iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN 13523-10:2023

(Main)

Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

This part of the EN 13523 series specifies the basic principles and procedure for determining the resistance of an organic coating on a metallic substrate (coil coating) to a combination of fluorescent UV radiation, and water condensation and temperature under controlled conditions.
Due to varied conditions which occur during natural weathering and the extreme nature of accelerated testing, correlation between the two cannot be expected.
Not all organic coatings will perform on an equal basis but a degree of correlation between the same generic type might be observed.

Bandbeschichtete Metalle - Prüfverfahren - Teil 10: Beständigkeit gegen UV-Strahlung mit Leuchtstofflampen und Kondensation von Wasser

Tôles prélaquées - Méthodes d'essai - Partie 10 : Résistance à un rayonnement UV fluorescent et à la condensation de l'eau

Le présent document spécifie les principes de base et le mode opératoire à appliquer pour déterminer la résistance d’un revêtement organique appliqué sur un support métallique (prélaquage en bandes continues), à une combinaison d’un rayonnement UV fluorescent, de condensation d’eau et de température, dans des conditions contrôlées.
Compte tenu des diverses conditions qui règnent pendant le processus de vieillissement naturel et de la nature extrême des essais accélérés, aucune corrélation ne peut être escomptée entre les deux.
Tous les revêtements organiques ne se comporteront pas de la même manière, mais un certain degré de corrélation peut apparaître entre ceux de même type générique.

Prevlečene kovine, ki se navijajo - Preskusne metode - 10. del: Odpornost proti fluorescentni ultravijolični svetlobi in kondenzaciji vode

General Information

Status
Not Published
Public Enquiry End Date
02-Oct-2023
ICS
17.180.20 - Colours and measurement of light
25.220.60 - Organic coatings
Technical Committee
IBLP - Paints and varnishes
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
09-Jun-2023
Due Date
27-Oct-2023
Completion Date
13-Oct-2023
Ref Project
EN 13523-10:2024 - Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

Relations

Replaces
SIST EN 13523-10:2017 - Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation
Effective Date
01-Sep-2024

Buy Standard

prEN 13523-10:2023prEN 13523-10:2023
PreviousNext
Draft
prEN 13523-10:2023
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 13523-10:2023
01-september-2023
Prevlečene kovine, ki se navijajo - Preskusne metode - 10. del: Odpornost proti
fluorescentni ultravijolični svetlobi in kondenzaciji vode
Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and
water condensation
Bandbeschichtete Metalle - Prüfverfahren - Teil 10: Beständigkeit gegen UV-Strahlung
mit Leuchtstofflampen und Kondensation von Wasser
Tôles prélaquées - Méthodes d'essai - Partie 10 : Résistance à un rayonnement UV
fluorescent et à la condensation de l'eau
Ta slovenski standard je istoveten z: prEN 13523-10
ICS:
17.180.20 Barve in merjenje svetlobe Colours and measurement of
light
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-10:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13523-10:2023

---------------------- Page: 2 ----------------------
oSIST prEN 13523-10:2023


DRAFT
EUROPEAN STANDARD
prEN 13523-10
NORME EUROPÉENNE

EUROPÄISCHE NORM

July 2023
ICS 25.220.60 Will supersede EN 13523-10:2017
English Version

Coil coated metals - Test methods - Part 10: Resistance to
fluorescent UV radiation and water condensation
Tôles prélaquées - Méthodes d'essai - Partie 10 : Bandbeschichtete Metalle - Prüfverfahren - Teil 10:
Résistance à un rayonnement UV fluorescent et à la Beständigkeit gegen UV-Strahlung mit
condensation de l'eau Leuchtstofflampen und Kondensation von Wasser
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-10:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13523-10:2023
prEN 13523-10:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus and materials . 6
6 Sampling . 6
7 Test panels . 6
8 Procedure . 6
8.1 Exposure .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 13523-23:2023(Main)
Coil coated metals - Test methods - Part 23: Resistance to humid atmospheres containing sulfur dioxide
EN 13523-23:2023

This Part of EN 13523 describes the procedure for determining the colour stability of an organic coating on a metallic substrate when exposed to humid atmospheres containing sulfur dioxide. This method has been designed to provide an accelerated test for evaluating the colour fastness of coil coated products in atmospheres containing sulfur dioxide (typical of industrial atmospheres).

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-3:2021(Main)
Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison
EN 13523-3:2021

This part of EN 13523 specifies procedures for determining the instrumental colour difference (CIELAB) of an organic coating on a metallic substrate.
Establishing a standard as well as the magnitude of an acceptable colour difference are not covered by this method.
Two appropriate methods are given in this part of EN 13523:
a)   instrumental colour difference measurement using a tristimulus colorimeter;
b)   instrumental colour difference measurement using a spectrophotometer or equivalent.
Care shall be taken when measuring e.g.
-   textured surfaces;
-   fluorescent coatings;
-   metameric coatings;
-   multi-coloured, pearlescent, metallic or special colour effect coatings.
In order to determine whether metamerism is present, the metamerism index is determined (see EN 13523-15) and/or a visual examination (see EN 13523-22) is performed with different artificial light sources.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-22:2017(Main)
Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison
EN 13523-22:2017

This part of EN 13523 specifies the procedure for determining the difference in the colour of an organic coating on a metallic substrate by visual comparison against a standard using either diffuse natural daylight or artificial daylight in a standard booth.
NOTE 1   Results might differ between natural and artificial daylight.
It might be that two colour specimens will match in daylight but not under another light source. This phenomenon is known as metamerism (see EN 13523-15).
NOTE 2   If metameric match is to be reported in objective terms, spectrophotometric measurements (using CIE Standard Illuminants D65 and A) should be made, in accordance with EN 13523-15.
No statement is made about either the precision or the accuracy of this procedure since the results derived are neither in numerical form nor do they provide a pass/fail evaluation in objective terms. Therefore, this procedure should only be used where the use of colour measuring instruments is not recommendable (evaluation of colour matches, inspection of metallic colours, etc.).
The standardization of such visual comparisons, by light sources, illuminating and viewing geometry and specimen size, provides for improved uniformity of results. This practice is essential for critical colour matching and is highly recommended for colour inspections.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-10:2017(Main)
Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation
EN 13523-10:2017

This part of EN 13523 specifies the basic principles and procedure for determining the resistance of an organic coating on a metallic substrate (coil coating) to a combination of fluorescent UV radiation, and water condensation and temperature under controlled conditions.
Due to varied conditions which occur during natural weathering and the extreme nature of accelerated testing, correlation between the two cannot be expected.
Not all organic coatings will perform on an equal basis but a degree of correlation between the same generic type might be observed.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 13523-3:2023(Main)
Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison
EN 13523-3:2024

This document specifies procedures for determining the instrumental colour difference (CIELAB) of an organic coating on a metallic substrate compared to another one used as a reference (usually called reference) and the metamerism depending on the illuminant.
When two colour specimens have identical spectral reflectance curves, they are matching under any illuminant irrespective of its spectral characteristics. This is termed a “spectral match”. It is also possible for two colour specimens having different spectral reflectance curves to match visually under a given light source but not to match under another light source with different spectral characteristics; such matches are termed “metameric”.
One quantitative description of metamerism is the so-called “metamerism index”.
Information on the metamerism index is of limited value where ΔE (instrumental colour difference for a given illuminant) is > 0,5. The metamerism index is not suited for determining the absolute colour difference or colour consistency of a given specimen at change of illuminant.
The colour difference under the reference illuminant is to be measured in colour coordinates L*, a* and b*.
Excluded from this method are organic coatings producing fluorescence and/or which are multicoloured, pearlescent or metallic.
Establishing a reference as well as the magnitude of an acceptable colour difference are not covered by this method.
Two methods are given in this document:
a)   instrumental colour difference measurement using a tristimulus colourimeter;
b)   instrumental colour difference measurement using a spectrophotometer or equivalent.
It is advised that care is taken when measuring e.g.
—   textured surfaces;
—   fluorescent coatings;
—   metameric coatings;
—   multi-coloured, pearlescent, metallic or special colour effect coatings.

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 13523-22:2023(Main)
Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison
EN 13523-22:2024

This part of the EN 13523 series specifies the procedure for determining the difference in the colour of an organic coating on a metallic substrate by visual comparison against a standard using either diffuse natural daylight or artificial daylight in a standard booth.
NOTE   Results might differ between natural and artificial daylight.
It might be that two colour specimens will match in daylight but not under another light source. This phenomenon is known as metamerism (see EN 13523 15).
If a metameric match is to be reported in objective terms, spectrophotometric measurements (using CIE Standard Illuminants D65 and A) should be made, in accordance with EN 13523-15.
No statement is made about either the precision or the accuracy of this procedure since the results derived are neither in numerical form nor do they provide a pass/fail evaluation in objective terms. Therefore, this procedure should only be used where the use of colour measuring instruments is not recommendable (evaluation of colour matches, inspection of metallic colours, etc.).
The standardization of such visual comparisons, by light sources, illuminating and viewing geometry and specimen size, provides for improved uniformity of results. This practice is essential for critical colour matching and is highly recommended for colour inspections.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-23:2023(Main)
Coil coated metals - Test methods - Part 23: Resistance to humid atmospheres containing sulfur dioxide
EN 13523-23:2023

This Part of EN 13523 describes the procedure for determining the colour stability of an organic coating on a metallic substrate when exposed to humid atmospheres containing sulfur dioxide. This method has been designed to provide an accelerated test for evaluating the colour fastness of coil coated products in atmospheres containing sulfur dioxide (typical of industrial atmospheres).

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-3:2021(Main)
Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental comparison
EN 13523-3:2021

This part of EN 13523 specifies procedures for determining the instrumental colour difference (CIELAB) of an organic coating on a metallic substrate.
Establishing a standard as well as the magnitude of an acceptable colour difference are not covered by this method.
Two appropriate methods are given in this part of EN 13523:
a)   instrumental colour difference measurement using a tristimulus colorimeter;
b)   instrumental colour difference measurement using a spectrophotometer or equivalent.
Care shall be taken when measuring e.g.
-   textured surfaces;
-   fluorescent coatings;
-   metameric coatings;
-   multi-coloured, pearlescent, metallic or special colour effect coatings.
In order to determine whether metamerism is present, the metamerism index is determined (see EN 13523-15) and/or a visual examination (see EN 13523-22) is performed with different artificial light sources.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-10:2017(Main)
Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation
EN 13523-10:2017

This part of EN 13523 specifies the basic principles and procedure for determining the resistance of an organic coating on a metallic substrate (coil coating) to a combination of fluorescent UV radiation, and water condensation and temperature under controlled conditions.
Due to varied conditions which occur during natural weathering and the extreme nature of accelerated testing, correlation between the two cannot be expected.
Not all organic coatings will perform on an equal basis but a degree of correlation between the same generic type might be observed.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13523-22:2017(Main)
Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison
EN 13523-22:2017

This part of EN 13523 specifies the procedure for determining the difference in the colour of an organic coating on a metallic substrate by visual comparison against a standard using either diffuse natural daylight or artificial daylight in a standard booth.
NOTE 1   Results might differ between natural and artificial daylight.
It might be that two colour specimens will match in daylight but not under another light source. This phenomenon is known as metamerism (see EN 13523-15).
NOTE 2   If metameric match is to be reported in objective terms, spectrophotometric measurements (using CIE Standard Illuminants D65 and A) should be made, in accordance with EN 13523-15.
No statement is made about either the precision or the accuracy of this procedure since the results derived are neither in numerical form nor do they provide a pass/fail evaluation in objective terms. Therefore, this procedure should only be used where the use of colour measuring instruments is not recommendable (evaluation of colour matches, inspection of metallic colours, etc.).
The standardization of such visual comparisons, by light sources, illuminating and viewing geometry and specimen size, provides for improved uniformity of results. This practice is essential for critical colour matching and is highly recommended for colour inspections.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day