iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 10259:1998

(Main)

Cold-rolled stainless steel wide strip and plate/sheet - Tolerances on dimensions and shape

Cold-rolled stainless steel wide strip and plate/sheet - Tolerances on dimensions and shape

This European Standard applies to cold-rolled stainless, heat resisting and creep resisting steel flat products in thicknesses upto 6,5 mm and rolled widthsof 600 mm upto 2100 mm delivered as: a) wide strip (coils with a rolled width greater or equal to 600 mm), b) sheet or plate cut from wide strip, c) slit cold-rolled wide strip, d) cut lengths obtained from slit cold-rolled wide strip or sheet.

Kaltbreitband und Blech aus nichtrostendem Stahl - Grenzabmaße und Formtoleranzen

Diese europäische Norm gilt für kaltgewalzte Flacherzeugnisse aus nichtrostenden Stählen in Dicken <= 6,5 mm und in Walzbreiten von 600 mm bis zu2100 mm, lieferbar als: a) Kaltbreitband (in Rollen in Walzbreiten >= 600 mm), b) Blech (abgelängt aus Kaltbreitband), c) Längsgeteiltes Kaltbreitband, d) Stäbe (abgelängt aus längsgeteiltem Kaltbreitband oder Blech). Diese Norm gilt nicht für Kaltband (Walzbreiten < 600 mm, siehe EN 10258) oder für kaltgewalzte Erzeugnisse, für die eigene Normen bestehen.

Larges bandes et tôles en acier inoxydable laminées a froid - Tolérances sur les dimensions et la forme

La présente norme européenne est applicable aux produits plats laminés a froid en acier inoxydable et en acier réfractaire, d'épaisseur inférieure ou égale a 6,5 mm et de largeur de laminage comprise entre 600 mm et 2100 mm, livrés sous forme de: a) large bande (bobines avec largeur de laminage >= 600 mm), b) tôle coupée a partir de large bande, c) large bande a froid refendue, d) feuillards coupés a longueur (flans) obtenus a partir de large bande a froid refendue ou detôle.

Hladno valjani široki trakovi in pločevine iz nerjavnih jekel - Mejni odstopki mer in tolerance oblike

General Information

Status
Withdrawn
Publication Date
31-Jul-1998
Withdrawal Date
30-Jun-2006
ICS
77.140.50 - Flat steel products and semi-products
Technical Committee
IFEK - Ferrous metals
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Jul-2006
Due Date
01-Jul-2006
Completion Date
01-Jul-2006
Mandate
M/005 - Mandate to CEN/ECISS concerning standardization in the iron and steel sector
Ref Project
EN 10259:1997 - Cold-rolled stainless steel wide strip and plate/sheet - Tolerances on dimensions and shape

Relations

Replaced By
SIST EN ISO 9445:2006 - Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths - Tolerances on dimensions and form (ISO 9445:2002)
Effective Date
01-Jul-2006

Buy Standard

EN 10259:1998EN 10259:1998
PreviousNext
Standard
EN 10259:1998
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kaltbreitband und Blech aus nichtrostendem Stahl - Grenzabmaße und FormtoleranzenLarges bandes et tôles en acier inoxydable laminées a froid - Tolérances sur les dimensions et la formeCold-rolled stainless steel wide strip and plate/sheet - Tolerances on dimensions and shape77.140.50SROL]GHONLFlat steel products and semi-prod
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 10209:2023(Main)
Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions
EN 10209:2023

This document applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet.
It does not apply to cold rolled narrow strip (rolling width < 600 mm) or to cold rolled flat products for which there is a specific standard, in particular the following:
-   cold-rolled low carbon steel flat products for cold forming (EN 10130);
-   cold-rolled non-oriented electrical steel sheet and strip delivered in fully processed state (EN 10106);
-   cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
-   cold reduced blackplate (EN 10205);
-   steel sheet and strip for welded gas cylinders (EN 10120);
-   cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139);
-   cold-rolled structural steels for general purposes;
-   cold-rolled flat products made of high yield strength for cold forming (EN 10268).

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10359:2023(Main)
Laser welded tailored blanks - Technical delivery conditions
EN 10359:2023

This document specifies the requirements for laser welded tailored blanks (LWB) made of steels for all cold or hot forming processes.
This document applies to all steel grades with or without metallic and/or organic coatings, having uniform or different sheet thickness, welded with or without extra material addition.
After the welding process, LWB are further processed to pressed parts by forming operations under the responsibility of the processor.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10025-4:2019+A1:2023(Main)
Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
EN 10025-4:2019+A1:2022

This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 150 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10025-6:2019+A1:2023(Main)
Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
EN 10025-6:2019+A1:2022

This document specifies technical delivery conditions for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) and are supplied in the quenched and tempered condition.
The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness of 125 mm for grades S890 and S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa to 960 MPa.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10107:2022(Main)
Grain-oriented electrical steel strip and sheet delivered in the fully processed state
EN 10107:2022

This document defines the steel grades of grain-oriented electrical steel strip and sheet in nominal thicknesses of 0,20 mm, 0,23 mm, 0,27 mm, 0,30 mm and 0,35 mm. In particular, it gives general requirements, magnetic properties, geometric characteristics, tolerances and technological characteristics, as well as inspection procedures.
This document applies to Goss textured grain-oriented electrical steel strip and sheet supplied in the final annealed condition in coils or sheets and intended for the construction of magnetic circuits.
The grades are grouped into three classes:
-   conventional grades;
-   high permeability grades;
-   magnetic domain refined high permeability grades.
They correspond to Class C22 of IEC 60404-1.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 17856:2022(Main)
Measurement of the coating properties of non-oriented electrical steel
CEN/TR 17856:2022

This technical report describes the qualification methods, relevant for the non-oriented electrical steel coatings described in EN 10342. In particular, it describes the testing methods, sample preparation, calibration methods, that are necessary to obtain reliable results that can be considered a reference for quality evaluation.

  • Technical report
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10169:2022(Main)
Continuously organic coated (coil coated) steel flat products - Technical delivery conditions
EN 10169:2022

This document specifies requirements for continuously organic coated (coil coated) steel flat products. It particularly specifies the performance requirements.
The products covered are wide strip, sheet cut from wide strip, slit wide strip, strip rolled in widths less than 600 mm and cut lengths (from sheet or strip).
NOTE   National provisions can set up relationships between the performances of the coatings as required in this document and the outdoor atmospheres and ambiances required for a relevant building under study.
This document is not applicable to continuously organic coated flat products made of:
- tin mill products;
- electrical steels.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10202:2022(Main)
Cold reduced tinmill products - Electrolytic tinplate and electrolytic chromium/chromium oxide coated steel
EN 10202:2022

This document specifies requirements for tinmill products in the form of sheets or coils. Tinmill products consist of single and double reduced low carbon mild steel electrolytically coated with either tin (tinplate) or chromium/chromium oxide (ECCS) or (ECCS-RC) (see 3.3).
Single reduced tinmill products are specified in nominal thicknesses that are multiples of 0,005 mm from 0,16 mm up to and including 0,49 mm. Double reduced tinmill products are specified in nominal thicknesses that are multiples of 0,005 mm from 0,12 mm up to and including 0,29 mm.
NOTE 1   Other thicknesses can be ordered upon agreement.
This document applies to coils and sheets cut from coils in nominal minimum widths of 600 mm.
NOTE 2   Standard width coils for specific uses, e.g. tabstock, can be slit into narrow strip for supply in coil form.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10132:2021(Main)
Cold rolled narrow steel strip for heat treatment - Technical delivery conditions
EN 10132:2021

This document specifies the technical delivery conditions for cold rolled narrow steel strip made of non alloy and alloy steel grades in the form of coils and cut lengths in rolling widths less than 600 mm. Cold rolled narrow steel strip is available in grades of case hardening steel and of steels for quenching and tempering for general and special applications particularily springs.
—   Case hardening steels in thicknesses up to and including 10 mm;
—   Steels for quenching and tempering in thicknesses up to and including 6 mm in the conditions annealed (+A), annealed and skin passed (+LC) or cold rolled (+CR);
—   Steels in the quenched and tempered condition (+QT) in thicknesses between 0,30 mm and 3,00 mm.
In special cases supplementary requirements or deviations with respect to this document can be agreed between the purchaser and the supplier at the time of enquiry and order (see 5.2 and Annex A).
In addition to the requirements of this document, the general technical delivery requirements specified in EN 10021 apply.
This document does not cover cold rolled flat products for which separate standards exist, e.g.:
—   Cold rolled uncoated low carbon steel narrow strip for cold forming (EN 10139);
—   Cold rolled steel flat products with higher yield strength for cold forming (EN 10268).

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 10372:2020(Main)
Quality tracking system for flat steel products using barcode - Printing, reading and information processing
EN 10372:2020

This document specifies a method using a barcoding system for tracing potential isolated defects that can be present in the following kinds of coated or uncoated steel flat products, for example:
-   electro-galvanised surface
-   galvanised surface
-   galvannealed surface
-   cold rolled surface
This method, named “quality tracking”, aims at transferring additional material information to the steel users, especially the location of some isolated defects, in a reliable way. This method enables the manufacturer or purchaser to eliminate blanks or coils containing defects.
The method uses a 1D barcode to identify each section of steel strip.
NOTE 1   The stakeholders most involved in this technique are suppliers of steel flat products, car makers, appliance makers, part manufacturers, blanking line builders, steel processors, service centres, etc. All stakeholders can benefit from this project since defects can be traced, and, therefore, the steel containing defects can be eliminated or set apart of the production line.
NOTE 2   In the first stages of development, this method was called "defect tracking" (see [1]) and has been changed into "quality tracking" at the beginning of the standardization process.    
NOTE 3   Quality tracking can be applied to other types of coated or uncoated steel flat products such as pickled and oiled, organic coated, and steels for packaging. Quality tracking can be applied for coiled materials for which the technology of quality tracking is applicable.
NOTE 4   If quality tracking data are used outside of the purpose of quality tracking, it is under the responsibility of the user.
NOTE 5   Quality tracking can be applied to other materials than steel.
NOTE 6   The way to collect the information to be transferred to the user is out of the scope of this document.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day