SIST EN ISO 19432:2008
(Main)Building construction machinery and equipment - Portable, hand-held, internal combustion engine driven cut-off machines - Safety requirements and testing (ISO 19432:2006)
Building construction machinery and equipment - Portable, hand-held, internal combustion engine driven cut-off machines - Safety requirements and testing (ISO 19432:2006)
This International Standard specifies safety requirements and their verification by testing for the design and construction of portable, hand-held, internal combustion engine driven, cut-off machines, intended to be used by a single operator in the cutting of construction materials, such as asphalt, concrete, stone and metal. It is applicable to those machines designed purposely for use with a rotating, bonded-abrasive and/or superabrasive (diamond) cut-off wheel having a maximum outside diameter of 406 mm, centre-mounted on, and driven by, a spindle shaft, where the top of the wheel rotates away from the operator (see Figure 1). This International Standard deals with all significant hazards related to the hand-held use of such machines (see Clause 4). It specifies methods for the elimination or reduction of hazards arising from their use, as well as the type of information on safe working practices to be provided with the machines. Cut-off machines designed in accordance with this International Standard are intended to be used by persons who have read and understood the safety requirements given in the "instruction handbook" and who use the appropriate personal protective equipment (PPE). Except for noise, environmental aspects are not considered by this International Standard; nor are cut-off wheel specifications given - for such specifications, see, for example, EN 12413 [1] and EN 13236 [2].
Baumaschinen und -ausrüstungen - Tragbare, handgeführte Trennschleifmaschinen mit Verbrennungsmotor - Sicherheit und Prüfverfahren (ISO 19432:2006)
Diese Internationale Norm legt Sicherheitsanforderungen und die Prüfung auf deren Einhaltung hinsichtlich der konstruktiven Gestaltung und des konstruktiven Aufbaus von tragbaren, handgeführten Trennschleifma-schinen mit eingebautem Verbrennungsmotor für Einmannbetrieb fest, die zum Schneiden von Baumaterialien, wie z. B. Asphalt, Beton, Stein und Metall, bestimmt sind. Sie gilt für solche Trennschleifmaschinen, die be¬stimmungsgemäß für den Einsatz mit einer rotierenden Trennschleifscheibe mit einem maximalen Durch¬messer von 406 mm und mit Trennschleifkörpern aus gebundenen Schleifmitteln und/oder Schleifwerkzeugen mit Diamant- und CBN-Schleifmitteln vorgesehen sind, die mittig auf einer Spindelwelle montiert sind und von dieser angetrieben werden, wobei sich die Stirnseite der Trennschleifscheibe in einer vom Anwender abge¬wandten Richtung dreht (siehe Bild 1).
Diese Internationale Norm behandelt alle signifikanten Gefahren, die mit dem handgeführten Einsatz derar-tiger Maschinen verbunden sind (siehe Abschnitt 4). Sie legt Verfahren für die Beseitigung oder Verminderung von Gefährdungen, die sich aus deren Anwendung ergeben, sowie die Art von Informationen über sichere Arbeitsabläufe fest, die mit der Maschine bereitzustellen sind. Die nach dieser Internationalen Norm gestal¬teten Trennschleifmaschinen sind für den Einsatz durch Personen bestimmt, die die in der „Betriebsanlei¬tung“ angegebenen Sicherheitsanforderungen gelesen und verstanden haben und die entsprechende persön¬liche Schutzausrüstung (PSA) verwenden.
Umweltaspekte, ausgenommen Beeinträchtigungen durch Geräusch, werden in dieser Internationalen Norm nicht behandelt, und es werden auch keine Spezifikationen für Trennschleifscheiben angegeben – siehe hier-zu z. B. EN 12413 [1] und EN 13236 [2].
Diese Internationale Norm gilt nicht für Maschinen, die vor dem Veröffentlichungsdatum dieses Dokuments hergestellt wurden.
Machines et matériels pour la construction des bâtiments - Tronçonneuses à disque, portatives, à moteur à combustion interne - Exigences de sécurité et essais (ISO 19432:2006)
L'ISO 19432:2006 spécifie les exigences de sécurité, et leur vérification par des essais, pour la conception et la fabrication de tronçonneuses à disque, portatives, à moteur à combustion interne, conçues uniquement pour être utilisées par un seul opérateur, pour couper des matériaux de construction, tels que l'asphalte, le béton, les pierres et le métal. Elle s'applique aux tronçonneuses spécifiquement conçues pour l'utilisation de meules à tronçonner, composées de particules abrasives liées et de particules de diamant et CBN, d'un diamètre maximal de 406 mm, dont la partie supérieure tourne loin de l'opérateur et qui présentent un montage central sur axe et sont entraînées par cet axe.
Stroji in oprema za graditev objektov - Prenosni ročni rezalniki z motorjem z notranjim zgorevanjem - Varnostne zahteve in preskušanje (ISO 19432:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 19432:2008
01-julij-2008
1DGRPHãþD
SIST EN ISO 19432:2006
6WURMLLQRSUHPD]DJUDGLWHYREMHNWRY3UHQRVQLURþQLUH]DOQLNL]PRWRUMHP]
QRWUDQMLP]JRUHYDQMHP9DUQRVWQH]DKWHYHLQSUHVNXãDQMH ,62
Building construction machinery and equipment - Portable, hand-held, internal
combustion engine driven cut-off machines - Safety requirements and testing (ISO
19432:2006)
Baumaschinen und -ausrüstungen - Tragbare, handgeführte Trennschleifmaschinen mit
Verbrennungsmotor - Sicherheit und Prüfverfahren (ISO 19432:2006)
Machines et matériels pour la construction des bâtiments - Tronçonneuses à disque,
portatives, à moteur à combustion interne - Exigences de sécurité et essais (ISO
19432:2006)
Ta slovenski standard je istoveten z: EN ISO 19432:2008
ICS:
91.220 Gradbena oprema Construction equipment
SIST EN ISO 19432:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 19432
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 91.220 Supersedes EN ISO 19432:2006
English Version
Building construction machinery and equipment - Portable,
hand-held, internal combustion engine driven cut-off machines -
Safety requirements and testing (ISO 19432:2006)
Machines et matériels pour la construction des bâtiments - Baumaschinen und -ausrüstungen - Tragbare,
Tronçonneuses à disque, portatives, à moteur à handgeführte Trennschleifmaschinen mit
combustion interne - Exigences de sécurité et essais (ISO Verbrennungsmotor - Sicherheit und Prüfverfahren (ISO
19432:2006) 19432:2006)
This European Standard was approved by CEN on 25 March 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19432:2008: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 19432:2008 (E)
Contents Page
Foreword.3
Annex ZA (informative) Relationship between this International Standard and the Essential
Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC .4
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .5
2
---------------------- Page: 3 ----------------------
EN ISO 19432:2008 (E)
Foreword
The text of ISO 19432:2006 has been prepared by Technical Committee ISO/TC 195 “Building construction
machinery and equipment” of the International Organization for Standardization (ISO) and has been taken
over as EN ISO 19432:2008 by Technical Committee CEN/TC 151 “Construction equipment and building
material machines - Safety” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at
the latest by October 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19432:2006.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directives, see informative Annex ZA and ZB, which are integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 19432:2006 has been approved by CEN as a EN ISO 19432:2008 without any modification.
3
---------------------- Page: 4 ----------------------
EN ISO 19432:2008 (E)
Annex ZA
(informative)
Relationship between this International Standard and the Essential
Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC
This International Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide one means of conforming to Essential Requirements of
the New Approach Directive Machinery Directive 98/37/EC, amended by Directive 98/79/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this International standard confers, within the limits of the scope of this standard, a presumption of
conformity with Essential Requirement 2.2 of that Directive and associated EFTA regulations.
WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling within the
scope of this International standard.
4
---------------------- Page: 5 ----------------------
EN ISO 19432:2008 (E)
Annex ZB
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 2006/42/EC on machinery.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the relevant Essential Requirements of that Directive except Essential Requirements 1.7.3 (additional
marking of business address and the designation of machines), 1.7.4.2 u) (uncertainty of noise measurement)
and 2.2.1.1 (uncertainty of vibration measurements), and associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.
5
---------------------- Page: 6 ----------------------
INTERNATIONAL ISO
STANDARD 19432
First edition
2006-03-15
Building construction machinery and
equipment — Portable, hand-held,
internal combustion engine driven cut-off
machines — Safety requirements and
testing
Machines et matériel pour la construction des bâtiments —
Tronçonneuses à disques, portatives, à moteur à combustion interne —
Exigences de sécurité et essais
Reference number
ISO 19432:2006(E)
©
ISO 2006
---------------------- Page: 7 ----------------------
ISO 19432:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 8 ----------------------
ISO 19432:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 List of significant hazards . 4
5 Safety requirements and verification. 5
5.1 General. 5
5.2 Handles . 6
5.3 Speed . 6
5.4 Engine stopping device. 7
5.5 Throttle control . 7
5.6 Clutch. 8
5.7 Exhaust gases. 8
5.8 Cutting debris discharge . 8
5.9 Tank openings. 9
5.10 Protection against contact with parts under high voltage . 9
5.11 Transmission cover(s). 9
5.12 Protection against contact with hot parts. 9
5.13 Cut-off wheel guard . 11
5.14 Flange locking device. 12
5.15 Flange assembly. 13
5.16 Spindle diameter. 14
5.17 Special tools. 14
5.18 Noise . 14
5.19 Vibration . 14
6 Information for use . 15
6.1 Instruction handbook . 15
6.2 Markings . 18
6.3 Warnings. 18
Annex A (normative) Strength test of cut-off wheel guard. 19
Annex B (normative) Noise test code — Engineering method (grade 2 of accuracy) . 21
Annex C (normative) Measurement of vibration values at the handles . 29
Annex D (informative) Recommended pictorials and symbols . 36
Bibliography . 37
© ISO 2006 – All rights reserved iii
---------------------- Page: 9 ----------------------
ISO 19432:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 19432 was prepared by Technical Committee ISO/TC 195, Building construction machinery and
equipment.
iv © ISO 2006 – All rights reserved
---------------------- Page: 10 ----------------------
ISO 19432:2006(E)
Introduction
The structure of safety standards in the field of machinery is as follows.
a) Type-A standards (basis standards) give basic concepts, principles for design, and general aspects that
can be applied to machinery.
b) Type-B standards (generic safety standards) deal with one or more safety aspect(s) or one or more
type(s) of safeguards that can be used across a wide range of machinery:
⎯ type-B1 standards on particular safety aspects (e.g. safety distances, surface temperature, noise);
⎯ type-B2 standards on safeguards (e.g. two-hands controls, interlocking devices, pressure-sensitive
devices, guards).
c) Type-C standards (machinery safety standards) deal with detailed safety requirements for a particular
machine or group of machines.
This International Standard is a type-C standard as stated in ISO 12100-1.
When provisions of this type-C standard are different from those which are stated in type-A or type-B
standards, the provisions of this type-C standard take precedence over the provisions of the other standards
for machines that have been designed and built according to the provisions of this type-C standard.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered as
indicated in the scope of this International Standard.
This International Standard is based on EN 1454:1998 and an ANSI draft.
© ISO 2006 – All rights reserved v
---------------------- Page: 11 ----------------------
INTERNATIONAL STANDARD ISO 19432:2006(E)
Building construction machinery and equipment — Portable,
hand-held, internal combustion engine driven cut-off
machines — Safety requirements and testing
1 Scope
This International Standard specifies safety requirements and their verification by testing for the design and
construction of portable, hand-held, internal combustion engine driven, cut-off machines, intended to be used
by a single operator in the cutting of construction materials, such as asphalt, concrete, stone and metal. It is
applicable to those machines designed purposely for use with a rotating, bonded-abrasive and/or
superabrasive (diamond) cut-off wheel having a maximum outside diameter of 406 mm, centre-mounted on,
and driven by, a spindle shaft, where the top of the wheel rotates away from the operator (see Figure 1).
This International Standard deals with all significant hazards related to the hand-held use of such machines
(see Clause 4). It specifies methods for the elimination or reduction of hazards arising from their use, as well
as the type of information on safe working practices to be provided with the machines. Cut-off machines
designed in accordance with this International Standard are intended to be used by persons who have read
and understood the safety requirements given in the “instruction handbook” and who use the appropriate
personal protective equipment (PPE).
Except for noise, environmental aspects are not considered by this International Standard; nor are cut-off
[1] [2]
wheel specifications given — for such specifications, see, for example, EN 12413 and EN 13236 .
This International Standard is not applicable to machines manufactured before the date of its publication.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3744:1994, Acoustics — Determination of sound power levels of noise sources using sound pressure —
Engineering method in an essentially free field over a reflecting plane
ISO 4871:1996, Acoustics — Declaration and verification of noise emission values of machinery and
equipment
ISO 5348:1998, Mechanical vibration and shock — Mechanical mounting of accelerometers
ISO 5349-2:2001, Mechanical vibration — Measurement and evaluation of human exposure to hand-
transmitted vibration — Part 2: Practical guidance for measurement at the workplace
ISO 7293:1997, Forestry machinery — Portable chain-saws — Engine performance and fuel consumption
ISO 7914:2002, Forestry machinery — Portable chain-saws — Minimum handle clearance and sizes
ISO 8041:1990, Human response to vibration — Measuring instrumentation
© ISO 2006 – All rights reserved 1
---------------------- Page: 12 ----------------------
ISO 19432:2006(E)
ISO 11201:1995, Acoustics — Noise emitted by machinery and equipment — Measurement of emission
sound pressure levels at a work station and at other specified positions — Engineering method in an
essentially free field over a reflecting plane
ISO/TR 11688-1:1995, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning
ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology
ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical
principles
ISO 13852:1996, Safety of machinery — Safety distances to prevent danger zones being reached by the
upper limbs
ISO 16063-1:1998, Methods for the calibration of vibration and shock transducers — Part 1: Basic concepts
IEC 60745-1:2003, Hand-held motor-operated electric tools — Safety — Part 1: General requirements
IEC 61672-1:2002, Electroacoustics — Sound level meters — Part 1: Specifications
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12100-1 and the following apply.
3.1
cut-off wheel
wheel composed of abrasive particles bonded together by an appropriate binder and incorporating, if
necessary, some appropriate form of reinforcement, or made of metal or other materials of similar properties
and having diamond, CBN-particles or other suitable abrasive particles bonded to its rim
3.2
arbor hole
centre hole of the cut-off wheel used for mounting the cut-off wheel on the machine spindle
3.3
blotter
washers made from some compressible material (e.g. paper, card or similar), attached to each side of the
cut-off wheel, the function of which is to smooth imperfections in the cut-off wheel and allow a limited degree
of slip when the wheel stalls in use
3.4
choke
device for enriching the fuel air mixture in the carburettor, to aid starting
3.5
clutch
device for connecting and disconnecting the driven member to and from a rotating source of power
3.6
cut-off wheel guard
partial enclosure intended to deflect cutting debris, as well as pieces of the cut-off wheel in the event that the
wheel is broken in operation
3.7
engine stopping device
device by which the stopping of the power source is initiated
2 © ISO 2006 – All rights reserved
---------------------- Page: 13 ----------------------
ISO 19432:2006(E)
3.8
flange contact surface
area between the inner and the outer circumference on the flange, which forms the contact surface between
the flange and the cut-off wheel
3.9
flange assembly
device provided to clamp and drive the cut-off wheel
3.10
handle
device designed to facilitate safe and easy control of the machine
3.10.1
front handle
handle located at or towards the front of the engine housing
3.10.2
rear handle
handle located at or towards the rear of the power source housing
3.11
idle speed
speed at which the engine runs with no load and throttle control released and the cut-off wheel does not rotate
3.12
reactive forces
sudden and unexpected motion of the machine, which can occur when the rotating cut-off wheel contacts a
foreign object during cutting or because of pinching
3.13
maximum depth of cut
t
distance to which the cut-off wheel can enter the work-piece as measured from the outside diameter of the
wheel to the outside diameter of the flange
3.14
maximum cut-off wheel speed
maximum permitted speed of a new cut-off wheel marked on the cut-off wheel
3.15
maximum spindle speed
maximum speed at which the spindle rotates with full open throttle and no load
3.16
silencer
device for reducing engine exhaust noise and directing the exhaust gases
3.17
rated speed
engine speed at which maximum power occurs
3.18
spindle
shaft of the cut-off machine, which supports, retains and drives the cut-off wheel in connection with the flanges
3.19
throttle control
device for controlling the engine speed
© ISO 2006 – All rights reserved 3
---------------------- Page: 14 ----------------------
ISO 19432:2006(E)
3.20
throttle lock
device for temporarily setting the throttle in a partially open position, to aid starting
3.21
throttle lock-out
device that prevents the unintentional operation of the throttle trigger until manually released
3.22
throttle control linkage
mechanism which transmits motion from the throttle control to the throttle control valve
3.23
transmission cover
device between the engine and the cutting equipment designed to prevent unintentional contact with the
transmission
4 List of significant hazards
This clause lists significant hazards, hazardous situations and events as far as they are dealt with in this
document, identified by risk assessment as significant for this type of machinery, and which require action to
eliminate or reduce the risk. See Table 1.
4 © ISO 2006 – All rights reserved
---------------------- Page: 15 ----------------------
ISO 19432:2006(E)
Table 1 — List of significant hazards
Clause(s) in this
No. Hazard International Standard
dealing with the hazard
1 Mechanical hazards due to cutting, impact and reactive forces (i.e. climbing, 5.2; 5.11; 5.13; 5.14; 5.15;
pulling and especially reactive forces) related to the cut-off wheel and the 5.16; 6.1.2
transmission to the cut-off wheel
2 Electrical hazards due to contact with parts under high voltage (direct contact) or 5.10
parts which have become under high voltage under faulty conditions (indirect
contact)
3 Thermal hazards resulting in burns, scalds and other injuries, by a possible contact 5.12
of persons with objects or materials with high temperature including the radiation of
heat sources
4 Noise, resulting in hearing losses (deafness) and other physiological disorders 5.18; 6.1; 6.3
(e.g. loss of balance; loss of awareness) and interference with auditory signals and
speech communication
5 Vibration (resulting in peripheral circulatory and nervous functional disturbances in 5.19; 6.1; 6.3
the hand-arm system, such as “white finger” disease)
6 Contact with or inhalation of harmful fluids, gases, mists and fumes related to 5.7.1; 5.8, 5.13.1; 6.1.2, 6.3
exhaust gases and dust related to debris of cut-off materials
7 Fire or explosion related to fuel spillage 5.9, 6.1.2
8 Neglecting of ergonomic principles in machine design such as hazards from 5.2; 5.5; 6.1.2; 6.3
unhealthy postures or excessive efforts and inadequate consideration of human
hand-arm anatomy related to handle design, machine balance
9 Unexpected start-up, unexpected overrun/over-speed from failure/disorder of the 5.2; 5.4; 5.5; 5.6;
control system related to failure in the handles and position of the controls
10 Impossibility of stopping the machine in the best possible conditions related to the 5.2; 5.4
handle strength and position of the engine stopping device
11 Failure of the control system related to handle strength, position of controls and 5.5; 6.3
marking
12 Brake up during operation related to cut-off wheel 5.3; 5.14; 6.1; 6.3
13 Ejection of objects related to debris 5.3; 5.8; 5.13, 6.1.2; 6.3
5 Safety requirements and verification
CAUTION — Some of the tests specified in this International Standard involve processes that could
lead to a hazardous situation. Any person performing tests in accordance with this International
Standard shall be appropriately trained in the type of work to be carried out. All national regulatory
conditions and health and safety requirements shall be followed.
5.1 General
The safe running of cut-off machines depends on both the safety requirements according to this clause and
the safe working conditions associated with the use of adequate personal protection equipment (PPE), such
as gloves, leg protection, boots, and eye, ear and head protection equipment (see Clause 6).
Cut-off machines shall comply with the safety requirements and/or protective measures of this clause. Cut-off
machines shall also be marked according to 6.2 and wear warnings according to 6.3. In addition, the machine
shall be designed according to the principles of ISO 12100-2 for hazards relevant but not significant, which are
not dealt with by this document.
© ISO 2006 – All rights reserved 5
---------------------- Page: 16 ----------------------
ISO 19432:2006(E)
When the machine is placed in its normal position on a flat horizontal surface (see Figure 1), the cut-off wheel
or the guard shall
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.