oSIST prEN ISO 6076:2022
(Main)Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles - Specification of trowel notch sizes (ISO/DIS 6076:2022)
Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles - Specification of trowel notch sizes (ISO/DIS 6076:2022)
This International Standard specifies the individual measurements of notches and assigns specific codes which may then be used to label notched tools complying with the measurements and tolerances specified in this standard.
Klebstoffe - Einbau von Bodenbelägen, Holzböden, Spachtelmassen und Fliesen - Festlegung von Zahnspachtelgrößen (ISO/DIS 6076:2022)
Adhésifs - Pose de revêtements de sol, planchers en bois, ragréages et carrelages - Spécifications des tailles des crans des peignes et spatules (ISO/DIS 6076:2022)
Lepila - Polaganje talnih oblog, lesenih talnih oblog, izravnalnih mas in ploščic - Specifikacija velikosti zobatih plazen (ISO/DIS 6076:2022)
General Information
Standards Content (sample)
SLOVENSKI STANDARD
oSIST prEN ISO 6076:2022
01-april-2022
Lepila - Polaganje talnih oblog, lesenih talnih oblog, izravnalnih mas in ploščic -
Specifikacija velikosti zobatih plazen (ISO/DIS 6076:2022)Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles -
Specification of trowel notch sizes (ISO/DIS 6076:2022)Klebstoffe - Einbau von Bodenbelägen, Holzböden, Spachtelmassen und Fliesen -
Festlegung von Zahnspachtelgrößen (ISO/DIS 6076:2022)
Adhésifs - Pose de revêtements de sol, planchers en bois, ragréages et carrelages -
Spécifications des tailles des crans des peignes et spatules (ISO/DIS 6076:2022)Ta slovenski standard je istoveten z: prEN ISO 6076
ICS:
83.180 Lepila Adhesives
oSIST prEN ISO 6076:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------oSIST prEN ISO 6076:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 6076:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 6076
ISO/TC 61/SC 11 Secretariat: JISC
Voting begins on: Voting terminates on:
2022-01-31 2022-04-25
Adhesives — Installation of floor coverings, wood flooring,
levelling compounds and tiles — Specification of trowel
notch sizes
ICS: 83.180
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 6076:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 6076:2022
ISO/DIS 6076:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 6076:2022
ISO/DIS 6076:2022(E)
Contents Page
Foreword ........................................................................................................................................................................................................................................iv
Introduction .................................................................................................................................................................................................................................v
1 Scope .................................................................................................................................................................................................................................1
2 Normative references .....................................................................................................................................................................................1
3 Terms and definitions ....................................................................................................................................................................................1
4 Shapes .............................................................................................................................................................................................................................. 2
5 Tolerances ................................................................................................................................................................................................................... 3
6 Material.......................................................................................................................................................................................................................... 3
7 Labelling ....................................................................................................................................................................................................................... 3
8 Trowel notch sizes – designations, dimensional specifications and illustrations ........................3
Annex A (informative) European and US notch designation ...................................................................................................... 9
Bibliography .............................................................................................................................................................................................................................11
iii© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 6076:2022
ISO/DIS 6076:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11 Products.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 6076:2022
ISO/DIS 6076:2022(E)
Introduction
For installation of floor coverings, wood flooring and ceramic tiles, adhesives, thin bed mortars and
similar products are spread (combed) onto the substrate commonly using grooved (notched) spatulas
or trowels. The notches of the respective trowels permit flow of the substance to be applied which will
then settle on the substrate in the form of strips (ridges). Consequently, the quantity of applied material
per unit area essentially depends on the geometry of the notches.© ISO 2022 – All rights reserved
---------------------- Page: 7 ----------------------
oSIST prEN ISO 6076:2022
---------------------- Page: 8 ----------------------
oSIST prEN ISO 6076:2022
DRAFT INTERNATIONAL STANDARD ISO/DIS 6076:2022(E)
Adhesives — Installation of floor coverings, wood flooring,
levelling compounds and tiles — Specification of trowel
notch sizes
1 Scope
This International Standard specifies the individual measurements of notches and assigns specific
codes which may then be used to label notched tools complying with the measurements and tolerances
specified in this standard.2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.