SIST EN 61784-5-19:2014

Industrial communication networks - Profiles -- Part 5-19: Installation of fieldbuses - Installation profiles for CPF 19

This part of IEC 61784 specifies the installation profiles for CPF 19 (MECHATROLINK™1). The installation profiles are specified in the annexes. These annexes are read in conjunction with IEC 61918:2013.

Industrielle Kommunikationsnetze - Profile -- Teil 5-19: Feldbusinstallation - Installationsprofile für die Kommunikationsprofilfamilie 19

Réseaux de communication industriels - Profils -- Partie 5-19: Installation des bus de terrain - Profils d'installation pour CPF 19

La CEI 61784-5-19:2013 définit les profils d'installation pour la CPF 19 (MECHATROLINK). Chaque profil d'installation de CP est spécifié dans une partie séparée de la présente série de normes. Cette norme fait partie d'une série élaborée pour faciliter l'utilisation des réseaux de communication dans des systèmes de contrôle-commande industriels. La présente norme doit être utilisée conjointement à la CEI 61918:2013.

Industrijska komunikacijska omrežja - Profili - 5-19. del: Inštalacija procesnih vodil - Inštalacijski profili za CPF 19 (IEC 61784-5-19:2013)

General Information

• Status: Published
• Publication Date: 09-Mar-2014
• ICS: 25.040.40 - Industrial process measurement and control
• ICS: 35.100.40 - Transport layer
• Technical Committee: MOV - Measuring equipment for electromagnetic quantities
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 20-Dec-2013
• Due Date: 24-Feb-2014
• Completion Date: 10-Mar-2014
• Ref Project: EN 61784-5-19:2013 - Industrial communication networks - Profiles - Part 5-19: Installation of fieldbuses - Installation profiles for CPF 19

Relations

• Revised: oSIST prEN IEC 61784-5-19:2022 - Industrial communication networks - Profiles - Part 5-19: Installation of fieldbuses - Installation profiles for CPF 19
• Effective Date: 03-Aug-2021

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61784-5-19:2014
01-april-2014
Industrijska komunikacijska omrežja - Profili - 5-19. del: Inštalacija procesnih vodil
- Inštalacijski profili za CPF 19 (IEC 61784-5-19:2013)
Industrial communication networks - Profiles -- Part 5-19: Installation of fieldbuses -
Installation profiles for CPF 19
Industrielle Kommunikationsnetze - Profile -- Teil 5-19: Feldbusinstallation -
Installationsprofile für die Kommunikationsprofilfamilie 19
Réseaux de communication industriels - Profils -- Partie 5-19: Installation des bus de
terrain - Profils d'installation pour CPF 19
Ta slovenski standard je istoveten z: EN 61784-5-19:2013
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.100.40 Transportni sloj Transport layer
SIST EN 61784-5-19:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61784-5-19:2014

---------------------- Page: 2 ----------------------

SIST EN 61784-5-19:2014

EUROPEAN STANDARD
EN 61784-5-19

NORME EUROPÉENNE
December 2013
EUROPÄISCHE NORM

ICS 25.040.40; 35.100.40


English version


Industrial communication networks -
Profiles -
Part 5-19: Installation of fieldbuses -
Installation profiles for CPF 19
(IEC 61784-5-19:2013)


Réseaux de communication industriels -  Industrielle Kommunikationsnetze -
Profils - Profile -
Partie 5-19: Installation des bus de terrain Teil 5-19: Feldbusinstallation -
- Profils d'installation pour CPF 19 Installationsprofile für die
(CEI 61784-5-19:2013) Kommunikationsprofilfamilie 19
(IEC 61784-5-19:2013)




This European Standard was approved by CENELEC on 2013-10-14. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61784-5-19:2013 E

---------------------- Page: 3 ----------------------

SIST EN 61784-5-19:2014
EN 61784-5-19:2013 - 2 -
Foreword
The text of document 65C/738/FDIS, future edition 1 of IEC 61784-5-19, prepared by
SC 65C "Industrial networks" of IEC/TC 65 "Industrial-process measurement, control and automation"
was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 61784-5-19:2013.

The following dates are fixed:
• latest date by which the document has to be (dop) 2014-07-14
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-10-14
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This standard is to be used in conjunction with EN 61918:2013.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 61784-5-19:2013 was approved by CENELEC as a
European Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 61784-5-19:2014
- 3 - EN 61784-5-19:2013
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Annex ZA of EN 61918:2013 applies, except as follows:

Publication Year Title EN/HD Year
Addition to Annex ZA of EN 61918:2013:
IEC 61918 2013 Industrial communication networks - EN 61918 2013
Installation of communication networks in
industrial premises

---------------------- Page: 5 ----------------------

SIST EN 61784-5-19:2014

---------------------- Page: 6 ----------------------

SIST EN 61784-5-19:2014




IEC 61784-5-19

®


Edition 1.0 2013-09




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Industrial communication networks – Profiles –

Part 5-19: Installation of fieldbuses – Installation profiles for CPF 19




Réseaux de communication industriels – Profils –

Partie 5-19: Installation des bus de terrain – Profils d'installation pour CPF 19
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX X


ICS 25.040.40; 35.100.40 ISBN 978-2-8322-1073-4



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61784-5-19:2014
– 2 – 61784-5-19 © IEC:2013
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms, definitions and abbreviated terms . 8
4 CPF19: Overview of installation profiles . 8
5 Installation profile conventions . 8
6 Conformance to installation profiles . 9
Annex A (normative) CP 19/1 (MECHATROLINK-II) specific installation profile . 11
A.1 Installation profile scope . 11
A.2 Normative references . 11
A.3 Installation profile terms, definitions, and abbreviated terms . 11
A.3.1 Terms and definitions . 11
A.3.2 Abbreviated terms . 11
A.3.3 Conventions for installation profiles . 11
A.4 Installation planning . 12
A.4.1 General . 12
A.4.2 Planning requirements . 12
A.4.3 Network capabilities . 12
A.4.4 Selection and use of cabling components . 14
A.4.5 Cabling planning documentation . 21
A.4.6 Verification of cabling planning specification . 21
A.5 Installation implementation . 22
A.5.1 General requirements . 22
A.5.2 Cable installation . 22
A.5.3 Connector installation . 23
A.5.4 Terminator installation . 24
A.5.5 Device installation . 24
A.5.6 Coding and labelling . 24
A.5.7 Earthing and bonding of equipment and devices and shield cabling . 24
A.5.8 As-implemented cabling documentation . 25
A.6 Installation verification and installation acceptance test . 25
A.6.1 General . 25
A.6.2 Installation verification . 25
A.6.3 Installation acceptance test . 26
A.7 Installation administration . 26
A.8 Installation maintenance and installation troubleshooting . 27
Annex B (normative) CP 19/2 (MECHATROLINK-III) specific installation profile . 29
B.1 Installation profile scope . 29
B.2 Normative references . 29
B.3 Installation profile terms, definitions, and abbreviated terms . 29
B.3.1 Terms and definitions . 29
B.3.2 Abbreviated terms . 29
B.3.3 Conventions for installation profiles . 29

---------------------- Page: 8 ----------------------

SIST EN 61784-5-19:2014
61784-5-19 © IEC:2013 – 3 –
B.4 Installation planning . 29
B.4.1 General . 29
B.4.2 Planning requirements . 29
B.4.3 Network capabilities . 30
B.4.4 Selection and use of cabling components . 31
B.4.5 Cabling planning documentation . 36
B.4.6 Verification of cabling planning specification . 36
B.5 Installation implementation . 37
B.5.1 General requirements . 37
B.5.2 Cable installation . 37
B.5.3 Connector installation . 38
B.5.4 Terminator installation . 38
B.5.5 Device installation . 38
B.5.6 Coding and labelling . 39
B.5.7 Earthing and bonding of equipment and devices and shield cabling . 39
B.5.8 As-implemented cabling documentation . 39
B.6 Installation verification and installation acceptance test . 39
B.6.1 General . 39
B.6.2 Installation verification . 39
B.6.3 Installation acceptance test . 40
B.7 Installation administration . 40
B.8 Installation maintenance and installation troubleshooting . 40
Bibliography . 41

Figure 1 – Standards relationships . 7
Figure A.1 – Topology of CP 19/1 network . 13
Figure A.2 – Network expansion using repeater . 13
Figure A.3 – Structure of cable . 15
Figure A.4 – Dimensions of single port device connector . 17
Figure A.5 – Dimensions of dual ports device connector . 17
Figure A.6 – Dimensions of cable connector . 18
Figure A.7 – Cable connector with inductors . 18
Figure A.8 – Terminator connection in cable connector housing . 19
Figure A.9 – Wiring example . 23
Figure A.10 – Terminator installed in M-II cable connector . 24
Figure A.11 – Division of network segment by changing terminator location . 28
Figure B.1 – Dimensions of IMI device connector . 33
Figure B.2 – Dimensions of IMI cable connector . 34

Table A.1 – Basic network characteristics for balanced cabling not based on Ethernet . 13
Table A.2 – Number of devices and maximum segment length . 14
Table A.3 – Information relevant to copper cable: fixed cables . 15
Table A.4 – Additional cable specifications . 15
Table A.5 – Connectors for copper cabling CPs not based on Ethernet . 16
Table A.6 – Parameters for balanced cables . 22
Table A.7 – Pin assignment and wire colour coding for CP 19/1 connector . 24

---------------------- Page: 9 ----------------------

SIST EN 61784-5-19:2014
– 4 – 61784-5-19 © IEC:2013
Table A.8 – Typical problems in a network with balanced cabling . 27
Table B.1 – Network characteristics for balanced cabling based on Ethernet . 31
Table B.2 – Information relevant to copper cable: fixed cables . 31
Table B.3 – Information relevant to copper cable: cords . 32
Table B.4 – Connectors for balanced cabling CPs based on Ethernet . 33
Table B.5 – Parameters for balanced cables . 37
Table B.6 – Pin assignment and wire colour coding for CP 19/2 connector . 38

---------------------- Page: 10 ----------------------

SIST EN 61784-5-19:2014
61784-5-19 © IEC:2013 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

INDUSTRIAL COMMUNICATION NETWORKS –
PROFILES –

Part 5-19: Installation of fieldbuses –
Installation profiles for CPF 19


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61784-5-19 has been prepared by subcommittee 65C: Industrial
networks, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This standard is to be used in conjunction with IEC 61918:2013.
The text of this standard is based on the following documents:
FDIS Report on voting
65C/738/FDIS 65C/743/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

---------------------- Page: 11 ----------------------

SIST EN 61784-5-19:2014
– 6 – 61784-5-19 © IEC:2013
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of IEC 61784-5 series, under the general title Industrial communication
networks – Profiles – Installation of fieldbuses, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
sidered to be useful for the correct
that it contains colours which are con
understanding of its contents. Users should therefore print this document using a
colour printer.

---------------------- Page: 12 ----------------------

SIST EN 61784-5-19:2014
61784-5-19 © IEC:2013 – 7 –
INTRODUCTION
This International Standard is one of a series produced to facilitate the use of communication
networks in industrial control systems.
IEC 61918:2013 provides the common requirements for the installation of communication
networks in industrial control systems. This installation profile standard provides the
installation profiles of the communication profiles (CP) of a specific communication profile
family (CPF) by stating which requirements of IEC 61918 fully apply and, where necessary, by
supplementing, modifying, or replacing the other requirements (see Figure 1).
For general background on fieldbuses, their profiles, and relationship between the installation
profiles specified in this standard, see IEC 61158-1.
Each CP installation profile is specified in a separate annex of this standard. Each annex is
structured exactly as the reference standard IEC 61918 for the benefit of the persons
representing the roles in the fieldbus installation process as defined in IEC 61918 (planner,
installer, verification personnel, validation personnel, maintenance personnel, administration
personnel). By reading the installation profile in conjunction with IEC 61918, these persons
immediately know which requirements are common for the installation of all CPs and which
are modified or replaced. The conventions used to draft this standard are defined in Clause 5.
The provision of the installation profiles in one standard for each CPF (for example
IEC 61784-5-19 for CPF 19), allows readers to work with standards of a convenient size.


Figure 1 – Standards relationships

---------------------- Page: 13 ----------------------

SIST EN 61784-5-19:2014
– 8 – 61784-5-19 © IEC:2013
INDUSTRIAL COMMUNICATION NETWORKS –
PROFILES –

Part 5-19: Installation of fieldbuses –
Installation profiles for CPF 19



1 Scope
1
This part of IEC 61784 specifies the installation profiles for CPF 19 (MECHATROLINK™ ).
The installation profiles are specified in the annexes. These annexes are read in conjunction
with IEC 61918:2013.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61918:2013, Industrial communication networks – Installation of communication networks
in industrial premises
The normative references of IEC 61918:2013, Clause 2, apply. For profile specific normative
references, see Clause A.2.
3 Terms, definitions and abbreviated terms
For the purposes of this document, the terms, definitions and abbreviated terms given in
IEC 61918:2013, Clause 3, apply. For profile specific terms, definitions and abbreviated terms
see Clauses A.3 and B.3.
4 CPF19: Overview of installation profiles
CPF 19 consists of two Communication Profiles as specified in IEC 61784-1.
The installation requirements for CP 19/1 (MECHATROLINK™-II) are specified in Annex A.
The installation requirements for CP 19/2 (MECHATROLINK™-III) are specified in Annex B.
5 Installation profile conventions
The numbering of the clauses and subclauses in the annexes of this standard corresponds to
the numbering of IEC 61918 main clauses and subclauses.
___________
1
 MECHATROLINK™ is a trade name of YASKAWA ELECTRIC CORPORATION. This information is given for the
convenience of users of this document and does not constitute an endorsement by IEC of the trade names
holder or any of its products. Compliance to this profile does not require use of the trade names. Use of the
trade name MECHATROLINK requires permission of the trade name holder.

---------------------- Page: 14 ----------------------

SIST EN 61784-5-19:2014
61784-5-19 © IEC:2013 – 9 –
The annex clauses and subclauses of this standard supplement, modify, or replace the
respective clauses and subclauses in IEC 61918.
Where there is no corresponding subclause of IEC 61918 in the normative annexes in this
standard, the subclause of IEC 61918 applies without modification.
The annex heading letter represents the installation profile assigned in Clause 4. The annex
heading number shall represent the corresponding numbering of IEC 61918.
EXAMPLE “Suclause B.4.4” in IEC 61784-5-19 means that CP 19/2 specifies the subclause 4.4 of IEC 61918.
All main clauses of IEC 61918 are cited and apply in full unless otherwise stated in each
normative installation profile annex.
If all subclauses of a (sub)clause are omitted, then the corresponding IEC 61918 (sub)clause
applies.
If in a (sub)clause it is written “Not applicable.”, then the corresponding
IEC 61918 (sub)clause does not apply.
If in a (sub)clause it is written “Addition:”, then the corresponding IEC 61918 (sub)clause
applies with the additions written in the profile.
If in a (sub)clause it is written “Replacement:”, then the text provided in the profile replaces
the text of the corresponding IEC 61918 (sub)clause.
NOTE A replacement can also comprise additions.
If in a (sub)clause it is written “Modification:”, then the corresponding IEC 61918 (sub)clause
applies with the modifications written in the profile.
If all (sub)clauses of a (sub)clause are omitted but in this (sub)clause it is written
“(Sub)clause × has addition:” (or “replacement:”) or “(Sub)clause x is not applicable.”, then
(sub)clause x becomes valid as declared and all the other corresponding
IEC 61918 (sub)clauses apply.
6 Conformance to installation profiles
Each installation profile within this standard includes part of IEC 61918:2013. It may also
include defined additional specifications.
2
A statement of compliance to an installation profile of this standard shall be stated as either
3
Compliance to IEC 61784-5-19:2013 for CP 19/n or
Compliance to IEC 61784-5-19 (Ed.1.0) for CP 19/n
where the name within the angle brackets < > is optional and the angle brackets are not to be
included. The n within CP 19/n shall be replaced by the profile number 1 to 2.
NOTE The name can be the name of the profile, for example MECHATROLINK-II or MECHATROLINK-III.
If the name is a trade name then the permission of the trade name holder shall be required.
___________
2
 In accordance with ISO/IEC Directives.
3
The date should not be used
...