SIST EN IEC 62841-2-12:2024
(Main)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-12: Particular requirements for hand-held concrete vibrators (IEC 62841-2-12:2024 (EQV)
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 2-12: Particular requirements for hand-held concrete vibrators (IEC 62841-2-12:2024 (EQV)
IEC 62841-2-12:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held concrete vibrators. IEC 62841-1:2014, Clause 1 is applicable, except as follows.
Addition: This document applies to hand-held concrete vibrators.
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen – Sicherheit – Teil 2-12: Besondere Anforderungen für handgeführte Innenrüttler (IEC 62841-2-12:2024)
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 2-12: Exigences particulières pour les vibrateurs à béton portatifs (IEC 62841-2-12:2024)
IEC 62841-2-12:2024 doit être utilisé conjointement avec l'IEC 62841-1:2014. Le présent document complète ou modifie les articles correspondants de l'IEC 62841-1 de façon à la transformer en norme IEC: Exigences particulières pour les vibrateurs à béton portatifs. IEC 62841-1:2014, L’article 1 est applicable, sauf dans les cas suivants.
Addition: Ce document s'applique aux vibrateurs à béton portatifs.
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-12. del: Posebne zahteve za ročne vibratorje betona (IEC 62841-2-12:2024)
Standard IEC 62841-2-12:2024 se uporablja v povezavi s standardom IEC 62841-1:2014. Ta dokument dopolnjuje ali spreminja ustrezne določbe standarda IEC 62841-1, tako da to publikacijo pretvori v standard IEC: Posebne zahteve za ročne vibratorje betona. 1. točka standarda IEC 62841-1:2014 se uporablja, razen kot sledi.
Dodatek: ta dokument se uporablja za ročne vibratorje betona.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-
12. del: Posebne zahteve za ročne vibratorje betona (IEC 62841-2-12:2024)
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 2-12: Particular requirements for hand-held concrete vibrators
(IEC 62841-2-12:2024 (EQV)
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen – Sicherheit – Teil 2-12: Besondere Anforderungen für
handgeführte Innenrüttler (IEC 62841-2-12:2024)
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 2-12: Exigences particulières pour les vibrateurs à béton portatifs (IEC
62841-2-12:2024)
Ta slovenski standard je istoveten z: EN IEC 62841-2-12:2024
ICS:
25.140.20 Električna orodja Electric tools
25.140.30 Orodja za ročno uporabo Hand-operated tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 62841-2-12
NORME EUROPÉENNE
EUROPÄISCHE NORM August 2024
ICS 25.140.20
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-12: Particular
requirements for hand-held concrete vibrators
(IEC 62841-2-12:2024)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-12 : Exigences transportable Werkzeuge und Rasen- und
particulières pour les vibrateurs à béton portatifs. Gartenmaschinen - Sicherheit - Teil 2-12: Besondere
(IEC 62841-2-12:2024) Anforderungen für handgeführte Innenrüttler
(IEC 62841-2-12:2024)
This European Standard was approved by CENELEC on 2024-08-05. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62841-2-12:2024 E
European foreword
The text of document 116/692/FDIS, future edition 1 of IEC 62841-2-12, prepared by IEC/TC 116
"Safety of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 62841-2-12:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-08-05
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2028-08-05
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CENELEC by the
European Commission. The Standing Committee of the EFTA States subsequently approves these
requests for its Member States.
For the relationship with EU Legislation, see informative Annex ZZ, which is an integral part of
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62841-2-12:2024 was approved by CENELEC as a
European Standard without any modification.
IEC 62841-2-12 ®
Edition 1.0 2024-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety –
Part 2-12: Particular requirements for hand-held concrete vibrators
Outils électroportatifs à moteur, outils portables et machines pour jardins et
pelouses – Sécurité –
Partie 2-12 : Exigences particulières pour les vibrateurs à béton portatifs
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.140.20 ISBN 978-2-8322-8138-3
– 2 – IEC 62841-2-12:2024 © IEC 2024
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 6
5 General conditions for the tests . 7
6 Radiation, toxicity and similar hazards . 7
7 Classification . 7
8 Marking and instructions . 7
9 Protection against access to live parts . 7
10 Starting . 8
11 Input and current . 8
12 Heating . 8
13 Resistance to heat and fire . 8
14 Moisture resistance . 9
15 Resistance to rusting . 9
16 Overload protection of transformers and associated circuits . 9
17 Endurance . 9
18 Abnormal operation . 10
19 Mechanical hazards . 10
20 Mechanical strength . 11
21 Construction . 11
22 Internal wiring . 12
23 Components . 12
24 Supply connection and external flexible cords . 12
25 Terminals for external conductors . 12
26 Provision for earthing . 13
27 Screws and connections . 13
28 Creepage distances, clearances and distances through insulation . 13
Annexes . 14
Annex I (informative) Measurement of noise and vibration emissions . 14
Annex K (normative) Battery tools and battery packs . 16
Annex L (normative) Battery tools and battery packs provided with mains connection
or non-isolated sources . 18
Bibliography . 19
Figure 101 – Typical design a) of a concrete vibrator . 6
Figure 102 – Typical design b) of a concrete vibrator . 6
Table 4 – Required performance levels . 10
IEC 62841-2-12:2024 © IEC 2024 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –
Part 2-12: Particular requirements for hand-held concrete vibrators
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.