Aerospace series - Heat resisting nickel base alloy NiCr20Co3Fe3 - Annealed - Wire - D ≤ 10 mm

EN 2402 specifies the requirements relating to: Heat resisting nickel base alloy NiCr20Co3Fe3 Annealed Wire D ≤ 10 mm for aerospace applications.

Luft- und Raumfahrt - Hochwarmfeste Nickelbasislegierung NiCr20Co3Fe3 - Geglüht - Draht - D ≤ 10 mm

Diese Norm legt die Anforderungen an
Hochwarmfeste Nickelbasislegierung NiCr20Co3Fe3
Geglüht
Draht D ≤ 10 mm
zur Anwendung in der Luft- und Raumfahrt fest.
ANMERKUNG Weitere übliche Bezeichnungen:
Es muss nur die chemische Zusammensetzung dieser Norm beachtet werden.

Série aérospatiale - Alliage résistant à base de nickel NiCr20Co3Fe3 - Requit - Fil - D ≤ 10 mm

Aeronavtika - Toplotnoodporna zlitina na osnovi niklja NiCr20Co3Fe3 - Žarjena - Žica - D ≤ 10 mm

EN 2402 določa zahteve glede: žarjene žice D ≤ 10 mm iz toplotnoodporne zlitine na osnovi niklja NiCr20Co3Fe3 za uporabo v aeronavtiki.

General Information

Status
Published
Publication Date
05-Jun-2014
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
19-May-2014
Due Date
24-Jul-2014
Completion Date
06-Jun-2014

Buy Standard

Standard
EN 2402:2014
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.49.025.15Neželezove zlitine na splošnoNon-ferrous alloys in generalICS:Ta slovenski standard je istoveten z:EN 2402:2014SIST EN 2402:2014en,fr,de01-julij-2014SIST EN 2402:2014SLOVENSKI
STANDARD



SIST EN 2402:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2402
April 2014 ICS 49.025.15 English Version
Aerospace series - Heat resisting nickel base alloy NiCr20Co3Fe3 - Annealed - Wire - D ≤ 10 mm
Série aérospatiale - Alliage résistant à base de nickel NiCr20Co3Fe3 - Requit - Fil - D ≤ 10 mm
Luft- und Raumfahrt - Hochwarmfeste Nickelbasislegierung NiCr20Co3Fe3 - Geglüht - Draht - D ≤ 10 mm This European Standard was approved by CEN on 27 December 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2402:2014 ESIST EN 2402:2014



EN 2402:2014 (E) 2 Contents
Page coreword .3 Introduction .4 1 Scope .5 2 kormative references .5 SIST EN 2402:2014



EN 2402:2014 (E) 3 coreword This document (EN 2402:2014) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2014, and conflicting national standards shall be withdrawn at the latest by October 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.