kSIST FprEN ISO 28017:2025

Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (ISO/FDIS 28017:2025)

This document specifies requirements for two types, seven classes and three grades of wire- or textile-reinforced dredging hoses with nominal sizes ranging from 100 to 1 300. Within each class, all grades and sizes have the same maximum working pressure. Such hoses are suitable for the delivery or suction of seawater or freshwater mixed with silt, sand, coral and small stones with a specific gravity in the range from 1,0 to 2,3 at ambient temperature ranging from -10 °C to +40 °C or for low-temperature hoses (designated -LT) ranging from -20 °C to +40 °C. This document covers two types of hose, as follows:
—    type 1: floating type, for delivery only, which includes flotation material to give the hose buoyancy;
—    type 2: submarine type for delivery and suction.
This document does not specify requirements concerning the service life of hoses or hose assemblies. Specifying such requirements is the responsibility of the customer, in consultation with the hose manufacturer.

Gummischläuche und Schlauchleitungen, draht- oder textilverstärkt für Nassbaggeranwendungen - Anforderung (ISO/FDIS 28017:2025)

Dieses Dokument legt Anforderungen für zwei Typen, sieben Klassen und drei Unterklassen von draht- oder textilverstärkten Nassbaggerschläuchen mit einer Nennweite von 100 bis 1 300 fest. Derartige Schläuche sind geeignet für die Förderung oder das Ansaugen von Meerwasser oder Süßwasser vermischt mit Schlick, Korallen und kleinen Steinen mit einer Dichte zwischen 1,0 und 2,3 bei Umgebungstemperaturen von −10 °C bis zu +40 °C bzw. bei Niedrigtemperaturschläuchen (mit der Bezeichnung -LT) von −20 °C bis zu +40 °C.
Dieses Dokument umfasst zwei Arten von Schläuchen, wie folgt:
   Typ 1: Schwimmtyp, nur zur Förderung, welcher Schwimmmaterial enthält, das für den Auftrieb des Schlauches sorgt;
   Typ 2: Unterwassertyp zur Förderung und Ansaugung.

Tuyaux et flexibles en caoutchouc, à armature textile ou métallique, pour des applications de dragage - Spécifications (ISO/FDIS 28017:2025)

ISO 28017:2018 spécifie les exigences pour deux types, sept classes et trois qualités de tuyaux de dragage à armature métallique ou textile, de dimensions nominales allant de 100 à 1 200. Dans chaque classe, toutes les qualités et dimensions ont la même pression maximale de service. Ces tuyaux sont adaptés pour le refoulement ou l'aspiration d'eau de mer ou d'eau douce mélangée à du limon, du sable, des coraux et de petites pierres ayant une densité relative de 1,0 à 2,3 à des températures ambiantes comprises entre −10 °C et +40 °C.
ISO 28017:2018 traite les deux types de tuyaux suivants:
- type 1: type flottant, pour le refoulement uniquement, incluant un matériau de flottaison permettant au tuyau de flotter;
- type 2: type sous-marin, pour le refoulement ou l'aspiration.
ISO 28017:2018 ne spécifie pas d'exigences concernant la durée de vie des tuyaux ou des flexibles. La spécification de ce type d'exigences relève de la responsabilité du client, en concertation avec le fabricant de tuyaux.

Gumene cevi in cevni priključki, ojačeni z žicami ali tekstilom, za uporabo v vodnem bagru - Specifikacija (ISO/FDIS 28017:2025)

General Information

• Status: Not Published
• Public Enquiry End Date: 20-Apr-2025
• ICS: 53.100 - Earth-moving machinery
• ICS: 83.140.40 - Hoses
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 5020 - Formal vote (FV) (Adopted Project)
• Start Date: 09-Dec-2025
• Due Date: 27-Jan-2026
• Completion Date: 10-Dec-2025
• Ref Project: FprEN ISO 28017 - Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (ISO/FDIS 28017:2025)

Relations

• Revises: SIST EN ISO 28017:2018 - Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications - Specification (ISO 28017:2018)
• Effective Date: 01-May-2024

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 28017:2025
01-april-2025
Gumene cevi in cevni priključki, ojačeni z žicami ali tekstilom, za uporabo v
vodnem bagru - Specifikacija (ISO/DIS 28017:2025)
Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications -
Specification (ISO/DIS 28017:2025)
Gummischläuche und Schlauchleitungen, draht- oder textilverstärkt für
Nassbaggeranwendungen - Anforderung (ISO/DIS 28017:2025)
Tuyaux et flexibles en caoutchouc, à armature textile ou métallique, pour des
applications de dragage - Spécifications (ISO/DIS 28017:2025)
Ta slovenski standard je istoveten z: prEN ISO 28017
ICS:
53.100 Stroji za zemeljska dela Earth-moving machinery
83.140.40 Gumene cevi Hoses
oSIST prEN ISO 28017:2025 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN ISO 28017:2025
oSIST prEN ISO 28017:2025
DRAFT
International
Standard
ISO/DIS 28017
ISO/TC 45/SC 1
Rubber hoses and hose assemblies,
Secretariat: DIN
wire or textile reinforced,
Voting begins on:
for dredging applications —
2025-01-27
Specification
Voting terminates on:
2025-04-21
Tuyaux et flexibles en caoutchouc, à armature textile ou
métallique, pour des applications de dragage — Spécifications
ICS: 23.040.70
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 28017:2025(en)
oSIST prEN ISO 28017:2025
DRAFT
ISO/DIS 28017:2025(en)
International
Standard
ISO/DIS 28017
ISO/TC 45/SC 1
Rubber hoses and hose assemblies,
Secretariat: DIN
wire or textile reinforced,
Voting begins on:
for dredging applications —
Specification
Voting terminates on:
Tuyaux et flexibles en caoutchouc, à armature textile ou
métallique, pour des applications de dragage — Spécifications
ICS: 23.040.70
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2025
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: [phone]
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: [e-mail]
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 28017:2025(en)
ii
oSIST prEN ISO 28017:2025
ISO/DIS 28017:2025(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification . 2
4.1 Classes .2
4.2 Grades .3
5 Materials and construction . 3
5.1 Hoses .3
5.2 Flotation material .4
5.3 End fittings and end connections .4
6 Dimension and tolerances . 4
6.1 Diameters .4
6.2 Hose assembly length .5
7 Physical properties . 5
7.1 Rubber compounds .5
7.1.1 Abrasion resistance of lining .5
7.1.2 Tear strength of lining .5
7.1.3 Rebound resilience of lining .5
7.1.4 Ozone resistance of cover .6
7.1.5 Low-temperature brittleness of lining and cover .6
7.2 Performance requirements .6
7.2.1 Hydrostatic requirements .6
7.2.2 Change in length .7
7.2.3 Bending test .7
7.2.4 Leakage of hose assemblies (proof pressure test) .7
7.2.5 Minimum reserve buoyancy .7
7.2.6 Flotation material recovery .8
7.2.7 Adhesion between components .8
7.2.8 Adhesion between end fitting and lining .8
7.2.9 Minimum tensile strength of empty hose assemblies . .9
7.2.10 Vacuum resistance .9
7.2.11 Dimensions of flange and other connections .9
7.2.12 Visual examination .9
7.3 Frequency of testing .9
8 Test certificate or report . 9
9 Marking . .10
10 Recommendations for packaging and storage . 10
Annex A (normative) Type tests and routine tests .11
Annex B (normative) Measurement of adhesion between end fitting and lining.12
Annex C (normative) Hose assembly tensile-strength test .15
Bibliography .18

iii
oSIST prEN ISO 28017:2025
ISO/DIS 28017:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL:
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies.
This forth edition cancels and replaces the third edition (ISO 28017:2018), which has been technically
revised.
The main changes compared to previous edition are as follows:
— in Clause 1, extend the ambient temperature range from “−20 °C to +40 °C”;
— Clause 2 has been updated;
— in Table 1, add a nominal size of 1 300;
— in 7.1.5, add low-temperature brittleness of lining compound for the hoses with working temperature
below -10 °C.
iv
oSIST prEN ISO 28017:2025
DRAFT International Standard ISO/DIS 28017:2025(en)
Rubber hoses and hose assemblies, wire or textile reinforced,
for dredging applications — Specification
1 Scope
This document specifies requirements for two types, seven classes and three grades of wire- or textile-
reinforced dredging hoses with nominal sizes ranging from 100 to 1 300. Within each class, all grades
and sizes have the same maximum working pressure. Such hoses are suitable for the delivery or suction of
seawater or freshwater mixed with silt, sand, coral and small stones with a specific gravity in the range from
1,0 to 2,3 at ambient temperature ranging from -10 °C to +40 °C or for low-temperature hoses (designated
-LT) ranging from -20 °C to +40 °C. This document covers two types of hose, as follows:
— type 1: floating type, for delivery only, which includes flotation material to give the hose buoyancy;
— type 2: submarine type for delivery and suction.
This document does not specify requirements concerning the service life of hoses or hose assemblies.
Specifying such requirements is the responsibility of the customer, in consultation with the hose
manufacturer.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 34-2:2022, Rubber, vulcanized or thermoplastic — Determination of tear strength — Part 2: Small (Delft)
test pieces
ISO 812, Rubber, vulcanized or thermoplastic — Determination of low-temperature brittleness
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1431-1, Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and dynamic
strain testing
ISO 4649:2017, Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating
cylindrical drum device
ISO 4662:2017, Rubber, vulcanized or thermoplastic — Determination of rebound resilience
ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of hoses
and the lengths of hose assemblies
ISO 7233:2021, Rubber and plastics hoses and hose assemblies — Determination of resistance to vacuum
ISO 8033, Rubber and plastics hoses — Determination of adhesion between components
ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
ISO 10619-1, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — Part 1: Bending
tests at ambient temperature
oSIST prEN ISO 28017:2025
ISO/DIS 28017:2025(en)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https:// www .electropedia .org/
— ISO Online browsing platform: available at https:// www .iso .org/ obp
4 Classification
4.1 Classes
Seven classes of hose are specified, distinguished by their maximum working pressure, of nominal sizes
from 100 to 1 300, as shown in Table 1.
Table 1 — Classes and corresponding maximum working pressures and nominal sizes
Class
5 10 15 20 25 30 40
Maximum working pressure, MWP
Nominal size bar
5 10 15 20 25 30 40
MPa
0,5 1,0 1,5 2,0 2,5 3,0 4,0
100 X X X X X X X
150 X X X X X X X
200 X X X X X X X
250 X X X X X X N/A
300 X X X X X X N/A
350 X X X X X X N/A
400 X X X X X X N/A
450 X X X X X X N/A
500 X X X X X X N/A
550 X X X X X X N/A
600 X X X X X X N/A
650 X X X X X X N/A
700 X X X X X X N/A
750 X X X X X X N/A
800 X X X X X X N/A
850 X X X X X X N/A
900 X X X X X X N/A
1 000 X X X X X X N/A
1 100 X X X X X X N/A
1 200 X X X X X N/A N/A
1 300 X X X X N/A N/A N/A
X: Applicable
N/A: Not applicable
oSIST prEN ISO 28017:2025
ISO/DIS 28017:2025(en)
4.2 Grades
Type 2 hoses are classified into three grades, A, B and C, according to their construction (number of
reinforcing helical wires), as shown in Table 2.
Type 1 hoses are not divided into grades.
Table 2 — Grades
Construction and purpose
Type Grade
Number of reinforcing
Purpose
wires
1 — 0 Delivery only
A 2 Delivery or suction
2 B 1 Delivery or suction
C 0 Delivery only
The types and grades available in each class (i.e. for each maximum working pressure) are as shown in
Table 3.
Table 3 — Types and grades available in each class
Class
5 10 15 20 25 30 40
Maximum working pressure, MWP
Type Grade bar
5 10 15 20 25 30 40
MPa
0,5 1,0 1,5 2,0 2,5 3,0 4,0
1 — X X X X X X X
A X X X N/A N/A N/A N/A
2 B X X X N/A N/A N/A N/A
C X X X X X X X
X: Applicable
N/A: Not applicable
5 Materials and construction
5.1 Hoses
Type 1 hose assemblies shall consist of an abrasion-resistant rubber lining, one or more layers of steel
or textile reinforcement, a textile-reinforced rubber undercover, a flexible closed-cell flotation material
integrally fitted round the hose body as described in 5.2, an abrasion- and weather-resistant rubber or
thermoplastic outer cover (which, in the case of a rubber cover, can include one or two textile breaker layers),
and end fittings as described in 5.3 on both ends.
Type 2 hose assemblies shall consist of an abrasion-resistant rubber lining, one or more layers of steel or
textile reinforcement, a textile-reinforced rubber, full rubber or thermoplastic cover at least 6 mm thick for
hoses of nominal size less than 500, at least 10 mm thick for hoses of nominal size in the range from 500 to
850 inclusive and at least 12 mm thick for hoses of nominal size in the range from 900 to 1 300 inclusive, and
end fittings as described in 5.3 on both ends. The lining thickness shall be at least 8 mm for nominal sizes up
to and including 200, at least 10 mm for nominal sizes 250 to 500 inclusive, at least 12 mm for nominal sizes
550 to 800 inclusive and at least 16 mm for nominal sizes 850 to 1 300 inclusive.

oSIST prEN ISO 28017:2025
ISO/DIS 28017:2025(en)
5.2 Flotation material
The closed-cell flotation material used in type 1 hose assemblies shall adhere firmly both to the hose body
and to the outer cover so that it cannot move or tend to become detached in service. At the ends of the hose, a
space shall be provided to facilitate the insertion of connection bolts and to allow the use of mechanical tools
for tightening nuts on the bolts. The flotation material shall be distributed over the whole length of the hose
assembly in such a manner that the hose assembly floats evenly when connected to other assemblies in a string.
This does not apply to hose assemblies for special applications (e.g. the end of a string, tapered hose, etc.).
5.3 End fittings and end connections
End fittings shall be mechanically and chemically bonded to the hose body. With hoses intended for delivery
use only, clamped-on and swaged-on nipples are not acceptable, but such nipples may be utilized with hoses
intended for suction use. Alternatively, flanged end connections built up of hose reinforcement, lining and
cover material are acceptable provided they are additionally reinforced by steel stiffening rings to avoid
distortion when the connection bolts are tightened. All hose assemblies shall be fitted with either end
fittings or flanged end connections unless otherwise required by the end user.
6 Dimension and tolerances
6.1 Diameters
The test shall be carried out in accordance with ISO 4671. The inside diameters of hoses shall conform to the
values given in Table 4.
The test shall be carried out in accordance with ISO 4671. The outside diameters of hoses shall conform to
the values specified by the customer.
NOTE For hoses manufactured on mandrels with diameters in inches, the tolerances on the inside diameter
are the same as those given for hoses with diameters in metric units in Table 4 (i.e. ±3 mm for sizes 4 in to 8 in
inclusive, ±4 mm for 10 in to 12 in inclusive, ±5 mm for 14 in to 30 in inclusive, ±6 mm for 32 in to 40 in inclusive
and ±7 mm for 44 in and 48 in).
Table 4 — Diameters of hoses
Actual inside diameter
mm
Nominal size
min. max.
100 97 103
150 147 153
200 197 203
250 246 254
300 296 304
350 345 355
400 395 405
450 445 455
500 495 505
550 545 555
600 595 605
650 645 655
700 695 705
750 745 755
800 794 806
850 844 856
oSIST prEN ISO 28017:2025
ISO/DIS 28017:2025(en)
TTabablele 4 4 ((ccoonnttiinnueuedd))
Actual inside diameter
mm
Nominal size
min. max.
900 894 906
1 000 994 1 006
1 100 1 093 1 107
1 200 1 193 1 207
1 300 1 293 1 307
6.2 Hose assembly length
The hose assembly length shall be determined according to the conditions of use. Unless otherwise agreed
between the customer and the manufacturer, the tolerances on the hose assembly length shall be +2 % and −2 %.
7 Physical properties
7.1 Rubber compounds
7.1.1 Abrasion resistance of lining
7.1.1.1 Test pieces
Test pieces shall be prepared from sheets of lining compound (of cure state equivalent to that of the hose) of
thickness at least 6 mm. The method of preparation shall be as specified in ISO 4649.
7.1.1.2 Abrasion resistance
The test shall be carried out in accordance with ISO 4649:2017, method A. The relative volume loss, ΔV ,
rel
shall not be greater than 200 mm . This test is required each time type testing is carried out and when a
...