SIST EN 10209:2013
(Main)Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions
Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions
This European Standard applies to cold rolled non-coated low carton steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. It does not apply to cold rolled narrow strip (rolling width < 600 mm) nor to cold rolled flat products for which there is a specific standard, in particular the following: cold-rolled low carbon steel flat products for cold forming (EN 10130); cold-rolled non oriented electrical steel sheet and strip delivered in fully processed state (prEN 10106); cold-rolled electrical non-alloyed steel sheet and strip delivered in semi-processed state (prEN 10126) ; cold-rolled electrical alloyed steel sheet and strip delivered in semi-processed state (prEN 10165); cold reduced blackplate (EN 10205); steel sheet and strip for welded gas cylinders (prEN 10120 ); hot-rolled flat products made of high yield strength steels for cold forming (prEN 10149); cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (prEN 10139); cold-rolled structural steels for general purposes.
Kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Emaillieren - Technische Lieferbedingungen
Die vorliegende Europäische Norm gilt für kaltgewalzte Flacherzeugnisse ohne Überzug in Breiten 600 mm und Dicken 3 mm aus weichen Stählen zum Kaltumformen, die zum Emaillieren geeignet sind und als Blech, Breitband, längsgeteiltes Breitband oder aus längsgeteiltem Breitband oder Blech hergestellten Stäbe geliefert werden.
Diese Europäische Norm gilt nicht für Kaltband (in Walzbreiten 600 mm), ferner nicht für kaltgewalzte Flacherzeugnisse, für die eigene Normen bestehen, z. B. für folgende Erzeugnisse:
- kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Kaltumformen (EN 10130),
- kaltgewalztes nichtkornorientiertes Elektroblech und -band im schlussgeglühten Zustand (EN 10106),
- kaltgewalztes Elektroblech und -band aus unlegierten Stählen im nicht schlussgeglühten Zustand
(EN 10126),
- kaltgewalztes Elektroblech und -band aus legierten Stählen im nicht schlussgeglühten Zustand
(EN 10165),
- kaltgewalztes Feinstblech (EN 10205),
- Stahlblech und -band für geschweißte Gasflaschen (EN 10120),
- warmgewalzte Flacherzeugnisse aus Stählen mit hoher Streckgrenze zum Kaltumformen (EN 10149),
- Kaltband ohne Überzug in Walzbreiten unter 600 mm aus weichen unlegierten Stählen für Kaltumformung (EN 10139),
- kaltgewalzte allgemeine Baustähle.
Produits plats laminés à froid, en acier doux pour émaillage par vitrification - Conditions techniques de livraison
La présente Norme européenne est applicable aux produits plats laminés à froid, non revêtus, de largeur supérieure ou égale à 600 mm, d’épaisseur inférieur ou égale à 3 mm, en acier doux, pour l’emboutissage ou pliage à froid et destinés à un émaillage par vitrification, livrés en tôles, larges bandes, larges bandes refendues, barres obtenues à partir de larges bandes refendues ou de tôles.
Elle n’est pas applicable aux feuillards (largeur de laminage < 600 mm) laminés à froid ni aux produits plats laminés à froid pour lesquels il existe une norme spécifique, en particulier aux produits suivants :
- Produits plats laminés à froid en acier doux pour emboutissage à froid (EN 10130),
- Tôles magnétiques en acier à grains non orientés laminées à froid et livrées à l’état fini (prEN 10106),
- Tôles magnétiques en acier non alliés, laminées à froid et livrées à l’état semi-fini (prEN 10126),
- Tôles magnétique en acier allié, laminées à froid et livrées à l’état semi-fini (prEN 10165),
- Fer noir laminé à froid (EN 10205),
- Tôles et bandes pour bouteilles à gaz soudées en acier (prEN 10120)
- Produits plats laminés à chaud en aciers à haute limite d’élasticité pour formage à froid (prEN 10149),
- Feuillards non revêtus relaminés à froid en aciers doux non alliés, pour formage à froid (prEN 10139),
- Aciers de construction d’usage général laminés à froid.
Hladno valjani ploščati izdelki iz maloogljičnih jekel za emajliranje - Tehnični dobavni pogoji
Ta evropski standard se uporablja za hladno valjane neprevlečene ploščate izdelke iz maloogljičnih jekel v valjanih širinah, ki so enake ali večje od 600 mm ter debelinah, enakih ali manjših od 3 mm, dobavljene v ploščah, širokih trakovih, rezanih širokih trakovih ali rezanih dolžinah iz rezanih širokih trakov ali plošč. Ne uporablja se za valjani ozki trak (valjana širina < 600 mm) niti za hladno valjane ploščate izdelke, za katere se uporablja posebni standard, zlasti naslednji: hladno valjani ploščati izdelki iz maloogljičnih jekel za hladno preoblikovanje (EN 10130); hladno valjane neusmerjene električne jeklene plošče in trakovi, dobavljeni popolnoma obdelani (prEN 10106); hladno valjane električne nelegirane jeklene plošče in trakovi, dobavljeni delno obdelani (prEN 10126); hladno valjane električne legirane jeklene plošče in trakovi, dobavljeni delno obdelani (prEN 10165); hladno preoblikovane nepocinkane plošče (EN 10205); jeklene plošče in trakovi za varjene plinske cilindre (prEN 10120 ); vroče valjani ploščati izdelki iz jekel z visoko mejo tečenja za hladno preoblikovanje (prEN 10149); hladno valjani neprevlečeni nelegirani ozki trakovi iz mehkega jekla za hladno preoblikovanje (prEN 10139); hladno valjana konstrukcijska jekla za splošne namene.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Emaillieren - Technische LieferbedingungenProduits plats laminés à froid, en acier doux pour émaillage par vitrification - Conditions techniques de livraisonCold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10209:2013SIST EN 10209:2013en,fr,de01-september-2013SIST EN 10209:2013SLOVENSKI
STANDARDSIST EN 10209:19981DGRPHãþD
SIST EN 10209:2013
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10209
June 2013 ICS 77.140.50 Supersedes EN 10209:1996English Version
Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions
Produits plats laminés à froid, en acier doux pour émaillage par vitrification - Conditions techniques de livraison
Kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Emaillieren - Technische Lieferbedingungen This European Standard was approved by CEN on 11 April 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10209:2013: ESIST EN 10209:2013
EN 10209:2013 (E) 2 Contents Page
Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .5 4 Designation .5 5 Requirements .5 6 Tests .8 7 Identification .9 8 Packaging .9 9 Disputes .9 10 Information to be supplied by the purchaser at the time of ordering .9 Annex A (normative)
Methods for determining the resistance to fish scaling of a steel sheet for enamelling . 13 Annex B (normative)
Method for determining mass loss (iron loss) due to pickling for steel grades for direct enamelling in accordance with 5.4.2 . 17 Annex C (normative)
Method for determining the adherence level of enamel applied to a steel sheet . 20 Annex D (informative)
Characteristics for the selection of enamelling steel grades . 25
SIST EN 10209:2013
EN 10209:2013 (E) 3 Foreword This document (EN 10209:2013) has been prepared by Technical Committee ECISS/TC 109 “Flat products for cold working - Qualities, dimensions, tolerances and specific test”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2013, and conflicting national standards shall be withdrawn at the latest by December 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10209:1996. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 10209:2013
EN 10209:2013 (E) 4
1 Scope This European Standard applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. It does not apply to cold rolled narrow strip (rolling width < 600 mm) nor to cold rolled flat products for which there is a specific standard, in particular the following: — cold-rolled low carbon steel flat products for cold forming (EN 10130); — cold-rolled non oriented electrical steel sheet and strip delivered in fully processed state (EN 10106); — cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341); — cold reduced blackplate (EN 10205); — steel sheet and strip for welded gas cylinders (EN 10120); — cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139); — cold-rolled structural steels for general purposes; — cold-rolled flat products made of high yield strength for cold forming (EN 10268). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel products EN 10027-1, Designation systems for steels - Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10049, Measurement of roughness average Ra and peak count RPc on metallic flat products EN 10079:2007, Definition of steel products EN 10131, Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape EN 10204, Metallic products - Types of inspection documents EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377) EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1) ISO 10113, Metallic materials — Sheet and strip — Determination of plastic strain ratio SIST EN 10209:2013
EN 10209:2013 (E) 5 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10079:2007. 4 Designation 4.1 Steel names are attributed in accordance with EN 10027-1; numerical designations are attributed in accordance with EN 10027-2. All steels reported in Table 2 are non alloy and alloy quality steels. 4.2 Products conforming to this European Standard shall be designated, in order, in the following way: a) product designation (e.g. strip, sheet or “slit strip cut longitudinally”); b) number of this European Standard (EN 10209); c) name or numerical designation of the steel, shown in Table 2; d) where appropriate, the symbol relating to surface finish (see Table 1). Examples of conventional designations: Designation of a steel sheet with the symbolic designation DC01EK and the numerical designation 1.0390 with rough surface finish (r): Sheet EN 10209 DC01EK r or Sheet EN 10209 — 1.0390 r Designation of a wide strip of steel with the symbolic designation DC06ED and the numerical designation 1.0872 with normal surface finish (m): Wide strip EN 10209 — DC06ED m or Wide strip EN 10209 — 1.0872 m. 5 Requirements 5.1 Steelmaking and manufacturing processes Unless otherwise agreed at the time of ordering, the production methods shall be left to the discretion of the manufacturer. The purchaser shall be informed of these processes if specified in the purchase order. 5.2 Method of deoxidation See Table 2. 5.3 Chemical composition The maximum values for the chemical compositions based on ladle analysis shall be as given in Table 2. SIST EN 10209:2013
EN 10209:2013 (E) 6 5.4 Suitability for vitreous enamelling 5.4.1 Qualities DCO1EK, DC04EK, DC05EK and DC06EK are suitable for one or two coats of conventional enamelling. 5.4.2 Qualities DC03ED, DC04ED and DC06ED are suitable for direct enamelling, as well as for the two coat – one fire process and for the special applications of two coat enamelling for sag resistance. 5.4.3 The following methods of test are defined in order to determine the suitability of the steel for enamelling: — hydrogen permeation test (see Annex A) (alternatively, if agreed at the time of ordering, an enamelling test as described in A.2 may be specified). NOTE These two tests enable the risk of fish scaling following enamelling to be assessed. — iron loss test for qualities of steel for direct enamelling as described in 5.4.2 (see Annex B). 5.4.4 An enamel adherence test (see Annex C) is also defined (pretreatment and enamelling conditions shall be agreed at the time of ordering). 5.4.5 The application of the methods of test described in Annex A, Annex B and Annex C may be the subject of an agreement at the time of ordering. 5.5 Delivery condition 5.5.1 Products specified in this standard should be supplied in the skin-passed condition. If agreed at the time of ordering non-skin-passed products may be supplied. 5.5.2 The products are normally delivered oiled. In this case, both the surfaces are preserved by a layer of neutral non-drying oil, free of foreign bodies and uniformly spread in such a way that under normal conditions of packaging, transportation, handling and storage the products will show no corrosion for up to three months. If the conditions of transportation or storage are such that special protection against corrosion is required, the purchaser shall inform the manufacturer at the time of the ordering. The layer of oils shall be capable of being removed by alkaline solutions or normal solvents. The choice of protective oils may be the subject of special agreement. If the purchaser does not require the surfaces to be oiled, this shall be clearly indicated at the time of the ordering. NOTE If the order is for unoiled products, the manufacturer is not responsible for the risk of rust. The purchaser is also advised that there is a greater risk of the appearance of light scratches during handling, transportation, and application. 5.6 Choice of properties The products covered by this European Standard shall correspond to the requirements of Table 1 and Table 2.
Subject to agreement between the supplier and the purchaser, they may be supplied with particular suitability for the production of a specific part; in this case a maximum rejection percentage may be set by mutual agreement and acceptance on the basis of mechanical properties would not apply. 5.7 Mechanical properties The mechanical properties given in Table 2 only apply to skin-passed products. These mechanical properties are valid for the period specified in Table 2 from the date on which the products are made available. The date of availability shall be notified to the purchaser with reasonable prior notice compatible with the validity of the mechanical properties. SIST EN 10209:2013
EN 10209:2013 (E) 7 5.8 Surface characteristics 5.8.1 General The surface characteristics consist of the surface appearance and surface finish. 5.8.2 Surface appearance The products are supplied with a surface appearance which does not adversely affect suitability for forming, the application of an enamel coating and the uniform appearance of the enamelled surface on the exposed surface. When supplied as wide strip and slit strip, the percentage of surface defects may be higher than when supplied as sheet and cut lengths. This shall be taken into account by the purchaser and the permissible percentage of surface defects shall be set by special agreement at the time of ordering.
Unless otherwise agreed, a single surface of the product shall comply with the specified requirements. The other surface shall be such that during subsequent treatment it does not have a deleterious effect on the better surface. 5.8.3 Surface finish The surface finish may be normal or rough. In the absence of a requirement in the order, products shall be supplied with the normal surface finish. The limiting figures for average surface roughness for the two types of finish are given in Table 1. The measurements shall be made in accordance with EN 10049. If specially agreed at the time of ordering, other ranges for surfaces are specified for specific end uses. Table 1 — Surface finishes and standard roughness Surface finish Symbol Roughness Normal Rough m r 0,6 µm < Ra ≤ 1,9 µm Ra > 1,6 µm 5.9 Stretcher strain marks All the products are generally subjected to a light skin-pass after annealing at the manufacturer's works to avoid the formation of stretcher strain marks during subsequent forming. The tendency to form such marks may reappear a certain time after the skin-pass. It is therefore in the purchaser's interest to form the products as soon as possible. Quality DC06EK and DC06ED products do not exhibit stretcher strain marks after deformation. For the other qualities the absence of stretcher strain marks may be guaranteed for six months after the products are made available. 5.10 Weldability The material is specified as suitable for normal welding procedures as long as the products are degreased beforehand. The welding procedure shall be specified at the time of ordering (see 10 h). 5.11 Tolerances on dimensions and shape Tolerances on dimensions and shape are given in EN 10131. SIST EN 10209:2013
EN 10209:2013 (E) 8 6 Tests 6.1 General 6.1.1 The purchaser shall specify at the time of ordering his requirements for: — type of inspection and testing: specific or non-specific, see EN 10021; — type of inspection document, see EN 10204. 6.1.2 Specific inspection and testing shall be carried out in accordance with 6.2, 6.3, 6.4, 6.5 and 6.6. 6.1.3 Specific inspection and testing may not be specified either for the product analysis or the surface finish. 6.2 Inspection units The inspection unit is 30 t or a fraction of 30 t products of the same grade and nominal thickness. When a wide coil exceeds 30 t, it constitutes a single inspection unit, as do its products. 6.3 Number of tests For each inspection unit a tensile test shall be carried out, and if required, a determination of r and of the suitability for enamelling shall be performed (see Table 2 and Annex A, Annex B and Annex C). 6.4 Sampling The requirements of EN ISO 377 and EN 10021 are supplemented by the following specific requirements. For sheet and cut lengths the selection of products to be tested and the position of the samples in the products is left to the discretion of the inspection representative. In the case of wide strip and slit wide strip, the sample should preferably be taken from the outer end. If the width of the product permits, the test pieces for the tensile test shall be taken perpendicular to the direction of rolling at a distance of at least 50 mm from the edge of the product. 6.5 Test methods 6.5.1 The products shall be tested in the as-delivered condition. The tests shall be carried out at ambient temperature. 6.5.2 The tensile test shall be carried out as specified in EN ISO 6892-1 using type 2 test pieces (initial gauge length Lo = 80 mm, width b = 20 mm). 6.5.3 Surface roughness shall be measured in accordance with EN 10049. 6.5.4 The determination of the plastic strain ratio r shall be carried out in accordance with ISO 10113. 6.5.5 The tests for suitability for enamelling (see 5.4.3) shall be carried out in accordance with — Annex A for the fish scaling resistance test; — Annex B for the mass loss due to pickling test; — Annex C for the adherence test. SIST EN 10209:2013
EN 10209:2013 (E) 9 6.5.6 For the determination of the chemical composition the corresponding European Standards shall apply in cases of dispute. 6.6 Retests The requirements of EN 10021 shall apply. For coils, in the event of the test results giving rise to dispute, the samples for retests shall be taken at intervals of at least one lap but also at a maximum distance of 20 m from the appropriate end. 6.7 Inspection documents If agreed at the time of ordering, an inspection document chosen from those given in EN 10204 shall be supplied (see also 6.1.1). 7 Identification All materials shall be identified with at least the following information: — the conventional designation as described in Clause 4; — the coil or bundle number; — the supplier's mark. Typically, the identification is applied by either a label or using an easily removable non-corrosive ink on the inspected surface. Other identification requirements shall be agreed at the time of ordering. 8 Packaging The packaging requirements shall be agreed at the time of ordering. 9 Disputes With regard to any claims and actions, EN 10021 shall apply. 10 Information to be supplied by the purchaser at the time of ordering To permit the manufacturer to supply products conforming to this standard, the following information should be given in the order: a) the full designation as given in Clause 4; b) nominal dimensions and quantities; c) if the products are to be supplied non skin-passed, d) if the products are to be delivered with mill edges or sheared edges; e) limits on mass and sizes of coils and individual bundles; f) intended application for the products; g) enamelling process used (see Annex D); SIST EN 10209:2013
EN 10209:2013 (E) 10 h) if the products are to be welded, indication of the method to be used; i) if the products are to be supplied as suitable for making a specific part; j) if inspection documents are requested and type; k) if an external inspection is to be carried out at the manufacturer's works; l) if oiling is not required; m) detailed descript
...
SLOVENSKI STANDARD
oSIST prEN 10209:2010
01-september-2010
+ODGQRYDOMDQLSORãþDWLL]GHONLL]PDORRJOMLþQLKMHNHO]DHPDMOLUDQMH7HKQLþQL
GREDYQLSRJRML
Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery
conditions
Kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Emaillieren - Technische
Lieferbedingungen
Produits plats laminés à froid, en acier doux pour émaillage par vitrification - Conditions
techniques de livraison
Ta slovenski standard je istoveten z: prEN 10209
ICS:
77.140.50 3ORãþDWLMHNOHQLL]GHONLLQ Flat steel products and semi-
SROL]GHONL products
oSIST prEN 10209:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 10209:2010
---------------------- Page: 2 ----------------------
oSIST prEN 10209:2010
EUROPEAN STANDARD
DRAFT
prEN 10209
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2010
ICS 77.140.50 Will supersede EN 10209:1996
English Version
Cold rolled low carbon steel flat products for vitreous enamelling
- Technical delivery conditions
Produits plats laminés à froid, en acier doux pour émaillage Kaltgewalzte Flacherzeugnisse aus weichen Stählen zum
par vitrification - Conditions techniques de livraison Emaillieren - Technische Lieferbedingungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ECISS/TC 109.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10209:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
Contents Page
Foreword .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .6
4 Designation .6
5 Requirements .6
5.1 Steelmaking and manufacturing processes .6
5.2 Method of deoxidation .6
5.3 Chemical composition .6
5.4 Suitability for vitreous enamelling .7
5.5 Delivery condition .7
5.6 Choice of properties .7
5.7 Mechanical properties .7
5.8 Surface characteristics .8
5.8.1 General .8
5.8.2 Surface appearance .8
5.8.3 Surface finish .8
5.9 Stretcher strain marks .8
5.10 Weldability .8
5.11 Tolerances on dimensions and shape .8
6 Tests .9
6.1 General .9
6.2 Inspection units .9
6.3 Number of tests .9
6.4 Sampling .9
6.5 Test methods .9
6.6 Retests . 10
6.7 Inspection documents . 10
7 Identification . 10
8 Packaging . 10
9 Disputes . 10
10 Information to be supplied by the purchaser at the time of ordering . 10
Annex A (normative) Methods for determining the resistance to fish scaling of a steel sheet for
enamelling . 13
A.1 Hydrogen permeation test . 13
A.1.1 Field of application . 13
A.1.2 Principle . 13
A.1.3 Apparatus . 13
A.1.4 Sampling . 13
A.1.5 Preparation . 13
A.1.6 Checks on the degreasing quality . 14
A.1.7 Permeation test procedure . 14
A.1.8 Evaluation . 15
A.2 Fish scaling test using special enamel . 16
Annex B (normative) Method for determining mass loss (iron loss) due to pickling for steel grades for
direct enamelling in accordance with 5.4.2 . 17
B.1 Principle . 17
B.2 Apparatus . 17
B.3 Sampling . 17
2
---------------------- Page: 4 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
B.4 Preparation . 18
B.5 Weighing . 18
B.6 Cleaning . 18
B.7 Checks on degreasing quality . 18
B.8 Pickling . 18
B.9 Drying. 19
B.10 Weighing . 19
B.11 Evaluation . 19
Annex C (normative) Method for determining the adherence level of enamel applied to a steel sheet . 20
C.1 Field of application . 20
C.2 Principle . 20
C.3 Apparatus . 20
C.4 Description of the apparatus . 20
C.5 Procedure . 20
C.6 Adherence level evaluation . 21
C.6.1 Flat pieces . 21
.
C.6.2 Thinner sheet steel < 0,6 mm . 21
C.6.3 Deformed pieces . 21
Annex D (informative) Characteristics for the selection of enamelling steel grades. 24
3
---------------------- Page: 5 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
Foreword
This document (prEN 10209:2010) has been prepared by Technical Committee ECISS/TC 109 “Flat products for
cold working - Qualities, dimensions, tolerances and specific test”, the secretariat of which is held by
AFNOR.
This document will supersede EN 10209:1996
This document is currently submitted to the CEN Enquiry.
4
---------------------- Page: 6 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
1 Scope
This European Standard applies to cold rolled non-coated low carton steel flat products in rolled widths equal to
or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut
lengths obtained from slit wide strip or sheet.
It does not apply to cold rolled narrow strip (rolling width < 600 mm) nor to cold rolled flat products for which
there is a specific standard, in particular the following:
cold-rolled low carbon steel flat products for cold forming (EN 10130);
cold-rolled non oriented electrical steel sheet and strip delivered in fully processed state (prEN 10106);
cold-rolled electrical non-alloyed steel sheet and strip delivered in semi-processed state (prEN 10126) ;
cold-rolled electrical alloyed steel sheet and strip delivered in semi-processed state (prEN 10165);
cold reduced blackplate (EN 10205);
steel sheet and strip for welded gas cylinders (prEN 10120 );
hot-rolled flat products made of high yield strength steels for cold forming (prEN 10149);
cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (prEN 10139);
cold-rolled structural steels for general purposes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 10002-1, Metallic materials -Tensile testing - Part 1: Method of test (at ambient temperature).
EN 10021, General technical delivery requirements for steel and iron products.
EN 10027-1, Designation systems for steels - Part 1: Symbolic designation, main symbols.
EN 10027-2, Designation systems for steels - Part 2: Numerical systems.
EN 10049, Measurement of roughness average Ra and peak count RPc on metallic flat products.
EN 10079, Definition and classification of steel products.
EN 10131, Cold-rolled uncoated low carbon and high yield strength steel flat products for cold forming - Tolerances
on dimensions and shape.
EN 10204, Metallic products - Types of inspection documents.
EN ISO 377, Steel and steel products. Location and preparation of samples and test pieces for mechanical testing.
NF EN ISO 7500-1, Metallic materials - Verification of static uniaxial testing machines - Part 1 :
tension/compression testing machines - Verification and calibration of the force measuring system.
NF EN ISO 9513, Matériaux métalliques - Etalonnage des extensomètres utilisés lors d'essais uniaxiaux.
5
---------------------- Page: 7 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
ISO 10113, Metallic materials - Sheet and strip - Determination of plastic strain ratio
3 Terms and definitions
For the purposes of this European Standard the terms and definitions of the cold rolled flat products are those
given in EN 10079.
4 Designation
4.1 Steel names are attributed in accordance with EN 10027-1; numerical designations are attributed in
accordance with EN 10027-2.
All steels reported in Table 2 are non alloy quality steels.
4.2 Products conforming to this European Standard shall be designated, in order, in the following way:
a) product designation (e.g. strip, sheet or "slit strip cut longitudinally");
b) number of this European Standard (EN 10209);
c) name or numerical designation of the steel, shown in Table 2;
d) where appropriate, the symbol relating to surface finish (see Table 1).
Examples of conventional designations:
Designation of a steel sheet with the symbolic designation DC01EK and the numerical designation 1.0390 with
rough surface finish (r):
Sheet EN 10209 DC01EK r or
Sheet EN 10209 - 1.0390 r
Designation of a wide strip of steel with the symbolic designation DC06ED and the numerical designation 1.0872
with normal surface finish (m):
Wide strip EN 10209 - DC06ED m or
Wide strip EN 10209 - 1.0872 m.
5 Requirements
5.1 Steelmaking and manufacturing processes
Unless otherwise agreed at the time of ordering, the production methods are left to the discretion of the
manufacturer.
The purchaser shall be informed of these processes if he specifies it.
5.2 Method of deoxidation
See Table 2.
5.3 Chemical composition
The maximum values for the chemical compositions based on ladle analysis shall be as given in Table 2.
6
---------------------- Page: 8 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
5.4 Suitability for vitreous enamelling
5.4.1 Qualities DCO1EK, DC04EK, DC05EK and DC06EK are suitable for one or two coats of conventional
enamelling.
5.4.2 Qualities DC03ED, DC04ED and DC06ED are suitable for direct enamelling, as well as for the two coat –
one fire process and for the special applications of two coat enamelling for sag resistance.
5.4.3 The following methods of test are defined in order to determine the suitability of the steel for enamelling:
hydrogen permeation test (see Annex A) (alternatively, if agreed at the time of ordering, an enamelling test as
described in A.2 may be specified).
NOTE These two tests enable the risk of fish scaling following enamelling to be assessed.
iron loss test for qualities of steel for direct enamelling as described in 5.4.2 (see Annex B).
5.4.4 An enamel adherence test (see Annex C) is also defined (pretreatment and enamelling conditions shall be
agreed at the time of ordering).
5.4.5 The application of the methods of test described in Annexes A, B and C may be the subject of an
agreement at the time of ordering.
5.5 Delivery condition
5.5.1 Products specified in this standard are normally supplied in the skin-passed condition. If agreed at the time
of ordering non-skin-passed products may be supplied.
5.5.2 The products are normally delivered oiled. In this case, both the surfaces are preserved by a layer of
neutral non-drying oil, free of foreign bodies and uniformly spread in such a way that under normal conditions of
packaging, transportation, handling and storage the products will show no corrosion for up to three months.
If the conditions of transportation or storage are such that special protection against corrosion is required, the
purchaser shall inform the manufacturer at the time of the ordering.
The layer of oils shall be capable of being removed by alkaline solutions or normal solvents.
The choice of protective oils may be the subject of special agreement.
If the purchaser does not require the surfaces to be oiled, this shall be clearly indicated at the time of the ordering.
NOTE If the order is for unoiled products, the manufacturer is not responsible for the risk of rust. The purchaser is also
advised that there is a greater risk of the appearance of light scratches during handling, transportation, and application.
5.6 Choice of properties
The products covered by this European Standard correspond to the requirements of Tables 1 and 2. Subject to
special agreement, they may be supplied with special suitability for the production of a specific part; in this case a
maximum rejection percentage may be set by mutual agreement and acceptance on the basis of mechanical
properties does not apply.
5.7 Mechanical properties
The mechanical properties given in Table 2 only apply to skin-passed products. These mechanical properties are
valid for the period specified in Table 2 from the date on which the products are made available.
The date of availability shall be notified to the purchaser with reasonable prior notice compatible with the validity of
the mechanical properties.
7
---------------------- Page: 9 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
5.8 Surface characteristics
5.8.1 General
The surface characteristics consist of the surface appearance and surface finish.
5.8.2 Surface appearance
The products are supplied with a surface appearance which does not adversely affect suitability for forming, the
application of an enamel coating and the uniform appearance of the enamelled surface on the exposed surface.
When supplied as wide strip and slit strip, the percentage of surface defects may be higher than when supplied as
sheet and cut lengths. This shall be taken into account by the purchaser and the permissible percentage of surface
defects shall be set by special agreement at the time of ordering. Unless otherwise agreed, a single surface of the
product shall comply with the specified requirements. The other surface shall be such that during subsequent
treatment it does not have a deleterious effect on the better surface.
5.8.3 Surface finish
The surface finish may be normal or rough.
In the absence of a requirement in the order, products shall be supplied with the normal surface finish.
The limiting figures for average surface roughness for the two types of finish are given in Table 1.
The measurements shall be made in accordance with EN 10049.
If specially agreed at the time of ordering, other ranges for surface specified for specific end uses.
Table 1 — Surface finishes and standard roughness
Surface finish Symbol Roughness
Normal m 0,6 µm < R < 1,9 µm
a
Rough r R > 1,6 µm
a
5.9 Stretcher strain marks
All the products are generally subjected to a light skin-pass after annealing at the manufacturer's works to avoid the
formation of stretcher strain marks during subsequent forming. The tendency to form such marks may reappear a
certain after the skin-pass. It is therefore in the purchaser's interest to form the products as soon as possible.
Quality DC06EK and DC06ED products do not exhibit stretcher strain marks after deformation.
For the other qualities the absence of stretcher strain marks may be guaranteed for six months after the products
are made available.
5.10 Weldability
The material is specified as suitable for normal welding procedures as long as the products are degreased
beforehand. The welding procedure shall be specified at the time of ordering (see 10 h).
5.11 Tolerances on dimensions and shape
Tolerances on dimensions and shape are given in EN 10131.
8
---------------------- Page: 10 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
6 Tests
6.1 General
6.1.1 The purchaser shall specify at the time of ordering his requirements for:
type of inspection and testing: specific or non-specific, see EN 10021;
type of inspection document, see EN 10204.
6.1.2 Specific inspection and testing shall be carried out in accordance with 6.2 to 6.6.
6.1.3 Specific inspection and testing may not be specified either for the product analysis or the surface finish.
6.2 Inspection units
The inspection unit is 30 t or a fraction of 30 t products of the same grade and nominal thickness.
When a wide coil exceeds 30 t, it constitutes a single inspection unit, as do its products.
6.3 Number of tests
For each inspection unit a tensile test shall be carried out, and if required, a determination of r and of the suitability
for enamelling (see Table 2 and Annexes A, B, and C).
6.4 Sampling
The requirements of EN ISO 377 and EN 10021 are supplemented by the following specific requirements.
For sheet and cut lengths the selection of products to be tested and the position of the samples in the products is
left to the discretion of the inspection representative.
In the case of wide strip and slit wide strip, the sample should preferably be taken from the outer end.
If the width of the product permits, the test pieces for the tensile test shall be taken perpendicular to the direction of
rolling.
6.5 Test methods
6.5.1 The products shall be tested in the as-delivered condition. The tests shall be carried out at ambient
temperature.
6.5.2 The tensile test shall be carried out as described in EN 10002-1 using type 2 specimens (initial gauge
length L = 80 mm, width b = 20 mm).
o
6.5.3 Surface roughness shall be measured in accordance with EN 10049.
6.5.4 The determination of coefficient r shall be carried out in accordance with ISO 10113.
6.5.5 The tests for suitability for enamelling (see 5.4.3) shall be carried out in accordance with
annex A for the fish scaling resistance test;
annex B for the mass loss due to pickling test;
annex C for the adherence test.
6.5.6 For the determination of the chemical composition the corresponding European Standards shall apply in
cases of dispute.
9
---------------------- Page: 11 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
6.6 Retests
The requirements of EN 10021 shall apply. For coils, in the event of the test results giving rise to dispute, the
samples for retests shall be taken at intervals of at least one lap but also at a maximum distance of 20 m from the
appropriate end.
6.7 Inspection documents
If agreed at the time of ordering, an inspection document chosen from those given in EN 10204 shall be supplied
(see also 6.1.1).
7 Identification
All materials shall be identified with at least the following information:
the conventional designation as described in Clause 4;
the coil or bundle number;
the supplier's mark.
Typically, the identification is applied by either a label or using an easily removable non-corrosive ink on the
inspected surface. Other identification requirements shall be agreed at the time of ordering.
8 Packaging
The packaging requirements shall be agreed at the time of ordering.
9 Disputes
With regard to any claims and actions arising there from, EN 10021 shall apply.
10 Information to be supplied by the purchaser at the time of ordering
To permit the manufacturer to supply products conforming to this standard, the following information should be
given in the order:
a) the full designation as given in clause 4;
b) nominal dimensions and quantities;
c) if the products are to be supplied non skin-passed,
d) if the products are to be delivered with mill edges or sheared edges;
e) limits on mass and sizes of coils and individual bundles;
f) intended application for the products;
g) enamelling process used (see Annex D);
10
---------------------- Page: 12 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
h) if the products are to be welded, indication of the method to be used;
i) if the products are to be supplied as suitable for making a specific part;
j) if inspection documents are requested and type;
k) if an external inspection is to be carried out at the manufacturer's works;
l) if oiling is not required;
m) detailed description of all other special requirements;
n) any special requirements for packaging and marking;
o) the position of the surface of better surface finish quality.
11
---------------------- Page: 13 ----------------------
oSIST prEN 10209:2010
prEN 10209:2010 (E)
a i
Table 2 — Characteristics
_ Chemical composition (ladle analysis) C content
R MPa R A % min r % max
e m 80
Validity of
(product analysis)
max MPa average
Designation in Designation in mechanical
b c l d l
C Ti Mn P S
Method of
accordance with accordance with properties and
l min
deoxidation
% max
EN 10027-1 EN 10027-2 absence of stretcher
strain marks
e l
f f
270 270/390 30 0.08 0.60 0,045 0,050
DC01EK 1.0390 Fully killed 6 months
k
DC04EK 1.0392 Fully killed 6 months 220 270/350 36 0.08 0,50 0,030 0,050
k
DC05EK To be defined !!! Fully killed 6 months 220 270/350 36 1.5 0.08 0,50 0,025 0,050
h
DC06EK 1.0869 Fully killed 6 months 190 270/350 38 1.6 0.02 0.30 0,50 0,020 0,050
j
f f
240 270/370 34
DC03ED 1.0399 Fully killed 6 months 0,40 0,035 0,050 0,004
g j
DC04ED 1.0394 Fully killed 6 months 210 270/350 38 0,40 0,030
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.