SIST EN 62424:2017
(Main)Representation of process control engineering - Request in P&I diagrams and data exchange between P&ID tools and PCE-CAE tools (IEC 62424:2016)
Representation of process control engineering - Request in P&I diagrams and data exchange between P&ID tools and PCE-CAE tools (IEC 62424:2016)
This International Standard specifies how process control engineering requests are
represented in a P&ID for automatic transferring data between P&ID and PCE tool and to
avoid misinterpretation of graphical P&ID symbols for PCE.
It also defines the exchange of process control engineering request relevant data between a
process control engineering tool and a P&ID tool by means of a data transfer language (called
CAEX). These provisions apply to the export/import applications of such tools.
The representation of the PCE functionality in P&IDs will be defined by a minimum number of
rules to clearly indicate their category and processing function, independent from the
technique of realization (see Clause 6). The definition of graphical symbols for process
equipment (e.g. vessels, valves, columns, etc.), their implementation and rules for the
reference designation system are not in the scope of this standard. These rules are
independent from this standard.
Clause 7 specifies the data flow between the different tools and the data model CAEX.
Darstellung von Aufgaben der Prozessleittechnik - Fließbilder und Datenaustausch zwischen EDV-Werkzeugen zur Fließbilderstellung und CAE-Systemen (IEC 62424:2016)
Représentation de l'ingénierie de commande de processus - Demandes sous forme de diagrammes P&I et échange de données entre outils P&ID et outils PCE-CAE (IEC 62424:2016)
L'IEC 62424:2016 spécifie la méthode de représentation des demandes d'ingénierie de commande de processus dans un diagramme P&I en vue d'un transfert automatique de données entre les outils P&ID et PCE, et de manière à prévenir toute interprétation erronée des symboles P&ID graphiques pour une application PCE. Elle définit également l'échange de données de type demandes d'ingénierie de commande de processus entre un outil d'ingénierie de commande de processus et un outil P&ID au moyen d'un langage de transfert de données (appelé CAEX). Ces dispositions s'appliquent aux fonctions exportation/importation de ces outils. Cette deuxième édition annule et remplace la première édition parue en 2008. Cette édition constitue une révision technique. Elle est une extension compatible de la première édition. Les principales modifications et extensions sont décrites à l'Annexe E et résumées ci-dessous:
- mise à jour et ajout de définitions;
- remplacement du terme "identification" par "désignation de référence";
- mise à jour des catégories PCE et des fonctions de traitement;
- version CAEX 3.0, introduisant les éléments suivants: rôles multiples natifs;
- interfaces imbriquées;
- informations supplémentaires sur le cycle de vie;
- bibliothèque Attribute séparée;
- exemples mis à jour;
- mise à jour du modèle de données électroniques de la demande PCE: nouvelle bibliothèque d'attributs normative pour les attributs de demande PCE de base;
- nouvelle bibliothèque d'attributs étendue informative pour les autres attributs de demande PCE;
- nouveau modèle de données électroniques informatif de la demande PCE.
Predstavitev tehnike nadzora procesov - Zahteve pri diagramih P&I in za izmenjavo podatkov med orodji P&ID ter PCE-CAE (IEC 62424:2016)
Ta mednarodni standard določa, kako so zahteve za nadzor procesov predstavljene v diagramih P&ID za avtomatski prenos podatkov med orodji P&ID in PCE ter za preprečevanje napačnih razlag grafičnih simbolov P&ID s strani orodij PCE.
Določa tudi izmenjavo pomembnih podatkov zahtev za nadzor procesov med orodjem za nadzor procesov in orodjem P&ID na podlagi jezika za prenos podatkov (CAEX). Te določbe se uporabljajo za funkcije izvoza in uvoza podatkov teh orodij.
Predstavitev funkcij PCE v orodjih P&ID bo določena z minimalnim številom pravil, da bosta kategorija in funkcija obdelave teh orodij jasno opredeljeni ter da bo njuna opredelitev neodvisna od tehnik, uporabljenih za njuno realizacijo (glej točko 6). Opredelitev grafičnih simbolov za procesno opremo (npr. posod, ventilov, stolpcev itd.), njihova uvedba in pravila referenčnega sistema za določanje teh simbolov ne spadajo na področje uporabe tega standarda. Ta pravila so neodvisna od tega standarda.
Točka 7 določa pretok podatkov med različnimi orodji in podatkovni model CAEX.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62424:2017
01-maj-2017
1DGRPHãþD
SIST EN 62424:2009
Predstavitev tehnike nadzora procesov - Zahteve pri diagramih P&I in za izmenjavo
podatkov med orodji P&ID ter PCE-CAE (IEC 62424:2016)
Representation of process control engineering - Request in P&I diagrams and data
exchange between P&ID tools and PCE-CAE tools (IEC 62424:2016)
Darstellung von Aufgaben der Prozessleittechnik - Fließbilder und Datenaustausch
zwischen EDV-Werkzeugen zur Fließbilderstellung und CAE-Systemen (IEC
62424:2016)
Représentation de l'ingénierie de commande de processus - Demandes sous forme de
diagrammes P&I et échange de données entre outils P&ID et outils PCE-CAE (IEC
62424:2016)
Ta slovenski standard je istoveten z: EN 62424:2016
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.240.50 Uporabniške rešitve IT v IT applications in industry
industriji
SIST EN 62424:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62424:2017
---------------------- Page: 2 ----------------------
SIST EN 62424:2017
EUROPEAN STANDARD EN 62424
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2016
ICS 25.040.40; 35.240.50 Supersedes EN 62424:2009
English Version
Representation of process control engineering -
Requests in P&I diagrams and data exchange
between P&ID tools and PCE-CAE tools
(IEC 62424:2016)
Représentation de l'ingénierie de commande de processus - Darstellung von Aufgaben der Prozessleittechnik -
Demandes sous forme de diagrammes P&I et échange de Fließbilder und Datenaustausch zwischen EDV-Werkzeugen
données entre outils P&ID et outils PCE-CAE zur Fließbilderstellung und CAE-Systemen
(IEC 62424:2016) (IEC 62424:2016)
This European Standard was approved by CENELEC on 2016-08-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62424:2016 E
---------------------- Page: 3 ----------------------
SIST EN 62424:2017
EN 62424:2016
European foreword
The text of document 65/544/CDV, future edition 2 of IEC 62424, prepared by IEC/TC 65 "Industrial-
process measurement, control and automation" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN 62424:2016.
The following dates are fixed:
(dop) 2017-05-19
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2019-08-19
• latest date by which the national standards conflicting with
the document have to be withdrawn
This document supersedes EN 62424:2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 62424:2016 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60848 NOTE Harmonized as EN 60848.
IEC 61512-1 NOTE Harmonized as EN 61512-1.
IEC 61987-1 NOTE Harmonized as EN 61987-1.
ISO 10628-1 NOTE Harmonized as EN ISO 10628-1.
ISO 10628-2 NOTE Harmonized as EN ISO 10628-2.
ISO 13628-6 NOTE Harmonized as EN ISO 13628-6.
ISO 13703 NOTE Harmonized as EN ISO 13703.
2
---------------------- Page: 4 ----------------------
SIST EN 62424:2017
EN 62424:2016
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61511-1 - Functional safety - Safety instrumented EN 61511-1 -
systems for the process industry sector -
Part 1: Framework, definitions, system,
hardware and application programming
requirements
IEC 81346-1 2009 Industrial systems, installations and EN 81346-1 2009
equipment and industrial products -
Structuring principles and reference
designations -
Part 1: Basic rules
ISO 13849-1 - Safety of machinery - Safety-related EN ISO 13849-1 -
parts of control systems -
Part 1: General principles for design
W3C XML 1.0 2004 Extensible Markup Language (XML) 1.0 - -
3
---------------------- Page: 5 ----------------------
SIST EN 62424:2017
---------------------- Page: 6 ----------------------
SIST EN 62424:2017
IEC 62424
®
Edition 2.0 2016-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Representation of process control engineering – Requests in P&I diagrams and
data exchange between P&ID tools and PCE-CAE tools
Représentation de l'ingénierie de commande de processus – Demandes sous
forme de diagrammes P&I et échange de données entre outils P&ID et outils
PCE-CAE
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.040.40; 35.240.50 ISBN 978-2-8322-3477-8
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 62424:2017
– 2 – IEC 62424:2016 IEC 2016
CONTENTS
FOREWORD . 8
INTRODUCTION . 10
1 Scope . 12
2 Normative references. 12
3 Terms and definitions . 12
4 Abbreviations . 17
5 Conformity . 18
6 Representation of PCE requests in a P&ID . 19
6.1 PCE request and PCE loop . 19
6.2 Objectives and principles . 20
6.3 Requirements for the reference designation and representation of PCE
requests . 20
6.3.1 General . 20
6.3.2 Types of lines . 21
6.3.3 Displaying the location of the operator interface . 21
6.3.4 PCE categories and processing functions . 22
6.3.5 PCE request reference designation system . 25
6.3.6 PU-vendor and typical identification . 26
6.3.7 Device information . 26
6.3.8 Alarming, switching and indicating . 27
6.3.9 Safety-relevant, GMP and quality-relevant PCE requests . 27
6.3.10 PCE control functions . 28
7 Neutral data exchange of PCE relevant P&ID information . 29
7.1 Objectives . 29
7.2 Meaning of P&ID elements . 29
7.3 PCE relevant information of P&ID tools . 30
7.4 Formal description of PCE relevant information of P&ID tools . 31
7.4.1 General object model of a plant hierarchy . 31
7.4.2 General object model of a PCE request . 31
7.5 Modeling PCE relevant information using the CAEX system description
language . 32
7.5.1 Overview . 32
7.5.2 Basic CAEX mappings . 33
7.5.3 Standard CAEX library of PCE request related attributes . 34
7.5.4 Mapping of indirect links between PCE requests of different plant
sections . 35
7.5.5 CAEX description of direct links between PCE requests of different
plant sections. 38
7.5.6 PCE loops. 40
8 Additional PCE attributes . 40
Annex A (normative) CAEX – Data model for machine information exchange . 42
A.1 CAEX and its diagram conventions . 42
A.2 General CAEX concepts . 43
A.2.1 General CAEX terms . 43
A.2.2 General CAEX concept description . 46
A.2.3 Data definition of SystemUnitClass . 50
---------------------- Page: 8 ----------------------
SIST EN 62424:2017
IEC 62424:2016 IEC 2016 – 3 –
A.2.4 Definition of attributes . 52
A.2.5 Data definition of an AttributeType . 54
A.2.6 Data definition of InterfaceClass . 56
A.2.7 Data definition of RoleClass . 59
A.2.8 Modelling of relations . 60
A.2.9 Usage of paths . 68
A.2.10 CAEX role concept . 69
A.2.11 Use of the CAEX MappingObject . 74
A.2.12 References to external CAEX files . 76
A.3 CAEX schema definition . 78
A.3.1 General . 78
A.3.2 Element CAEXFile . 79
A.3.3 CAEXFile/SuperiorStandardVersion . 81
A.3.4 CAEXFile/ SourceDocumentInformation . 81
A.3.5 CAEXFile/ExternalReference . 82
A.3.6 CAEXFile/InstanceHierarchy . 83
A.3.7 CAEXFile/InstanceHierarchy/InternalElement . 84
A.3.8 CAEXFile/InterfaceClassLib . 85
A.3.9 CAEXFile/InterfaceClass . 86
A.3.10 CAEXFile/RoleClassLib . 87
A.3.11 CAEXFile/RoleClass . 88
A.3.12 CAEXFile/SystemUnitClassLib . 89
A.3.13 CAEXFile/SystemUnitClass . 90
A.3.14 CAEXFile/AttributeTypeLib . 91
A.3.15 Group Header . 93
A.3.16 CAEX complex type AttributeFamilyType . 98
A.3.17 CAEX complex type AttributeFamilyType/AttributeType . 99
A.3.18 CAEX complex type AttributeType . 100
A.3.19 CAEX complex type CAEXBasicObject . 108
A.3.20 CAEX complex type CAEXObject . 109
A.3.21 CAEX complex type InterfaceClassType . 110
A.3.22 CAEX complex type InterfaceFamilyType. 113
A.3.23 CAEX complex type InternalElementType . 115
A.3.24 CAEX complex type RoleClassType . 123
A.3.25 CAEX complex type RoleFamilyType . 125
A.3.26 CAEX complexType SourceDocumentInformationType . 128
A.3.27 CAEX complex type SystemUnitClassType . 129
A.3.28 CAEX complex type SystemUnitFamilyType . 136
A.3.29 CAEX simpleType ChangeMode . 138
Annex B (informative) Examples of PCE requests . 139
Annex C (normative) Full XML schema of the CAEX model . 149
Annex D (informative) CAEX modelling examples . 155
D.1 CAEX Attribute Type Library definition for additional attributes . 155
D.2 Example of CAEX InterfaceLib definition . 156
D.3 Example of a CAEX RoleLib definition . 157
D.4 Example CAEX definition of PCE relevant P&ID information . 158
Annex E (informative) List of major changes and extensions of the second edition . 163
Bibliography . 166
---------------------- Page: 9 ----------------------
SIST EN 62424:2017
– 4 – IEC 62424:2016 IEC 2016
Figure 1 – Information flow between P&ID and PCE tool . 11
Figure 2 – Organization of PCE requests . 20
Figure 3 – General representation of a PCE-Request in a P&ID . 21
Figure 4 – Multi-sensing element . 21
Figure 5 – Local interface . 22
Figure 6 – Manually operated switch in local control panel . 22
Figure 7 – Pressure indication in central control room by a central control system . 22
Figure 8 – Example of PCE request reference designation . 26
Figure 9 – Example of flow measurement with indication in the CCR delivered by
vendor A specified by typical identification A20. 26
Figure 10 – Example of pH-measurement with indication in the CCR . 26
Figure 11 – Example of flow measurement with indication in the CCR and high and
low alarm . 27
Figure 12 – Flow measurement with indication in the CCR and high alarm and a high-
high switching function . 27
Figure 13 – Flow measurement with indication in the CCR and a high-high switch limit,
a high alarm, a low alarm and a low-low switch limit for a safety function . 27
Figure 14 – GMP relevant, safety relevant and quality relevant flow measurement with
indication in the CCR . 28
Figure 15 – Control function . 28
Figure 16 – Safety relevant control function . 29
Figure 17 – P&ID elements and associations (PCE relevant items are shown in dark
lines) . 30
Figure 18 – Process data model (PCE relevant items are shown in dark lines) . 31
Figure 19 – PCE request data model . 32
Figure 20 – CAEX data model of major PCE request related attributes . 35
Figure 21 – XML code of the attribute type library . 35
Figure 22 – Example of two plant sections and a signal connection via external
interfaces . 36
Figure 23 – Simplified CAEX model of indirect links between PCE requests across
different plant hierarchy items . 37
Figure 24 – Simplified CAEX model of indirect links between PCE requests across
different plant hierarchy items . 38
Figure 25 – Example of two plant sections and a direct connection . 39
Figure 26 – Simplified CAEX model of direct links between PCE requests across
different sections of a plant . 39
Figure 27 – XML code of the simplified CAEX model . 40
Figure A.1 – XML text of the CAEX source document information . 49
Figure A.2 – CAEX architecture of a SystemUnitClass . 51
Figure A.3 – Example of a SystemUnitClassLib . 51
Figure A.4 – XML code of the example of a SystemUnitClassLib . 52
Figure A.5 – Examples of attributes . 53
Figure A.6 – XML code of the example . 54
Figure A.7 – Example of an AttributeTypeLib and its application in an instance
hierarchy . 55
---------------------- Page: 10 ----------------------
SIST EN 62424:2017
IEC 62424:2016 IEC 2016 – 5 –
Figure A.8 – XML code of the AttributeTypeLib example . 55
Figure A.9 – Example of an InterfaceClassLib . 56
Figure A.10 – XML code of the example of an InterfaceClassLib . 57
Figure A.11 – Second example of an InterfaceClassLib and the usage of nested
interfaces . 57
Figure A.12 – XML code of the second example . 58
Figure A.13 – Usage of Links . 59
Figure A.14 – XML code for the usage of links . 59
Figure A.15 – Example of a RoleClassLib . 60
Figure A.16 – Relations in CAEX . 61
Figure A.17 – XML description of the relations example . 62
Figure A.18 – XML text of the InstanceHierarchy of the relations example . 62
Figure A.19 – XML text of the SystemUnitClassLib of the relations example . 62
Figure A.20 – Example of a parent-child-relation between CAEX InternalElements . 63
Figure A.21 – Example for a hierarchical plant structure . 63
Figure A.22 – Example of a parent-child relation between classes . 64
Figure A.23 – Multiple crossed structures . 67
Figure A.24 – Example for mirror attributes and restructured mirror objects . 67
Figure A.25 – CAEX role concept . 70
Figure A.26 – CAEX data definition for use case 1 . 70
Figure A.27 – CAEX data definition for use case 2 . 71
Figure A.28 – CAEX data definition for use case 3 . 71
Figure A.29 – XML code for use case 3 . 72
Figure A.30 – Multiple role support . 73
Figure A.31 – XML code of the multiple role support example . 74
Figure A.32 – CAEX data definition of a MappingObject . 75
Figure A.33 – XML code for the data definition of a MappingObject . 76
Figure A.34 – Distribution of data in several CAEX files . 77
Figure A.35 – Referencing of external CAEX files . 77
Figure A.36 – XML code for referencing of external CAEX files . 77
Figure A.37 – Example of how to use alias names . 78
Figure A.38 – XML code for the alias example . 78
Figure B.1 – Local level indication, 1 process connection . 139
Figure B.2 – Local level indication, 2 process connections . 139
Figure B.3 – Local flow indication . 139
Figure B.4 – Local pressure indication . 139
Figure B.5 – Local temperature indication . 139
Figure B.6 – Local control panel, pressure indication, high alarm . 140
Figure B.7 – Local temperature indication, CCR temperature high alarm . 140
Figure B.8 – Local pressure indication, CCR pressure high alarm and switch . 140
Figure B.9 – CCR flow indication, device information: Orifice Plate . 140
Figure B.10 – CCR pressure indication, low, low low and high alarm . 140
Figure B.11 – CCR temperature indication and registration . 141
---------------------- Page: 11 ----------------------
SIST EN 62424:2017
– 6 – IEC 62424:2016 IEC 2016
Figure B.12 – CCR level indication and registration, 1 process connection . 141
Figure B.13 – CCR level indication, 2 process connections . 141
Figure B.14 – Two flow indications and flow ratio control in CCR . 141
Figure B.15 – CCR flow indication and high alarm, flow control, control valve with extra
interlock and open/close indication . 142
Figure B.16 – Local pressure indication, CCR pressure indication, high alarm and high
high safety relevant switch; representation of transmitters with integrated local display
(if not otherwise defined in a specification of the field device) . 142
Figure B.17 – Local pressure indication, CCR pressure indication, alarms and switches . 142
Figure B.18 – CCR pressure indication, high and low alarm, safety relevant switch
action on on/off valve . 143
Figure B.19 – Switched valve with on/off indication and switching action, safety
relevant switched valve . 143
Figure B.20 – Pressure restriction . 143
Figure B.21 – Flow restriction .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.