Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for chemical analysis of aluminium nitride powders (ISO 21814:2019)

This document specifies methods for the chemical analysis of fine aluminium nitride powders used as the raw material for fine ceramics.
This document stipulates the determination methods of the aluminium, total nitrogen, boron, calcium, copper, iron, magnesium, manganese, molybdenum, nickel, potassium, silicon, sodium, titanium, tungsten, vanadium, zinc, zirconium, carbon, chlorine, fluorine, and oxygen contents in aluminium nitride powders. The aluminium content is determined by using either an acid pressure decomposition-CyDTA-zinc back titration method or an acid digestion-inductively coupled plasma-optical emission spectrometry (ICP-OES) method. The total nitrogen content is determined by using an acid pressure decomposition-distillation separation-acidimetric titration method, a direct decomposition-distillation separation-acidimetric titration method, or an inert gas fusion-thermal conductivity method. The boron, calcium, copper, iron, magnesium, manganese, molybdenum, nickel, potassium, silicon, sodium, titanium, tungsten, vanadium and zinc contents are determined by using an acid digestion-ICP-OES method or an acid pressure decomposition-ICP-OES method. The sodium and potassium contents are determined via an acid pressure decomposition-flame emission method or an acid pressure decomposition-atomic absorption spectrometry method. The oxygen content is determined by using an inert gas fusion-IR absorption spectrometry method, while that of carbon is determined via a combustion-IR absorption spectrometry method or a combustion-conductometry method. The chlorine and fluorine contents are determined by using a pyrohydrolysation method followed by ion chromatography or spectrophotometry.

Hochleistungskeramik - Verfahren zur chemischen Analyse von Aluminiumnitridpulvern (ISO 21814:2019)

Dieses Dokument legt Verfahren für die chemische Analyse von feinen Aluminiumnitridpulvern fest, die als Rohstoffe für Hochleistungskeramik verwendet werden.
Dieses Dokument legt die Verfahren zur Bestimmung der Gehalte an Aluminium, Gesamtstickstoff, Bor, Calcium, Kupfer, Eisen, Magnesium, Mangan, Molybdän, Nickel, Kalium, Silicium, Natrium, Titan, Wolfram, Vanadium, Zink, Zirconium, Kohlenstoff, Chlor, Fluor und Sauerstoff in Aluminiumnitridpulvern fest. Der Aluminiumgehalt wird entweder mittels CyDTA-Zink-Rücktitration nach Säuredruckaufschluss oder mittels optischer Emissionsspektrometrie mit induktiv gekoppeltem Plasma (ICP-OES, en: inductively coupled plasma-optical emission spectrometry) nach Säureaufschluss bestimmt. Der Gesamtstickstoffgehalt wird mittels acidimetrischer Titration nach Säuredruckaufschluss und Destillationstrennung, acidimetrischer Titration nach direktem Aufschluss und Destillationstrennung oder mittels thermischer Konduktometrie nach Inertgas-Schmelzextraktion bestimmt. Die Gehalte an Bor, Calcium, Kupfer, Eisen, Magnesium, Mangan, Molybdän, Nickel, Kalium, Silicium, Natrium, Titan, Wolfram, Vanadium und Zink werden mittels ICP-OES nach Säureaufschluss oder Säuredruckaufschluss bestimmt. Die Gehalte an Natrium und Kalium werden mittels Flammenemission nach Säuredruckaufschluss oder mittels Atomabsorptions¬spektrometrie nach Säuredruckaufschluss bestimmt. Der Sauerstoffgehalt wird mittels IR-Absorptions¬spektrometrie nach Inertgas-Schmelzextraktion bestimmt, der Kohlenstoffgehalt mittels IR Absorptions¬spektrometrie nach Verbrennung oder mittels konduktometrischer Bestimmung nach Verbrennung. Die Gehalte an Chlor und Fluor werden mittels Pyrohydrolyse und anschließender Ionenchromatographie oder Spektrophotometrie bestimmt.

Céramiques techniques - Méthodes d'analyse chimique des poudres de nitrure d'aluminium (ISO 21814:2019)

Le présent document spécifie des méthodes d’analyse chimique des poudres de nitrure d’aluminium utilisées comme matière première pour les céramiques techniques.
Le présent document stipule les méthodes de détermination des teneurs en aluminium, azote total, bore, calcium, cuivre, fer, magnésium, manganèse, molybdène, nickel, potassium, silicium, sodium, titane, tungstène, vanadium, zinc, zirconium, carbone, chlore, fluor et oxygène des poudres de nitrure d’aluminium. La teneur en aluminium est déterminée à l’aide d’une méthode par décomposition sous pression en milieu acide / CyDTA / titrage en retour au zinc, ou d’une méthode par digestion acide / spectrométrie d’émission optique avec plasma à couplage inductif (ICP-OES). La teneur totale en azote est déterminée à l’aide d’une méthode par décomposition sous pression en milieu acide / séparation par distillation / titrage acidimétrique, d’une méthode par décomposition directe: séparation par distillation / titrage acidimétrique, ou d’une méthode par fusion sous gaz inerte / conductivité thermique. Les teneurs en bore, calcium, cuivre, fer, magnésium, manganèse, molybdène, nickel, potassium, silicium, sodium, titane, tungstène, vanadium et zinc sont déterminées à l’aide d’une méthode par digestion acide / ICP-OES ou d’une méthode par décomposition sous pression en milieu acide / ICP-OES. Les teneurs en sodium et potassium sont déterminées à l’aide d’une méthode par décomposition sous pression en milieu acide / émission de flamme, ou d’une méthode par décomposition sous pression en milieu acide / spectrométrie d’absorption atomique. La teneur en oxygène est déterminée à l’aide d’une méthode par fusion sous gaz inerte / spectrométrie d’absorption IR, tandis que la teneur en carbone est déterminée à l’aide d’une méthode par combustion / spectrométrie d’absorption IR ou d’une méthode par conduction / conductimétrie. Les teneurs en chlore et en fluor sont déterminées à l’aide d’une méthode par pyrohydrolyse suivie d’une chromatographie ionique ou d’une spectrophotométrie.

Fina keramika (sodobna keramika, sodobna tehnična keramika) - Preskusne metode za kemične analize praškov aluminijevega nitrida (ISO 21814:2019)

Ta dokument določa metode za kemično analizo finih praškov aluminijevega nitrida, ki se uporabljajo kot surovina za fino keramiko.
Ta dokument določa metode za določevanje vsebnosti aluminija, skupnega dušika, bora, kalcija, bakra, železa, magnezija, mangana, molibdena, niklja, kalija, silicija, natrija, titana, volframa, vanadija, cinka, cirkonija, ogljika, klora, fluora in kisika v praških aluminijevega nitrida. Vsebnost aluminija se določi z uporabo metode povratne titracije s CyDTA/cinkom v kombinaciji s kislinsko razgradnjo ali metode optične emisijske spektrometrije z induktivno sklopljeno plazmo (ICP-OES) v kombinaciji z razklopom v kislini. Vsebnost skupnega dušika se določi z uporabo metode acidimetrične titracije z destilacijskim ločevanjem v kombinaciji s kislinsko razgradnjo, metode acidimetrične titracije z destilacijskim ločevanjem v kombinaciji z neposredno razgradnjo ali metodo toplotne prevodnosti v kombinaciji s fuzijo inertnega plina. Vsebnost bora, kalcija, bakra, železa, magnezija, mangana, molibdena, niklja, kalija, silicija, natrija, titana, volframa, vanadija in cinka se določi z uporabo metode optične emisijske spektrometrije z induktivno sklopljeno plazmo v kombinaciji s kislinsko razgradnjo. Vsebnost natrija in kalija se določi z uporabo metode plamenske emisije ali metode atomske absorpcijske spektrometrije v kombinaciji s kislinsko razgradnjo. Vsebnost kisika se določi z uporabo metode IR-absorpcijske spektrometrije v kombinaciji s fuzijo inertnega plina, vsebnost ogljika pa z metodo IR-absorpcijske spektrometrije v kombinaciji z zgorevanjem ali metodo konduktometrije v kombinaciji z zgorevanjem. Vsebnost klora in fluora se določi z uporabo metode pirohidrolizacije, ki ji sledi ionska kromatografija ali spektrofotometrija.

General Information

Status
Published
Public Enquiry End Date
18-Oct-2022
Publication Date
13-Dec-2022
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
07-Dec-2022
Due Date
11-Feb-2023
Completion Date
14-Dec-2022

Relations

Buy Standard

Standard
EN ISO 21814:2023
English language
45 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 21814:2022
English language
42 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 21814:2023
01-februar-2023
Nadomešča:
SIST EN 725-4:2007
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Preskusne
metode za kemične analize praškov aluminijevega nitrida (ISO 21814:2019)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for
chemical analysis of aluminium nitride powders (ISO 21814:2019)
Hochleistungskeramik - Verfahren zur chemischen Analyse von Aluminiumnitridpulvern
(ISO 21814:2019)
Céramiques techniques - Méthodes d'analyse chimique des poudres de nitrure
d'aluminium (ISO 21814:2019)
Ta slovenski standard je istoveten z: EN ISO 21814:2022
ICS:
81.060.30 Sodobna keramika Advanced ceramics
SIST EN ISO 21814:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 21814:2023

---------------------- Page: 2 ----------------------
SIST EN ISO 21814:2023


EN ISO 21814
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2022
EUROPÄISCHE NORM
ICS 81.060.30 Supersedes EN 725-4:2006
English Version

Fine ceramics (advanced ceramics, advanced technical
ceramics) - Methods for chemical analysis of aluminium
nitride powders (ISO 21814:2019)
Céramiques techniques - Méthodes d'analyse chimique Hochleistungskeramik - Verfahren zur chemischen
des poudres de nitrure d'aluminium (ISO 21814:2019) Analyse von Aluminiumnitridpulvern (ISO
21814:2019)
This European Standard was approved by CEN on 21 November 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21814:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 21814:2023
EN ISO 21814:2022 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 21814:2023
EN ISO 21814:2022 (E)
European foreword
The text of ISO 21814:2019 has been prepared by Technical Committee ISO/TC 206 "Fine ceramics” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 21814:2022
by Technical Committee CEN/TC 184 “Advanced technical ceramics” the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 725-4:2006.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 21814:2019 has been approved by CEN as EN ISO 21814:2022 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 21814:2023

---------------------- Page: 6 ----------------------
SIST EN ISO 21814:2023
INTERNATIONAL ISO
STANDARD 21814
First edition
2019-02
Fine ceramics (advanced ceramics,
advanced technical ceramics) —
Methods for chemical analysis of
aluminium nitride powders
Céramiques techniques — Méthodes d’analyse chimique des poudres
de nitrure d'aluminium
Reference number
ISO 21814:2019(E)
©
ISO 2019

---------------------- Page: 7 ----------------------
SIST EN ISO 21814:2023
ISO 21814:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 21814:2023
ISO 21814:2019(E)

Contents Page
Foreword .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Analytes and ranges . 2
5 Preparation of the test sample . 2
5.1 General . 2
5.2 Sampling . 3
5.3 Drying . 3
5.4 Weighing . 3
6 Reporting the analytical values . 3
6.1 Number of analyses. 3
6.2 Blank test . 3
6.3 Evaluation of the analytical values. 3
6.4 Expression of the analytical values . 3
7 Determination of the aluminium content . 4
7.1 Classification of the determination methods . 4
7.2 Acid decomposition-ICP-OES method . 4
7.2.1 Principle . 4
7.2.2 Reagents . 4
7.2.3 Apparatus and instruments. 4
7.2.4 Procedure . 5
7.2.5 Blank test . 5
7.2.6 Drawing of the calibration curve . 5
7.2.7 Calculation . 5
7.3 Acid pressure decomposition-CyDTA-zinc back titration method . 5
7.3.1 Principle . 5
7.3.2 Reagents . 6
7.3.3 Apparatus and instruments. 6
7.3.4 Procedure . 8
7.3.5 Blank test . 8
7.3.6 Calculation . 8
8 Determination of the total nitrogen content . 8
8.1 Classification of the determination methods . 8
8.2 Acid pressure decomposition-distillation separation-acidimetric titration method . 9
8.2.1 Principle . 9
8.2.2 Reagents . 9
8.2.3 Apparatus .10
8.2.4 Procedure .12
8.2.5 Recovery measurement .12
8.2.6 Calculation .13
8.3 Direct decomposition-distillation separation-acidimetric titration method .13
8.3.1 Principle .13
8.3.2 Reagents .13
8.3.3 Apparatus .13
8.3.4 Procedure .13
8.3.5 Recovery measurement .13
8.3.6 Calculation .13
8.4 Inert gas fusion-thermal conductivity method .13
8.4.1 Principle .13
8.4.2 Reagents .14
8.4.3 Apparatus .14
© ISO 2019 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 21814:2023
ISO 21814:2019(E)

8.4.4 Instrument .14
8.4.5 Procedure .15
8.4.6 Blank test .16
8.4.7 Calculation of the calibration coefficient .16
8.4.8 Calculation .17
9 Determination of the sodium and potassium contents .17
9.1 Classification of the determination methods .17
9.2 Acid pressure decomposition-flame emission method .17
9.2.1 Principle .17
9.2.2 Reagents .17
9.2.3 Instruments .18
9.2.4 Procedure .18
9.2.5 Blank test .18
9.2.6 Drawing of the calibration curve .18
9.2.7 Calculation .18
9.3 Acid pressure decomposition-atomic absorption spectrometry method .19
9.3.1 Principle .19
9.3.2 Reagents .19
9.3.3 Instruments .19
9.3.4 Procedure .19
9.3.5 Blank test .19
9.3.6 Drawing of the calibration curve .19
9.3.7 Calculation .19
10 Determination of the trace element contents .19
10.1 Classification of the determination methods .19
10.2 Acid decomposition-ICP-OES method .20
10.2.1 Principle .20
10.2.2 Reagents .20
10.2.3 Apparatus and instruments.20
10.2.4 Procedure .21
10.2.5 Blank test .21
10.2.6 Drawing of the calibration curve .21
10.2.7 Calculation .21
10.3 Acid pressure decomposition-ICP-OES method .22
10.3.1 General.22
10.3.2 Reagents .22
10.3.3 Apparatus and instruments.22
10.3.4 Procedure .22
10.3.5 Blank test .22
10.3.6 Drawing of the calibration curve .22
10.3.7 Calculation .22
11 Determination of the oxygen content .22
11.1 Principle .22
11.2 Reagents.22
11.3 Apparatus .23
11.4 Instruments .23
11.5 Procedure .23
11.6 Blank test .23
11.7 Calculation of the calibration coefficient .23
11.8 Calculation .23
12 Determination of the carbon content .24
12.1 Classification of the determination methods .24
12.2 Combustion (resistance furnace)-IR absorption spectrometry .24
12.2.1 Principle .24
12.2.2 Reagents .24
12.2.3 Apparatus .24
iv © ISO 2019 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 21814:2023
ISO 21814:2019(E)

12.2.4 Instrument .24
12.2.5 Procedure .25
12.2.6 Blank test .26
12.2.7 Calculation of the calibration coefficient .26
12.2.8 Calculation .27
12.3 Combustion (radio frequency heating furnace)-thermal conductometry .27
12.3.1 Principle .27
12.3.2 Reagents .27
12.3.3 Apparatus .27
12.3.4 Instrument .27
12.3.5 Procedure .28
12.3.6 Blank test .29
12.3.7 Calculation of the calibration coefficient .29
12.3.8 Calculation .29
12.4 Combustion (radio frequency heating furnace)-IR absorption spectrometry .29
12.4.1 Principle .29
12.4.2 Reagents .29
12.4.3 Apparatus .29
12.4.4 Instrument .
...

SLOVENSKI STANDARD
oSIST prEN ISO 21814:2022
01-september-2022
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Preskusne
metode za kemične analize praškov aluminijevega nitrida (ISO 21814:2019)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for
chemical analysis of aluminium nitride powders (ISO 21814:2019)
Hochleistungskeramik - Verfahren zur chemischen Analyse von Aluminiumnitridpulvern
(ISO 21814:2019)
Céramiques techniques - Méthodes d'analyse chimique des poudres de nitrure
d'aluminium (ISO 21814:2019)
Ta slovenski standard je istoveten z: prEN ISO 21814
ICS:
81.060.30 Sodobna keramika Advanced ceramics
oSIST prEN ISO 21814:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 21814:2022

---------------------- Page: 2 ----------------------
oSIST prEN ISO 21814:2022
INTERNATIONAL ISO
STANDARD 21814
First edition
2019-02
Fine ceramics (advanced ceramics,
advanced technical ceramics) —
Methods for chemical analysis of
aluminium nitride powders
Céramiques techniques — Méthodes d’analyse chimique des poudres
de nitrure d'aluminium
Reference number
ISO 21814:2019(E)
©
ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 21814:2022
ISO 21814:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 21814:2022
ISO 21814:2019(E)

Contents Page
Foreword .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Analytes and ranges . 2
5 Preparation of the test sample . 2
5.1 General . 2
5.2 Sampling . 3
5.3 Drying . 3
5.4 Weighing . 3
6 Reporting the analytical values . 3
6.1 Number of analyses. 3
6.2 Blank test . 3
6.3 Evaluation of the analytical values. 3
6.4 Expression of the analytical values . 3
7 Determination of the aluminium content . 4
7.1 Classification of the determination methods . 4
7.2 Acid decomposition-ICP-OES method . 4
7.2.1 Principle . 4
7.2.2 Reagents . 4
7.2.3 Apparatus and instruments. 4
7.2.4 Procedure . 5
7.2.5 Blank test . 5
7.2.6 Drawing of the calibration curve . 5
7.2.7 Calculation . 5
7.3 Acid pressure decomposition-CyDTA-zinc back titration method . 5
7.3.1 Principle . 5
7.3.2 Reagents . 6
7.3.3 Apparatus and instruments. 6
7.3.4 Procedure . 8
7.3.5 Blank test . 8
7.3.6 Calculation . 8
8 Determination of the total nitrogen content . 8
8.1 Classification of the determination methods . 8
8.2 Acid pressure decomposition-distillation separation-acidimetric titration method . 9
8.2.1 Principle . 9
8.2.2 Reagents . 9
8.2.3 Apparatus .10
8.2.4 Procedure .12
8.2.5 Recovery measurement .12
8.2.6 Calculation .13
8.3 Direct decomposition-distillation separation-acidimetric titration method .13
8.3.1 Principle .13
8.3.2 Reagents .13
8.3.3 Apparatus .13
8.3.4 Procedure .13
8.3.5 Recovery measurement .13
8.3.6 Calculation .13
8.4 Inert gas fusion-thermal conductivity method .13
8.4.1 Principle .13
8.4.2 Reagents .14
8.4.3 Apparatus .14
© ISO 2019 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 21814:2022
ISO 21814:2019(E)

8.4.4 Instrument .14
8.4.5 Procedure .15
8.4.6 Blank test .16
8.4.7 Calculation of the calibration coefficient .16
8.4.8 Calculation .17
9 Determination of the sodium and potassium contents .17
9.1 Classification of the determination methods .17
9.2 Acid pressure decomposition-flame emission method .17
9.2.1 Principle .17
9.2.2 Reagents .17
9.2.3 Instruments .18
9.2.4 Procedure .18
9.2.5 Blank test .18
9.2.6 Drawing of the calibration curve .18
9.2.7 Calculation .18
9.3 Acid pressure decomposition-atomic absorption spectrometry method .19
9.3.1 Principle .19
9.3.2 Reagents .19
9.3.3 Instruments .19
9.3.4 Procedure .19
9.3.5 Blank test .19
9.3.6 Drawing of the calibration curve .19
9.3.7 Calculation .19
10 Determination of the trace element contents .19
10.1 Classification of the determination methods .19
10.2 Acid decomposition-ICP-OES method .20
10.2.1 Principle .20
10.2.2 Reagents .20
10.2.3 Apparatus and instruments.20
10.2.4 Procedure .21
10.2.5 Blank test .21
10.2.6 Drawing of the calibration curve .21
10.2.7 Calculation .21
10.3 Acid pressure decomposition-ICP-OES method .22
10.3.1 General.22
10.3.2 Reagents .22
10.3.3 Apparatus and instruments.22
10.3.4 Procedure .22
10.3.5 Blank test .22
10.3.6 Drawing of the calibration curve .22
10.3.7 Calculation .22
11 Determination of the oxygen content .22
11.1 Principle .22
11.2 Reagents.22
11.3 Apparatus .23
11.4 Instruments .23
11.5 Procedure .23
11.6 Blank test .23
11.7 Calculation of the calibration coefficient .23
11.8 Calculation .23
12 Determination of the carbon content .24
12.1 Classification of the determination methods .24
12.2 Combustion (resistance furnace)-IR absorption spectrometry .24
12.2.1 Principle .24
12.2.2 Reagents .24
12.2.3 Apparatus .24
iv © ISO 2019 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 21814:2022
ISO 21814:2019(E)

12.2.4 Instrument .24
12.2.5 Procedure .25
12.2.6 Blank test .26
12.2.7 Calculation of the calibration coefficient .26
12.2.8 Calculation .27
12.3 Combustion (radio frequency heating furnace)-thermal conductometry .27
12.3.1 Principle .27
12.3.2 Reagents .27
12.3.3 Apparatus .27
12.3.4 Instrument .27
12.3.5 Procedure .28
12.3.6 Blank test .29
12.3.7 Calculation of the calibration coefficient .29
12.3.8 Calculation .29
12.4 Combustion (radio frequency heating furnace)-IR absorption spectrometry .29
12.4.1 Principle .29
12.4.2 Reagents .29
12.4.3 Apparatus .29
12.4.4 Instrument .29
12.4.5 Procedure .30
12.4.6 Blank test .31
12.4.7 Calculation of the calibration coefficient .31
12.4.8 Calculation .31
13 Determination of the fluorine and chlorine contents .31
13.1 Principle .31
13.2 Reagents.31
13.3 Apparatus and instruments .32
13.4 Procedure .33
13.4.1 Extraction of fluorine and chlorine from the sample .33
13.4.2 Determination of the fluorine and chlorine contents .33
13.5 Blank test .33
13.6 Drawing of the calibration curve .34
13.7 Calculation .34
14 Test report .34
Annex A (informative) Analytical results obtained from the round robin test .35
Bibliography .36
© ISO 2019 – All rights reserved v

---------------------- Page: 7 ----------------------
oSIST prEN ISO 21814:2022
ISO 21814:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.