SIST EN 300 720 V2.1.1:2017

Ultra-High Frequency (UHF) on-board vessels communications systems and equipment - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

The present document specifies the minimum technical characteristics required for UHF on board vessels radio
equipment and systems operating on frequencies allocated to the maritime mobile services by the ITU Radio
Regulations [i.1].
The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it
both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" [i.3].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Directive 2014/53/EU [i.3] may apply to equipment within the scope of the present
document.

Ultra visokofrekvenčni (UHF) komunikacijski sistemi in oprema za uporabo na krovu plovil - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU

Ta dokument določa minimalne tehnične lastnosti za ultra visokofrekvenčno (UHF) radijsko opremo in sisteme za uporabo na krovu plovil, ki delujejo prek frekvenc, ki so na podlagi ITU pravilnika o radiokomunikacijah [i.1] dodeljene pomorskim mobilnim storitvam.
Ta dokument vključuje zahteve, s katerimi se dokazuje, da »... mora biti radijska oprema sestavljena tako, da učinkovito uporablja in tudi podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivih motenj« [i.3].
Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 Direktive 2014/53/EU [i.3].

General Information

• Status: Published
• Public Enquiry End Date: 23-Jan-2017
• Publication Date: 12-Apr-2017
• ICS: 33.060.01 - Radiocommunications in general
• ICS: 47.020.70 - Navigation and control equipment
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 06-Feb-2017
• Due Date: 13-Apr-2017
• Completion Date: 13-Apr-2017
• Directive: 1999/5/EC - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Ref Project: ETSI EN 300 720 V2.2.0 (2016-10) - Ultra-High Frequency (UHF) on-board vessels communications systems and equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

Standards Content (Sample)

ETSI EN 300 720 V2.1.1 (2017-01)

HARMONISED EUROPEAN STANDARD
Ultra-High Frequency (UHF) on-board vessels
communications systems and equipment;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

2 ETSI EN 300 720 V2.1.1 (2017-01)

Reference
REN/ERM-TG26-136
Keywords
harmonised standard, maritime, radio, UHF

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 300 720 V2.1.1 (2017-01)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 General requirements . 10
4.1 Construction . 10
4.2 Frequencies. 10
4.3 Controls . 11
4.4 Switching time . 11
4.5 Safety precautions . 12
4.6 Class of emission and modulation characteristics . 12
4.7 Batteries for portable equipment . 12
4.8 Loudspeaker and microphone . 12
4.9 Labelling. 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal end extreme test conditions . 12
5.2 Test power source . 12
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal test voltage . 13
5.3.2.1 Battery power source. 13
5.3.2.2 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.1.1 Upper extreme temperature . 13
5.4.1.2 Lower extreme temperature . 13
5.4.2 Extreme test power supply values . 13
5.4.2.1 Upper extreme test voltage - Portable equipment . 13
5.4.2.2 Lower extreme test voltage - Portable equipment . 13
5.4.2.3 Extreme test voltages - Other equipment . 14
5.5 Procedure for tests at extreme temperatures . 14
6 General conditions of measurement . 14
6.1 Test connections . 14
6.2 Arrangements for test signals . 15
6.2.1 Test signals applied to the transmitter input . 15
6.2.1.1 Analogue . 15
6.2.1.2 Digital . 15
6.2.2 Test signals applied to the antenna terminal . 15
6.3 Receiver mute or squelch facility . 15
6.4 Normal test modulation . 15
6.4.1 Analogue . 15
6.4.2 Digital . 15
6.5 Artificial antenna . 16
6.6 Test channels . 16
6.7 Reference Bandwidths for emission measurements . 16
ETSI
4 ETSI EN 300 720 V2.1.1 (2017-01)
7 Environmental tests . 17
7.1 Procedure . 17
7.2 Performance check . 17
7.3 Drop test on to a hard surface - Portable equipment . 17
7.3.1 Definition . 17
7.3.2 Method of measurement . 17
7.3.3 Requirement . 18
7.4 Temperature tests . 18
7.4.1 General . 18
7.4.2 Dry heat . 18
7.4.2.1 Method of measurement . 18
7.4.2.2 Requirement . 18
7.4.3 Damp heat . 18
7.4.3.1 Method of measurement . 18
7.4.3.2 Requirement . 19
8 Transmitter . 19
8.1 Frequency error . 19
8.1.1 Definition . 19
8.1.2 Method of measurement . 19
8.1.3 Limits . 19
8.2 Maximum effective radiated power . 19
8.2.1 Definition . 19
8.2.2 Method of measurement . 19
8.2.3 Limit . 20
8.3 Frequency deviation - Analogue . 20
8.3.1 Definition . 20
8.3.2 Maximum frequency deviation . 20
8.3.2.1 Method of measurement . 20
8.3.2.2 Limit . 21
8.3.3 Frequency deviation at modulation frequencies above 3 kHz . 21
8.3.3.1 Method of measurement . 21
8.3.3.2 Limits . 21
8.4 Limitation characteristics of the modulator - Analogue . 22
8.4.1 Definition . 22
8.4.2 Method of measurement . 22
8.4.3 Limit . 22
8.5 Sensitivity of the modulator, including microphone (except for repeater equipment) - Analogue. 23
8.5.1 Definition . 23
8.5.2 Method of measurement . 23
8.5.3 Limit . 23
8.6 Audio frequency response - Analogue . 23
8.6.1 Definition . 23
8.6.2 Method of measurement . 23
8.6.3 Limit . 24
8.7 Audio frequency harmonic distortion of the emission - Analogue . 24
8.7.1 Definition . 24
8.7.2 Method of measurement . 24
8.7.3 Limit . 25
8.8 Adjacent channel power . 25
8.8.1 Analogue . 25
8.8.1.1 Definition . 25
8.8.1.2 Method of measurement . 25
8.8.1.3 Limit . 25
8.8.2 Digital . 26
8.8.2.1 Definition . 26
8.8.2.2 Methods of measurement . 26
8.8.2.3 Limit . 27
8.9 Residual modulation of the transmitter - Analogue . 27
8.9.1 Definition . 27
8.9.2 Method of measurement . 27
8.9.3 Limit . 27
ETSI
5 ETSI EN 300 720 V2.1.1 (2017-01)
8.10 Transient frequency behaviour of the transmitter . 28
8.10.1 Analogue . 28
8.10.1.1 Definition . 28
8.10.1.2 Method of measurement . 28
8.10.1.3 Limits . 30
8.10.2 Digital . 31
8.10.2.1 Definition . 31
8.10.2.2 Method of measurement . 31
8.10.2.3 Limits . 32
8.11 Conducted spurious emissions conveyed to the antenna . 32
8.11.1 Definition . 32
8.11.2 Method of measurement . 32
8.11.3 Limit . 32
8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 33
8.12.1 Definitions . 33
8.12.2 Method of measurement . 33
8.12.3 Limits . 34
9 Receiver . 34
9.1 Harmonic distortion and rated audio frequency output power - Analogue. 34
9.1.1 Definition . 34
9.1.2 Methods of measurement . 34
9.1.3 Limits . 35
9.2 Audio frequency response - Analogue . 35
9.2.1 Definition . 35
9.2.2 Method of measurement . 35
9.2.3 Limits . 35
9.3 Maximum usable sensitivity . 36
9.3.1 Analogue . 36
9.3.1.1 Definiton . 36
9.3.1.2 Method of measurement . 37
9.3.1.3 Limits . 37
9.3.2 Digital . 37
9.3.2.1 Definiton . 37
9.3.2.2 Methods of measurement . 37
9.3.2.2.1 Method of measurement with continuous bit streams . 37
9.3.2.2.2 Method of measurement with messages . 38
9.3.2.3 Limits . 38
9.4 Co-channel rejection - Analogue . 38
9.4.1 Definition . 38
9.4.2 Method of measurement . 38
9.4.3 Limit . 39
9.5 Adjacent channel selectivity . 39
9.5.1 Analogue . 39
9.5.1.1 Definition . 39
9.5.1.2 Method of measurement . 39
9.5.1.3 Limits . 39
9.5.2 Digital . 39
9.5.2.1 Definition . 39
9.5.2.2 Method of measurement . 40
9.5.2.2.1 Continuous bit stream method . 40
9.5.2.2.2 Discontinuous (messages) method . 40
9.5.2.3 Limits . 41
9.6 Spurious response rejection . 41
9.6.1 Analogue . 41
9.6.1.1 Definition . 41
9.6.1.2 Method of measurement . 41
9.6.1.3 Limit . 42
9.6.2 Digital . 42
9.6.2.1 Definition . 42
9.6.2.2 Method of measurement . 42
9.6.2.2.1 Introduction to the method of measurement . 42
ETSI
6 ETSI EN 300 720 V2.1.1 (2017-01)
9.6.2.2.2 Method of search over the "limited frequency range" . 43
9.6.2.2.3 Method of measurement (continuous bit streams) . 44
9.6.2.2.4 Method of measurement (with messages) . 44
9.6.2.3 Limits . 45
9.7 Intermodulation response . 45
9.7.1 Analogue . 45
9.7.1.1 Definition . 45
9.7.1.2 Method of measurement . 46
9.7.1.3 Limit . 46
9.7.2 Digital . 46
9.7.2.1 Definition . 46
9.7.2.2 Method of measurement . 46
9.7.2.2.1 Method of measurement (continuous bit stream) . 46
9.7.2.2.2 Method of measurement with messages . 47
9.7.2.3 Limit . 48
9.8 Blocking or desensitization . 48
9.8.1 Analogue . 48
9.8.1.1 Definition . 48
9.8.1.2 Method of measurement . 48
9.8.1.3 Limit . 49
9.8.2 Digital . 49
9.8.2.1 Definition . 49
9.8.2.2 Method of measurement . 49
9.8.2.2.1 Continuous bit streams . 49
9.8.2.2.2 Method of measurement with messages . 50
9.8.2.3 Limit . 51
9.9 Conducted spurious emissions conveyed to the antenna . 51
9.9.1 Definition . 51
9.9.2 Method of measurement . 51
9.9.3 Limit . 51
9.10 Radiated spurious emissions. 51
9.10.1 Definition . 51
9.10.2 Method of measurements . 51
9.10.3 Limit . 52
10 Testing for compliance with technical requirements . 52
10.1 Environmental conditions for testing . 52
10.2 Interpretation of the measurement results . 52
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 54
Annex B (normative): Measuring receiver for adjacent channel power measurement -
Analogue . 56
B.1 Power measuring receiver specification . 56
B.1.0 General . 56
B.1.1 IF filter . 56
B.1.2 Attenuation indicator . 57
B.1.3 rms value indicator . 57
B.1.4 Oscillator and amplifier . 57
History . 58

ETSI
7 ETSI EN 300 720 V2.1.1 (2017-01)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
National transposition dates
Date of adoption of this EN: 24 January 2017
Date of latest announcement of this EN (doa): 30 April 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2017
Date of withdrawal of any conflicting National Standard (dow): 31 October 2018

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
8 ETSI EN 300 720 V2.1.1 (2017-01)
1 Scope
The present document specifies the minimum technical characteristics required for UHF on board vessels radio
equipment and systems operating on frequencies allocated to the maritime mobile services by the ITU Radio
Regulations [i.1].
The present document contains requirements to demonstrate that ". Radio equipment shall be so constructed that it
both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" [i.3].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Directive 2014/53/EU [i.3] may apply to equipment within the scope of the present
document.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R M.1174-3 (2015): "Technical characteristics of equipment used for
on-board vessel communications in the bands between 450 and 470 MHz".
[2] Recommendation ITU-T O.41 (1994): "Psophometer for use on telephone-type circuits".
[3] ISO 25862:2009: "Ships and marine technology -- Marine magnetic compasses, binnacles and
azimuth reading devices".
[4] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
[5] Recommendation ITU-T O.153 (1992): "Basic parameters for the measurement of error
performance at bit rates below the primary rate".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ITU Radio Regulations (2016).
[i.2] Recommendation ITU-R SM.332-4: "Selectivity of receivers".
ETSI
9 ETSI EN 300 720 V2.1.1 (2017-01)
[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.4] ETSI TR 100 028-1 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics;
Part 1".
[i.5] ETSI TR 100 028-2 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics;
Part 2".
[i.6] ETSI TS 102 658: "Digital Private Mobile Radio (dPMR) using FDMA with a channel spacing of
6,25 kHz".
[i.7] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standa
...

Draft ETSI EN 300 720 V2.2.0 (2016-10)

HARMONISED EUROPEAN STANDARD
Ultra-High Frequency (UHF) on-board vessels
communications systems and equipment;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

2 Draft ETSI EN 300 720 V2.2.0 (2016-10)

Reference
REN/ERM-TG26-136
Keywords
Harmonised standard, maritime, radio, UHF

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Draft ETSI EN 300 720 V2.2.0 (2016-10)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 General requirements . 10
4.1 Construction . 10
4.2 Frequencies. 10
4.3 Controls . 11
4.4 Switching time . 12
4.5 Safety precautions . 12
4.6 Class of emission and modulation characteristics . 12
4.7 Batteries for portable equipment . 12
4.8 Loudspeaker and microphone . 12
4.9 Labelling. 12
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal end extreme test conditions . 12
5.2 Test power source . 13
5.3 Normal test conditions . 13
5.3.1 Normal temperature and humidity . 13
5.3.2 Normal test voltage . 13
5.3.2.1 Battery power source. 13
5.3.2.2 Other power sources . 13
5.4 Extreme test conditions . 13
5.4.1 Extreme temperatures . 13
5.4.1.1 Upper extreme temperature . 13
5.4.1.2 Lower extreme temperature . 13
5.4.2 Extreme test power supply values . 13
5.4.2.1 Upper extreme test voltage - Portable equipment . 13
5.4.2.2 Lower extreme test voltage - Portable equipment . 14
5.4.2.3 Extreme test voltages - Other equipment . 14
5.5 Procedure for tests at extreme temperatures . 14
6 General conditions of measurement . 14
6.1 Test connections . 14
6.2 Arrangements for test signals . 15
6.2.1 Test signals applied to the transmitter input . 15
6.2.1.1 Analogue . 15
6.2.1.2 Digital . 15
6.2.2 Test signals applied to the antenna terminal . 15
6.3 Receiver mute or squelch facility . 15
6.4 Normal test modulation . 15
6.4.1 Analogue . 15
6.4.2 Digital . 15
6.5 Artificial antenna . 16
6.6 Test channels . 16
6.7 Reference Bandwidths for emission measurements . 16
ETSI
4 Draft ETSI EN 300 720 V2.2.0 (2016-10)
7 Environmental tests . 17
7.1 Procedure . 17
7.2 Performance check . 17
7.3 Drop test on to a hard surface - Portable equipment . 17
7.3.1 Definition . 17
7.3.2 Method of measurement . 17
7.3.3 Requirement . 18
7.4 Temperature tests . 18
7.4.1 General . 18
7.4.2 Dry heat . 18
7.4.2.1 Method of measurement . 18
7.4.2.2 Requirement . 18
7.4.3 Damp heat . 18
7.4.3.1 Method of measurement . 18
7.4.3.2 Requirement . 19
8 Transmitter . 19
8.1 Frequency error . 19
8.1.1 Definition . 19
8.1.2 Method of measurement . 19
8.1.3 Limits . 19
8.2 Maximum effective radiated power . 19
8.2.1 Definition . 19
8.2.2 Method of measurement . 19
8.2.3 Limit . 20
8.3 Frequency deviation - Analogue . 20
8.3.1 Definition . 20
8.3.2 Maximum frequency deviation . 20
8.3.2.1 Method of measurement . 20
8.3.2.2 Limit . 21
8.3.3 Frequency deviation at modulation frequencies above 3 kHz . 21
8.3.3.1 Method of measurement . 21
8.3.3.2 Limits . 21
8.4 Limitation characteristics of the modulator - Analogue . 22
8.4.1 Definition . 22
8.4.2 Method of measurement . 22
8.4.3 Limit . 22
8.5 Sensitivity of the modulator, including microphone (except for repeater equipment) - Analogue. 23
8.5.1 Definition . 23
8.5.2 Method of measurement . 23
8.5.3 Limit . 23
8.6 Audio frequency response - Analogue . 23
8.6.1 Definition . 23
8.6.2 Method of measurement . 23
8.6.3 Limit . 24
8.7 Audio frequency harmonic distortion of the emission - Analogue . 24
8.7.1 Definition . 24
8.7.2 Method of measurement . 24
8.7.3 Limit . 25
8.8 Adjacent channel power . 25
8.8.1 Analogue . 25
8.8.1.1 Definition . 25
8.8.1.2 Method of measurement . 25
8.8.1.3 Limit . 25
8.8.2 Digital . 26
8.8.2.1 Definition . 26
8.8.2.2 Methods of measurement . 26
8.8.2.3 Limit . 27
8.9 Residual modulation of the transmitter - Analogue . 27
8.9.1 Definition . 27
8.9.2 Method of measurement . 27
8.9.3 Limit . 27
ETSI
5 Draft ETSI EN 300 720 V2.2.0 (2016-10)
8.10 Transient frequency behaviour of the transmitter . 28
8.10.1 Analogue . 28
8.10.1.1 Definition . 28
8.10.1.2 Method of measurement . 28
8.10.1.3 Limits . 30
8.10.2 Digital . 31
8.10.2.1 Definition . 31
8.10.2.2 Method of measurement . 31
Characteristics of the transient power measuring device . 32
8.10.2.3 Limits . 32
8.11 Conducted spurious emissions conveyed to the antenna . 32
8.11.1 Definition . 32
8.11.2 Method of measurement . 32
8.11.3 Limit . 33
8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 33
8.12.1 Definitions . 33
8.12.2 Method of measurement . 33
8.12.3 Limits . 34
9 Receiver . 34
9.1 Harmonic distortion and rated audio frequency output power - Analogue. 34
9.1.1 Definition . 34
9.1.2 Methods of measurement . 34
9.1.3 Limits . 35
9.2 Audio frequency response - Analogue . 35
9.2.1 Definition . 35
9.2.2 Method of measurement . 35
9.2.3 Limits . 35
9.3 Maximum usable sensitivity . 36
9.3.1 Analogue . 36
9.3.1.1 Definiton . 36
9.3.1.2 Method of measurement . 37
9.3.1.3 Limits . 37
9.3.2 Digital . 37
9.3.2.1 Definiton . 37
9.3.2.2 Methods of measurement . 37
9.3.2.2.1 Method of measurement with continuous bit streams . 37
9.3.2.2.2 Method of measurement with messages . 38
9.3.2.3 Limits . 38
9.4 Co-channel rejection - Analogue . 38
9.4.1 Definition . 38
9.4.2 Method of measurement . 38
9.4.3 Limit . 39
9.5 Adjacent channel selectivity . 39
9.5.1 Analogue . 39
9.5.1.1 Definition . 39
9.5.1.2 Method of measurement . 39
9.5.1.3 Limits . 39
9.5.2 Digital . 39
9.5.2.1 Definition . 39
9.5.2.2 Method of measurement . 40
9.5.2.2.1 Continuous bit stream method . 40
9.5.2.2.2 Discontinuous (messages) method . 40
9.5.2.3 Limits . 41
9.6 Spurious response rejection . 41
9.6.1 Analogue . 41
9.6.1.1 Definition . 41
9.6.1.2 Method of measurement . 41
9.6.1.3 Limit . 42
9.6.2 Digital . 42
9.6.2.1 Definition . 42
9.6.2.2 Method of measurement . 42
ETSI
6 Draft ETSI EN 300 720 V2.2.0 (2016-10)
9.6.2.2.1 Introduction to the method of measurement . 42
9.6.2.2.2 Method of search over the "limited frequency range" . 43
9.6.2.2.3 Method of measurement (continuous bit streams) . 44
9.6.2.2.4 Method of measurement (with messages) . 44
9.6.2.3 Limits . 45
9.7 Intermodulation response . 45
9.7.1 Analogue . 45
9.7.1.1 Definition . 45
9.7.1.2 Method of measurement . 46
9.7.1.3 Limit . 46
9.7.2 Digital . 46
9.7.2.1 Definition . 46
9.7.2.2 Method of measurement . 46
9.7.2.2.1 Method of measurement (continuous bit stream) . 46
9.7.2.2.2 Method of measurement with messages . 47
9.7.2.3 Limit . 48
9.8 Blocking or desensitization . 48
9.8.1 Analogue . 48
9.8.1.1 Definition . 48
9.8.1.2 Method of measurement . 48
9.8.1.3 Limit . 49
9.8.2 Digital . 49
9.8.2.1 Definition . 49
9.8.2.2 Method of measurement . 49
9.8.2.2.1 Continuous bit streams . 49
9.8.2.2.2 Method of measurement with messages . 50
9.8.2.3 Limit . 51
9.9 Conducted spurious emissions conveyed to the antenna . 51
9.9.1 Definition . 51
9.9.2 Method of measurement . 51
9.9.3 Limit . 51
9.10 Radiated spurious emissions. 51
9.10.1 Definition . 51
9.10.2 Method of measurements . 51
9.10.3 Limit . 52
10 Testing for compliance with technical requirements . 52
10.1 Environmental conditions for testing . 52
10.2 Interpretation of the measurement results . 52
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 54
Annex B (normative): Measuring receiver for adjacent channel power measurement -
Analogue . 56
B.1 Power measuring receiver specification . 56
B.1.0 General . 56
B.1.1 IF filter . 56
B.1.2 Attenuation indicator . 57
B.1.3 rms value indicator . 57
B.1.4 Oscillator and amplifier . 57
History . 58

ETSI
7 Draft ETSI EN 300 720 V2.2.0 (2016-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
8 Draft ETSI EN 300 720 V2.2.0 (2016-10)
1 Scope
The present document specifies the minimum technical characteristics required for UHF on board vessels radio
equipment and systems operating on frequencies allocated to the maritime mobile services by the ITU Radio
Regulations [i.1].
The present document contains requirements to demonstrate that ". Radio equipment shall be so constructed that it
both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" [i.3].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Directive 2014/53/EU [i.3] may apply to equipment within the scope of the present
document.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R M.1174-3 (2015): "Technical characteristics of equipment used for
on-board vessel communications in the bands between 450 and 470 MHz".
[2] Recommendation ITU-T O.41 (1994): "Psophometer for use on telephone-type circuits".
[3] ISO 25862:2009: "Ships and marine technology -- Marine magnetic compasses, binnacles and
azimuth reading devices".
[4] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
[5] Recommendation ITU-T O.153 (1992): "Basic parameters for the measurement of error
performance at bit rates below the primary rate".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ITU Radio Regulations (2016).
[i.2] Recommendation ITU-R SM.332-4: "Selectivity of receivers".
ETSI
9 Draft ETSI EN 300 720 V2.2.0 (2016-10)
[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.4] ETSI TR 100 028-1 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics;
Part 1".
[i.5] ETSI TR 100 028-2 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipme
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ultra-High Frequency (UHF) on-board vessels communications systems and equipment - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU47.020.70Navigacijska in krmilna opremaNavigation and control equipment33.060.01Radijske komunikacije na splošnoRadiocommunications in generalICS:Ta slovenski standard je istoveten z:ETSI EN 300 720 V2.1.1 (2017-01)SIST EN 300 720 V2.1.1:2017en01-maj-2017SIST EN 300 720 V2.1.1:2017SLOVENSKI
STANDARD
ETSI EN 300 720 V2.1.1 (2017-01) Ultra-High Frequency (UHF) on-board vessels communications systems and equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 300 720 V2.1.1:2017

ETSI ETSI EN 300 720 V2.1.1 (2017-01) 2
Reference REN/ERM-TG26-136 Keywords harmonised standard, maritime, radio, UHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: [phone]
Fax: [phone]
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 720 V2.1.1:2017

ETSI ETSI EN 300 720 V2.1.1 (2017-01) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 10 3.3 Abbreviations . 10 4 General requirements . 10 4.1 Construction . 10 4.2 Frequencies. 10 4.3 Controls . 11 4.4 Switching time . 11 4.5 Safety precautions . 12 4.6 Class of emission and modulation characteristics . 12 4.7 Batteries for portable equipment . 12 4.8 Loudspeaker and microphone . 12 4.9 Labelling. 12 5 Test conditions, power sources and ambient temperatures . 12 5.1 Normal end extreme test conditions . 12 5.2 Test power source . 12 5.3 Normal test conditions . 13 5.3.1 Normal temperature and humidity . 13 5.3.2 Normal test voltage . 13 5.3.2.1 Battery power source. 13 5.3.2.2 Other power sources . 13 5.4 Extreme test conditions . 13 5.4.1 Extreme temperatures . 13 5.4.1.1 Upper extreme temperature . 13 5.4.1.2 Lower extreme temperature . 13 5.4.2 Extreme test power supply values . 13 5.4.2.1 Upper extreme test voltage - Portable equipment . 13 5.4.2.2 Lower extreme test voltage - Portable equipment . 13 5.4.2.3 Extreme test voltages - Other equipment . 14 5.5 Procedure for tests at extreme temperatures . 14 6 General conditions of measurement . 14 6.1 Test connections . 14 6.2 Arrangements for test signals . 15 6.2.1 Test signals applied to the transmitter input . 15 6.2.1.1 Analogue . 15 6.2.1.2 Digital . 15 6.2.2 Test signals applied to the antenna terminal . 15 6.3 Receiver mute or squelch facility . 15 6.4 Normal test modulation . 15 6.4.1 Analogue . 15 6.4.2 Digital . 15 6.5 Artificial antenna . 16 6.6 Test channels . 16 6.7 Reference Bandwidths for emission measurements . 16 SIST EN 300 720 V2.1.1:2017

ETSI ETSI EN 300 720 V2.1.1 (2017-01) 4 7 Environmental tests . 17 7.1 Procedure . 17 7.2 Performance check . 17 7.3 Drop test on to a hard surface - Portable equipment . 17 7.3.1 Definition . 17 7.3.2 Method of measurement . 17 7.3.3 Requirement . 18 7.4 Temperature tests . 18 7.4.1 General . 18 7.4.2 Dry heat . 18 7.4.2.1 Method of measurement . 18 7.4.2.2 Requirement . 18 7.4.3 Damp heat . 18 7.4.3.1 Method of measurement . 18 7.4.3.2 Requirement . 19 8 Transmitter . 19 8.1 Frequency error . 19 8.1.1 Definition . 19 8.1.2 Method of measurement . 19 8.1.3 Limits . 19 8.2 Maximum effective radiated power . 19 8.2.1 Definition . 19 8.2.2 Method of measurement . 19 8.2.3 Limit . 20 8.3 Frequency deviation - Analogue . 20 8.3.1 Definition . 20 8.3.2 Maximum frequency deviation . 20 8.3.2.1 Method of measurement . 20 8.3.2.2 Limit . 21 8.3.3 Frequency deviation at modulation frequencies above 3 kHz . 21 8.3.3.1 Method of measurement . 21 8.3.3.2 Limits . 21 8.4 Limitation characteristics of the modulator - Analogue . 22 8.4.1 Definition . 22 8.4.2 Method of measurement . 22 8.4.3 Limit . 22 8.5 Sensitivity of the modulator, including microphone (except for repeater equipment) - Analogue. 23 8.5.1 Definition . 23 8.5.2 Method of measurement . 23 8.5.3 Limit . 23 8.6 Audio frequency response - Analogue . 23 8.6.1 Definition . 23 8.6.2 Method of measurement . 23 8.6.3 Limit . 24 8.7 Audio frequency harmonic distortion of the emission - Analogue . 24 8.7.1 Definition . 24 8.7.2 Method of measurement . 24 8.7.3 Limit . 25 8.8 Adjacent channel power . 25 8.8.1 Analogue . 25 8.8.1.1 Definition . 25 8.8.1.2 Method of measurement . 25 8.8.1.3 Limit . 25 8.8.2 Digital . 26 8.8.2.1 Definition . 26 8.8.2.2 Methods of measurement . 26 8.8.2.3 Limit . 27 8.9 Residual modulation of the transmitter - Analogue . 27 8.9.1 Definition . 27 8.9.2 Method of measurement . 27 8.9.3 Limit . 27 SIST EN 300 720 V2.1.1:2017

ETSI ETSI EN 300 720 V2.1.1 (2017-01) 5 8.10 Transient frequency behaviour of the transmitter . 28 8.10.1 Analogue . 28 8.10.1.1 Definition . 28 8.10.1.2 Method of measurement . 28 8.10.1.3 Limits . 30 8.10.2 Digital . 31 8.10.2.1 Definition . 31 8.10.2.2 Method of measurement . 31 8.10.2.3 Limits . 32 8.11 Conducted spurious emissions conveyed to the antenna . 32 8.11.1 Definition . 32 8.11.2 Method of measurement . 32 8.11.3 Limit . 32 8.12 Cabinet radiation and conducted spurious emissions other than those conveyed to the antenna . 33 8.12.1 Definitions . 33 8.12.2 Method of measurement . 33 8.12.3 Limits . 34 9 Receiver . 34 9.1 Harmonic distortion and rated audio frequency output power - Analogue. 34 9.1.1 Definition . 34 9.1.2 Methods of measurement . 34 9.1.3 Limits . 35 9.2 Audio frequency response - Analogue . 35 9.2.1 Definition . 35 9.2.2 Method of measurement . 35 9.2.3 Limits . 35 9.3 Maximum usable sensitivity . 36 9.3.1 Analogue . 36 9.3.1.1 Definiton . 36 9.3.1.2 Method of measurement . 37 9.3.1.3 Limits . 37 9.3.2 Digital . 37 9.3.2.1 Definiton . 37 9.3.2.2 Methods of measurement . 37 9.3.2.2.1 Method of measurement with continuous bit streams . 37 9.3.2.2.2 Method of measurement with messages . 38 9.3.2.3 Limits . 38 9.4 Co-channel rejection - Analogue . 38 9.4.1 Definition . 38 9.4.2 Method of measurement . 38 9.4.3 Limit . 39 9.5 Adjacent channel selectivity . 39 9.5.1 Analogue . 39 9.5.1.1 Definition . 39 9.5.1.2 Method of measurement . 39 9.5.1.3 Limits . 39 9.5.2 Digital . 39 9.5.2.1 Definition . 39 9.5.2.2 Method of measurement . 40 9.5.2.2.1 Continuous bit stream method . 40 9.5.2.2.2 Discontinuous (messages) method . 40 9.5.2.3 Limits . 41 9.6 Spurious response rejection . 41 9.6.1 Analogue . 41 9.6.1.1 Definition . 41 9.6.1.2 Method of measurement . 41 9.6.1.3 Limit . 42 9.6.2 Digital . 42 9.6.2.1 Definition . 42 9.6.2.2 Method of measurement . 42 9.6.2.2.1 Introduction to the method of measurement . 42 SIST EN 300 720 V2.1.1:2017

ETSI ETSI EN 300 720 V2.1.1 (2017-01) 6 9.6.2.2.2 Method of search over the "limited frequency range" . 43 9.6.2.2.3 Method of measurement (continuous bit streams) . 44 9.6.2.2.4 Method of measurement (with messages) . 44 9.6.2.3 Limits . 45 9.7 Intermodulation response . 45 9.7.1 Analogue . 45 9.7.1.1 Definition . 45 9.7.1.2 Method of measurement . 46 9.7.1.3 Limit . 46 9.7.2 Digital . 46 9.7.2.1 Definition . 46 9.7.2.2 Method of measurement . 46 9.7.2.2.1 Method of measurement (continuous bit stream) . 46 9.7.2.2.2 Method of measurement with messages . 47 9.7.2.3 Limit . 48 9.8 Blocking or desensitization . 48 9.8.1 Analogue . 48 9.8.1.1 Definition . 48 9.8.1.2 Method of measurement . 48 9.8.1.3 Limit . 49 9.8.2 Digital . 49 9.8.2.1 Definition . 49 9.8.2.2 Method of measurement . 49 9.8.2.2.1 Continuous bit streams . 49 9.8.2.2.2 Method of measurement with messages . 50 9.8.2.3 Limit . 51 9.9 Conducted spurious emissions conveyed to the antenna . 51 9.9.1 Definition . 51 9.9.2 Method of measurement . 51 9.9.3 Limit . 51 9.10 Radiated spurious emissions. 51 9.10.1 Definition . 51 9.10.2 Method of measurements . 51 9.10.3 Limit . 52 10 Testing for compliance with technical requirements . 52 10.1 Environmental conditions for testing . 52 10.2 Interpretation of the measurement results . 52 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 54 Annex B (normative): Measuring receiver for adjacent channel power measurement - Analogue . 56 B.1 Power measuring receiver specification . 56 B.1.0 General . 56 B.1.1 IF filter . 56 B.1.2 Attenuation indicator . 57 B.1.3 rms value indicator . 57 B.1.4 Oscillator and amplifier . 57 History . 58
ETSI ETSI EN 300 720 V2.1.1 (2017-01) 7 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.3]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations.
National transposition dates Date of adoption of this EN: 24 January 2017 Date of latest announcement of this EN (doa): 30 April 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 October 2017 Date of withdrawal of any conflicting National Standard (dow): 31 October 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. SIST EN 300 720 V2.1.1:2017

ETSI ETSI EN 300 720 V2.1.1 (2017-01) 8 1 Scope The present document specifies the minimum technical characteristics required for UHF on board vessels radio equipment and systems operating on frequencies allocated to the maritime mobile services by the ITU Radio Regulations [i.1]. The present document contains requirements to demonstrate that ". Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" [i.3]. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Directive 2014/53/EU [i.3] may apply to equipment within the scope of the present document. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] Recommendation ITU-R M.1174-3 (2015): "Technical characteristics of equipment used for on-board vessel communications in the bands between 450 and 470 MHz". [2] Recommendation ITU-T O.41 (1994): "Psophometer for use on telephone-type circuits". [3] ISO 25862:2009: "Ships and marine technology -- Marine magnetic compasses, binnacles and azimuth reading devices". [4] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz". [5] Recommendation ITU-T O.153 (1992): "Basic parameters for the measurement of error performance at bit rates below the primary rate". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] ITU Radio Regulations (2016). [i.2] Recommendation ITU-R SM.332-4: "Selectivity of receivers". SIST EN 300 720 V2.1.1:2017

ETSI ETSI EN 300 720 V2.1.1 (2017-01) 9 [i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.4] ETSI TR 100 028-1 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 1". [i.5] ETSI TR 100 028-2 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2". [i.6] ETSI TS 102 658: "Digital Private Mobile Radio (dPMR) using FDMA with a channel spacing of 6,25 kHz". [i.7] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnic
...