SIST EN 12020-1:2022
(Main)Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery
Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery
This document specifies technical conditions for inspection and delivery of alloys EN AW-6060 and EN AW 6063 extruded precision profiles manufactured with and without a thermal barrier (see Figures 1 and 2) and without further surface treatment.
Precision profiles covered in this document are distinguished from extruded profiles for general applications covered in EN 755 9 by the following characteristics:
- they are designed with mostly uniformly wall thicknesses;
- they are mainly used for mechanical engineering, architectural and automotive (except crash-elements) applications;
- the maximum weight by meter is 10 kg/m;
- the maximum wall thickness proportion (Smax/Smin) is 3,5.
In the case of profiles, which, due to the complexity of their design, are difficult to manufacture and specify, special agreements between supplier and purchaser may need to be reached.
NOTE The effect of the thermal barrier material on the dimensional tolerances is covered by EN 12020 2 although the actual thermal barrier material itself is not (see EN 14024).
Aluminium und Aluminiumlegierungen - Stranggepresste Präzisionsprofile aus Legierungen EN AW-6060 und EN AW-6063 - Teil 1: Technische Lieferbedingungen
Dieses Dokument legt die Technischen Lieferbedingungen für stranggepresste Präzisionsprofile aus den Legierungen EN AW 6060 und EN AW 6063 fest, die mit oder ohne Wärmedämmung (siehe Bild 1 und Bild 2) hergestellt werden und ohne weitere Oberflächenbehandlung geliefert werden.
Die in diesem Dokument beschriebenen Präzisionsprofile unterscheiden sich von den stranggepressten Profilen für allgemeine Anwendungen nach EN 755 9 wie folgt:
- sie werden mit meist gleichmäßigen Wanddicken ausgeführt;
- sie werden hauptsächlich im Maschinenbau, in der Architektur und im Automobilbau (außer Crashelementen) eingesetzt;
- das maximale Metergewicht beträgt 10 kg/m;
- das maximale Wanddickenverhältnis (Smax/Smin) beträgt 3,5.
Bei Profilen, die aufgrund ihrer komplexen Konstruktion schwierig herzustellen und zu spezifizieren sind, können besondere Vereinbarungen zwischen Lieferer und Käufer notwendig sein.
ANMERKUNG Der Einfluss des Materials für die Wärmedämmung auf die Grenzabmaße wird in EN 12020 2 berücksichtigt, wenngleich das eigentliche Material für die Wärmedämmung nicht enthalten ist (siehe EN 14024).
Aluminium et alliages d'aluminium - Profilés de précision filés en alliages EN AW-6060 et EN AW-6063 - Partie 1: Conditions techniques de contrôle et de livraison
Le présent document spécifie les conditions techniques de contrôle et de livraison des profilés de précision filés en alliages EN AW 6060 et EN AW 6063 fabriqués avec ou sans barrière thermique (voir Figures 1 et 2) et sans autre traitement de surface.
Les profilés de précision traités dans le présent document se distinguent des produits filés pour application générale traités dans l'EN 755 9 par les caractéristiques suivantes :
- ils sont conçus avec des épaisseurs de paroi le plus souvent uniformes ;
- ils sont principalement destinés à des applications du génie mécanique, de l’architecture et de l’automobile (à l’exception des éléments exposés aux collisions) ;
- la masse maximale par mètre est de 10 kg/m ;
- le rapport maximal d’épaisseur de paroi (Smax/Smin) est de 3,5.
Dans le cas de profilés qui, en raison de la complexité de leur conception, sont difficiles à spécifier et à fabriquer, il peut s’avérer nécessaire que le fournisseur et l’acheteur conviennent d’accords spéciaux.
NOTE Les effets du matériau de la barrière thermique sur les tolérances dimensionnelles sont traités dans l'EN 12020 2, même si le matériau lui-même de la barrière thermique proprement dite ne l'est pas (voir l'EN 14024).
Aluminij in aluminijeve zlitine - Precizni iztiskani profili v zlitinah EN AW-6060 in EN AW-6063 - 1. del: Tehnični pogoji za pregled in dobavo
Ta dokument določa tehnične pogoje za pregled in dobavo preciznih iztiskanih profilov v zlitinah EN AW-6060 in EN AW 6063, izdelanih s termično prevleko ali brez nje (glej sliki 1 in 2) in brez nadaljnje površinske obdelave.
Precizni profili, ki jih zajema ta dokument, se razlikujejo od iztiskanih profilov za splošno uporabo, ki so zajeti v standardu EN 755-9, po naslednjih lastnostih:
– zasnovani so z večinoma enakomernimi debelinami sten;
– uporabljajo se predvsem v strojništvu, arhitekturi in avtomobilski industriji (razen elementov proti trčenju);
– največja teža na meter je 10 kg/m;
– največji delež debeline stene (Smax/Smin) je 3,5.
Pri profilih, ki jih je zaradi kompleksnosti zasnove težko izdelati in določiti, je morda treba doseči posebne dogovore med dobaviteljem in kupcem.
OPOMBA: Učinek termične prevleke na tolerance mer je zajet v standardu EN 12020-2, čeprav sam material termične prevleke ni zajet (glej standard EN 14024).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12020-1:2022
01-maj-2022
Nadomešča:
SIST EN 12020-1:2008
Aluminij in aluminijeve zlitine - Precizni iztiskani profili v zlitinah EN AW-6060 in
EN AW-6063 - 1. del: Tehnični pogoji za pregled in dobavo
Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and
EN AW-6063 - Part 1: Technical conditions for inspection and delivery
Aluminium und Aluminiumlegierungen - Stranggepresste Präzisionsprofile aus
Legierungen EN AW-6060 und EN AW-6063 - Teil 1: Technische Lieferbedingungen
Aluminium et alliages d'aluminium - Profilés de précision filés en alliages EN AW-6060 et
EN AW-6063 - Partie 1: Conditions techniques de contrôle et de livraison
Ta slovenski standard je istoveten z: EN 12020-1:2022
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 12020-1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12020-1:2022
---------------------- Page: 2 ----------------------
SIST EN 12020-1:2022
EN 12020-1
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 77.150.10 Supersedes EN 12020-1:2008
English Version
Aluminium and aluminium alloys - Extruded precision
profiles in alloys EN AW-6060 and EN AW-6063 - Part 1:
Technical conditions for inspection and delivery
Aluminium et alliages d'aluminium - Profilés de Aluminium und Aluminiumlegierungen -
précision filés en alliages EN AW-6060 et EN AW-6063 Stranggepresste Präzisionsprofile aus Legierungen EN
- Partie 1: Conditions techniques de contrôle et de AW-6060 und EN AW-6063 - Teil 1: Technische
livraison Lieferbedingungen
This European Standard was approved by CEN on 31 January 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12020-1:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12020-1:2022
EN 12020-1:2022 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Ordering information . 5
4.1 General. 5
4.2 Reference to a drawing . 6
5 Requirements . 7
5.1 Production and manufacturing processes . 7
5.2 Quality control . 7
5.3 Chemical composition limit . 7
5.4 Mechanical properties . 8
5.5 Freedom from surface defects. 8
5.6 Tolerances on dimensions and form . 8
5.7 Section mass . 8
6 Test procedures . 8
6.1 Sampling . 8
6.1.1 Samples for chemical analysis . 8
6.1.2 Mechanical properties . 8
6.2 Test methods . 8
6.2.1 Chemical composition limit . 8
6.2.2 Hardness testing. 9
6.2.3 Tensile testing . 9
6.2.4 Measurement of dimensions . 9
6.2.5 Surface finish . 9
7 Inspection documents . 9
8 Marking of products . 9
9 Packaging . 9
10 Arbitration . 9
Bibliography . 10
2
---------------------- Page: 4 ----------------------
SIST EN 12020-1:2022
EN 12020-1:2022 (E)
European foreword
This document (EN 12020-1:2022) has been prepared by Technical Committee CEN/TC 132
“Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards
shall be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12020-1:2008.
The following technical modifications have been introduced during the revision:
— Modification of the scope.
The series EN 12020 comprises the following parts under the general title Aluminium and aluminium
alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063:
— Part 1: Technical conditions for inspection and delivery
— Part 2: Tolerances on dimensions and form
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 12020-1:2022
EN 12020-1:2022 (E)
1 Scope
This document specifies technical conditions for inspection and delivery of alloys EN AW-6060
and EN AW-6063 extruded precision profiles manufactured with and without a thermal barrier (see
Figures 1 and 2) and without further surface treatment.
Precision profiles for which this document is applicable are distinguished from extruded profiles for
general applications covered in EN 755-9 by the following characteristics:
— they are designed with mostly uniform wall-thicknesses;
— they are mainly used for mechanical engineering, architectural and automotive (except crash-
elements) applications;
— the maximum weight by meter is 10 kg/m;
— the max. wall-thickness proportion (tmax/tmin) of 3,5.
In the case of profiles, which, due to the complexity of their design are difficult to manufacture and
specify, then special agreements between supplier and purchaser may need to be reached.
NOTE The effect of the thermal barrier material on the dimensional tolerances is covered by EN 12020-2
although the actual thermal barrier material itself is not (see EN 14024).
Key Key
1 CD maximum 350 mm 1 CD maximum 350 mm
2 thermal barriers
Figure 1 — Profile without thermal barrier Figure 2 — Profile containing thermal barrier
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part
3: Chemical composition and form of products
4
---------------------- Page: 6 ----------------------
SIST EN 12020-1:2022
EN 12020-1:2022 (E)
EN 755-1, Aluminium and aluminium alloys - Extruded rod/bar, tube
...
SLOVENSKI STANDARD
oSIST prEN 12020-1:2021
01-marec-2021
Aluminij in aluminijeve zlitine - Precizni iztiskani profili v zlitinah EN AW-6060 in EN
AW-6063 - 1. del: Tehnični pogoji za pregled in dobavo
Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and
EN AW-6063 - Part 1: Technical conditions for inspection and delivery
Aluminium und Aluminiumlegierungen - Stranggepresste Präzisionsprofile aus
Legierungen EN AW-6060 und EN AW-6063 - Teil 1: Technische Lieferbedingungen
Aluminium et alliages d'aluminium - Profilés de précision filés en alliages EN AW-6060 et
EN AW-6063 - Partie 1: Conditions techniques de contrôle et de livraison
Ta slovenski standard je istoveten z: prEN 12020-1
ICS:
77.150.10 Aluminijski izdelki Aluminium products
oSIST prEN 12020-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 12020-1:2021
---------------------- Page: 2 ----------------------
oSIST prEN 12020-1:2021
DRAFT
EUROPEAN STANDARD
prEN 12020-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2021
ICS 77.150.10 Will supersede EN 12020-1:2008
English Version
Aluminium and aluminium alloys - Extruded precision
profiles in alloys EN AW-6060 and EN AW-6063 - Part 1:
Technical conditions for inspection and delivery
Aluminium et alliages d'aluminium - Profilés de Aluminium und Aluminiumlegierungen -
précision filés en alliages EN AW-6060 et EN AW-6063 Stranggepresste Präzisionsprofile aus Legierungen EN
- Partie 1: Conditions techniques de contrôle et de AW-6060 und EN AW-6063 - Teil 1: Technische
livraison Lieferbedingungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 132.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12020-1:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 12020-1:2021
prEN 12020-1:2021 (E)
Contents Page
Foreword . 3
1 Scope . 4
2 Normative references . 5
3 Terms and definitions . 6
4 Ordering information . 6
4.1 General . 6
4.2 Reference to a drawing . 7
5 Requirements . 8
5.1 Production and manufacturing processes . 8
5.2 Quality control . 8
5.3 Chemical composition limit . 8
5.4 Mechanical properties . 9
5.5 Freedom from surface defects . 9
5.6 Tolerances on dimensions and form . 9
5.7 Section mass . 9
6 Test procedures . 9
6.1 Sampling . 9
6.2 Test methods . 9
7 Inspection documents . 10
8 Marking of products . 10
9 Packaging . 10
10 Arbitration . 10
Bibliography . 11
2
---------------------- Page: 4 ----------------------
oSIST prEN 12020-1:2021
prEN 12020-1:2021 (E)
Foreword
This document (prEN 12020-1:2021) has been prepared by Technical Committee CEN/TC 132 “Aluminium
and aluminium alloys”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12020-1:2008.
The following technical modifications have been introduced during the revision:
— Modification of the scope.
EN 12020 comprises the following parts under the general title “Aluminium and aluminium alloys — Extruded
precision profiles in alloys EN AW-6060 and EN AW-6063”:
— Part 1: Technical condition for inspection and delivery
— Part 2: Tolerances on dimensions and form.
3
---------------------- Page: 5 ----------------------
oSIST prEN 12020-1:2021
prEN 12020-1:2021 (E)
1 Scope
This document specifies technical conditions for inspection and delivery of alloys EN AW-6060 and
EN AW-6063 extruded precision profiles manufactured with and without a thermal barrier (see Figures 1 and
2) and without further surface treatment.
Precision profiles covered in this document are distinguished from extruded profiles for general applications
covered in EN 755-9 by the following characteristics:
— they are designed with mostly uniformly wall thicknesses;
— they are mainly used for mechanical engineering, architectural and automotive (except crash-elements)
applications;
— the maximum weight by meter is 10 kg/m;
— the maximum wall thickness proportion (Smax/Smin) is 3,5.
In the case of profiles, which, due to the complexity of their design, are difficult to manufacture and specify,
special agreements between supplier and purchaser may need to be reached.
NOTE The effect of the thermal barrier material on the dimensional tolerances is covered by EN 12020-2 although
the actual thermal barrier material itself is not (see EN 14024).
Key
1 CD maximum 350 mm
Figure 1 — Profile without thermal barrier
4
---------------------- Page: 6 ----------------------
oSIST prEN 12020-1:2021
prEN 12020-1:2021 (E)
Key
1 CD maximum 350 mm
2 thermal barriers
Figure 2 — Profile containing thermal barrier
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 573-3, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 3:
Chemical composition and form of products
EN 755-1, Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 1: Technical
conditions for inspection and delivery
EN 755-2, Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 2: Mechanical
properties
EN 10204, Metallic products — Types of inspection documents
EN 12206-1, Paints and varnishes — Coating of aluminium and aluminium alloys for architectural purposes —
Part 1: Coatings prepared from coating powder
EN 12258-1:2012, Aluminium and aluminium alloys — Terms and definitions — Part 1: General terms
EN 12020-2, Aluminium and aluminium alloys — Extruded precision profiles in alloys EN AW-6060 and EN AW-
6063 — Part 2: Tolerances on dimensions and form
EN 14242, Aluminium and aluminium alloys — Chemical analysis — Inductively coupled plasma optical emission
spectral analysis
EN 14361, Aluminium and aluminium alloys — Chemical analysis — Sampling from metal melts
5
---------------------- Page: 7 ----------------------
oSIST prEN 12020-1:2021
prEN 12020-1:2021 (E)
EN ISO 6506-1, Metallic materials — Brinell ha
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.