SIST EN 300 113-1 V1.6.2:2010

Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land mobile service - Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector - Part 1: Technical characteristics and methods of measurement

The present document covers the technical requirements for radio transmitters and receivers used in stations in the Private Mobile Radio (PMR) service. It applies to use in the land mobile service operating on radio frequencies between 30 MHz and 1 GHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, intended for speech and/or data.
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech. The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated demodulator and decoder. The types of equipment covered by the present document are as follows:
- base station (equipment fitted with an antenna connector, intended for use in a fixed location);
- mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
- and those handportable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector , but fitted with a permanent internal or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input. Handportable equipment without an external or internal RF connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document.

Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Storitev kopenskih mobilnih komunikacij - Radijska oprema za prenos podatkov (oziroma govora), ki uporablja modulacijo s konstantno ali nekonstantno ovojnico in ima antenski priključek - 1. del: Tehnične karakteristike in merilne metode

Pričujoči dokument zajema tehnične zahteve za radijske oddajnike in sprejemnike, ki se uporabljajo v postajah v zasebnih mobilnih radio (PMR) storitvah (PRM). Velja za uporabo pri kopenskih mobilnih storitvah, ki delujejo na radio frekvencah med 30 MHz in 1 GHz, z ločevanjem kanalov 12,5 kHz, 20 kHz in 25 kHz, namenjenim za govor in/ali podatke.
Velja za opremo za neprekinjeno in/ali prekinjeno oddajanje podatkov in/ali digitalni govor. Oprema je sestavljena iz oddajnika in povezanega kodirnika in modulatorja in/ali sprejemnika ter povezanega demodulatorja in dekodirnik. Tipi opreme, ki jo pričujoči dokument zajema, so kot sledi:
- bazna postaja (oprema, opremljena z antenskim priključkom, ki se uporablja na stalni lokaciji);
- mobilna postaja (oprema, opremljena z antenskim priključkom, običajno uporabljena v vozilu ali kot prenosljiva);
- in prenosne ročne postaje:
a) nameščene z antenskim priključkom; ali
b) brez zunanjega antenskega priključka, ampak opremljena s stalnim notranjim ali začasnim zunanjim 50 Ω radiofrekvenčnim (RF) priključkom, ki omogoča dostop do izhoda oddajnika in vhoda sprejemnika. Prenosna ročna oprema, brez zunanjega ali notranjega RF priključka in brez možnosti začasnega notranjega 50 Ω RF priključka, ni zajeta v pričujočem dokumentu.

General Information

• Status: Published
• Publication Date: 18-Jan-2010
• ICS: 33.060.99 - Other equipment for radiocommunications
• ICS: 33.070.01 - Mobile services in general
• ICS: 33.100.01 - Electromagnetic compatibility in general
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 08-Dec-2009
• Due Date: 12-Feb-2010
• Completion Date: 19-Jan-2010
• Ref Project: ETSI EN 300 113-1 V1.6.2 (2009-11) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement

Standards Content (Sample)

European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land mobile service;
Radio equipment intended for the transmission
of data (and/or speech) using constant or non-constant
envelope modulation and having an antenna connector;
Part 1: Technical characteristics and
methods of measurement
2 ETSI EN 300 113-1 V1.6.2 (2009-11)

Reference
REN/ERM-TGDMR-286-1
Keywords
antenna, data, mobile, PMR, radio, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 300 113-1 V1.6.2 (2009-11)
Contents
Intellectual Property Rights . 7
Foreword . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 11
3.3 Abbreviations . 11
4 General . 11
4.1 Presentation of equipment for testing purposes . 11
4.1.1 Choice of model for testing . 12
4.1.1.1 Auxiliary test equipment . 12
4.1.1.2 Declarations by the provider . 12
4.2 Mechanical and electrical design . 12
4.2.1 General . 12
4.2.2 Controls . 12
4.2.3 Transmitter shut-off facility . 12
4.3 Marking . 12
4.4 Testing using bit streams or messages . 13
4.5 Measuring continuous mode equipment . 13
4.6 Measuring discontinuous mode equipment . 13
4.7 Combined full bandwidth analogue speech/full bandwidth digital equipment . 13
4.8 Constant and non-constant envelope modulation . 14
5 Test conditions, power sources and ambient temperatures . 14
5.1 Normal and extreme test conditions . 14
5.2 Test power source . 14
5.3 Normal test conditions . 15
5.3.1 Normal temperature and humidity . 15
5.3.2 Normal test power source . 15
5.3.2.1 Mains voltage . 15
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 15
5.3.2.3 Other power sources . 15
5.4 Extreme test conditions . 15
5.4.1 Extreme temperatures . 15
5.4.2 Extreme test source voltages . 15
5.4.2.1 Mains voltage . 15
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.4.2.3 Power sources using other types of batteries . 16
5.4.2.4 Other power sources . 16
5.5 Procedure for tests at extreme temperatures . 16
5.5.1 Procedure for equipment designed for continuous transmission. 16
5.5.2 Procedure for equipment designed for intermittent transmission . 16
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 17
6 General test conditions . 17
6.1 Arrangements for test signals applied to the receiver input . 17
6.2 Receiver mute or squelch facility . 17
6.3 Normal test signals (wanted and unwanted signals) . 17
6.3.1 Equipment measured as constant envelope angle modulation equipment . 17
6.3.2 Equipment measured as non-constant envelope modulation equipment . 18
6.4 Encoder for receiver measurements . 19
ETSI
4 ETSI EN 300 113-1 V1.6.2 (2009-11)
6.5 Transceiver data interface. 19
6.6 Impedance . 19
6.7 Artificial antenna . 19
6.8 Tests of equipment with a duplex filter . 19
6.9 Facilities for access . 19
6.9.1 Analogue access . 19
6.9.2 Test points for bit stream measurements. 20
6.9.3 Coupling arrangements . 20
6.9.3.1 Arrangements for measurements with continuous bit streams . 20
6.9.3.2 Arrangements for measurements with messages . 20
6.10 Test site and general arrangements for measurements involving the use of radiated fields . 20
6.11 Modes of operation of the transmitter for constant envelope equipment . 21
7 Technical characteristics of the transmitter . 21
7.1 Frequency error . 21
7.1.1 Definition . 21
7.1.2 Method of measurement . 21
7.1.3 Limits . 21
7.2 Transmitter power (conducted) . 22
7.2.1 Definitions . 22
7.2.1.1 Equipment measured as constant envelope angle modulation equipment . 22
7.2.1.2 Equipment measured as non-constant envelope modulation equipment . 22
7.2.2 Method of measurement . 22
7.2.2.1 Equipment measured as constant envelope angle modulation equipment . 22
7.2.2.2 Equipment measured as non-constant envelope modulation equipment . 23
7.2.3 Limits . 23
7.3 Maximum Effective radiated power . 23
7.3.1 Definition . 23
7.3.1.1 Equipment measured as constant envelope angle modulation equipment . 23
7.3.1.2 Equipment measured as non-constant envelope modulation equipment . 24
7.3.2 Methods of measurement . 24
7.3.2.1 Equipment measured as constant envelope angle modulation equipment . 25
7.3.2.2 Equipment measured as non-constant envelope modulation equipment . 26
7.3.3 Limits . 27
7.4 Adjacent channel power . 28
7.4.1 Definition . 28
7.4.2 Method of measurement . 28
7.4.3 Limits . 29
7.5 Unwanted emissions in the spurious domain. 29
7.5.1 Definition . 29
7.5.2 Method of measuring the power level . 30
7.5.2.1 Equipment measured as constant envelope angle modulation equipment . 30
7.5.2.2 Equipment measured as non-constant envelope modulation equipment . 30
7.5.3 Method of measuring the effective radiated power . 31
7.5.3.1 Equipment measured as constant envelope angle modulation equipment . 31
7.5.3.2 Equipment measured as non-constant envelope modulation equipment . 32
7.5.4 Limits . 33
7.6 Intermodulation attenuation. 34
7.6.1 Definition . 34
7.6.2 Method of measurement . 35
7.6.3 Limits . 35
7.7 Transmitter attack time . 36
7.7.1 Definition . 36
7.7.2 Method of measurement . 36
7.7.3 Limit . 37
7.8 Transmitter release time . 37
7.8.1 Definition . 37
7.8.2 Method of measurement . 37
7.8.3 Limits . 37
7.9 Transient behaviour of the transmitter . 38
7.9.1 Definitions . 38
7.9.2 Timings, frequencies and powers . 40
ETSI
5 ETSI EN 300 113-1 V1.6.2 (2009-11)
7.9.3 Methods of measurement . 43
7.9.3.1 Time domain measurements of power and frequency . 43
7.9.3.2 Test arrangement and characteristics of the FM modulation meter . 44
7.9.3.3 Adjacent channel transient power measurements . 44
7.9.3.3.1 Definition. 44
7.9.3.3.2 Measurement method for constant envelope angle modulation equipment . 44
7.9.3.3.3 Measurement method for non-constant envelope modulation equipment . 45
7.9.3.4 Characteristics of the adjacent channel transient power measuring device . 46
7.9.4 Limits . 46
7.9.4.1 Time domain analysis of power and frequency . 47
7.9.4.2 Adjacent and alternate channel transient power . 47
7.9.4.2.1 Equipment measured as constant envelope angle modulation equipment . 47
7.9.4.2.2 Equipment measured as non-constant envelope modulation equipment . 47
8 Methods of measurement for receiver parameters . 48
8.1 Maximum usable sensitivity (digital, conducted) . 48
8.1.1 Definition . 48
8.1.2 Method of measurement . 48
8.1.2.1 Method of measurement with continuous bit streams . 48
8.1.2.2 Method of measurement with messages . 49
8.1.3 Limits . 50
8.2 Average usable sensitivity (digital, field strength) . 50
8.2.1 Definition . 50
8.2.2 Method of measurement . 50
8.2.3 Limits . 50
8.3 Level of the wanted signal for the degradation measurements (data or messages) . 50
8.4 Error behaviour at high input levels . 50
8.4.1 Definition . 50
8.4.2 Method of measurement . 51
8.4.2.1 Method of measurement with continuous bit streams . 51
8.4.2.2 Method of measurement with messages . 51
8.4.3 Limits . 52
8.5 Co-channel rejection. 52
8.5.1 Definition . 52
8.5.2 Method of measurement . 52
8.5.2.1 Method of measurement with continuous bit streams . 52
8.5.2.2 Method of measurement with messages . 53
8.5.3 Limits . 54
8.6 Adjacent channel selectivity . 54
8.6.1 Definition . 54
8.6.2 Method of measurement . 55
8.6.2.1 Method of measurement with continuous bit streams . 55
8.6.2.2 Method of measurement with messages . 56
8.6.3 Limits . 57
8.7 Spurious response rejection . 57
8.7.1 Definition . 57
8.7.2 Introduction to the method of measurement . 57
8.7.3 Method of search over the "limited frequency range" . 58
8.7.4 Method of measurement with continuous bit streams . 59
8.7.5 Method of measurement with messages . 60
8.7.6 Limits . 60
8.8 Intermodulation response rejection . 61
8.8.1 Definition . 61
8.8.2 Method of measurement . 61
8.8.2.1 Method of measurement with continuous bit streams . 61
8.8.2.2 Method of measurement with messages . 62
8.8.3 Limits . 63
8.9 Blocking or desensitization . 63
8.9.1 Definition . 63
8.9.2 Method of measurement . 64
8.9.2.1 Method of measurement with continuous bit streams . 64
8.9.2.2 Method of measurement with messages . 65
ETSI
6 ETSI EN 300 113-1 V1.6.2 (2009-11)
8.9.3 Limits . 66
8.10 Spurious radiations . 66
8.10.1 Definition . 66
8.10.2 Method of measuring the power level . 66
8.10.3 Method of measuring the effective radiated power . 67
8.10.4 Limits . 68
9 Duplex operation . 69
9.1 Receiver desensitization (with simultaneous transmission and reception) . 69
9.1.1 Definition . 69
9.1.2 Desensitization measured with continuous bit streams . 69
9.1.2.1 Method of measurement when the equipment has a duplex filter . 69
9.1.2.2 Method of measurement when the equipment has to operate with two antennas . 70
9.1.3 Desensitization measured with messages . 72
9.1.3.1 Method of measurement when the equipment has a duplex filter . 72
9.1.3.2 Method of measurement when the equipment has to operate with two antennas . 73
9.1.4 Limits . 74
9.2 Receiver spurious response rejection (with simultaneous transmission and reception) . 74
9.2.1 Definition . 74
9.2.2 Method of measurement . 74
9.2.3 Limits . 75
10 Measurement uncertainty . 75
Annex A (normative): Radiated measurement . 77
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 77
A.1.1 Anechoic chamber . 77
A.1.2 Anechoic chamber with a conductive ground plane . 78
A.1.3 Open Area Test Site (OATS) . 79
A.1.4 Test antenna . 80
A.1.5 Substitution antenna . 81
A.1.6 Measuring antenna . 81
A.2 Guidance on the use of radiation test sites . 81
A.2.1 Verification of the test site . 81
A.2.2 Preparation of the EUT . 81
A.2.3 Power supplies to the EUT . 81
A.2.4 Volume control setting for analogue speech tests . 82
A.2.5 Range length . 82
A.2.6 Site preparation . 83
A.3 Coupling of signals . 83
A.3.1 General . 83
A.3.2 Data Signals. 83
A.3.3 Speech and analogue signals . 83
A.3.3.1 Acoustic coupler description. 84
A.3.3.2 Calibration . 84
Annex B (normative): Specification for some particular measurement arrangements . 85
B.1 Power measuring receiver specification . 85
B.1.1 IF filter . 85
B.1.2 Attenuation indicator . 86
B.1.3 RMS value indicator . 86
B.1.4 Oscillator and amplifier . 86
B.2 Spectrum analyser specification . 87
B.3 Integrating and power summing device . 87
Annex C (informative): Bibliography . 88
History . 89

ETSI
7 ETSI EN 300 113-1 V1.6.2 (2009-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document is part 1 of a multi-part deliverable covering the Electromagnetic compatibility and Radio
spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech)
using constant or non-constant envelope modulation and having an antenna connector, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".

Proposed national transposition dates
Date of latest announcement of this EN (doa): 28 February 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 August 2010
Date of withdrawal of any conflicting National Standard (dow): 31 August 2010

ETSI
8 ETSI EN 300 113-1 V1.6.2 (2009-11)
1 Scope
The present document covers the technical requirements for radio transmitters and receivers used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 1 GHz, with channel
separations of 12,5 kHz, 20 kHz and 25 kHz, intended for speech and/or data.
Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands
Transmit 30 MHz to 1 000 MHz
Receive 30 MHz to 1 000 MHz
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech.
The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated
demodulator and decoder. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• and those handportable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector , but fitted with a permanent internal or a temporary internal 50 Ω
Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input.
Handportable equipment without an external or internal RF connector and without the possibility of having a temporary
internal 50 Ω RF connector is not covered by the present document.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
ETSI
9 ETSI EN 300 113-1 V1.6.2 (2009-11)
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 300 086-1 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land Mobile Service; Radio equipment with an internal or external RF connector intended
primarily for analogue speech; Part 1: Technical characteristics and methods of measurement".
[2] ETSI EN 300 390-1 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land Mobile Service; Radio equipment intended for the transmission of data (and speech) and
using an integral antenna; Part 1: Technical characteristics and test conditions".
[3] ETSI TR 100 028 (V1.4.1) (all parts): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[4] ITU-T Recommendation O.153: "Basic parameters for the measurement of error performance at
bit rates below the primary rate".
[5] ANSI C63.5 (2004): "American National Standard for Electromagnetic Compatibility-Radiated
Emission Measurements in Electromagnetic Interference (EMI) Control-Calibration of Antennas
(9 kHz to 40 GHz)".
[6] IEC 60489-3 (1988): "Methods of measurement for radio equipment used in the mobiles services.
Part 3: Receivers for A3E or F3E emissions".
[7] CEPT/ERC/REC 74-01E: "Unwanted emissions in the spurious domain". (Siófok 1998, Nice
1999, Sesimbra 2002 Hradec Kralove 2005).
[8] ETSI EN 300 793 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land mobile service; Presentation of equipment for type testing".
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] ETSI TR 102 273 (V1.2.1) (all parts): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the
corresponding measurement uncertainties".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
50 Ω: 50 ohm non-reactive impedance
adjacent channels: channel offset from the wanted channel by the channel spacing
alternate channels: two channels offset from the wanted channel by double the channel spacin
...

SLOVENSKI STANDARD
01-februar-2010
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP(50
6WRULWHYNRSHQVNLKPRELOQLKNRPXQLNDFLM5DGLMVNDRSUHPD]DSUHQRVSRGDWNRY
R]LURPDJRYRUDNLXSRUDEOMDPRGXODFLMRVNRQVWDQWQRDOLQHNRQVWDQWQRRYRMQLFR
LQLPDDQWHQVNLSULNOMXþHNGHO7HKQLþQHNDUDNWHULVWLNHLQPHULOQHPHWRGH
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land mobile service -
Radio equipment intended for the transmission of data (and/or speech) using constant or
non-constant envelope modulation and having an antenna connector - Part 1: Technical
characteristics and methods of measurement
Ta slovenski standard je istoveten z: EN 300 113-1 Version 1.6.2
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land mobile service;
Radio equipment intended for the transmission
of data (and/or speech) using constant or non-constant
envelope modulation and having an antenna connector;
Part 1: Technical characteristics and
methods of measurement
2 ETSI EN 300 113-1 V1.6.2 (2009-11)

Reference
REN/ERM-TGDMR-286-1
Keywords
antenna, data, mobile, PMR, radio, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 300 113-1 V1.6.2 (2009-11)
Contents
Intellectual Property Rights . 7
Foreword . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 11
3.3 Abbreviations . 11
4 General . 11
4.1 Presentation of equipment for testing purposes . 11
4.1.1 Choice of model for testing . 12
4.1.1.1 Auxiliary test equipment . 12
4.1.1.2 Declarations by the provider . 12
4.2 Mechanical and electrical design . 12
4.2.1 General . 12
4.2.2 Controls . 12
4.2.3 Transmitter shut-off facility . 12
4.3 Marking . 12
4.4 Testing using bit streams or messages . 13
4.5 Measuring continuous mode equipment . 13
4.6 Measuring discontinuous mode equipment . 13
4.7 Combined full bandwidth analogue speech/full bandwidth digital equipment . 13
4.8 Constant and non-constant envelope modulation . 14
5 Test conditions, power sources and ambient temperatures . 14
5.1 Normal and extreme test conditions . 14
5.2 Test power source . 14
5.3 Normal test conditions . 15
5.3.1 Normal temperature and humidity . 15
5.3.2 Normal test power source . 15
5.3.2.1 Mains voltage . 15
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 15
5.3.2.3 Other power sources . 15
5.4 Extreme test conditions . 15
5.4.1 Extreme temperatures . 15
5.4.2 Extreme test source voltages . 15
5.4.2.1 Mains voltage . 15
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 16
5.4.2.3 Power sources using other types of batteries . 16
5.4.2.4 Other power sources . 16
5.5 Procedure for tests at extreme temperatures . 16
5.5.1 Procedure for equipment designed for continuous transmission. 16
5.5.2 Procedure for equipment designed for intermittent transmission . 16
5.5.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 17
6 General test conditions . 17
6.1 Arrangements for test signals applied to the receiver input . 17
6.2 Receiver mute or squelch facility . 17
6.3 Normal test signals (wanted and unwanted signals) . 17
6.3.1 Equipment measured as constant envelope angle modulation equipment . 17
6.3.2 Equipment measured as non-constant envelope modulation equipment . 18
6.4 Encoder for receiver measurements . 19
ETSI
4 ETSI EN 300 113-1 V1.6.2 (2009-11)
6.5 Transceiver data interface. 19
6.6 Impedance . 19
6.7 Artificial antenna . 19
6.8 Tests of equipment with a duplex filter . 19
6.9 Facilities for access . 19
6.9.1 Analogue access . 19
6.9.2 Test points for bit stream measurements. 20
6.9.3 Coupling arrangements . 20
6.9.3.1 Arrangements for measurements with continuous bit streams . 20
6.9.3.2 Arrangements for measurements with messages . 20
6.10 Test site and general arrangements for measurements involving the use of radiated fields . 20
6.11 Modes of operation of the transmitter for constant envelope equipment . 21
7 Technical characteristics of the transmitter . 21
7.1 Frequency error . 21
7.1.1 Definition . 21
7.1.2 Method of measurement . 21
7.1.3 Limits . 21
7.2 Transmitter power (conducted) . 22
7.2.1 Definitions . 22
7.2.1.1 Equipment measured as constant envelope angle modulation equipment . 22
7.2.1.2 Equipment measured as non-constant envelope modulation equipment . 22
7.2.2 Method of measurement . 22
7.2.2.1 Equipment measured as constant envelope angle modulation equipment . 22
7.2.2.2 Equipment measured as non-constant envelope modulation equipment . 23
7.2.3 Limits . 23
7.3 Maximum Effective radiated power . 23
7.3.1 Definition . 23
7.3.1.1 Equipment measured as constant envelope angle modulation equipment . 23
7.3.1.2 Equipment measured as non-constant envelope modulation equipment . 24
7.3.2 Methods of measurement . 24
7.3.2.1 Equipment measured as constant envelope angle modulation equipment . 25
7.3.2.2 Equipment measured as non-constant envelope modulation equipment . 26
7.3.3 Limits . 27
7.4 Adjacent channel power . 28
7.4.1 Definition . 28
7.4.2 Method of measurement . 28
7.4.3 Limits . 29
7.5 Unwanted emissions in the spurious domain. 29
7.5.1 Definition . 29
7.5.2 Method of measuring the power level . 30
7.5.2.1 Equipment measured as constant envelope angle modulation equipment . 30
7.5.2.2 Equipment measured as non-constant envelope modulation equipment . 30
7.5.3 Method of measuring the effective radiated power . 31
7.5.3.1 Equipment measured as constant envelope angle modulation equipment . 31
7.5.3.2 Equipment measured as non-constant envelope modulation equipment . 32
7.5.4 Limits . 33
7.6 Intermodulation attenuation. 34
7.6.1 Definition . 34
7.6.2 Method of measurement . 35
7.6.3 Limits . 35
7.7 Transmitter attack time . 36
7.7.1 Definition . 36
7.7.2 Method of measurement . 36
7.7.3 Limit . 37
7.8 Transmitter release time . 37
7.8.1 Definition . 37
7.8.2 Method of measurement . 37
7.8.3 Limits . 37
7.9 Transient behaviour of the transmitter . 38
7.9.1 Definitions . 38
7.9.2 Timings, frequencies and powers . 40
ETSI
5 ETSI EN 300 113-1 V1.6.2 (2009-11)
7.9.3 Methods of measurement . 43
7.9.3.1 Time domain measurements of power and frequency . 43
7.9.3.2 Test arrangement and characteristics of the FM modulation meter . 44
7.9.3.3 Adjacent channel transient power measurements . 44
7.9.3.3.1 Definition. 44
7.9.3.3.2 Measurement method for constant envelope angle modulation equipment . 44
7.9.3.3.3 Measurement method for non-constant envelope modulation equipment . 45
7.9.3.4 Characteristics of the adjacent channel transient power measuring device . 46
7.9.4 Limits . 46
7.9.4.1 Time domain analysis of power and frequency . 47
7.9.4.2 Adjacent and alternate channel transient power . 47
7.9.4.2.1 Equipment measured as constant envelope angle modulation equipment . 47
7.9.4.2.2 Equipment measured as non-constant envelope modulation equipment . 47
8 Methods of measurement for receiver parameters . 48
8.1 Maximum usable sensitivity (digital, conducted) . 48
8.1.1 Definition . 48
8.1.2 Method of measurement . 48
8.1.2.1 Method of measurement with continuous bit streams . 48
8.1.2.2 Method of measurement with messages . 49
8.1.3 Limits . 50
8.2 Average usable sensitivity (digital, field strength) . 50
8.2.1 Definition . 50
8.2.2 Method of measurement . 50
8.2.3 Limits . 50
8.3 Level of the wanted signal for the degradation measurements (data or messages) . 50
8.4 Error behaviour at high input levels . 50
8.4.1 Definition . 50
8.4.2 Method of measurement . 51
8.4.2.1 Method of measurement with continuous bit streams . 51
8.4.2.2 Method of measurement with messages . 51
8.4.3 Limits . 52
8.5 Co-channel rejection. 52
8.5.1 Definition . 52
8.5.2 Method of measurement . 52
8.5.2.1 Method of measurement with continuous bit streams . 52
8.5.2.2 Method of measurement with messages . 53
8.5.3 Limits . 54
8.6 Adjacent channel selectivity . 54
8.6.1 Definition . 54
8.6.2 Method of measurement . 55
8.6.2.1 Method of measurement with continuous bit streams . 55
8.6.2.2 Method of measurement with messages . 56
8.6.3 Limits . 57
8.7 Spurious response rejection . 57
8.7.1 Definition . 57
8.7.2 Introduction to the method of measurement . 57
8.7.3 Method of search over the "limited frequency range" . 58
8.7.4 Method of measurement with continuous bit streams . 59
8.7.5 Method of measurement with messages . 60
8.7.6 Limits . 60
8.8 Intermodulation response rejection . 61
8.8.1 Definition . 61
8.8.2 Method of measurement . 61
8.8.2.1 Method of measurement with continuous bit streams . 61
8.8.2.2 Method of measurement with messages . 62
8.8.3 Limits . 63
8.9 Blocking or desensitization . 63
8.9.1 Definition . 63
8.9.2 Method of measurement . 64
8.9.2.1 Method of measurement with continuous bit streams . 64
8.9.2.2 Method of measurement with messages . 65
ETSI
6 ETSI EN 300 113-1 V1.6.2 (2009-11)
8.9.3 Limits . 66
8.10 Spurious radiations . 66
8.10.1 Definition . 66
8.10.2 Method of measuring the power level . 66
8.10.3 Method of measuring the effective radiated power . 67
8.10.4 Limits . 68
9 Duplex operation . 69
9.1 Receiver desensitization (with simultaneous transmission and reception) . 69
9.1.1 Definition . 69
9.1.2 Desensitization measured with continuous bit streams . 69
9.1.2.1 Method of measurement when the equipment has a duplex filter . 69
9.1.2.2 Method of measurement when the equipment has to operate with two antennas . 70
9.1.3 Desensitization measured with messages . 72
9.1.3.1 Method of measurement when the equipment has a duplex filter . 72
9.1.3.2 Method of measurement when the equipment has to operate with two antennas . 73
9.1.4 Limits . 74
9.2 Receiver spurious response rejection (with simultaneous transmission and reception) . 74
9.2.1 Definition . 74
9.2.2 Method of measurement . 74
9.2.3 Limits . 75
10 Measurement uncertainty . 75
Annex A (normative): Radiated measurement . 77
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 77
A.1.1 Anechoic chamber . 77
A.1.2 Anechoic chamber with a conductive ground plane . 78
A.1.3 Open Area Test Site (OATS) . 79
A.1.4 Test antenna . 80
A.1.5 Substitution antenna . 81
A.1.6 Measuring antenna . 81
A.2 Guidance on the use of radiation test sites . 81
A.2.1 Verification of the test site . 81
A.2.2 Preparation of the EUT . 81
A.2.3 Power supplies to the EUT . 81
A.2.4 Volume control setting for analogue speech tests . 82
A.2.5 Range length . 82
A.2.6 Site preparation . 83
A.3 Coupling of signals . 83
A.3.1 General . 83
A.3.2 Data Signals. 83
A.3.3 Speech and analogue signals . 83
A.3.3.1 Acoustic coupler description. 84
A.3.3.2 Calibration . 84
Annex B (normative): Specification for some particular measurement arrangements . 85
B.1 Power measuring receiver specification . 85
B.1.1 IF filter . 85
B.1.2 Attenuation indicator . 86
B.1.3 RMS value indicator . 86
B.1.4 Oscillator and amplifier . 86
B.2 Spectrum analyser specification . 87
B.3 Integrating and power summing device . 87
Annex C (informative): Bibliography . 88
History . 89

ETSI
7 ETSI EN 300 113-1 V1.6.2 (2009-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document is part 1 of a multi-part deliverable covering the Electromagnetic compatibility and Radio
spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech)
using constant or non-constant envelope modulation and having an antenna connector, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".

Proposed national transposition dates
Date of latest announcement of this EN (doa): 28 February 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 August 2010
Date of withdrawal of any conflicting National Standard (dow): 31 August 2010

ETSI
8 ETSI EN 300 113-1 V1.6.2 (2009-11)
1 Scope
The present document covers the technical requirements for radio transmitters and receivers used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 1 GHz, with channel
separations of 12,5 kHz, 20 kHz and 25 kHz, intended for speech and/or data.
Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands
Transmit 30 MHz to 1 000 MHz
Receive 30 MHz to 1 000 MHz
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech.
The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated
demodulator and decoder. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• and those handportable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector , but fitted with a permanent internal or a temporary internal 50 Ω
Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input.
Handportable equipment without an external or internal RF connector and without the possibility of having a temporary
internal 50 Ω RF connector is not covered by the present document.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
ETSI
9 ETSI EN 300 113-1 V1.6.2 (2009-11)
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 300 086-1 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land Mobile Service; Radio equipment with an internal or external RF connector intended
primarily for analogue speech; Part 1: Technical characteristics and methods of measurement".
[2] ETSI EN 300 390-1 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Land Mobile Service; Radio equipment intended for the transmission of data (and speech) and
using an integral antenna; Part 1: Technical characteristics and test conditions".
[3] ETSI TR 100 028 (V1.4.1) (all parts): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[4] ITU-T Recommendation O.153: "Basic parameters for the measurement of error p
...