SIST EN ISO 6507-1:2018
(Main)Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2018)
Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2018)
This document specifies the Vickers hardness test method for the three different ranges of test force for
metallic materials including hardmetals and other cemented carbides (see Table 1).
The Vickers hardness test is specified in this document for lengths of indentation diagonals between
0,020 mm and 1,400 mm. Using this method to determine Vickers hardness from smaller indentations
is outside the scope of this document as results would suffer from large uncertainties due to the
limitations of optical measurement and imperfections in tip geometry.
A periodic verification method is specified for routine checking of the testing machine in service by
the user.
For specific materials and/or products, particular International Standards exist.
Metallische Werkstoffe - Härteprüfung nach Vickers - Teil 1: Prüfverfahren (ISO 6507-1:2018)
Dieses Dokument legt das Verfahren für die Härteprüfung nach Vickers für metallische Werkstoffe, einschließlich Hartmetallen und anderen Sintercarbiden, für drei unterschiedliche Bereiche der Prüfkraft fest (siehe Tabelle 1).
Tabelle 1 — Bereiche der Prüfkraft
Bereiche der Prüfkraft F
N Härtesymbol Benennung
F ≥ 49,03 ≥ HV 5 Härteprüfung nach Vickers
1,961 ≤ F < 49,03 HV 0,2 bis < HV 5 Härteprüfung nach Vickers im Kleinkraftbereich
0,009 807 ≤ F < 1,961 HV 0,001 bis < HV 0,2 Vickers-Mikrohärteprüfung
Die Härteprüfung nach Vickers ist in diesem Dokument für Eindruckdiagonalen mit Längen zwischen 0,020 mm und 1,400 mm festgelegt. Die Anwendung dieses Verfahrens zur Bestimmung der Vickers-Härte (en: Vickers hardness, HV) anhand kleinerer Eindrücke fällt nicht in den Anwendungsbereich dieses Dokuments, da die Ergebnisse aufgrund der Grenzen der optischen Messung und Unregelmäßigkeiten bei der Spitzengeometrie großen Messunsicherheiten unterliegen würden.
Für die Routineüberprüfung der vom Anwender genutzten Prüfmaschine ist ein Verfahren zur regelmäßigen Überprüfung festgelegt.
Für besondere Werkstoffe und/oder Erzeugnisse gibt es spezielle Internationale Normen.
Matériaux métalliques - Essai de dureté Vickers - Partie 1: Méthode d'essai (ISO 6507-1:2018)
L'ISO 6507-1:2018 spécifie la méthode d'essai de dureté Vickers pour les trois plages différentes de force d'essai, pour les matériaux métalliques y compris les métaux durs et autres carbures cimentaires.
Kovinski materiali - Preskus trdote po Vickersu - 1. del: Preskusni postopek (ISO 6507-1:2018)
Ta dokument določa metodo za preskus trdote po Vickersu za tri različne razpone preskusne sile za kovinske materiale, vključno s trdinami in drugimi cementiranimi karbidi (glejte preglednico 1).
Preskus trdote po Vickersu je v tem dokumentu določen za dolžine diagonal zarez od 0,020 do 1,400 mm. Uporaba te metode za določanje trdote po Vickersu na podlagi manjših zarez ne sodi v področje uporabe tega dokumenta, saj bi bili rezultati nezanesljivi zaradi negotovosti, povezane z omejitvami optičnega merjenja in nepravilnostmi geometrije konice.
Določena je tudi metoda za redno preverjanje pri rutinskem pregledovanju naprave za preskušanje, ki jo uporablja uporabnik.
Za posebne materiale in/ali izdelke obstajajo posamezni mednarodni standardi.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6507-1:2018
01-julij-2018
1DGRPHãþD
SIST EN ISO 6507-1:2006
Kovinski materiali - Preskus trdote po Vickersu - 1. del: Preskusni postopek (ISO
6507-1:2018)
Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2018)
Metallische Werkstoffe - Härteprüfung nach Vickers - Teil 1: Prüfverfahren (ISO 6507-
1:2018)
Matériaux métalliques - Essai de dureté Vickers - Partie 1: Méthode d'essai (ISO 6507-
1:2018)
Ta slovenski standard je istoveten z: EN ISO 6507-1:2018
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 6507-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6507-1:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 6507-1:2018
EN ISO 6507-1
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2018
EUROPÄISCHE NORM
ICS 77.040.10 Supersedes EN ISO 6507-1:2005
English Version
Metallic materials - Vickers hardness test - Part 1: Test
method (ISO 6507-1:2018)
Matériaux métalliques - Essai de dureté Vickers - Partie Metallische Werkstoffe - Härteprüfung nach Vickers -
1: Méthode d'essai (ISO 6507-1:2018) Teil 1: Prüfverfahren (ISO 6507-1:2018)
This European Standard was approved by CEN on 18 January 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6507-1:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6507-1:2018
EN ISO 6507-1:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 6507-1:2018
EN ISO 6507-1:2018 (E)
European foreword
This document (EN ISO 6507-1:2018) has been prepared by Technical Committee ISO/TC 164
“Mechanical testing of metals” in collaboration with Technical Committee ECISS/TC 101 “Test methods
for steel (other than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2018, and conflicting national standards
shall be withdrawn at the latest by September 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6507-1:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6507-1:2018 has been approved by CEN as EN ISO 6507-1:2018 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 6507-1:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 6507-1:2018
INTERNATIONAL ISO
STANDARD 6507-1
Fourth edition
2018-01
Metallic materials — Vickers
hardness test —
Part 1:
Test method
Matériaux métalliques — Es
...
SLOVENSKI STANDARD
oSIST prEN ISO 6507-1:2016
01-oktober-2016
Kovinski materiali - Preskus trdote po Vickersu - 1. del: Preskusni postopek
(ISO/DIS 6507-1:2016)
Metallic materials - Vickers hardness test - Part 1: Test method (ISO/DIS 6507-1:2016)
Metallische Werkstoffe - Härteprüfung nach Vickers - Teil 1: Prüfverfahren (ISO/DIS
6507-1:2016)
Matériaux métalliques - Essai de dureté Vickers - Partie 1: Méthode d'essai (ISO/DIS
6507-1:2016)
Ta slovenski standard je istoveten z: prEN ISO 6507-1
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
oSIST prEN ISO 6507-1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 6507-1:2016
---------------------- Page: 2 ----------------------
oSIST prEN ISO 6507-1:2016
DRAFT INTERNATIONAL STANDARD
ISO/DIS 6507-1
ISO/TC 164/SC 3 Secretariat: DIN
Voting begins on: Voting terminates on:
2016-07-12 2016-10-03
Metallic materials — Vickers hardness test —
Part 1:
Test method
Matériaux métalliques — Essai de dureté Vickers —
Partie 1: Méthode d’essai
ICS: 77.040.10
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 6507-1:2016(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2016
---------------------- Page: 3 ----------------------
oSIST prEN ISO 6507-1:2016
ISO/DIS 6507-1:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 6507-1:2016
ISO/DIS 6507-1:2016(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references .1
3 Principle .1
4 Symbols, abbreviated terms, and designations .2
4.1 Symbols and abbreviated terms used in this document .2
4.2 Designation of hardness number .3
5 Testing machine .3
5.1 Testing machine .3
5.2 Indenter .3
5.3 Diagonal measuring system.4
6 Test piece .4
6.1 Test surface.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.