SIST-TS CEN/TS 15410:2007
(Main)Solid recovered fuels - Method for the determination of the content of major elements (Al, Ca, Fe, K, Mg, Na, P, Si, Ti)
Solid recovered fuels - Method for the determination of the content of major elements (Al, Ca, Fe, K, Mg, Na, P, Si, Ti)
This Technical Specification specifies three methods of digestion for solid recovered fuels:
a) microwave assisted digestion with hydrofluoric, nitric and hydrochloric acid mixture;
b) hot water bath digestion of with hydrofluoric, nitric and hydrochloric acid mixture, after ashing of the SRFs sample;
c) oven digestion with nitric, perchloric and hydrofluoric acid mixture.
Instrumental determination of Si, Al, K, Na, Ca, Mg, Fe, P, and Ti is performed by Inductively Coupled Plasma Spectrometry with optical detection or other suitable spectroscopic techniques such as Flame Atomic Spectroscopy.
The effectiveness of the digestion can be verified by qualitative X-ray fluorescence (XRF) analysis on the remaining residue. If necessary an alternative digestion method (among those proposed) needs to be used.
XRF can be used for the analysis of Si, Al, K, Na, Ca, Mg, Fe, P, Ti, after ashing (550 °C) of the sample: other elements can be analysed by XRF providing that the concentration levels are above the instrumental detection limits of the XRF instrumentation and after proper preliminary testing.
Method a) is recommended for general use, but the amount of the test portion can be very low in case of high concentration of organic matter. Method b) is recommended for SRFs with high organic matter concentration that can be difficult to digest with the other methods.
Method c) is recommended for SRFs samples for which the other methods leave a significant insoluble residue.
All the listed methods are suitable for the determination of Si, provided that closed containers are used for sample dissolution. XRF is highly recommended for Si, P and Ti analysis.
Feste Sekundärbrennstoffe - Verfahren zur Bestimmung des Gehaltes an Hauptelementen (Al, Ca, Fe, K, Mg, Na, P, Si, Ti)
Combustibles solides de récupération - Méthodes pour la détermination de la teneur en éléments majeurs (Al, Ca, Fe, K, Mg, Na, P, Si et Ti)
Trdno alternativno gorivo - Metoda za določevanje glavnih elementov (Al, Ca, Fe, K, Mg, Na, P, Si, Ti)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CEN/TS 15410:2007
01-marec-2007
7UGQRDOWHUQDWLYQRJRULYR0HWRGD]DGRORþHYDQMHJODYQLKHOHPHQWRY $O&D)H
.0J1D36L7L
Solid recovered fuels - Method for the determination of the content of major elements (Al,
Ca, Fe, K, Mg, Na, P, Si, Ti)
Feste Sekundärbrennstoffe - Verfahren zur Bestimmung des Gehaltes an
Hauptelementen (Al, Ca, Fe, K, Mg, Na, P, Si, Ti)
Combustibles solides de récupération - Méthodes pour la détermination de la teneur en
éléments majeurs (Al, Ca, Fe, K, Mg, Na, P, Si et Ti)
Ta slovenski standard je istoveten z: CEN/TS 15410:2006
ICS:
75.160.10 Trda goriva Solid fuels
SIST-TS CEN/TS 15410:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
TECHNICAL SPECIFICATION
CEN/TS 15410
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
September 2006
ICS 75.160.10
English Version
Solid recovered fuels - Method for the determination of the
content of major elements (Al, Ca, Fe, K, Mg, Na, P, Si, Ti)
Combustibles solides de récupération - Méthodes pour la Feste Sekundärbrennstoffe - Verfahren zur Bestimmung
détermination de la teneur en éléments majeurs (Al, Ca, des Gehaltes an Hauptelementen (Al, Ca, Fe, K, Mg, Na,
Fe, K, Mg, Na, P, Si et Ti) P, Si, Ti)
This Technical Specification (CEN/TS) was approved by CEN on 25 March 2006 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 15410:2006: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
CEN/TS 15410:2006 (E)
Contents Page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .6
4 Safety remarks .6
5 Principle.7
6 Apparatus .7
7 Reagents.8
8 Procedure .8
9 Digestion procedure.9
10 Analysis of the digestion solutions .9
11 Expression of results .10
12 Quality control.11
13 Performance characteristics .11
14 Test report .11
Annex A (normative) Guidelines - Characteristics of the laboratory sample for chemical analysis
of SRF .12
Bibliography .14
2
---------------------- Page: 3 ----------------------
CEN/TS 15410:2006 (E)
Foreword
This document (CEN/TS 15410:2006) has been prepared by Technical Committee CEN/TC 343 “Solid
Recovered Fuels”, the secretariat of which is held by SFS.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this CEN Technical Specification: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
3
---------------------- Page: 4 ----------------------
CEN/TS 15410:2006 (E)
Introduction
Accurate determination of trace element content in solid recovered fuels is important for environmental and
technical reasons both in the production and combustion stage. The determination of major elements such as
Al, Ca, Fe, Mg, P, K, Si, Na and Ti can be helpful to predict the melting behaviour and slagging of the ash.
After digestion of the solid recovered fuels using different methods, a number of analytical techniques can be
used for the quantification of the trace element content. They include Inductively Coupled Plasma with optical
or mass detection, Flame Atomic Spectroscopy, Graphite Furnace Atomic Absorption Spectrometry and X-ray
fluorescence spectrometry. X-ray fluorescence allows the simultaneous determination of these elements after
ashing of SRF. Direct analysis of the SRF material is not possible by XRF due to the sample inhomogeneity
and because suitable certified reference materials for calibration are not available.
4
---------------------- Page: 5 ----------------------
CEN/TS 15410:2006 (E)
1 Scope
This Technical Specification specifies three methods of digestion for solid recovered fuels:
a) microwave assisted digestion with hydrofluoric, nitric and hydrochloric acid mixture;
b) hot water bath digestion of with hydrofluoric, nitric and hydrochloric acid mixture, after ashing of the SRFs
sample;
c) oven digestion with nitric, perchloric and hydrofluoric acid mixture.
Instrumental determination of Si, Al, K, Na, Ca, Mg, Fe, P, and Ti is performed by Inductively Coupled Plasma
Spectrometry with optical detection or other suitable spectroscopic techniques such as Flame Atomic
Spectroscopy.
The effectiveness of the digestion can be verified by qualitative X-ray fluorescence (XRF) analysis on the
remaining residue. If necessary an alternative digestion method (among those proposed) shall be used.
XRF can be used for the analysis of Si, Al, K, Na, Ca, Mg, Fe, P, Ti, after ashing (550 °C) of the sample: other
elements can be analysed by XRF providing that the concentration levels are above the instrumental detection
limits of the XRF instrumentation and after proper preliminary testing.
Method a) is recommended for general use, but the amount of the test portion can be very low in case of high
concentration of organic matter. Method b) is recommended for SRFs with high organic matter concentration
that can be difficult to digest with the other methods.
Method c) is recommended for SRFs samples for which the other methods leave a significant insoluble
residue.
All the listed methods are suitable for the determination of Si, provided that closed containers are used for
sample dissolution. XRF is highly recommended for Si, P and Ti analysis.
2 Normative references
The following referenced documents are indispensable for the application of this Technical Specification. For
dated references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 13656, Characterization of waste — Microwave assisted digestion with hydrofluoric (HF), nitric (HNO )
3
and hydrochloric (HCI) acid mixture for subsequent determination of elements
CEN/TS 15357:2006, Solid recovered fuels — Terminology, definitions and descriptions
CEN/TS 15413, Solid recovered fuels — Methods for the preparation of the test sample from the laboratory
sample
prCEN/TS 15414-3, Solid recovered fuels — Determination of moisture content using the oven dry method —
Part 3: Moisture in general analysis sample
prCEN/TS 15403, Solid recovered fuels — Methods for the determination of ash content
EN ISO 3696:1995, Water for analytical laboratory use — Specification and test methods (ISO 3696:1987)
EN ISO 11885, Water quality — Determination of 33 elements by inductively coupled plasma atomic emission
spectroscopy (ISO 11885:1996)
5
---------------------- Page: 6 ----------------------
CEN/TS 15410:2006 (E)
EN ISO 12020, Water quality — Determination of aluminium — Atomic absorption spectrometric methods
(ISO 12020:1997)
EN ISO 15586, Water quality — Determination of trace elements using atomic absorption spectrometry with
graphite furnace (ISO 15586:2003)
ISO 9964-1, Water quality — Determination of sodium and potassium — Part 1: Determination of sodium by
atomic absorption spectrometry
ISO 9964-2, Water quality — Determination of sodium and potassium — Part 2: Determination of potassium
by atomic absorption spectrometry
ISO 9964-3, Water quality — Determination of sodium and potassium — Part 3: Determination of sodium and
potassium by flame emission spectrometry
3 Terms and definitions
For the purposes of this Technical Specification, the terms and definitions given in
CEN/TS 15357:2006 and the following apply.
3.1
digestion
mineralization of the organic matter of a sample and dissolution of its mineral part, more or less completely,
when reacted with a reagent mixture
3.2
microwave unit
whole microwave digestion system (oven and associated equipment)
4 Safety remarks
The safety in handling of potentially hazardous materials is dealt with in relevant national and European
regulations, which every laboratory should refer to.
In addition the following information is given:
only experienced personnel can use the microwave apparatus, following the operating instructions
described in the manufacturer’s manual;
most of the reagents used within this Technical Specification are strongly corrosive and toxic. Safety
precautions are absolutely necessary due to strong corrosive reagents, high temperature and high
pressure;
all procedures have to be performed in a hood or in closed force-ventilated equipment. By the use of
strong oxidising reagents the formation of explosive organic intermediates is possible especially when
dealing with samples with a high organic content. Do not open pressurised vessels before they have
cooled down. Avoid contact with the chemicals and the gaseous reaction products;
the X-ray fluorescence spectrometers on the market are generally approved fully protected apparatus.
This means that the user is not subjected to any radiation when operating the apparatus. All the
apparatus are subject to specific official approval and acceptance conditions;
the person responsible for managing or supervising the operation of X-ray equipment shall provide
evidence of his knowledge of radiation protection according to national regulations.
6
---------------------- Page: 7 ----------------------
CEN/TS 15410:2006 (E)
5 Principle
The test portion is digested using one of the proposed methods with a suitable acid mixture. The digested
sample is then analysed by inductively coupled plasma atomic emission spectroscopy.
For XRF analysis the sample is ashed at 550 °C and the ash is homogenised in a ball mill to obtain a uniform
size dimension of the particles. The ash is then pressed in the form of pellet or fused with tetraborate. Both
techniques are suitable for the analysis by XRF. Coal ash and other ashes of various origins can be used for
instrument calibration.
6 Apparatus
6.1 Microwave unit
Intended for laboratory use and preferably equipped with temperature control.
6.2 Resistance heating oven
A resistance heated oven or heating block that can be used at a temperature of at least 220 °C and an
accuracy of ± 10 °C.
6.3 Digestion vessels
The vessels used in the microwave unit shall be equipped with a pressure relieve valve or another technical
equipment which avoids the bursting of the vessels at suddenly occurring excess pressure. The material of
the vessels has to be inert to the acids used for digestion. The digestion vessel shall withstand the pressure of
at least 8 bar. If the amount of organic carbon exceeds 100 mg it has to be ensured that
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.