iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1636-6:1999

(Main)

Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 6: Practices for installation

Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 6: Practices for installation

This part of prEN 1636 specifies practices for installing piping systems made ofglass-reinforced thermosetting plastics based on unsaturated polyester resin (GRP-UP), with or without a thermoplastic liner, intended to be used for non-pressure drainage and sewerage. It is applicable to RP-UP piping systems for the conveyance of surface water or sewage below ground, at temperatures up to 50 oC.

Kunststoff-Rohrleitungssysteme für drucklose Entwässerungs- und Abwasserleitungen - Glasfaserverstärkte duroplastische Kunststoffe (GFK) auf der Basis von ungesättigtem Polyesterharz (UP) - Teil 6: Verfahren zur Verlegung

Dieser Teil von prEN 1636 legt Verfahren zur Verlegung von Rohrsystemen fest, die aus glasfaserverstärkten duroplastischen Kunststoffen auf der Basis von ungesättigtem Polyesterharz (GFK-UP) hergestellt und dafür vorgesehen sind, für drucklose Entwässerungs- und Abwasserleitungen verwendet zu werden. Er ist anwendbar auf GFK-UP-Rohrsysteme für den Transport von Oberflächenwasser und Abwasser bis zu Temperaturen von 50 °C.

Systemes de canalisations en plastique pour l'évacuation et l'assainissement sans pression - Plastiques thermodurcissables renforcés de verre (PRV) a base de résine de polyester non saturé (UP) - Partie 6: Pratiques de pose

La présente partie de la prEN 1636 prescrit des pratiques pour la pose des systemes de canalisations en plastiques thermodurcissables renforcés de verre a base de résine polyester (PRV-UP), avec ou sans gainage interne (liner) thermoplastique, destinés a etre utilisés dans le domaine de l'évacuation et l'assainissement sans pression. Elle est applicable aux systemes de canalisations PRV-UP pour le transport d'eaux de surface ou d'assainissement sans pression a des températures s'élevant jusqu'a 50 °C.

Cevni sistemi iz polimernih materialov za odpadno vodo, ki delujejo po težnostnem principu - S steklenimi vlakni okrepljeni duromerni materiali (GRP), ki temeljijo na nenasičeni poliestrski smoli (UP) - 6. del: Postopki za vgradnjo

General Information

Status
Withdrawn
Publication Date
30-Jun-1999
Withdrawal Date
30-Apr-2004
ICS
23.040.05 - Pipeline and its parts for external sewage systems
93.030 - External sewage systems
Technical Committee
PCV - Plastic pipes, fittings and valves
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-May-2004
Due Date
01-May-2004
Completion Date
01-May-2004
Directive
89/106/EEC - Construction products
Ref Project
EN 1636-6:1997 - Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 6: Practices for installation

Relations

Replaced By
SIST-TS CEN/TS 14578:2004 - Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GPR) based on unsaturated polyester resin (UP) - Recommended practice for installation
Effective Date
01-May-2004

Buy Standard

EN 1636-6:1999EN 1636-6:1999
PreviousNext
Standard
EN 1636-6:1999
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme für drucklose Entwässerungs- und Abwasserleitungen - Glasfaserverstärkte duroplastische Kunststoffe (GFK) auf der Basis von ungesättigtem Polyesterharz (UP) - Teil 6: Verfahren zur VerlegungSystemes de canalisations en plastique pour l'évacuation et l'assainissement sans pression - Plastiques thermodurcissables renforcés de verre (PRV) a base de résine de polyester non saturé (UP) - Partie 6: Pratiques de posePlastics piping systems for non-pressure drainage and sewerage - Glass-reinfo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST-TS CEN/TS 14632:2023(Main)
Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
CEN/TS 14632:2023

This Technical Specification gives guidance on the assessment of conformity of GRP-UP (glass-reinforced thermosetting resins based on unsaturated polyesters) piping products and assemblies in accordance with EN 1796 and EN 14364 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures. This Technical Specification also gives guidance on the assessment of conformity of GRP-UP manholes and inspection chambers in accordance with prEN 15383. Pipes according to EN 14364 are used for manufacturing the shafts and chamber units. Additional statements as needed to assess the conformity of manholes and inspection chambers are given in Annex F. NOTE 1 It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [3]. NOTE 2 If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 [1], EN 45012 [2] or EN ISO/IEC 17021 [5], as applicable.

  • Technical specification
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14758-1:2023(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
EN 14758-1:2023

This document specifies the requirements for solid-wall pipes and fittings with or without internal and/or external skin, and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
NOTE 1   The skins are made of PP compound without mineral modifier.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this document.
This document covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This document is applicable to PP-MD pipes with or without an integral socket.
NOTE 3   The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 4   Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13.
NOTE 5   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this document, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1401-1:2019+A1:2023(Main + Amendment)
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
EN 1401-1:2019+A1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC U) piping systems in the field of non-pressure underground drainage and sewerage:
- buried in ground outside the building structure (application area code "U"), and
- both buried in ground, within the building structure and outside the building (application area code "UD").
NOTE 1   The intended use is reflected in the marking of products by "U" or "UD".
It also specifies the test parameters for the test methods referred to in this document.
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 13476-2 [1].
This document covers a range of nominal sizes, a range of pipes and fittings series and a range of stiffness classes and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to PVC U pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 16.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1852-1:2018+A1:2022(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
EN 1852-1:2018+A1:2022

This part of EN 1852 specifies the requirements for solid wall pipes with smooth internal and external surfaces extruded from the same compound/formulation throughout the wall, fittings and the system of polypropylene (PP) piping systems intended for use for:
-   non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and
-   non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
This standard covers PP materials without mineral modifiers.
It also specifies the test parameters for the test methods referred to in this standard.
NOTE 1 Solid wall multilayer pipes with different formulation throughout the wall and foamed core pipes are covered by EN 13476-2 [1] (see also CEN ISO/TR 27165 [2]).
This standard covers a range of nominal sizes, and pipe series and gives recommendations concerning colours.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with CEN/TS 1852-2, it is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be connected to pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 14.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 13598-3:2022(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Assessment of conformity
CEN/TS 13598-3:2021

This Technical Specification gives guidance for the assessment of conformity of compounds/formulations, products and assemblies in accordance with Parts 1 and 2 of EN 13598 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE   In order to help the reader, a basic test matrix is given in Annexes A and B.
In conjunction with EN 13598- 1 and -2, this Technical Specification is applicable to ancillary underground drainage fittings including manholes and inspection chambers:
-   for non-pressure underground drainage and sewerage outside the building structure (application area code "U"), reflected in the marking of products by "U", and
-   for non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure (application area code "U"), reflected in the marking of products by "UD".

  • Technical specification
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 23856:2021(Main)
Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin (ISO 23856:2021)
EN ISO 23856:2021

This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply, drainage and sewerage with or without pressure. Types of water supply include, but are not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 11296-4:2018/A1:2021(Amendment)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes - Amendment 1: Updated definitions, marking requirements and procedure for alternative expression of flexural test results (ISO 11296-4:2018/Amd 1:2021)
EN ISO 11296-4:2018/A1:2021

2021-02-11 - TC decision is missing to skip FV.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 1046:2021(Main)
Thermoplastics piping and ducting systems - Outside the building structures for gravity and pressurised systems - Trench installation
CEN/TS 1046:2021

This document gives the recommended practise for underground open trench installation and commissioning of thermoplastics piping systems to be used for the conveyance of water under pressure (in addition to EN 805) and for the discharge of wastewater under gravity (in addition to EN 1610) .
In the field of non-pressure underground drainage and sewerage this is reflected in the marking of products by application code "U" and "UD":
-   outside the building structure (U);
-   both buried in ground within the building structure (application area code "D") and outside the
building (application area code "UD").
This document covers also installation and/or connections to valves, manholes, inspection chambers, gullies and other ancillary components in piping systems.
NOTE 1   Code of practise for pipelines for gas supply is covered by EN 12007-series [21].
NOTE 2   Recommended practices for installation of plastic piping systems for soil and waste discharge within the building structure is covered by CEN/TR 13801 [12].
NOTE 3   Practices for underground installation of rainwater infiltration and storage attenuation systems are covered by CEN/TR 17179 [13].
NOTE 4   It is assumed that additional recommendations and/or requirements are detailed in the individual product standards.
NOTE 5    If non-plastic components are part of the plastic system the manufacturer's instructions should be taken into account.
Requirements and instructions concerning commissioning of systems can be found in EN 805 and EN 1610 and the relevant national and/or local regulations. This document gives specific additional recommendations for commissioning relevant for plastic piping systems.
Attention is drawn to any relevant local and/or national regulations (e.g. health, safety and hygienic requirements).

  • Technical specification
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13476-3:2018+A1:2020(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B
EN 13476-3:2018+A1:2020

This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems.
This part is applicable to pipes and fittings with smooth internal and profiled external surfaces, designated as Type B.
It specifies test methods and test parameters as well as requirements.
This part is applicable to:
a)   structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure, reflected in the marking of products by "U";
b)   structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code "U") and within the building structure (application area code "D"), reflected in the marking of products by "UD".
This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours.
NOTE   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13476-2:2018+A1:2020(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A
EN 13476-2:2018+A1:2020

This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems.
This part is applicable to pipes and fittings with smooth internal and external surfaces, designated as Type A.
It specifies test methods and test parameters as well as requirements.
This part is applicable to:
a)   structured-wall pipes and fittings, which are intended to be used buried underground outside the building structure; reflected in the marking of products by "U";
b)   structured-wall pipes and fittings, which are intended to be used buried underground both outside (application area code "U") and within the building structure (application area code "D"); reflected in the marking of products by "UD".
This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints.
This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours.
NOTE   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day