SIST EN IEC 61400-12-3:2022
(Main)Wind energy generation systems - Part 12-3: Power performance - Measurement based site calibration (IEC 61400-12-3:2022)
Wind energy generation systems - Part 12-3: Power performance - Measurement based site calibration (IEC 61400-12-3:2022)
IEC 61400-12-3:2022 specifies a measurement and analysis procedure for deriving the wind speed correction due to terrain effects and applies to the performance testing of wind turbines of all types and sizes connected to the electrical power network as described in IEC 61400‑12‑1. The procedure applies to the performance evaluation of specific wind turbines at specific locations. The purpose of this part of IEC 61400 is to provide a uniform methodology that will ensure consistency, accuracy and reproducibility in the measurement and analysis of a site calibration for use in the determination of the power performance of wind turbines. This document provides guidance in the measurement, analysis, and reporting of the site calibration for subsequent use in power performance testing for wind turbines.
This first edition of IEC 61400-12-3 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
Windenergieanlagen - Teil 12-3: Leistungsverhalten - Messbasierte Standortkalibrierung (IEC 61400-12-3:2022)
Systèmes de génération d’énergie éolienne - Partie 12-3: Performance de puissance - Étalonnage du site fondé sur le mesurage (IEC 61400-12-3:2022)
IEC 61400-12-3:2022 spécifie une procédure de mesure et d’analyse de dérivation de la correction de vitesse du vent en raison des effets de terrain, et s’applique aux essais de performance d’éoliennes raccordés au réseau électrique de tous types et de toutes tailles, comme cela est décrit dans l’IEC 61400-12-1. La procédure est applicable pour l’évaluation de la performance d'éoliennes spécifiques sur des sites spécifiques. La présente partie de l'IEC 61400 a pour objet de fournir une méthodologie uniforme qui garantit la cohérence, l’exactitude et la reproductibilité du mesurage et de l'analyse d’un étalonnage de site pour utilisation, afin de déterminer la performance de puissance des éoliennes. Le présent document fournit des recommandations relatives au mesurage, à l'analyse et à la consignation des rapports de l’étalonnage du site pour une utilisation ultérieure, dans les essais de performance de puissance des éoliennes.
La présente première édition de l’IEC 61400-12-3 fait partie d'une révision structurelle qui annule et remplace les normes de performance IEC 61400-12-1:2017 et IEC 61400-12-2:2013. Cette révision structurelle ne contient aucune modification technique par rapport à l'IEC 61400-12-1:2017 et l'IEC 61400-12 2:2013. Toutefois, les parties relatives aux mesurages du vent, au mesurage de l'étalonnage du site et à l'évaluation des obstacles et du terrain ont été extraites vers des normes distinctes.
Sistemi za proizvodnjo energije na veter - 12-3. del: Preskušanje zmogljivosti - Kalibracija mesta na podlagi meritev (IEC 61400-12-3:2022)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2022
Sistemi za proizvodnjo energije na veter - 12-3. del: Preskušanje zmogljivosti -
Kalibracija mesta na podlagi meritev (IEC 61400-12-3:2022)
Wind energy generation systems - Part 12-3: Power performance - Measurement based
site calibration (IEC 61400-12-3:2022)
Windenergieanlagen - Teil 12-3: Leistungsverhalten - Messbasierte Standortkalibrierung
(IEC 61400-12-3:2022)
Systèmes de génération d’énergie éolienne - Partie 12-3: Performance de puissance -
Étalonnage du site fondé sur le mesurage (IEC 61400-12-3:2022)
Ta slovenski standard je istoveten z: EN IEC 61400-12-3:2022
ICS:
27.180 Vetrne elektrarne Wind turbine energy systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61400-12-3
NORME EUROPÉENNE
EUROPÄISCHE NORM October 2022
ICS 27.180
English Version
Wind energy generation systems - Part 12-3: Power
performance - Measurement based site calibration
(IEC 61400-12-3:2022)
Systèmes de génération d'énergie éolienne - Partie 12-3: Windenergieanlagen - Teil 12-3: Leistungsverhalten -
Performance de puissance - Étalonnage du site fondé sur le Messbasierte Standortkalibrierung
mesurage (IEC 61400-12-3:2022)
(IEC 61400-12-3:2022)
This European Standard was approved by CENELEC on 2022-10-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61400-12-3:2022 E
European foreword
The text of document 88/824/CDV, future edition 1 of IEC 61400-12-3, prepared by IEC/TC 88 "Wind
energy generation systems" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61400-12-3:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-07-03
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-10-03
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61400-12-3:2022 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61400-50 NOTE Harmonized as EN IEC 61400-50
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61400-12-1 - Wind energy generation systems - Part 12- EN IEC 61400-12-1 -
1: Power performance measurement of
electricity producing wind turbines
IEC 61400-12-5 - Wind energy generation systems - Part 12- EN IEC 61400-12-5 -
5: Power performance - Assessment of
obstacles and terrain
IEC 61400-50-1 - Wind energy generation systems - Part 50- EN IEC 61400-50-1 -
1: Wind Measurement - Application of
Meteorological Mast, Nacelle and Spinner
Mounted Instruments
ISO/IEC Guide 98-3 2008 Uncertainty of measurement - Part 3: - -
Guide to the expression of uncertainty in
measurement (GUM:1995)
Under preparation. Stage at time of publication: FprEN IEC 61400-50-1:2022.
IEC 61400-12-3 ®
Edition 1.0 2022-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Wind energy generation systems –
Part 12-3: Power performance – Measurement based site calibration
Systèmes de génération d'énergie éolienne –
Partie 12-3: Performance de puissance – Étalonnage du site fondé sur le
mesurage
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 27.180 ISBN 978-2-8322-5596-4
– 2 – IEC 61400-12-3:2022 © IEC 2022
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 Symbols, units and abbreviated terms . 10
5 General . 12
6 Overview of the procedure . 13
7 Test set-up . 14
7.1 Considerations for selection of the test wind turbine and location of the
meteorological mast . 14
7.1.1 General . 14
7.1.2 Type A: . 14
7.1.3 Type B: . 14
7.1.4 Type C:. 15
7.2 Instrumentation . 15
8 Data acquisition and rejection criteria . 16
9 Analysis . 17
9.1 General . 17
9.2 Assessment of site shear conditions . 17
9.2.1 Shear calculations and characterisation plots . 17
9.2.2 Assess significance of shear . 17
9.2.3 Establish correlation of shear between locations . 18
9.3 Method 1: Bins of wind direction and wind shear . 19
9.4 Method 2: Linear regression method where wind shear is not a significant
influence . 19
9.5 Additional calculations . 20
10 Site calibration uncertainty . 21
10.1 Site calibration category A uncertainty . 21
10.1.1 Site calibration K-fold analysis . 21
10.1.2 Site calibration statistical uncertainty for each fold. 22
10.2 Site calibration category B uncertainty . 23
10.2.1 General . 23
10.2.2 Anemometer – Pre-calibration . 23
10.2.3 Anemometer – Post-calibration . 23
10.2.4 Anemometer – Classification . 23
10.2.5 Anemometer – Mounting . 24
10.2.6 Anemometer – Data acquisition . 24
10.2.7 Anemometer – Lightning finial. 25
10.3 Combining uncertainties in the wind speed measurement from flow distortion
due to site calibration u . 25
VT,i
10.4 Combined uncertainty . 26
11 Quality checks and additional uncertainties . 26
11.1 Convergence check . 26
11.2 Correlation check for linear regression (see 9.4) . 26
11.3 Change in correction between adjacent wind direction bins . 26
IEC 61400-12-3:2022 © IEC 2022 – 3 –
11.3.1 General . 26
11.3.2 Removal of the wind direction sensor between site calibration and
power performance test . 27
11.4 Site calibration and power performance measurements in different seasons . 28
Annex A (informative) Verification of results . 29
Annex B (informative) Site calibration examples . 31
B.1 Example A . 31
B.1.1 Site description: . 31
B.1.2 Site calibration setup: . 31
B.1.3 Site calibration evaluation: . 31
B.1.4 Step 1: Check the significance of wind shear at the site according to
9.2.2: . 31
B.1.5 Step 2: Verify correlation of wind shear at wind turbine and reference
meteorological mast locations – Example A . 32
B.1.6 Step 3: Calculate results according to 9.2.3 . 33
B.1.7 Step 4: Quality checks and additional uncertainties . 33
B.2 Example B . 35
B.2.1 Site description: . 35
B.2.2 Site calibration setup: . 35
B.2.3 Step 1: Check the significance of wind shear at the site:. 36
B.2.4 Step 2A: Verify correlation of wind shear at wind turbine and reference
meteorological mast locations, example B . 36
B.2.5 Step 2B: Attempt to remove non-correlating wind shear data . 38
B.2.6 Step 3: Calculate results . 39
B.2.7 Step 4: Additional uncertainties: . 39
B.3 Example C . 41
B.3.1 Site description: . 41
B.3.2 Site calibration setup: . 41
B.3.3 Step 1: Check the significance of wind shear at the site:. 42
B.3.4 Step 2: Verify correlation of wind shear at wind turbine and reference
meteorological mast locations, example C . 42
B.3.5 Step 3: Calculate results . 42
B.3.6 Step 4: Quality checks and uncertainty . 42
B.3.7 Anemometer operational uncertainty: . 42
B.3.8 Convergence check: . 42
B.3.9 Change in magnitude of correction between bins: . 43
B.3.10 Wind vane adjustment: . 43
B.3.11 Seasonal uncertainty adjustment: . 43
Bibliography . 44
Figure 1 – Site calibration flow chart . 13
Figure 2 – Terrain types . 15
Figure A.1 – Example of the results of a verification test . 30
Figure B.1 – Wind shear exponent vs. time of day, Example A . 32
Figure B.2 – Wind shear exponents at wind turbine location vs. reference
meteorological mast, example A where the colour axis = wind speed (m/s) . 32
Figure B.3 – Wind speed ratios and number of data points vs. wind shear exponent
and wind direction bin – wind speed ratios (full lines), number of data points (dotted
lines) . 33
– 4 – IEC 61400-12-3:2022 © IEC 2022
Figure B.4 – Data convergence check for 190° bin . 35
Figure B.5 – Wind shear exponent vs. time of day, example B . 36
Figure B.6 – Wind shear exponents at wind turbine location vs. reference
meteorological mast, example B . 36
Figure B.7 – Linear regression of wind turbine location vs. reference meteorological
mast hub height wind speeds for 330° bin . 37
Figure B.8 – Wind speed ratios vs. wind speed for the 330° bin . 37
Figure B.9 – Wind speed ratios vs. wind shear for the 330° bin . 38
Figure B.10 – Wind shear exponents at wind turbine location vs. reference
meteorological mast post-filtering . 38
Figure B.11 – Linear regression of wind turbine location vs. reference meteorological
mast hub height wind speeds for 330° bin, post-filtering . 39
Figure B.12 – Wind speed ratios vs. wind speed for the 330° bin, post-filtering . 39
Figure B.13 – Data convergence check for 330° bin . 40
Figure B.14 – Site calibration wind shear vs. power curve test wind shear . 41
Figure B.15 – Convergence check for 270° bin . 43
Table B.1 – Site calibration flow corrections (wind speed ratio) . 34
Table B.2 – Site calibration data count . 34
Table B.3 – r values for each wind direction bin . 40
Table B.4 – Additional uncertainty due to change in bins for example B . 40
Table B.5 – Additional uncertainty due to change in bins for example C . 43
IEC 61400-12-3:2022 © IEC 2022 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
WIND ENERGY GENERATION SYSTEMS –
Part 12-3: Power performance –
Measurement based site calibration
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61400-12-3 has been prepared by IEC technical committee 88: Wind energy generation
systems. It is an International Standard.
This first edition of IEC 61400-12-3 is part of a structural revision that cancels and replaces the
performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision
contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400-12-2:2013,
but the parts that relate to wind measurements, measurement of site calibration and assessment
of obstacle and terrain have been extracted into separate standards.
The purpose of the re-structure was to allow the future management and revision of the power
performance standards to be carried out more efficiently in terms of time and cost and to provide
a more logical division of the wind measurement requirements into a series of separate
standards which could be referred to by other use case standards in the IEC 61400 series and
subsequently maintained and developed by appropriate experts.
– 6 – IEC 61400-12-3:2022 © IEC 2022
The text of this International Standard is based on the following documents:
Draft Report on voting
88/824/CDV 88/869/RVC
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts in the IEC 61400 series, published under the general title Wind energy
generation systems, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates that it
contains colours which are considered to be useful for the correct understanding of its
contents. Users should therefore print this document using a colour printer.
IEC 61400-12-3:2022 © IEC 2022 – 7 –
INTRODUCTION
The purpose of this part of IEC 61400 is to provide a uniform methodology that will ensure
consistency, accuracy and reproducibility in the measurement and analysis of a site calibration
for use in the determination of the power performance of wind turbines. This document has
been prepared with the anticipation that it would be applied by:
a) a wind turbine manufacturer striving to meet well-defined power performance requirements
and/or a possible declaration system;
b) a wind turbine purchaser in specifying such performance requirements;
c) a wind turbine operator who may be required to verify that stated, or required, power
performance specifications are met for new or refurbished units;
d) a wind turbine planner or regulator who will need to be able to accurately and fairly define
power performance characteristics of wind turbines in response to regulations or permit
requirements for new or modified installations.
This document provides guidance in the measurement, analysis, and reporting of the site
calibration for subsequent use in power performance testing for wind turbines. This document
will benefit those parties involved in the manufacture, installation planning and permitting,
operation, utilization, and regulation of wind turbines. The technically accurate measurement
and analysis techniques recommended in this document should be applied by all parties to
ensure that continuing development and operation of wind turbines is carried out in an
atmosphere of consistent and accurate communication relative to wind turbine performance.
This document presents measurement and reporting procedures expected to provide accurate
results that can be replicated by others. Meanwhile, a user of this document should be aware
of differences that arise from large variations in wind shear and turbulence. Therefore, a user
should consider the influence of these differences and the data selection criteria in relation to
the purpose of the test before contracting the power performance measurements.
The committee recognizes that the restructuring of the IEC 61400-12 series represents a
significant increase in complexity and perhaps greater difficulty to implement. However, it
represents the committee’s best attempt to address issues introduced by larger wind turbines
operating in significant wind shear and complex terrain. The committee recommends that the
new techniques introduced be validated immediately by test laboratories through inter-lab
proficiency testing. The committee recommends a Maintenance Cycle Report be written within
three years of the publication of this document which includes recommendations, clarifications
and simplifications that will improve the practical implementation of this document. If necessary
a revision should be proposed at the same time to incorporate these recommendations,
clarifications and simplifications.
– 8 – IEC 61400-12-3:2022 © IEC 2022
WIND ENERGY GENERATION SYSTEMS –
Part 12-3: Power performance –
Measurement based site calibration
1 Scope
This part of IEC 61400 specifies a measurement and analysis procedure for deriving the wind
speed correction due to terrain effects and applies to the performance testing of wind turbines
of all types and sizes connected to the electrical power network as described in IEC 61400-12-1.
The procedure applies to the performance evaluation of specific wind turbines at specific
locations.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61400-12-1, Wind energy generation systems – Part 12-1: Power performance
measurements of electricity producing wind turbines
IEC 61400-12-5, Wind energy generation systems – Part 12-5: Power performance –
Assessment of obstacles and terrain
IEC 61400-50-1, Wind energy generation systems – Part 50-1: Wind measurement –
Application of meteorological mast, nacelle and spinner mounted instruments
ISO/IEC GUIDE 98-3:2008, Uncertainty of measurement – Part 3: Guide to the expression of
uncertainty in measurement (GUM:1995)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
accuracy
closeness of the agreement between the result of a measurement and a true value of the
measurand
3.2
atmospheric stability
measure of tendency of the wind to encourage or suppress vertical mixing
IEC 61400-12-3:2022 © IEC 2022 – 9 –
Note 1 to entry: Stable atmosphere is characterized by a high temperature gradient with altitude, high wind shear,
possible wind veer and low turbulence relative to unstable conditions. A neutral and unstable atmosphere generally
results in lower temperature gradients and low wind shear.
3.3
complex terrain
terrain surrounding the test site that features significant variations in topography and terrain
obstacles that may cause flow distortion
Note 1 to entry: For the assessment of obstacles and terrain, see IEC 61400-12-5.
3.4
data set
collection of data sampled over a continuous period
3.5
distance constant
indication of the response time of an anemometer, defined as the length of air that shall pass
through the instrument for it to indicate 63 % of the final value for a step input in wind speed
3.6
flow distortion
change in air flow caused by obstacles, topographical variations, or other wind turbines that
results in the wind speed at the measurement location to be different from the wind speed at
the wind turbine location
3.7
hub height
height of the centre of the swept area of the wind turbine rotor above the ground
at the tower
Note 1 to entry: For a vertical axis wind turbine the hub height is defined as the height of the centroid of the swept
area of the rotor above the ground at the tower.
3.8
measured power curve
table and graph that represent the measured, corrected and normalized net power output of a
wind turbine as a function of measured wind speed, measured under a well-defined
measurement procedure
3.9
measurement sector
sector of wind directions from which data are selected for the measured power curve
Note 1 to entry: See IEC 61400-12-5 for determination of measurement sector.
3.10
method of bins
data reduction procedure that groups test data for a certain parameter into intervals (bins)
Note 1 to entry: For each bin, the number of data sets or samples and their sum are recorded, and the average
parameter value within each bin is calculated.
3.11
power performance
measure of the capability of a wind turbine to produce electric power and energy
3.12
rotor equivalent wind speed
wind speed corresponding to the kinetic energy flux through the swept rotor area when
accounting for the variation of the wind speed with height
– 10 – IEC 61400-12-3:2022 © IEC 2022
3.13
standard uncertainty
uncertainty of the result of a measurement expressed as a standard deviation
3.14
test site
location of the wind turbine under test and its surroundings
3.15
uncertainty in measurement
parameter, associated with the result of a measurement, which characterizes the dispersion of
the values that could reasonably be attributed to the measurand
3.16
wind measurement equipment
meteorological mast or remote sensing device
3.17
wind shear
change of wind speed with height across the wind turbine rotor
3.18
wind shear exponent
exponent α of the power law defining the variation of wind speed with height
Note 1 to entry: This parameter is used as a measure of the magnitude of wind shear for site calibration and may
be otherwise useful. The power law equation is
α
z
i
(1)
v = v
zhi
H
where
v is the hub height wind speed;
h
H is the hub height (m);
v is the wind speed at height z ;
zi i
α is the wind shear exponent.
3.19
wind veer
change of wind direction with height across the wind turbine rotor
4 Symbols, units and abbreviated terms
Symbol or Description Unit
abbreviated term
BinSize bin size of wind direction bin
d residual in the j-th 10 min period of fold k [W]
j,k
d standard deviation of site calibration residuals in fold k [W]
std,k
mean value of the residuals in fold k [W]
d
k
F(WD,α) site calibration flow correction determined in 9.2
f number of degrees of freedom of the site calibration
H hub height of wind turbine [m]
k
folds in k-fold cross validation
IEC 61400-12-3:2022 © IEC 2022 – 11 –
Symbol or Description Unit
abbreviated term
L
distance between the wind turbine and the wind measurement equipment [m]
N number of data sets in fold k
k
R Rotor radius [m]
Residual site calibration residual [m/s]
RSD remote sensing device
r
correlation coefficient
s category A standard uncertainty of site calibration [m/s]
VT
s
category A standard uncertainty of site calibration in bin i [m/s]
VT,i
s category A standard uncertainty of site calibration of fold k site calibration [m/s]
VT,k
consistency parameter for wind direction bin j
sccp site calibration consistency parameter for wind direction bin j using the site [°]
j,j-1
calibration correction in bin j-1
sccp site calibration consistency parameter for wind direction bin j using the site [°]
j,j+1
calibration correction in bin j+1
s category A standard uncertainty of the site calibration
VT
u category B standard uncertainty for data acquisition [m/s]
dVT,i
u uncertainty related to the data acquisition of the wind speed signal
dVT,i,j
u category B standard uncertainty for anemometer operational characteristics [m/s]
VT,class,i
u uncertainty related to the classification of the sensors
VT,class,i,j
u category B standard uncertainty for change in correction to wind direction bin [°]
VT,coc,i,j
j
u uncertainty from the site calibration
VT,i,j
u uncertainty related to the lightning finial [m/s]
VT,lgt,i
u category B standard uncertainty for anemometer mounting effects [m/s]
VT,mnti
u
uncertainty related to the mounting of the sensors
VT,mnt,i,j
u category B standard uncertainty for anemometer calibration [m/s]
VT,precal,i
u uncertainty related to the calibration of the anemometers
VT,precal,i,j
u uncertainty related to the post calibration or in-situ calibration of the
VT,postcal,i,j
anemometers
u
category B standard uncertainty for removal of wind direction sensor between [°]
VT,rmv,i,j
site calibration and power performance test
u uncertainty component related to seasonal variation
VT,sv,i
u uncertainty related to the seasonal variation between site calibration and
VT,sv,i,j
power performance test
u category B standard uncertainty for the wind direction sensor [°]
w,i
V reference meteorological mast wind speed [m/s]
PM
V measured wind turbine location wind speed [m/s]
Turb_measured
V predicted wind turbine location wind speed [m/s]
Turb_predicted
v
hub height wind speed [m/s]
h
v wind speed at height z
zi i
WD wind direction bin
[°]
WME wind measurement equipment
α wind shear exponent from power law
– 12 – IEC 61400-12-3:2022 © IEC 2022
5 General
Generally, the wind speed measured upwind of a wind turbine can be assumed to be the same
as that at the turbine location if the turbine were not there. This assumption does not hold when
terrain effects are present. Furthermore, atmospheric conditions may also introduce wind speed
effects. For a power performance measurement carried out according to IEC 61400-12-1, the
wind speed is measured at a reference location 2 to 4 rotor diameters from the turbine under
test whereas the wind speed actually required is that which would be experienced at the turbine
location were the turbine not there. In complex terrain, the wind speed at the reference and
turbine locations can be somewhat different due to the influence of the terrain. Therefore, a site
calibration quantifies and potentially reduces the effects of terrain on the wind speed
measurement. Terrain may cause a systematic difference in wind speed measurement between
the position on the reference meteorological mast where an anemometer is mounted and
another anemometer mounted at the equivalent height above ground at the centre of the wind
turbine rotor at the turbine position. In addition, the relationship between the reference
meteorological mast wind speed and the wind speed at the turbine position may also be affected
by changes in atmospheric stability and/or the shear profile. Wind shear, which is the change
in wind speed with height above the ground, may also be an influential parameter on this
relationship as different shear profiles may cause a different relationship between the
measurement points, especially if the turbine and meteorological mast are at different
elevations.
Seasonal considerations: atmospheric stability, turbulence and wind shear can be related to
different seasonal conditions. There are also concerns as to the effects of changes in roughness
due to changes in the vegetation in the testing area or other roughness changes directly caused
by different seasonal surface characteristics (water/land vs. ice/land, snow, crops, etc.). In light
of these considerations, the site calibration and power curve measurement should be conducted
during the same season or seasons. If the measurements are conducted in different seasons,
additional uncertainty shall be applied as discussed in 11.4.
The outputs of the site calibration are:
a) a table of flow corrections for all wind directions within the measurement sector(s) as defined
in IEC 61400-12-1 and
b) an estimate of the standard uncertainty of these flow corrections which shall be determined
in accordance with the principles of ISO/IEC Guide 98-3:2008.
There are two distinct methods in which the site calibration may be evaluated. Only one method
is required and the method is chosen by evaluating the data to assess shear as discussed in
9.2. The output for each method is:
– Subclause 9.3, Site calibration with shear influence: The flow corrections consist of a matrix
of wind direction bins and wind shear bins where a single wind speed ratio correction factor
is calculated for each point in the matrix.
– Subclause 9.4, Site calibration where shear is not a significant influence: The flow
corrections consist of a slope and an intercept value for each wind direction bin. The
coefficient of determination, r , value for the regression shall also be reported.
This procedure is given for the wind speed defined as the hub height wind speed. This is so
that the procedure does not mandate upper tip height meteorological masts, which are
expensive and may be impractical, as it is possible that remote sensing devices will not be
suitable for measurements in complex terrain. However, where a power curve is to be derived
for the REWS definition of wind speed, then the procedure is repeated for each pair of
measurement heights rather than just for the hub height.
A key element of power performance testing is the measurement of wind speed. This document
requires the use of cup or sonic anemometers or remote sensing devices (RSD) in conjunction
with anemometers to measure wind. Even though suitable procedures for calibration/validation
and classification are adhered to, the nature of the measurement principle of these devices may
potentially cause them to perform differently. These instruments are robust and have been
regarded as suitable for this kind of test with the limitation of some of them to certain classes
of terrain.
IEC 61400-12-3:2022 © IEC 2022 – 13 –
6 Overview of the procedure
Prior to the installation of the wind turbine (or after the removal of it if already existing) two
meteorological masts shall be erected. One meteorological mast is the reference meteorological
mast, which is also used for the power performance test. The second meteorological mast is a
meteorological mast at the wind turbine position.
This procedure intends to characterise the correlation of the wind speeds between the two
positions. Further recommendations for the selection of these positions are provided in 7.1.
The flowchart in Figure 1 provides a general overview of the preparation and analysis process.
Figure 1 – Site calibration flow chart
– 14 – IEC 61400-12-3:2022 © IEC 2022
7 Test set-up
7.1 Considerations for selection of the test wind turbine and location of the
meteorological mast
7.1.1 General
The reference meteorological mast shall be the same meteorological mast that is used for the
power curve measurement. The wind turbine meteorological mast shall be located as close as
possible to the position where the test wind turbine will be or was located and shall be no more
than 0,2 H from the centreline of the wind turbine where H is the wind turbine hub height. It is
recommended that the wind turbine and reference meteorological masts be of the same type
and have the same boom geometry so as to have similar mounting effects on the wind
measurement equipment (WME).
There are a number of factors that can affect site calibration. The most notable of these are
terrain, meteorological mast location, and atmospheric conditions including wi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...