Shower trays for domestic purposes

This European Standard specifies requirements, test methods and procedures for evaluation of conformity for shower trays used for domestic purposes which ensure that the product, when installed, used and maintained in accordance with the manufacturer's instructions, will satisfy cleanability and durability" when used for personal hygiene. This standard is applicable to all sizes and shapes of shower trays.

Duschwannen für den Hausgebrauch

Diese Europäische Norm legt Anforderungen, Prüfverfahren sowie Verfahren zur Bewertung der Konformität für Duschwannen für den Hausgebrauch fest, die sicherstellen, dass das in Übereinstimmung mit den Herstelleranweisungen eingebaute, genutzte und gepflegte Produkt für die Nutzung zur persönlichen Hygiene eine zufrieden stellende Reinigbarkeit und !Dauerhaftigkeit" aufweist.
Diese Norm ist auf alle Größen und Formen von Duschwannen anwendbar.
Diese Norm gilt nicht für Duschwannen für spezielle medizinische Anwendungen.
ANMERKUNG 1   Der Begriff „für den Hausgebrauch“ in dieser Norm schließt die Verwendung in Hotels, Studentenwohnheimen, Krankenhäusern und ähnlichen Einrichtungen ein.
ANMERKUNG 2   Anhang A führt Eigenschaften von Werkstoffen auf, die üblicherweise für die Herstellung von Duschwannen eingesetzt werden.

Receveurs de douche à usage domestique

La présente Norme européenne spécifie les prescriptions, méthodes d’essai et modes opératoires d’évaluation de la conformité des receveurs de douche à usage domestique, visant à garantir que le produit, s’il est installé, utilisé et entretenu selon les instructions du fabricant, présente les qualités requises !texte supprimé", dans le cadre d’une utilisation d’hygiène personnelle.
La présente norme s’applique à toutes les tailles et formes de receveurs de douche.
La présente norme ne traite pas des receveurs de douche utilisés dans le cadre de soins médicaux.
NOTE 1   Pour les besoins de la présente norme, le terme «à usage domestique» inclut l’utilisation en hôtels, en logements pour étudiants, en hôpitaux et autres bâtiments similaires.
NOTE 2   L’Annexe A donne les caractéristiques des matériaux couramment utilisés pour la fabrication des receveurs de douche.

Kadi za prhanje za domačo uporabo

Ta evropski standard določa zahteve, preskusne metode in postopke za ocenjevanje skladnosti kadi za prhanje za domačo uporabo in osebno higieno, ki zagotavljajo, da bo proizvod, nameščen in vzdrževan v skladu z navodili proizvajalca, izpolnjeval zahteve po zmožnosti čiščenja in trajnosti pri uporabi za osebno higieno. Ta standard velja za vse velikosti in oblike kadi za prhanje.

General Information

Status
Withdrawn
Publication Date
02-Sep-2010
Withdrawal Date
15-Aug-2016
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
02-Aug-2016
Due Date
25-Aug-2016
Completion Date
16-Aug-2016

Relations

Effective Date
01-Oct-2010
Effective Date
18-Jan-2023
Effective Date
19-Jan-2023

Buy Standard

Standard
EN 14527:2006+A1:2010
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Duschwannen für den HausgebrauchReceveurs de douche à usage domestiqueShower trays for domestic purposes91.140.70Sanitarne napraveSanitary installationsICS:Ta slovenski standard je istoveten z:EN 14527:2006+A1:2010SIST EN 14527:2006+A1:2010en,fr,de01-oktober-2010SIST EN 14527:2006+A1:2010SLOVENSKI
STANDARD



SIST EN 14527:2006+A1:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14527:2006+A1
July 2010 ICS 91.140.70 Supersedes EN 14527:2006English Version
Shower trays for domestic purposes
Receveurs de douche à usage domestique
Duschwannen für den Hausgebrauch This European Standard was approved by CEN on 14 December 2005 and includes Amendment 1 approved by CEN on 19 June 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14527:2006+A1:2010: ESIST EN 14527:2006+A1:2010



EN 14527:2006+A1:2010 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Terms and definitions .44Classification .55!!!!Requirements for class 1 products"""" .55.1General .55.2Cleanability .55.3!!!!Durability"""" .56Requirements for class 2 products.77Dangerous substances .78Test methods .88.1Stability of the bottom of the shower tray .88.2Chemical resistance .88.3Resistance to temperature changes . 109Marking, labelling and packaging . 1110Evaluation of conformity . 1210.1General . 1210.2Type testing . 1210.3Factory production control . 13Annex A (informative)
Materials . 15Annex B (informative)
Surface of shower trays . 17Annex ZA (informative)
!!!!Clauses of this European Standard addressing the provisions of the EU Construction Products Directive"""" . 18Bibliography . 23 SIST EN 14527:2006+A1:2010



EN 14527:2006+A1:2010 (E) 3 Foreword This document (EN 14527:2006+A1:2010) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2011, and conflicting national standards shall be withdrawn at the latest by April 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-06-19. This document supersedes EN 14527:2006. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. .SIST EN 14527:2006+A1:2010



EN 14527:2006+A1:2010 (E) 4 1 Scope This European Standard specifies requirements, test methods and procedures for evaluation of conformity for shower trays used for domestic purposes which ensure that the product, when installed, used and maintained in accordance with the manufacturer's instructions, will satisfy cleanability and !durability" when used for personal hygiene. This standard is applicable to all sizes and shapes of shower trays. This standard does not cover shower trays for use with medical provisions. NOTE 1 For the purpose of this standard the term "domestic purposes" includes use in hotels, accommodation for students, hospitals and similar buildings. NOTE 2 Annex A lists characteristics of materials commonly used for manufacturing shower trays. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 251, Shower trays — Connecting dimensions EN 14483-1, Vitreous and porcelain enamels — Determination of resistance to chemical corrosion — Part 1: Determination of resistance to chemical corrosion by acids at room temperature ISO 2722, Vitreous and porcelain enamels — Determination of resistance to citric acid at room temperature ISO 2742, Vitreous and porcelain enamels — Determination of resistance to boiling citric acid ISO 2744, Vitreous and porcelain enamels — Determination of resistance to boiling water and water vapour ISO 4533, Vitreous and porcelain enamels — Determination of resistance to hot detergent solutions used for washing textiles 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 shower tray sanitary appliance that collects the water from washing of the human body under a shower and directs it to a waste outlet 3.2 cleanability characteristics which allow the surface intended to come into contact with water to be non-absorbent and readily kept visually free from dirt and/or stains when subject to a maintenance regime which may include, when appropriate, specific instructions for use and care specified by the manufacturer ! SIST EN 14527:2006+A1:2010



EN 14527:2006+A1:2010 (E) 5 3.3 durability attributes of materials and their surfaces intended to come into contact with water, which allow the anticipated working life of the product" ! 4 Classification Class 1: Products complying with the requirements of Clause 5 Class 2: Products complying with the requirements of Clause 6" ! 5 Requirements for class 1 products"""" 5.1 General The manufacturer shall provide instructions with each shower tray covering installation and care. NOTE Annex B gives advice which manufacturers can include in their instructions. 5.2 Cleanability 5.2.1 Appearance of surface When a shower tray is inspected under strong and oblique illumination, the surfaces intended to come into contact with water shall be visibly smooth, non-absorbent and free from inaccessible corners that would impair cleanability. NOTE Surfaces with cracks, chips, crazing and other similar defects are not considered to be smooth. 5.2.2 Drainage of water Shower trays shall have at least one waste outlet hole. The dimensions of the waste outlet hole shall comply with the requirements of EN 251. Other dimensions are permissible, if the manufacturer provides or recommends a suitable waste fitting. All water shall empty from the shower tray unless prevented by surface tension. 5.3 !!!!Durability"""" 5.3.1 General Conformance with the requirements of !5.3.2 to 5.3.4" give an assurance of !durability". 5.3.2 Stability of bottom When tested in accordance with !8.1", there shall be no permanent distortion or other defects, e.g. cracks, such that the requirements of !5.2.2" are not satisfied. SIST EN 14527:2006+A1:2010



EN 14527:2006+A1:2010 (E) 6 5.3.3 Resistance to chemicals and staining agents 5.3.3.1 General When shower trays, other than those made from the materials specified in !5.3.3.2", are tested in accordance with !8.2", the surface finish shall be unaffected by the chemicals and staining agents specified in Table 1 except for superficial surface changes which are removable with water or with water and the specified abrasive agent. Table 1 — Chemicals and staining agents Family Product Acids Acetic acid (CH3COOH), 10 % V/V Alkalines Sodium hydroxide (NaOH), 5 % m/m Alcohols Ethanol (C2H5OH), 70 % V/V Bleaches Sodium hypochlorite (NaOCI), 5 % active chlorine (CI2) a
Staining agents Methylene blue, 1 % m/m a The above specified bleach may be replaced by sodium percarbonate (2Na2CO3 · 3H2O2) prepared as follows: Dissolve 1 g of a commercial available powdery bleach based on sodium percarbonate containing 15 % to 30 % of the active component in 100 ml de-ionised water at room temperature.
5.3.3.2 Particular requirements for shower trays made of enamelled steel and enamelled cast iron Shower trays made from enamelled steel and enamelled cast iron shall comply with the requirements given in Table 2. Table 2 — Requirements for shower trays made of enamelled steel and enamelled cast iron Requirement Parameter Test method Resistance to boiling water < 10 g/m2 ISO 2744 Resistance to cold citric acid Class 2 ISO 2722 Resistance to boiling citric acid < 5 g/m² ISO 2742 Resistance to cold sulphuric acid Class 2 EN 14483-1 Resistance to alkali solutions < 8 g/m² Test apparatus according to ISO 2742 Test solution according to ISO 4533 Duration of test: 2,5 h
5.3.4 Resistance to temperature changes When tested in accordance with !8.3", all shower trays shall show no evidence of distortion or other defects, e.g. crazing, which will impair their cleanability. Experience has shown that shower trays manufactured from the stainless steel grades listed in annex A, enamelled steel, enamelled cast iron and glazed ceramics comply with this requirement. !deleted text" SIST EN 14527:2006+A1:2010



EN 14527:2006+A1:2010 (E) 7
! 6 Requirements for class 2 products 6.1 General The manufacturer shall provide instructions with each shower tray covering installation and care. NOTE Annex B gives advice which manufacturers can include in their instructions. 6.2 Cleanability 6.2.1 Appearance of surface When a shower tray is inspected under strong and oblique illumination, the surfaces intended to come into contact with water shall be visibly smooth, non-absorbent and free from inaccessible corners that would impair the cleanability.
NOTE Surfaces with cracks, chips, crazing and other similar defects are not considered to be smooth. 6.2.2 Drainage of water Shower trays shall have at least one waste outlet hole. The dimensions of the waste outlet hole shall comply with the requirements of EN 251. Other dimensions are permissible, if the manufacturer provides or recommends a suitable waste fitting. All water shall empty from the shower tray unless prevented by surface tension. 6.3 Durability 6.3.1 General Shower trays shall be readily cleanable for their anticipated working life when normal cleaning and maintenance is carried out. 6.3.2 Materials Experience has shown that shower trays made from plastics materials, enamelled steel, enamelled cast iron, stainless steel, glazed ceramics or glass and their surfaces intended to come into contact with water have the properties described in 6.3.1." ! 7 Dangerous substances NOTE See Annex ZA, ZA.1 and ZA.3." SIST EN 14527:2006+A1:2010



EN 14527:2006+A1:2010 (E) 8 8 Test methods 8.1 Stability of the bottom of the shower tray 8.1.1 Test apparatus  an adequate number of reinforced cloth bags each with dimensions of approximately 500 mm x 200 mm filled with lead shot, iron shot or sand of a mass of 25 5,00+ kg or 12,5 5,00+ kg. 8.1.2 Determination of the load The load to be applied for the test shall comprise the adequate number of cloth bags (see !8.1.1") equating to 100 kg. 8.1.3 Procedure  Install the shower tray in accordance with the manufacturer's installation instructions.  Position the adequate number of bags in the geometric centre of shower tray as shown in Figure 1.
Figure 1 — Load application  Leave the load for 10 10+ min.  On completion of the tests remove all the bags.  After 10 10+ min verify that the shower tray complies with !5.3.2" by pouring copious amounts of water coloured in contrast with that of the shower tray around all the inner surface of the sides of the showering area. 8.2 Chemical resistance 8.2.1 Principle The test is intended to give an indication of the effect of commonly used household chemicals, staining agents and cleansing agents. 8.2.2 Test apparatus and chemicals a) chemicals and stains A list of chemicals and stains to be used is specified in Table 1. Each chemical solution shall be prepared immediately before use with de-ionised water, and it shall be applied at a temperature (23 ± 5) °C. b) borosilicate watch glasses: 40 mm nominal diameter; SIST EN 14527:2006+A1:2010



EN 14527:2006+A1:2010 (E) 9 c) pipettes; d) cleaning device; A typical cleaning device is shown in Figure 2. It consists of a disc of 75 mm diameter, faced with synthetic flexible open cell foam 15 mm in thickness. The device is driven by means of a square axle which fits loosely into the device. Any device having a mass of (1000 ± 50) g can be used. e) Abrasive comprising 12 h-alumina (suspension of aluminium oxide in water)1).
Key 1 square axle (a = b – 1 mm) 2 disc faced with foam Figure 2 — Cleaning device 8.2.3 Test specimens Carry out the tests on the bottom, and on a flat part of the wall of the shower tray or on test specimens cut from these areas. 8.2.4 Procedure  Select an area to be tested.  Use each test area only once for each application. Clean the test area thoroughly with hot soapy water, rinse and wipe dry with a clean dry cloth.  At each of the test areas deposit a drop of the test solution. Cover the drop with a watch glass concave face downwards. The drop size shall be such that it is completely covered by the watch glass. Leave for (120 ± 5) min with the test area protected from sunlight.
1) A suitable product is available from MERCK Eurolab-Prolabo, 54 rue Roger Salengro, 94126 Fontenay sous Bois CEDEX, France, as DURMAXTM under product description N° 20993. This information is given for the convenience of users of this standard and does not constitute an endorsement by CEN of this product. SIST EN 14527:2006+A1:2010



EN 14527:2006+A1:2010 (E) 10  Thoroughly rinse the test areas with de-ionised water and visually check for any adverse change in appearance. If any deterioration is noticed, dip the foam disc in de-ionised water and place it on the surface that was tested.
Rotate the cleaning device at a speed of 60 min-1. Clean for 30 revolutions.  Rinse with de-ionised water, dry and visually re-examine the test areas. If any deterioration persists, repeat the cleaning process using the abrasive comprising 12 h-aluminia su
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.