SIST EN 13348:2008
(Main)Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum
Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum
This European Standard specifies the requirements, sampling, test methods and conditions of delivery for copper tubes.It is applicable to seamless round copper tubes having an outside diameter from 8 mm up to and including 54 mm for pipeline systems for distributing the following medical gases intended to be used at operating pressures up to 2 000 kPa and for systems under vacuum: - oxygen, nitrous oxide, nitrogen, helium, carbon dioxide, xenon; - air for breathing; - specific mixtures of these above mentioned gases; - air for driving surgical tools; - anaesthetic gases and vapours; - vacuum.
Kupfer und Kupferlegierungen - Nahtlose Rundrohre aus Kupfer für medizinische Gase oder Vakuum
Diese Europäische Norm legt die Anforderungen, Probenentnahme, Prüfverfahren und die Lieferbedingungen
für Rohre aus Kupfer fest.
Sie gilt für nahtlose Rundrohre aus Kupfer, die einen Außendurchmesser von 6 mm bis 133 mm haben und
die für Rohrleitungssysteme unter Vakuum und zur Verteilung der folgenden medizinischen Gase bei Arbeitsdrücken
bis 2 000 kPa vorgesehen sind:
⎯ Sauerstoff, Stickstoffoxide, Stickstoff, Helium, Kohlenstoffdioxid, Xenon;
⎯ medizinische Luft;
⎯ spezifische Mischungen aus den oben erwähnten Gasen;
⎯ Luft zum Antrieb chirurgischer Instrumente;
⎯ Gase und Dämpfe für die Anästhesie.
Cuivre et alliages de cuivre - Tubes ronds sans soudure en cuivre pour gaz médicaux ou le vide
La présente Norme européenne établit les exigences, le mode d'échantillonnage, les méthodes d'essai et les conditions de livraison applicables aux tubes en cuivre.
Elle s'applique aux tubes ronds sans soudure en cuivre de diamètre extérieur compris entre 6 mm et 133 mm inclus, destinés à des réseaux de distribution par canalisations sous vide ou à la distribution des gaz médicaux suivants prévus pour être utilisés à des pressions de service pouvant atteindre 2 000 kPa :
l'oxygène, le protoxyde d'azote, l'azote, l'hélium, le dioxyde de carbone, le xénon ;
l’air à usage médical ;
les mélanges spécifiques des gaz spécifiés ci-avant ;
l'air permettant d'actionner les instruments chirurgicaux ;
les gaz et vapeurs anesthésiques.
Baker in bakrove zlitine - Nevarjene okrogle bakrene cevi za medicinske pline ali vakuumske sisteme
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Nevarjene okrogle bakrene cevi za medicinske pline ali vakuumske sistemeKupfer und Kupferlegierungen - Nahtlose Rundrohre aus Kupfer für medizinische Gase oder VakuumCuivre et alliages de cuivre - Tubes ronds sans soudure en cuivre pour gaz médicaux ou le videCopper and copper alloys - Seamless, round copper tubes for medical gases or vacuum77.150.30Bakreni izdelkiCopper products11.040.10Anestezijska, respiratorna in reanimacijska opremaAnaesthetic, respiratory and reanimation equipmentICS:Ta slovenski standard je istoveten z:EN 13348:2008SIST EN 13348:2008en,de01-november-2008SIST EN 13348:2008SLOVENSKI
STANDARDSIST EN 13348:2002/A1:2005SIST EN 13348:20021DGRPHãþD
SIST EN 13348:2008
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13348August 2008ICS 23.040.15Supersedes EN 13348:2001
English VersionCopper and copper alloys - Seamless, round copper tubes formedical gases or vacuumCuivre et alliages de cuivre - Tubes ronds sans soudure encuivre pour gaz médicaux ou le videKupfer und Kupferlegierungen - Nahtlose Rundrohre ausKupfer für medizinische Gase oder VakuumThis European Standard was approved by CEN on 30 May 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13348:2008: ESIST EN 13348:2008
EN 13348:2008 (E) 2 Contents Page Foreword.3 Introduction.5 1 Scope.6 2 Normative references.6 3 Terms and definitions.6 4 Designations.7 5 Ordering information.8 6 Requirements.9 7 Sampling.14 8 Test methods.15 9 Inspection documentation.16 10 Packaging, marking and form of delivery.16 Annex A (normative)
Marking durability test.19 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Pressure Equipment Directive (PED) 97/23/EC.20 Bibliography.21 Tables Table 1 — Mechanical properties.10 Table 2 — Nominal outside diameters and wall thicknesses.11 Table 3 — Tolerances on outside diameter.12 Table 4 — Tolerance on wall thickness.12 Table 5 — Testing of bending and drift expanding.14 Table 6 — Sampling rate.14 Table 7 — Minimum radius of curvature.15 Table 8 — Maximum drill
diameters for the reference standard tube.16 Table 9 — Recommended form of delivery.18 Table ZA.1 — Correspondence between this European Standard and Directive 97/23/EC.20
SIST EN 13348:2008
EN 13348:2008 (E) 3 Foreword This document (EN 13348:2008) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2009, and conflicting national standards shall be withdrawn at the latest by February 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13348:2001 and EN 13348:2001/A1:2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the EU Pressure Equipment Direc-tive (PED) 97/23/EC. For relationship with EU Directive 97/23/EC, see informative Annex ZA, which is an integral part of this docu-ment. Relationship with EU Directive MDD 93/42/EEC: Copper tubes according to EN 13348 cannot be considered as medical devices according EU Directive MDD 93/42/EEC. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 3 "Copper tubes (installation and industrial)" to revise EN 13348:2001: EN 13348, Copper and copper alloys — Seamless, round copper tubes for medical gases or vacuum In comparison with the first edition of EN 13348:2001, the following significant technical changes were made: a) The size range has been increased (6 mm to 133 mm); b) EN 10232 replaced by EN ISO 8491; c) EN 10234 replaced by EN ISO 8493. This is one of a series of European Standards for copper and copper alloy tubes. Other products are specified as follows: EN 1057, Copper and copper alloys — Seamless, round copper tubes for water and gas in sanitary and heat-ing applications EN 12449, Copper and copper alloys — Seamless, round tubes for general purposes EN 12450, Copper and copper alloys — Seamless, round copper capillary tubes EN 12451, Copper and copper alloys — Seamless, round tubes for heat exchangers EN 12452, Copper and copper alloys — Rolled, finned, seamless tubes for heat exchangers EN 12735-1, Copper and copper alloys — Seamless, round copper tubes for air conditioning and refrigeration — Part 1: Tubes for piping systems SIST EN 13348:2008
EN 13348:2008 (E) 4 EN 12735-2, Copper and copper alloys — Seamless, round copper tubes for air conditioning and refrigeration — Part 2: Tubes for equipment EN 13349, Copper and copper alloys — Pre-insulated copper tubes with solid covering EN 13600, Copper and copper alloys — Seamless copper tubes for electrical purposes. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Repub-lic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 13348:2008
EN 13348:2008 (E) 5 Introduction It is recommended that tubes manufactured to this standard are certified as conforming to the requirements of this standard based on continuing surveillance which should be coupled with an assessment of a supplier's quality management system against EN ISO 9001. Tubes to this European Standard are suitable for capillary soldering, brazing or assembling by mechanical compression or collared fittings. NOTE Appropriate precautions should be taken if applying insulating material because it could be detrimental to the copper tube. SIST EN 13348:2008
EN 13348:2008 (E) 6 1 Scope This European Standard specifies the requirements, sampling, test methods and conditions of delivery for copper tubes. It is applicable to seamless round copper tubes having an outside diameter from 6 mm up to and including 133 mm for pipeline systems under vacuum or for distributing the following medical gases intended to be used at operating pressures up to 2 000 kPa: oxygen, nitrous oxide, nitrogen, helium, carbon dioxide, xenon; medical air; specific mixtures of these above mentioned gases; air for driving surgical tools; anaesthetic gases and vapours. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer-ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. prEN 723, Copper and copper alloys — Combustion method for determination of the carbon content on the inner surface of copper tubes or fittings EN 1057:2006, Copper and copper alloys — Seamless, round copper tubes for water and gas in sanitary and heating applications EN 1173, Copper and copper alloys — Material condition designation EN 1971, Copper and copper alloys — Eddy current test for tubes EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test at ambient temperature EN 10204:2004, Metallic products — Types of inspection documents EN ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method (ISO 6507-1:2005) EN ISO 8491, Metallic materials — Tube (in full section) — Bend test (ISO 8491:1998) EN ISO 8493, Metallic materials — Tube — Drift expanding test (ISO 8493:1998) ISO 857-2:2005, Welding and allied processes — Vocabulary — Part 2: Soldering and brazing processes and related terms ISO 1553, Unalloyed copper containing not less than 99,90 % of copper — Determination of copper content — Electrolytic method ISO 4741, Copper and copper alloys — Determination of phosphorus content — Molybdovanadate spectro-metric method 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 seamless round copper tube hollow semi-finished product, circular in cross-section, made of copper, having a uniform wall thickness, which at all stages of production has a continuous periphery [EN 1057:2006] SIST EN 13348:2008
EN 13348:2008 (E) 7 3.2 brazing joining process using filler metal with a liquidus temperature above 450 °C [ISO 857-2:2005] 3.3 mean diameter arithmetical mean of the maximum and minimum outside diameters through the same cross-section of the tube [EN 1057:2006] 3.4 deviation from circular form difference between the maximum and minimum outside diameters measured at any one cross-section of the tube [EN 1057:2006] 3.5 deviation from concentricity half of the difference between the maximum and minimum wall thicknesses at the same cross-section of the tube [EN 1057:2006] 3.6 production batch definite quantity of products of the same form, the same material condition and the same cross-sectional di-mensions manufactured during the same production sequence under uniform conditions [EN 1057:2006] 3.7 permanently marked marked in such a way that the marking will remain readable up to the end of the life of the installation
EXAMPLE Stamping, etching or engraving. [EN 1057:2006] 3.8 durably marked marked in such a way that the marking will remain readable up to the time of commissioning of the installation EXAMPLE Ink marking. [EN 1057:2006] 4 Designations 4.1 Material 4.1.1 General The material is designated either by symbol or number (see 6.1). SIST EN 13348:2008
EN 13348:2008 (E) 8 4.1.2 Symbol The material symbol designation is based on the designation system given in ISO 1190-1. 4.1.3 Number The material number designation is in accordance with the system given in EN 1412. 4.2 Material condition
For the purposes of this European Standard, the following designation, which is in accordance with the system given in EN 1173, applies for the material condition (see Table 1): R. Material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength and elongation requirements. 4.3 Product The product designation provides a standardized pattern of designation from which a rapid and unequivocal description of a product is conveyed in communication. It provides mutual comprehension at the international level with regard to products which meet the requirements of the relevant European Standard. The product designation is no substitute for the full content of the standard. The product designation for products to this European Standard shall consist of: denomination (Copper tube); number of this European Standard (EN 13348); material condition designation (see Table 1); nominal cross-sectional dimensions in millimetres: Outside diameter × wall thickness. The derivation of a product designation is shown in the following example. EXAMPLE Copper tube conforming to this European Standard, in material condition R290 (hard), nominal outside diameter 12 mm, nominal wall thickness 1,0 mm, shall be designated as follows: Copper tube
EN 13348 — R290 — 12 × 1,0 Denomination
Number of this European Standard
Material condition designation
Nominal cross-sectional dimensions in millimetres
5 Ordering information In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and the supplier, the purchaser shall state on his enquiry and order the following information: a) quantity of product required (in metres); b) denomination (Copper tube); SIST EN 13348:2008
EN 13348:2008 (E) 9 c) number of this European Standard (EN 13348); d) material condition designation (see 4.2 and Table 1); e) nominal cross-sectional dimensions in millimetres: outside diameter × wall thickness (see Table 3); f) nominal length (see 10.2); g) form of delivery (see 10.2). In addition, the purchaser shall also state on the enquiry and order the following, if required: h) whether an inspection document is required, and if so, which type (see Clause 9). NOTE It is recommended that the product designation, as described in 4.3, is used for items b) to e). EXAMPLE Ordering details for 500 m copper tube conforming to EN 13348, in material condition R290 (hard), nomi-nal outside diameter 12 mm, nominal wall thickness 1,0 mm, nominal length 5 m, straight lengths:
500 m Copper tube EN 13348 — R290 — 12 ×××× 1,0
— 5 m straight lengths 6 Requirements 6.1 Composition The composition shall conform to the following requirements: Cu + Ag: min. 99,90 %; 0,015
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.