Industrial trucks - Safety requirements and verification - Part 2: Self-propelled variable-reach trucks (ISO 3691-2:2023)

This document gives safety requirements and the means for their verification for self-propelled industrial variable-reach trucks and variable-reach container handlers/reach stackers as defined in ISO 5053‑1 (hereafter referred to as trucks), equipped with forks or integral load-handling devices for normal industrial duties (e.g. fork arms or means, such as spreaders, for handling containers).
This document does not apply to:
—    rough-terrain variable-reach trucks,
—    rough-terrain variable-reach trucks for handling containers,
—    lorry mounted trucks covered by ISO 20297-1,
—    machines designed primarily for earth-moving (e.g. loaders and dozers), even when their buckets and blades are replaced with forks,
—    machines from which the load can swing freely in all directions.
This document is not applicable to trucks manufactured before the date of its publication.
For the purposes of this document, fork arms and integrated attachments are considered to be a part of the truck, whereas attachments/equipment/tools mounted on the load carrier or on the fork arms which are removable by the user are not. Nevertheless, for interchangeable equipment, which is assembled with the truck by the operator in order to change the function of, or attribute a new function to, the truck, this document does provide requirements for:
—    the interface with the truck,
—    protection of the operator in the normal operating position from crushing and shearing hazards,
—    operating and maintenance instructions,
—    load charts,
—    marking,
—    provision for transportation, and,
—    indicator lights for attachments for lifting containers
Any regional requirements additional to the provisions of this document are addressed in EN 16307-2:2023 and ISO/TS 3691‑8.
This document deals with all significant hazards, hazardous situations or hazardous events, as listed in Annex B, with the exception of the following, relevant to the applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
It does not establish requirements for hazards that can occur:
—    during construction;
—    when using trucks on public roads;
—    when operating in potentially explosive atmospheres;
—    when lifting persons; or
—    during dismantling, disabling and scrapping.
This document does not provide requirements for:
—    tools, lifting accessories or removeable attachments, which do not change the function or attribute a new function, mounted on the load carrier or fork arms;
—    attachments/equipment mounted on the load carrier or on the fork arms which are removable by the user and which change the function or attribute a new function, except as stated above;
—    the reliability of control systems and performance requirements for safety related parts of control systems; or
—    the requirement for fitting an enclosed cab, whether pressurized or not.

Sicherheit von Flurförderzeugen - Sicherheitsanforderungen und Verifizierung - Teil 2: Motorkraftbetriebene Flurförderzeuge mit veränderlicher Reichweite (ISO 3691-2:2023)

Chariots de manutention - Exigences de sécurité et vérification - Partie 2: Chariots automoteurs à portée variable (ISO 3691-2:2023)

Le présent document définit les exigences de sécurité ainsi que leurs moyens de vérification pour les chariots de manutention automoteurs à portée variable et les chariots porte-conteneur à portée variable/gerbeurs à portée variable tels que définis dans l’ISO 5053‑1 (ci-après désignés chariots), équipés de fourches ou de dispositifs complets de manutention de la charge pour des activités industrielles normales (par exemple, des bras de fourche ou des moyens, tels que des palonniers pour la manutention de conteneurs).
Le présent document ne s’applique pas aux:
—    chariots tout-terrain à portée variable,
—    chariots tout-terrain à portée variable pour la manutention de conteneurs,
—    chariots embarqués sur porteurs routiers couvert par l’ISO 20297‑1,
—    machines conçues principalement pour le terrassement (par exemple, les chargeuses et les bouteurs) même si leurs godets et leurs lames sont remplacés par des fourches,
—    machines dont la charge peut osciller librement dans toutes les directions.
Le présent document n'est pas applicable aux chariots fabriqués avant la date de sa publication.
Pour les besoins du présent document, les bras de fourche et les accessoires intégrés sont considérées comme une partie du chariot, tandis que les accessoires/équipement/outils montés sur le tablier porte-charge ou sur les bras de fourche qui sont démontables par l'utilisateur, ne le sont pas. Toutefois, pour les équipements interchangeables, qui sont assemblés avec le chariot par l'opérateur afin de modifier la fonction ou d'attribuer une nouvelle fonction au chariot, le présent document fournit des exigences pour:
—    l'interface avec le chariot,
—    la protection de l'opérateur en position normale de conduite contre les phénomènes dangereux d'écrasement et de cisaillement,
—    les instructions d'utilisation et de maintenance,
—    les abaques de charge,
—    le marquage,
—    les dispositions pour le transport, et,
—    les voyants lumineux pour les accessoires pour le levage des conteneurs.
Toutes les exigences régionales supplémentaires aux dispositions du présent document, sont traitées dans l’EN 16307‑2:2023 et dans l'ISO/TS 3691‑8.
Le présent document traite de tous les phénomènes dangereux, des situations dangereuses ou des événements dangereux, tels que listés dans l'Annexe B, à l'exception des suivants, relatifs aux machines concernées lorsqu'elles sont utilisées comme prévu et dans des conditions de mauvaise utilisation qui sont raisonnablement prévisibles par le fabricant.
Il n’établit pas d’exigences concernant les phénomènes dangereux qui peuvent apparaître:
—    en cours de fabrication;
—    lorsque les chariots sont utilisés sur des voies publiques;
—    lors d’utilisation en atmosphères potentiellement explosives;
—    lors du levage de personnes; ou
—    lors du démontage, de la mise hors service et de la mise au rebut.
Le présent document ne fournit pas d'exigences pour:
—    les outils, équipements de levage ou accessoires amovibles, qui ne changent pas la fonction ou n'attribuent pas une nouvelle fonction, montés sur le tablier porte-charge ou les bras de fourche;
—    les accessoires/équipements montés sur le tablier porte-charge ou sur les bras de fourche qui sont amovibles par l'utilisateur et qui changent la fonction ou attribuent une nouvelle fonction, sauf comme indiqué ci-dessus;
—    la fiabilité des systèmes de commande et les exigences de performance pour les parties des systèmes de commande liées à la sécu

Vozila za talni transport - Varnostne zahteve in preverjanje - 2. del: Vozila z lastnim pogonom s spremenljivim dosegom (ISO 3691-2:2023)

Ta dokument določa varnostne zahteve in načine za njihovo preverjanje za samognane industrijske tovorne zabojnike in kontejnerske enote za upravljanje/zlagalnike s spremenljivim dosegom, kot so opredeljeni v standardu ISO 5053-1 (nadaljevanju: vozila), opremljenih z napravami za ravnanje s tovorom za običajne industrijske naloge, npr. z vilicami ali napravami, kot so dvigalniki, za prenos zabojnikov).
Ta dokument se ne uporablja za:
– terenska vozila s spremenljivim dosegom,
– terenska vozila s spremenljivim dosegom za prenos zabojnikov,
– vozila z dvigalom in spremenljivim dosegom, zajeta v standard ISO 20297-1,
– stroji, ki so primarno zasnovani za zemeljska dela (npr. nakladalniki in buldožerji), tudi če so njihove žlice in rezila zamenjani z vilicami,
– stroji, na katerih lahko tovor prosto niha v vse smeri.
Ta dokument se ne uporablja za vozila, izdelana pred datumom njegove objave.
V tem dokumentu se vilice in vgrajeni priključki štejejo za del vozila, medtem ko se priključki/oprema/orodja, nameščena na nosilec bremena ali na vilice, ki jih uporabnik lahko sname, ne štejejo za del vozila. Vseeno pa za zamenljivo opremo, ki jo na vozilo namesti upravljavec, da bi spremenil funkcionalnost vozila ali mu dodal novo funkcionalnost, v tem dokumentu niso navedene zahteve za:
– vmesnik z vozilom,
– zaščito upravljavca v normalnem položaju za upravljanje pred nevarnostjo stiskanja ali ureznin,
– navodila za upravljanje in vzdrževanje,
– diagrame obremenitve,
– označevanje,
– pogoje za prevoz in
– svetlobne indikatorje za priključke za dviganje zabojnikov.
Vse regionalne zahteve, poleg zahtev, navedenih v tem dokumentu, so obravnavane v standardih EN 16307-2:2023 in ISO/TS 3691-8.
Ta dokument opisuje vse večje nevarnosti, nevarne situacije in nevarne dogodke, kot je navedeno v dodatku B, z izjemo spodaj navedenih, v zvezi z ustreznimi stroji, kadar se ti uporabljajo v skladu s svojim namenom in pod pogoji nepravilne uporabe, ki jih je razumno predvidel proizvajalec.
Ne določa zahtev za tveganja, do katerih lahko pride:
– med gradnjo;
– pri uporabi vozil na javnih cestah;
– pri upravljanju vozil v potencialno eksplozivnih atmosferah;
– pri dvigovanju oseb; ali
– pri razstavljanju, onemogočanju in razrezovanju.
Ta dokument ne navaja zahtev za:
– orodja, dvižne pripomočke ali snemljive priključke, ki pri namestitvi na nosilec bremena ali vilice ne spremenijo svoje funkcije oziroma ne zagotavljajo nove funkcije;
– priključke/opremo, nameščeno na nosilec bremena ali na vilice, ki jih lahko odstrani uporabnik in ki spremenijo funkcijo ali zagotavljajo novo funkcijo, razen kot je navedeno zgoraj;
– zanesljivost krmilnih sistemov in zahteve glede učinkovitosti z varnostjo povezanih delov krmilnih sistemov; ali
– zahteve za namestitev zaprte kabine pod tlakom ali ne.

General Information

Status
Published
Public Enquiry End Date
22-Dec-2021
Publication Date
03-Apr-2023
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
06-Mar-2023
Due Date
11-May-2023
Completion Date
04-Apr-2023

Relations

Buy Standard

Standard
EN ISO 3691-2:2023
English language
55 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 3691-2:2021
English language
54 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3691-2:2023
01-maj-2023
Nadomešča:
SIST EN ISO 3691-2:2016
SIST EN ISO 3691-2:2016/AC:2016
Vozila za talni transport - Varnostne zahteve in preverjanje - 2. del: Vozila z lastnim
pogonom s spremenljivim dosegom (ISO 3691-2:2023)
Industrial trucks - Safety requirements and verification - Part 2: Self-propelled variable-
reach trucks (ISO 3691-2:2023)
Sicherheit von Flurförderzeugen - Sicherheitsanforderungen und Verifizierung - Teil 2:
Motorkraftbetriebene Flurförderzeuge mit veränderlicher Reichweite (ISO 3691-2:2023)
Chariots de manutention - Exigences de sécurité et vérification - Partie 2: Chariots
automoteurs à portée variable (ISO 3691-2:2023)
Ta slovenski standard je istoveten z: EN ISO 3691-2:2023
ICS:
53.060 Industrijski tovornjaki Industrial trucks
SIST EN ISO 3691-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3691-2:2023

---------------------- Page: 2 ----------------------
SIST EN ISO 3691-2:2023


EN ISO 3691-2
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2023
EUROPÄISCHE NORM
ICS 53.060 Supersedes EN ISO 3691-2:2016
English Version

Industrial trucks - Safety requirements and verification -
Part 2: Self-propelled variable-reach trucks (ISO 3691-
2:2023)
Chariots de manutention - Exigences de sécurité et Sicherheit von Flurförderzeugen -
vérification - Partie 2: Chariots automoteurs à portée Sicherheitsanforderungen und Verifizierung - Teil 2:
variable (ISO 3691-2:2023) Motorkraftbetriebene Flurförderzeuge mit
veränderlicher Reichweite (ISO 3691-2:2023)
This European Standard was approved by CEN on 9 January 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3691-2:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 3691-2:2023
EN ISO 3691-2:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 3691-2:2023
EN ISO 3691-2:2023 (E)
European foreword
This document (EN ISO 3691-2:2023) has been prepared by Technical Committee ISO/TC 110
"Industrial trucks" in collaboration with Technical Committee CEN/TC 150 “Industrial Trucks - Safety”
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2023, and conflicting national standards
shall be withdrawn at the latest by September 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3691-2:2016.
This document is intended to be used with EN 16307-2:2023.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 3691-2:2023 has been approved by CEN as EN ISO 3691-2:2023 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 3691-2:2023

---------------------- Page: 6 ----------------------
SIST EN ISO 3691-2:2023
INTERNATIONAL ISO
STANDARD 3691-2
Second edition
2023-03
Industrial trucks — Safety
requirements and verification —
Part 2:
Self-propelled variable-reach trucks
Chariots de manutention — Exigences de sécurité et vérification —
Partie 2: Chariots automoteurs à portée variable
Reference number
ISO 3691-2:2023(E)
© ISO 2023

---------------------- Page: 7 ----------------------
SIST EN ISO 3691-2:2023
ISO 3691-2:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 3691-2:2023
ISO 3691-2:2023(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 3
4 Safety requirements and/or protective measures . 5
4.1 General . 5
4.1.1 Overall requirements . 5
4.1.2 Normal climatic conditions . 5
4.1.3 Normal operating conditions . 6
4.1.4 Sharp edges . 6
4.1.5 Electrical requirements . 6
4.1.6 Stored energy components. 6
4.2 Starting/moving . 6
4.2.1 Unauthorized starting . 6
4.2.2 Unintended movement and inadvertent activation . 6
4.3 Brakes . 7
4.3.1 General . 7
4.3.2 Failure of energy supply . 7
4.4 Manual control actuator. 7
4.4.1 General . 7
4.4.2 Travel and braking controls . 8
4.4.3 Steering controls . 9
4.4.4 Load-handling controls . 9
4.4.5 Other controls . 9
4.4.6 Marking . . . 10
4.5 Power systems and accessories . . 10
4.5.1 Exhaust system . 10
4.5.2 Cooling system . 10
4.5.3 Fuel tanks . 10
4.5.4 Access to engine and other compartments . 10
4.5.5 Liquefied petroleum gas (LPG)-powered trucks . 11
4.6 Systems for telescoping, lifting and tilting . 13
4.6.1 Lift chains .13
4.6.2 Hydraulic lifting, telescoping and carriage tilting . 14
4.6.3 Hydraulic systems . 14
4.6.4 Fork arms . 15
4.6.5 Fork-arm extensions . 15
4.6.6 Fork carriers.15
4.6.7 Load-handling attachments . 15
4.7 Operator positions . 16
4.7.1 Dimensions . 16
4.7.2 Operator's seat . 16
4.7.3 Operator restraint . 17
4.7.4 Operator access and egress . 17
4.7.5 Protection from road wheels and objects thrown up by the wheels . 17
4.7.6 Protection from burning . 17
4.7.7 Protection against crushing, shearing and trapping . 18
4.8 Stability . 18
4.8.1 General . 18
4.8.2 Specific operating conditions . 18
4.8.3 Longitudinal stability determination . 19
4.9 Protective devices . 19
iii
© ISO 2023 – All rights reserved

---------------------- Page: 9 ----------------------
SIST EN ISO 3691-2:2023
ISO 3691-2:2023(E)
4.9.1 Overhead guard . 19
4.9.2 Load backrest extension . 19
4.9.3 Roll-over protective structures (ROPSs) . 19
4.9.4 Warning device . 19
4.9.5 Starter battery requirements . 20
4.10 Visibility and lighting . 20
4.10.1 Visibility . 20
4.10.2 Lighting . 20
4.11 Operator's cab . 20
4.11.1 General .20
4.11.2 Doors and windows . 20
4.11.3 Fire resistance . 21
4.11.4 Ventilation . 21
4.11.5 Heating, air conditioning and ventilation system. 21
4.11.6 Demisting and defrosting . 22
4.11.7 Pressurization system .22
4.11.8 Wipers and washers . 22
4.11.9 Access and an emergency exit . 23
4.11.10 Storage of instruction handbook . 23
4.11.11 Additional operator's position . 23
4.12 Provisions for transportation of the truck and removable attachments .23
4.13 Environmental requirements. 23
4.13.1 Noise emissions .23
4.13.2 Vibration .23
4.13.3 Electromagnetic compatibility (EMC) . 24
4.14 Devices for towing . 24
5 Verification of safety requirements and/or protective measures .24
5.1 General . 24
5.2 Structural verification . 24
5.2.1 Test loads . . 24
5.2.2 Static test . 25
5.2.3 Dynamic test . 25
5.3 Functional verification . 25
6 Information for use .26
6.1 General . 26
6.2 Instruction handbook.26
6.2.1 Truck . 26
6.2.2 Operation of truck .26
6.2.3 Details for battery-powered trucks . 27
6.2.4 Details for internal-combustion-engine-powered trucks .28
6.2.5 Service and maintenance .28
6.2.6 Transportation, commissioning and storage .28
6.2.7 Truck modification .29
6.3 Marking .29
6.3.1 Information plates .29
6.3.2 Load chart. 30
6.3.3 Information plate for trucks operating in special conditions . 32
6.3.4 Other information .33
6.3.5 Languages . 33
6.3.6 Operator restraint . 33
Annex A (informative) Rated capacity of truck .34
Annex B (informative) List of significant hazards .37
Annex C (normative) Verification of essential health and safety requirements .42
Bibliography .46
iv
  © ISO 2023 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 3691-2:2023
ISO 3691-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 110, Industrial trucks, Subcommittee SC 2,
Safety of powered industrial trucks, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 150, Industrial trucks - Safety, in accordance with the Agreement
on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 3691-2:2016), which has been technically
revised.
The main changes are as follows:
— exclusions and limitations in the Scope have been clarified;
— references for European regional requirements have been updated;
— requirements defining the normal operator position necessary in order for the controls to function
have been added;
— operator weight has been updated;
— information relating to truck modification has been updated;
— verification methods have been added as a new Annex C.
A list of all parts in the ISO 3691 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
© ISO 2023 – All rights reserved

---------------------- Page: 11 ----------------------
SIST EN ISO 3691-2:2023
ISO 3691-2:2023(E)
Introduction
This document is a type-C standard as stated in ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the
market players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organisations, market surveillance etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeh
...

SLOVENSKI STANDARD
oSIST prEN ISO 3691-2:2021
01-december-2021
Vozila za talni transport - Varnostne zahteve in preverjanje - 2. del: Vozila z lastnim
pogonom s spremenljivim dosegom (ISO/DIS 3691-2:2021)
Industrial trucks - Safety requirements and verification - Part 2: Self-propelled variable-
reach trucks (ISO/DIS 3691-2:2021)
Sicherheit von Flurförderzeugen - Sicherheitsanforderungen und Verifizierung - Teil 2:
Motorkraftbetriebene Flurförderzeuge mit veränderlicher Reichweite (ISO/DIS 3691-
2:2021)
Chariots de manutention - Exigences de sécurité et vérification - Partie 2: Chariots
automoteurs à portée variable (ISO/DIS 3691-2:2021)
Ta slovenski standard je istoveten z: prEN ISO 3691-2
ICS:
53.060 Industrijski tovornjaki Industrial trucks
oSIST prEN ISO 3691-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 3691-2:2021

---------------------- Page: 2 ----------------------
oSIST prEN ISO 3691-2:2021
DRAFT INTERNATIONAL STANDARD
ISO/DIS 3691-2
ISO/TC 110/SC 2 Secretariat: SIS
Voting begins on: Voting terminates on:
2021-10-22 2022-01-14
Industrial trucks — Safety requirements and
verification —
Part 2:
Self-propelled variable-reach trucks
Chariots de manutention — Exigences de sécurité et vérification —
Partie 2: Chariots automoteurs à portée variable
ICS: 53.060
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 3691-2:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021

---------------------- Page: 3 ----------------------
oSIST prEN ISO 3691-2:2021
ISO/DIS 3691-2:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 3691-2:2021
ISO/DIS 3691-2:2021(E)

Contents  Page
Foreword .vi
European foreword .vii
Introduction .viii
1  Scope . 1
2  Normative references . 2
3  Terms and definitions . 3
4  Safety requirements and/or protective measures . 5
4.1 General . 5
4.1.1 Overall requirements . 5
4.1.2 Normal climatic conditions. 5
4.1.3 Normal operating conditions . 6
4.1.4 Sharp edges . 6
4.1.5 Electrical requirements . 6
4.1.6 Stored energy components . 6
4.2 Starting/moving. 6
4.2.1 Unauthorized starting . 6
4.2.2 Unintended movement and inadvertent activation . 6
4.3 Brakes . 7
4.3.1 General. 7
4.3.2 Failure of energy supply . 7
4.4 Manual control actuator. 7
4.4.1 General. 7
4.4.2 Travel and braking controls . 8
4.4.3 Steering controls . 9
4.4.4 Load-handling controls . 9
4.4.5 Other controls . 9
4.4.6 Marking .10
4.5 Power systems and accessories.10
4.5.1 Exhaust system .10
4.5.2 Cooling system .10
4.5.3 Fuel tanks .10
4.5.4 Access to engine and other compartments .10
4.5.5 Liquefied petroleum gas (LPG)-powered trucks .11
4.6 Systems for telescoping, lifting and tilting .13
4.6.1 Lift chains .13
4.6.2 Hydraulic lifting, telescoping and carriage tilting .14
4.6.3 Hydraulic systems .14
4.6.4 Fork arms .15
4.6.5 Fork-arm extensions .15
4.6.6 Fork carriers .15
4.6.7 Load-handling attachments .15
4.7 Operator positions .16
4.7.1 Dimensions .16
4.7.2 Operator's seat.16
4.7.3 Operator restraint .16
4.7.4 Operator access and egress .17
4.7.5 Protection from road wheels and objects thrown up by the wheels .17
4.7.6 Protection from burning .17
4.7.7 Protection against crushing, shearing and trapping .17
4.8 Stability .18
4.8.1 General.18
4.8.2 Specific operating conditions .18
© ISO 2021 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 3691-2:2021
ISO/DIS 3691-2:2021(E)

4.8.3 Longitudinal stability determination .18
4.9 Protective devices .19
4.9.1 Overhead guard.19
4.9.2 Load backrest extension .19
4.9.3 Roll-over protective structures .19
4.9.4 Warning device .19
4.9.5 Starter battery requirements .19
4.10 Visibility and lighting .20
4.10.1 Visibility.20
4.10.2 Lighting .20
4.11 Operator's cab .20
4.11.1 General.20
4.11.2 Doors and windows . .20
4.11.3 Fire resistance .21
4.11.4 Ventilation .21
4.11.5 Heating, air conditioning and ventilation system .21
4.11.6 Demisting and defrosting .22
4.11.7 Pressurization system .22
4.11.8 Wipers and washers .22
4.11.9 Access and an emergency exit .22
4.11.10 Storage of instruction handbook .22
4.11.11 Additional operator's position .22
4.12 Provisions for transportation of the truck and removable attachments .22
4.13 Environmental requirements .23
4.13.1 Noise emissions .23
4.13.2 Vibration .23
4.13.3 Electromagnetic compatibility (EMC) .23
4.14 Devices for towing.23
5  Verification of safety requirements and/or protective measures .23
5.1 General .23
5.2 Structural verification .23
5.2.1 Test loads .23
5.2.2 Static test .24
5.2.3 Dynamic test .24
5.3 Functional verification .25
6  Information for use .25
6.1 General .25
6.2 Instruction handbook .25
6.2.1 Truck .25
6.2.2 Operation of truck.25
6.2.3 Details for battery powered trucks .26
6.2.4 Details for internal-combustion-engine powered trucks .27
6.2.5 Service and maintenance .27
6.2.6 Transportation, commissioning and storage .27
6.2.7 Truck modification .28
6.3 Marking .28
6.3.1 Information plates .28
6.3.2 Load chart .29
6.3.3 Information plate for trucks operating in special conditions .31
6.3.4 Other information .32
6.3.5 Languages .32
6.3.6 Operator restraint .32
Annex A (informative) Rated capacity of truck .33
Annex B (informative) List of significant hazards.36
Annex C (normative) Verification of essential health and safety requirements .42
iv © ISO 2021 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 3691-2:2021
ISO/DIS 3691-2:2021(E)

Bibliography .46
© ISO 2021 – All rights reserved v

---------------------- Page: 7 ----------------------
oSIST prEN ISO 3691-2:2021
ISO/DIS 3691-2:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO's adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 110, Industrial trucks, Subcommittee SC 2,
Safety of powered industrial trucks.
A list of all parts in the ISO 3691 series can be found on the ISO website.
vi © ISO 2021 – All rights reserved

---------------------- Page: 8 ----------------------
oSIST prEN ISO 3691-2:2021
ISO/DIS 3691-2:2021(E)

European foreword
This document (EN ISO 3691-2:202X) has been prepared by Technical Committee ISO/TC 110 “Industrial
trucks” in collaboration with Technical CEN/TC 150 “Industrial Trucks - Safety” the secretariat of which
is held by BSI.
This document is currently submitted to the CEN Enquiry.Attention is drawn to the possibility that
some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall
not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3691-2:2016 and is intended to be used in conjunction with EN 16307-
2:20XX with which it forms a package to ensure aligned DOW.According to the CEN-CENELEC Internal
Regulations, the national standards organizations of the following countries are bound to implement
this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia,
Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
© ISO 2021 – All rights reserved vii

---------------------- Page: 9 ----------------------
oSIST prEN ISO 3691-2:2021
ISO/DIS 3691-2:2021(E)

Introduction
General
This document is a type-C standard as stated in ISO 12100.
The machines concerned and the extent to which hazards, hazardous situations or hazardous events
are covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or B
standards, the requirements of this type-C standard take precedence over the requirements of the
other standards for machines that have been designed and built according to the requirements of this
type-C standard.
The ISO 3691 series of standards covers safety requirements and their verification for industrial trucks
as defined in ISO 5053-1.
This part of ISO 3691 does not repeat all the technical rules which are state-of-the art and which are
applicable to the material used to construct the industrial truck. Reference will also need to be made to
ISO 12100.
Structure
An important step forward in the work on the ISO 3691 series of standards was the agreement to issue
a new structure of International Standards for industrial trucks having on one side basic standards for
all kinds of trucks (see Foreword) and on the other side independent standards to cover the respective
specific functions of industrial trucks, e.g. visibility, noise, vibration, electrical requirements, etc.
Legislative situation/Vienna Agreement
From the very beginning, the task of the working group was to revise ISO 3691:1980 and establish
worldwide basic standards to comply with the major legislative regulations in, for example, the EU,
Japan, Australia and North America.
Every effort was made to develop a globally relevant International Standard. That goal was achieved
with most of the issues. For several potential problem areas compromises were needed and will be
needed in the future. Where divergent regional requirements remain, these are addressed by EN 16307-
2:20XX and ISO/TS 3691-8.
In order to ensure that the revised International Standard will be actively used in the ISO member
countries, worldwide, procedures will be necessary to replace the existing national standards and
technical regulations by the revised International Standard. In the European Community, ISO and the
European Committee for Standardization (CEN) agreed on technical co-operation under the Vienna
Agreement, with the aim of replacing European Standards (EN) by International Standards. Other
countries are asked to make similar agreements to ensure that their national standards and technical
regulations are replaced by this International Standard.
Only by these actions will there be the guarantee that products in accordance with International
Standards can be shipped worldwide freely without any technical barriers.
viii © ISO 2021 – All rights reserved

---------------------- Page: 10 ----------------------
oSIST prEN ISO 3691-2:2021
DRAFT INTERNATIONAL STANDARD ISO/DIS 3691-2:2021(E)
Industrial trucks — Safety requirements and
verification —
Part 2:
Self-propelled variable-reach trucks
1  Scope
This part of ISO 3691 gives safety requirements and the means for their verification for self-propelled
industrial variable-reach trucks and variable-reach container handlers/reach stackers as defined in
ISO 5053-1 (hereafter referred to as trucks), equipped with forks or integral load-handling devices for
normal industrial duties (e.g. fork arms o
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.