)85 Performance requirements5.1 Mechanical strength5.1.1 Resistance to internal pressure of the shell and of all pressure containing componentsRequirement and test shall be in accordance with 5.1.1 of EN 1074-1:2000, except that leakage of anautomatic draining device at a pressure less than 1 bar shall not be a reason for failure.To conduct this test the outlets of the hydrant and a drilled drain
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.