SIST EN 60034-12:2002
(Main)Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors (IEC 60034-12:2002)
Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors (IEC 60034-12:2002)
Specifies four standard designs of starting performance for three-phase motors, from 0.4 kW up to 630 kW for direct on-line or star-delta starting and rated on the basis of duty-type S-1 (maximum continuous rating). Also covers dual voltage motors in so far as the flux saturation level is the same for both voltages.
Drehende elektrische Maschinen - Teil 12: Anlaufverhalten von Drehstrommotoren mit Käfigläufer ausgenommen polumschaltbare Motoren (IEC 60034-12:2002)
Machines électriques tournantes - Partie 12: Caractéristiques de démarrage des moteurs triphasés à induction à cage à une seule vitesse (CEI 60034-12:2002)
Spécifie quatre conceptions normales des caractéristiques de démarrage de moteurs triphasés de 0,4 kW à 630 kW pour démarrage direct ou en étoile-triangle dimensionnés pour le service type S-1 (service maximal continu). S'applique également aux moteurs bi-tension dans la mesure où le niveau de saturation du flux est le même pour les deux tensions.
Električni rotacijski stroji - 12. del: Zagonske lastnosti enohitrostnih trifaznih motorjev z indukcijsko kletko (IEC 60034-12:2002)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60034-12:2002
01-september-2002
1DGRPHãþD
SIST EN 60034-12:1999
SIST EN 60034-12:1999/A2:1999
(OHNWULþQLURWDFLMVNLVWURMLGHO =DJRQVNHODVWQRVWLHQRKLWURVWQLKWULID]QLK
PRWRUMHY]LQGXNFLMVNRNOHWNR ,(&
Rotating electrical machines - Part 12: Starting performance of single-speed three-phase
cage induction motors (IEC 60034-12:2002)
Drehende elektrische Maschinen - Teil 12: Anlaufverhalten von Drehstrommotoren mit
Käfigläufer ausgenommen polumschaltbare Motoren (IEC 60034-12:2002)
Machines électriques tournantes - Partie 12: Caractéristiques de démarrage des moteurs
triphasés à induction à cage à une seule vitesse (CEI 60034-12:2002)
Ta slovenski standard je istoveten z: EN 60034-12:2002
ICS:
29.160.30 Motorji Motors
SIST EN 60034-12:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60034-12:2002
---------------------- Page: 2 ----------------------
SIST EN 60034-12:2002
EUROPEAN STANDARD EN 60034-12
NORME EUROPÉENNE
EUROPÄISCHE NORM May 2002
ICS 29.160.30 Supersedes EN 60034-12:1995 + A2:1995 + A11:1999
English version
Rotating electrical machines
Part 12: Starting performance of single-speed
three-phase cage induction motors
(IEC 60034-12:2002)
Machines électriques tournantes Drehende elektrische Maschinen
Partie 12: Caractéristiques de démarrage Teil 12: Anlaufverhalten
des moteurs triphasés à induction von Drehstrommotoren
à cage à une seule vitesse mit Käfigläufer ausgenommen
(CEI 60034-12:2002) polumschaltbare Motoren
(IEC 60034-12:2002)
This European Standard was approved by CENELEC on 2002-05-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,
Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60034-12:2002 E
---------------------- Page: 3 ----------------------
SIST EN 60034-12:2002
EN 60034-12:2002 - 2 -
Foreword
The text of document 2/1187/FDIS, future edition 2 of IEC 60034-12, prepared by IEC TC 2, Rotating
machinery, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60034-12 on 2002-05-01.
This European Standard supersedes EN 60034-12:1995 + A2:1995 + A11:1999.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2003-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2005-05-01
Annexes designated "normative" are part of the body of the standard.
In this standard, annex ZA is normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60034-12:2002 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 4 ----------------------
SIST EN 60034-12:2002
- 3 - EN 60034-12:2002
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60034-1 - Rotating electrical machines EN 60034-1 1998
(mod) Part 1: Rating and performance + corr. February 1993
1)
IEC 60079-0 - Electrical apparatus for explosive gas--
atmospheres
Part 0: General requirements
1)
IEC 60079-7 - Part 7: Increased safety "e" - -
1)
Undated reference.
2)
Valid edition at date of issue.
---------------------- Page: 5 ----------------------
SIST EN 60034-12:2002
---------------------- Page: 6 ----------------------
SIST EN 60034-12:2002
NORME CEI
INTERNATIONALE IEC
60034-12
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
2002-04
Machines électriques tournantes –
Partie 12:
Caractéristiques de démarrage des moteurs
triphasés à induction à cage à une seule vitesse
Rotating electrical machines –
Part 12:
Starting performance of single-speed
three-phase cage induction motors
IEC 2002 Droits de reproduction réservés Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
L
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
Международная Электротехническая Комиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue
---------------------- Page: 7 ----------------------
SIST EN 60034-12:2002
60034-12 © IEC:2002 – 3 –
CONTENTS
FOREWORD.5
1 Scope.7
2 Normative references .7
3 Definitions .9
4 Symbols .9
5 Designation .11
5.1 General .11
5.2 Design N .11
5.3 Design NY.11
5.4 Design H .11
5.5 Design HY.11
6 Design N requirements .11
6.1 Torque characteristics .11
6.2 Locked rotor apparent power .11
6.3 Starting requirements .13
7 Design NY starting requirements .13
8 Design H requirements .13
8.1 Starting torque .13
8.2 Locked rotor apparent power .13
8.3 Starting requirements .13
9 Design HY requirements starting requirements .15
Table 1 – Minimum value of torques for design N.15
Table 2 – Maximum value of locked rotor apparent power for design N and H.15
Table 3 – External inertia (J) .17
Table 4 – Minimum values of torques for design H .19
Table 5 – Minimum value of torques for design N-e starting performance
for motors with type of protection 'e'.19
Table 6 – Maximum value of locked rotor apparent power
for motors with type of protection 'e'.21
Table 7 – External inertia (J) for motors with type of protection 'e'.21
---------------------- Page: 8 ----------------------
SIST EN 60034-12:2002
60034-12 © IEC:2002 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ROTATING ELECTRICAL MACHINES –
Part 12: Starting performance of single-speed
three-phase cage induction motors
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the
two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60034-12 has been prepared by IEC technical committee 2:
Rotating machinery.
This second edition cancels and replaces the first edition published in 1980, its Amendment 1
(1992) and its Amendment 2 (1995). This second edition constitutes a technical revision.
The text of this standard is based on the following documents:
FDIS Report on voting
2/1187/FDIS 2/1199/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
The committee has decided that the contents of this publication will remain unchanged until
2005. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
---------------------- Page: 9 ----------------------
SIST EN 60034-12:2002
60034-12 © IEC:2002 – 7 –
ROTATING ELECTRICAL MACHINES –
Part 12: Starting performance of single-speed
three-phase cage induction motors
1 Scope
This International standard specifies the parameters for four designs of starting performance
of single-speed three-phase 50 Hz or 60 Hz cage induction motors in accordance with
IEC 60034-1 that:
• have a rated voltage up to 1 000 V;
• are intended for direct-on-line or star-delta starting;
• are rated on the basis of duty type S1;
• are constructed to any degree of protection.
The standard also applies to dual voltage motors provided that the flux saturation level is the
same for both voltages and to motors having type of protection 'e – increased safety' with
temperature classes T1 to T3 complying with IEC 60079-0 and IEC 60079-7
NOTE 1 It is not expected that all manufacturers will produce machines for all four designs. The selection of any
specific design in accordance with this standard will be a matter of agreement between the manufacturer and the
purchaser.
NOTE 2 Designs other than the four specified may be necessary for particular applications.
NOTE 3 The values of torque and apparent power given in this standard are limiting values (that is, minimum or
maximum without tolerance), but it should be noted that values given in manufacturers' catalogues may include
tolerances in accordance with IEC 60034-1.
NOTE 4 The values tabled for locked rotor apparent power are based on r.m.s. symmetrical steady state locked
rotor currents; at motor switch on there will be a one-half cycle asymmetrical instantaneous peak current which
may range from 1,8 to 2,8 times the steady state value. The current peak and decay time are a function of the
motor design and switching angle.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.