Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels

This document specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from non-alloy quality and special steels and supplied in the normalized, normalized and tempered, quenched and tempered or annealed condition
The majority of steels listed in this document, with properties in the quenched and tempered condition up to 160 mm thickness, are identical to steels specified in EN 10083-1 and EN 10083-2 and more extensive information on hardenability and technological properties is given in these standards.
General Information on technical delivery conditions is given in EN 10021.

Freiformschmiedestücke aus Stahl für allgemeine Verwendung - Teil 2: Unlegierte Qualitäts- und Edelstähle

Dieser Teil dieser Europäischen Norm legt die allgemeinen technischen Lieferbedingungen für Freiformschmiedestücke, geschmiedete Stäbe und Erzeugnisse, die vorgeschmiedet und in Ringwalzwerken fertig umgeformt werden, fest, Sie sind für allgemeine Verwendung bestimmt.
Die meisten Stähle, die in diesem Dokument mit Eigenschaften im vergüteten Zustand für bis zu 160 mm Dicke aufgeführt sind, sind mit Stählen identisch, die in EN ISO 683-1 und EN ISO 683-2 festgelegt sind. Umfassendere Angaben über die Härtbarkeit und technologische Eigenschaften werden in jenen Normen gemacht.
Allgemeine Angaben über die technischen Lieferbedingungen enthält EN 10021.

Pièces forgées en acier pour usage général - Partie 2: Aciers de qualité non alliés et aciers spéciaux

Le présent document spécifie les exigences techniques de livraison des pièces obtenues par forgeage libre, des barres forgées et des produits pré-forgés et finis par laminage circulaire, fabriqués en acier spécial et en acier de qualité non allié et livrés à l'état normalisé, normalisé et revenu, trempé et revenu ou recuit.
La majorité des aciers cités le présent document, avec des caractéristiques à l'état trempé et revenu jusqu'à une épaisseur de 160 mm, sont identiques aux aciers spécifiés dans l'EN ISO 683-1 et l'EN ISO 683-2 et des informations plus complètes sur la trempabilité et les propriétés technologiques sont données dans ces normes.
Les informations générales sur les conditions techniques de livraison sont données dans l'EN 10021.

Prosto kovani jekleni izkovki za splošno tehnično uporabo - 2. del: Nelegirana kakovostna in plemenita jekla

General Information

Status
Not Published
Public Enquiry End Date
27-Jan-2021
Technical Committee
Current Stage
5020 - Formal vote (FV) (Adopted Project)
Start Date
24-Nov-2021
Due Date
12-Jan-2022

RELATIONS

Buy Standard

Draft
oSIST prEN 10250-2:2021
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN 10250-2:2021
01-januar-2021
Prosto kovani jekleni izkovki za splošno tehnično uporabo - 2. del: Nelegirana
kakovostna in plemenita jekla

Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and

special steels
Freiformschmiedestücke aus Stahl für allgemeine Verwendung - Teil 2: Unlegierte
Qualitäts- und Edelstähle

Pièces forgées en acier pour usage général - Partie 2: Aciers de qualité non alliés et

aciers spéciaux
Ta slovenski standard je istoveten z: prEN 10250-2
ICS:
77.140.20 Visokokakovostna jekla Stainless steels
77.140.45 Nelegirana jekla Non-alloyed steels
77.140.85 Železni in jekleni kovani Iron and steel forgings
izdelki
oSIST prEN 10250-2:2021 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 10250-2:2021
---------------------- Page: 2 ----------------------
oSIST prEN 10250-2:2021
DRAFT
EUROPEAN STANDARD
prEN 10250-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2020
ICS 77.140.45; 77.140.85 Will supersede EN 10250-2:1999
English Version
Open die steel forgings for general engineering purposes -
Part 2: Non-alloy quality and special steels

Pièces forgées en acier pour usage général - Partie 2: Freiformschmiedestücke aus Stahl für allgemeine

Aciers de qualité non alliés et aciers spéciaux Verwendung - Teil 2: Unlegierte Qualitäts- und

Edelstähle

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee

CEN/TC 459/SC 11.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10250-2:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10250-2:2021
prEN 10250-2:2020 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

1 Scope .................................................................................................................................................................... 4

2 Normative references .................................................................................................................................... 4

3 Terms and definitions ................................................................................................................................... 4

4 Chemical composition ................................................................................................................................... 4

4.1 Cast analysis ...................................................................................................................................................... 4

4.2 Product analysis .............................................................................................................................................. 4

5 Heat treatment ................................................................................................................................................. 4

6 Mechanical properties ................................................................................................................................... 5

6.1 Forgings in the normalized, normalized and tempered, and quenched and tempered

condition ............................................................................................................................................................ 5

6.2 Forgings in the annealed condition (Steels C45, C55 and C60) ...................................................... 5

Annex A (informative) Heat treatment [4] ............................................................................................................ 9

Bibliography ................................................................................................................................................................. 10

---------------------- Page: 4 ----------------------
oSIST prEN 10250-2:2021
prEN 10250-2:2020 (E)
European foreword

This document (prEN 10250-2:2020) has been prepared by Technical Committee CEN/TC 459 “Steel

castings and forgings”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10250-2:1999.

In comparison with the previous edition, the following technical modifications have been made:

— updating of normative references;

— deletion of previous Table 2 - Permissible deviations between the product analysis and the limiting

values given in Table 1 for the cast analysis;
— deletion of C 22 steel grade from all the tables.

EN 10250, Open die steel forgings for general engineering purposes, consists of the following parts:

— Part 1: General requirements;
— Part 2: Non-alloy quality and special steels;
— Part 3: Alloy special steels;
— Part 4: Stainless steels.
---------------------- Page: 5 ----------------------
oSIST prEN 10250-2:2021
prEN 10250-2:2020 (E)
1 Scope

This document specifies the technical delivery requirements for open die forgings, forged bars and

products pre-forged and finished in ring rolling mills, manufactured from non-alloy quality and special

steels and supplied in the normalized, normalized and tempered, quenched and tempered or annealed

condition

The majority of steels listed in this document, with properties in the quenched and tempered condition

up to 160 mm thickness, are identical to steels specified in EN ISO 683-1 and EN ISO 683-2 and more

extensive information on hardenability and technological properties is given in these standards.

General information on technical delivery conditions is given in EN 10021.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

prEN 10250-1:2020, Open die steel forgings for general engineering purposes - Part 1: General

requirements

EN ISO 683-1:2018, Heat-treatable steels, alloy steels and free-cutting steels - Part 1: Non-alloy steels for

quenching and tempering (ISO 683-1:2016)

EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1)

3 Terms and definitions
No terms and definitions are listed in this document.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
4 Chemical composition
4.1 Cast analysis

The chemical composition of the steel shall be determined by cast analysis and shall conform to the

analysis given in Table 1 (see A.7 and A.8 of prEN 10250-1:2020).

Measures should be taken to prevent the addition from the scrap, or other material used in the

manufacture of the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.