oSIST prEN 13852-1:2009

Cranes - Offshore cranes - Part 1: General-purpose offshore cranes

This European Standard specifies the requirements for general-purpose offshore cranes including their supporting pedestals or structures and lifting of personnel.
The standard applies to cranes manufactured after the date of issue.
This European Standard does not cover the hazards involved with or the use of the following:
a)   fabrication, transportation, assembly, dismantling, disabling, scrapping or changing the configuration of the crane;
b)   lifting accessories, i.e. any item between the hook and the load;
c)   design temperature below – 40°C;
d)   operations at an ambient temperature above 40°C;
e)   lifting operations involving more than one crane;
f)   accidental loads due to collisions;
g)   hand powered cranes and other cranes with a rated capacity less than 2 t or outreach less than 8 meters
h)   rescue operations;
i)   subsea lifting operations.
The significant hazards covered by this European standard are identified in Clause 4.
Where National Authorities permit the use of general-purpose offshore crane for the lifting of personnel, the crane would at least need to fulfil the requirements of this standard.

Krane - Offshore-Krane - Teil 1: Offshore-Krane für allegemeine Verwendung

Diese Europäische Norm legt die Anforderungen an Offshore-Krane für allgemeine Verwendung einschließlich
ihrer Tragsäulen und Fundamente fest.
Diese Norm ist auf Krane anzuwenden, die nach dem Datum der Herausgabe dieser Norm hergestellt
werden.
Diese Europäische Norm gilt nicht für Gefahren in Verbindung mit Folgendem:
a) Herstellung, Transport, Montage, Demontage, Unbrauchbarmachung, Verschrottung oder Rüstzustandsänderung
des Krans;
b) Lastaufnahmemittel, d. h. alle Teile zwischen dem Haken und der Last;
c) Entwurfstemperaturen unter −40 °C;
d) Arbeiten bei Umgebungstemperaturen über 40 °C;
e) Hebearbeiten mit mehr als einem Kran;
f) unbeabsichtigte Beanspruchungen aufgrund von Zusammenstößen;
g) handgetriebene Krane und sonstige Krane mit einer Tragfähigkeit von weniger als 2 t oder einer
Ausladung von weniger als 8 m;
h) Rettungsmaßnahmen;
i) Unterwasser-Hebearbeiten.
Die durch diese Europäische Norm erfassten wesentlichen Gefahren sind in Abschnitt 4 aufgeführt.
Wenn nationale Behörden den Einsatz eines Offshore-Kranes für allgemeine Verwendung für den Transport
von Personal erlauben, muss der Kran mindestens die Anforderungen dieser Norm erfüllen.

Appareils de levage - Appareils de levage offshore - Partie 1: Appareils de levage offshore pour usage général

Le présent document s'applique aux grues off-shore d'usage général, y compris à leurs socles et aux structures d'appui.
Le présent document s'applique aux grues off-shore d'usage général à structure en acier.
Le présent document spécifie les prescriptions relatives à l'ensemble des phénomènes dangereux, situations dangereuses et événements dangereux majeurs relatifs aux grues off-shore d'usage général, pour le transport de marchandises et le levage de personnes, lorsque celles-ci sont utilisées comme prévu et dans les conditions prévues par l'évaluation du risque (voir Article 4).
Le présent document s'applique aux grues off-shore d'usage général fabriquées après la date d'approbation du présent document par le CEN.
Le présent document ne s'applique pas :
a)   au transport, au montage, au démontage, à la mise au rebut ou à l'installation de la grue ;
b)   à tout élément fixé au crochet, tel que les charges, les accessoires de levage de charge amovibles, les accessoires de levage, les nacelles, les supports et les conteneurs ;
c)   aux opérations de levage à des températures ambiantes inférieures à - 20 °C ;
d)   aux opérations de levage à des températures ambiantes supérieures à 45 °C ;
e)   aux charges accidentelles résultant de collisions, de tremblements de terre, d'explosions, etc., qui ne sont pas couvertes par les charges exceptionnelles définies dans le Tableau B.7 ;
f)   aux grues flottantes (couvertes par l'EN 13852-2), aux grues off-shore légères (couvertes par FprEN 13852-3) et aux grues à compensation de mouvement 2D/3D ;
g)   aux opérations de levage sous-marines ;
h)   aux opérations de levage impliquant plus d'un appareil de levage à charge suspendue ;
i)   aux opérations de sauvetage (hors entraînement).

Dvigala (žerjavi) - Dvigala na plavajočih objektih - 1. del: Dvigala na plavajočih objektih za splošne namene

General Information

• Status: Not Published
• Public Enquiry End Date: 24-Nov-2009
• ICS: 47.020.40 - Lifting and cargo handling equipment
• ICS: 53.020.20 - Cranes
• Technical Committee: DTN - Lift and transport appliances
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 19-Aug-2010
• Due Date: 24-Aug-2010
• Completion Date: 19-Aug-2010
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: FprEN 13852-1 - Cranes - Offshore cranes - Part 1: General-purpose offshore cranes

Relations

• Revised: SIST EN 13852-1:2004 - Cranes - Offshore cranes - Part 1: General - purpose offshore cranes
• Effective Date: 22-Dec-2008
• Revised: SIST EN 13852-1:2004 - Cranes - Offshore cranes - Part 1: General - purpose offshore cranes
• Effective Date: 18-Jan-2023
• Revised: SIST EN 13852-1:2004 - Cranes - Offshore cranes - Part 1: General - purpose offshore cranes
• Effective Date: 19-Jan-2023
• Revised: SIST EN 13852-1:2004 - Cranes - Offshore cranes - Part 1: General - purpose offshore cranes
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 13852-1:2009
01-november-2009
'YLJDODåHUMDYL'YLJDODQDSODYDMRþLKREMHNWLKGHO'YLJDODQDSODYDMRþLK
REMHNWLK]DVSORãQHQDPHQH
Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
Krane - Offshore-Krane - Teil 1: Offshore-Krane für allegemeine Verwendung
Appareils de levage - Appareils de levage offshore - Partie 1: Appareils de levage
offshore pour usage général
Ta slovenski standard je istoveten z: prEN 13852-1
ICS:
47.020.40 Dvigalna oprema in oprema Lifting and cargo handling
za pretovor equipment
53.020.20 Dvigala Cranes
oSIST prEN 13852-1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13852-1:2009

---------------------- Page: 2 ----------------------
oSIST prEN 13852-1:2009
EUROPEAN STANDARD
DRAFT
prEN 13852-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2009
ICS Will supersede EN 13852-1:2004
English Version
Cranes - Offshore cranes - Part 1: General-purpose offshore
cranes
Appareils de levage - Appareils de levage offshore - Partie Krane - Offshore-Krane - Teil 1: Offshore-Krane für
1: Appareils de levage offshore pour usage général allegemeine Verwendung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 147.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13852-1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13852-1:2009
prEN 13852-1:2009 (E)
Contents Page
Foreword .6
Introduction .7
1 Scope .8
2 Normative references .8
3 Terms and definitions . 12
4 List of significant hazards . 16
5 Safety requirements and/or protective measures . 17
5.1 General . 17
5.2 Strength and stability . 17
5.2.1 Selection of classification parameters . 17
5.2.2 In-service loads . 18
5.2.3 Out of service loads . 19
5.2.4 Failure mode analysis . 19
5.2.5 Seismic loads . 19
5.2.6 Load combinations . 20
5.2.7 Load chart . 20
5.2.8 Materials . 20
5.3 Equipment and components . 20
5.3.1 Electrotechnical equipment . 20
5.3.2 Non-electrotechnical equipment . 20
5.3.3 Power requirements . 20
5.3.4 Slewing drives . 21
5.3.5 Slewing bearings . 21
5.3.6 Slewing bearing fasteners . 21
5.3.7 Winches and brakes . 21
5.3.8 Wire rope termination . 22
5.3.9 Wire rope fastening to the drum . 22
5.3.10 Wire ropes . 22
5.3.11 Blocks and hooks . 23
5.3.12 Hydraulic cylinders . 23
5.3.13 Constant tension systems/motion compensators/shock absorbers . 23
5.4 Drive systems . 24
5.4.1 Electromagnetic compatibility . 24
5.4.2 Pneumatic systems . 24
5.4.3 Hydraulic systems . 24
5.4.4 Electrical systems. 24
5.5 Control station . 24
5.5.1 General . 24
5.5.2 Control cabin . 24
5.5.3 Windows . 25
5.5.4 Crane operator’s seat . 25
5.5.5 Cabin interior . 25
5.5.6 Cabin instrumentation . 25
5.5.7 Communications . 26
5.5.8 Machinery house and other enclosed spaces . 26
5.6 Noise reduction . 26
5.6.1 Noise reduction at source by design . 26
5.6.2 Noise reduction by information . 26
5.7 Access, guards etc. . 26
2

---------------------- Page: 4 ----------------------
oSIST prEN 13852-1:2009
prEN 13852-1:2009 (E)
5.7.1 Access . 26
5.7.2 Guards . 26
5.7.3 Hazardous substances . 26
5.7.4 Dropped objects . 26
5.7.5 Lifting arrangements for maintenance . 27
5.8 Controls, indicators and limiting devices . 27
5.8.1 General . 27
5.8.2 Controls . 27
5.8.3 Indicators. 28
5.8.4 Limiting devices . 29
5.9 Protection system . 30
5.9.1 Overload and over-moment protection . 30
5.9.2 Emergency operation system . 33
5.9.3 Emergency stop . 34
5.9.4 Fire protection . 34
5.9.5 Protective earthing . 34
5.10 Lifting of personnel . 34
5.10.1 General . 34
5.10.2 Rated capacity . 34
5.10.3 Secondary brake . 34
5.10.4 Cylinders . 35
5.10.5 Mode selection for personnel lifting . 35
6 Verification of the safety requirements and/or protective measures . 35
6.1 General . 35
6.2 Testing . 38
6.2.1 General . 38
6.2.2 Function test . 39
6.2.3 Installation test . 39
6.2.4 Test acceptance criteria. 39
6.2.5 Test load . 40
7 Information for use . 40
7.1 Documentation . 40
7.2 Operation . 41
7.2.1 General . 41
7.2.2 Checks before starting operation . 41
7.2.3 Checks during operation . 42
7.2.4 Crane out of service . 42
7.2.5 Lifting of personnel (if part of the intended use) . 42
7.3 Maintenance . 43
7.3.1 Inspections . 43
7.4 Marking . 44
7.4.1 Manufacturer’s plate . 44
7.4.2 Rated capacity information . 44
7.4.3 Components . 44
Annex A (normative) Selection of a suitable set of crane standards for a given application . 45
Annex B (normative) Determination of factors. 46
B.1 Calculation of the dynamic coefficient ΦΦ by the simplified method . 46
ΦΦ
n
B.2 Calculation of dynamic coefficient ΦΦΦΦ by motion response analysis . 47
n
B.3 Out of plane influences . 48
B.3.1 General . 48
B.3.2 Offlead load . 48
B.3.3 Sidelead load . 49
B.3.4 Horizontal load combination of the out-of-plane influences . 50
B.4 Hook velocity . 50
B.4.1 Hoisting and lowering velocity . 50
B.4.2 Horizontal hook velocity . 50
B.5 Load combinations . 51
3

---------------------- Page: 5 ----------------------
oSIST prEN 13852-1:2009
prEN 13852-1:2009 (E)
Annex C (normative) Environmental influences . 54
C.1 General . 54
C.2 Wind . 54
C.2.1 Mean wind velocities . 54
C.2.2 Boom stalling . 54
C.3 Floating units . 55
C.4 Thermal effects . 55
C.5 Ice . 56
C.6 Stowage . 56
C.7 Corrosion protection . 56
Annex D (normative) Failure mode analysis . 57
D.1 General . 57
D.2 Failure mode charts . 57
Annex E (normative) Material selection. 59
E.1 General . 59
E.2 Verification of material quality . 59
E.3 Forged rings for slewing bearings . 59
E.4 Slewing bearing fasteners . 60
E.5 Welded structures. 61
E.6 Non-welded components . 62
Annex F (informative) Control station instrumentation . 64
Annex G (normative) Wire rope safety factors . 65
G.1 General . 65
G.2 Static safety factors . 65
G.2.1 Running rigging . 65
G.2.2 Standing rigging . 65
G.3 Dynamic safety factors . 65
G.3.1 Running rigging . 65
G.3.2 Standing rigging . 66
G.4 Lifting of personnel . 66
Annex H (normative) Slewing bearings . 67
Annex I (normative) Requirements for brakes . 68
Annex J (normative) Ranking of safety systems . 69
Annex K (normative) Required performance levels (PLr) for SRP/CS according to EN ISO 13849-
1:2008 . 70
Annex L (informative) Typical general-purpose offshore cranes and terminology . 72
Annex M (normative) Design excursion envelopes . 77
Annex N (normative) Noise test code . 78
N.1 Introduction . 78
N.2 Sound power level determination . 78
N.2.1 Basic standard to be used . 78
N.2.2 Measurement and calculation procedure . 78
N.3 Emission sound pressure level determination . 79
N.3.1 Basic standard to be used . 79
N.3.2 Crane operator and microphone positions . 79
N.3.3 Specifications concerning the crane operating cabin . 79
N.3.4 Specification relating to wind speed . 79
N.3.5 Measurement and calculation procedure . 79
N.4 Operating conditions . 80
N.4.1 General . 80
N.4.2 Test procedure . 80
N.5 Information on measurement uncertainties . 82
N.6 Information to be recorded . 82
N.7 Information to be reported . 82
4

---------------------- Page: 6 ----------------------
oSIST prEN 13852-1:2009
prEN 13852-1:2009 (E)
N.8 Declaration and verification of noise emission values . 82
N.9 Noise measurement — test report . 83
Annex O (normative) Equipment for use in a hazardous area . 87
O.1 General . 87
O.2 Avoidance or reduction of ignition sources . 87
O.3 Electro technical equipment. 87
O.4 Non-electro technical equipment . 87
O.5 Electrostatic discharge . 87
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/EC . 89

5

---------------------- Page: 7 ----------------------
oSIST prEN 13852-1:2009
prEN 13852-1:2009 (E)
Foreword
This document (prEN 13852-1:2009) has been prepared by Technical Committee CEN/TC 147 “Cranes -
Safety”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13852-1:2004.
6

---------------------- Page: 8 ----------------------
oSIST prEN 13852-1:2009
prEN 13852-1:2009 (E)
Introduction
This European Standard has been prepared to be a harmonised standard to provide one means for
general-purpose offshore cranes to conform to the essential health and safety requirements of the Machinery
Directive, as mentioned in Annex ZA.
Absolute safety of cranes cannot be ensured by design alone, as their operation depends on the skill of
operators, maintenance personnel and inspectors as well as on the numerous technical parameters relating to
the crane and
...