Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system

This part of EN 1451 specifies the requirements for solid-wall polypropylene (PP) pipes, fittings and the system intended for:
-   soil and waste discharge applications (low and high temperature) inside buildings (application area code "B");
-   soil and waste discharge applications (low and high temperature) for both inside buildings and buried in the ground within the building structure (application area code "BD").
This part of EN 1451 is also applicable to PP pipes and fittings and the system intended for the following purposes:
-   ventilating part of the pipework in association with discharge applications;
-   rainwater pipework within the building structure.
It also specifies the test parameters for the test methods referred to in this standard.
This standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
It applies to pipes and fittings, marked with "B", which are intended to be used inside buildings and outside buildings fixed onto the wall.
This standard is applicable to PP pipes and fittings of the following types:
-   plain-ended;
-   with integral elastomeric ring seal socket;
-   for butt fusion joints.
whereby the fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.

Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem

Dieser Teil von EN 1451 legt für Vollwand-Rohrleitungssysteme aus Polypropylen (PP) Anforderungen an Rohre, Formstücke und das Rohrleitungssystem für Abwasserleitungen fest, die in Schwerkraft-entwässerungsanlagen zum Ableiten von Abwasser (niedriger und hoher Temperatur) eingesetzt werden:
- innerhalb von Gebäuden (Anwendungskennzeichen "B");
- innerhalb von Gebäuden und erdverlegt innerhalb der Gebäudestruktur (Anwendungskenn-zeichen "BD").
Der vorgesehene Verwendungszweck wird durch die Kennzeichnung der Erzeugnisse mit "B" oder "BD" angezeigt.
ANMERKUNG 1 Für erdverlegte Anwendungen innerhalb der Gebäudestruktur sind nur Rohrleitungsteile mit der Kennzeichnung "BD" mit Maßen ≥ 75 mm und einer Nenn-Ringsteifigkeit von mindestens SN 4 bestimmt.
Dieser Teil von EN 1451 gilt ebenfalls für Rohre, Formstücke und das Rohrleitungssystem aus PP für die folgenden Verwendungszwecke:
- Lüftungsleitungen in Verbindung mit Abwasseranwendungen;
- Regenfallleitungen innerhalb der Gebäudestruktur.
Er legt auch die Prüfparameter für die Prüfverfahren fest, auf die in dieser Norm verwiesen wird.
Diese Europäische Norm behandelt eine Reihe von Nennweiten, mehrere Rohr- und Formstückreihen sowie Empfehlungen für die Einfärbung.
ANMERKUNG 2 Die geeignete Auswahl aus diesen Aspekten unter Berücksichtigung der jeweils geltenden Anforde-rungen sowie aller maßgebenden nationalen Bestimmungen und Verlegeverfahren oder -vorschriften, z. B. CEN/TR 13801 [1], liegt in der Verantwortung des Kunden oder Auftraggebers.
ANMERKUNG 3 Rohre, Formstücke und andere Rohrleitungsteile, die einer der in Anhang B aufgeführten Normen zu Kunststofferzeugnissen entsprechen, können mit Rohren und Formstücken nach der vorliegenden Europäischen Norm verwendet werden, sofern sie die Anforderungen an die Maße von Verbindungen nach Abschnitt 6 und die Anforderungen nach Tabelle 18 erfüllen.
Diese Norm gilt für mit B" gekennzeichnete Rohre und Formstücke, die für die Verwendung innerhalb von Gebäuden und außerhalb, an Gebäuden befestigt, vorgesehen sind.
Sie gilt für mit "BD" gekennzeichnete Rohre und Formstücke, die für die Verwendung sowohl innerhalb von Gebäuden als auch erdverlegt innerhalb der Gebäudestruktur vorgesehen sind.
Diese Norm gilt für Rohre und Formstücke aus PP der folgenden Typen:
- mit glatten Enden;
- mit angeformter Steckmuffe mit elastomeren Dichtringen;
- für Stumpfschweißverbindungen,
wobei Formstücke durch Spritzgießen oder aus Rohren und/oder aus Teilen, die durch Spritzgießen hergestellt wurden, gefertigt werden können.
ANMERKUNG 4 EN 476 [2] legt die allgemeinen Anforderungen an Rohrleitungsteile fest, die in Abwasserrohren, in Abwasserleitungen und -kanälen für Schwerkraftentwässerungssysteme verwendet werden. Rohre und Formstücke, die dieser Norm entsprechen, erfüllen diese Anforderungen vollständig.
ANMERKUNG 5 Informationen zur chemischen Beständigkeit von PP enthält ISO/TR 10358 [3] und Informationen zu Werkstoffen auf Kautschukbasis enthält ISO/TR 7620 [4].

Systèmes de canalisations en plastiques pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments — Polypropylène (PP) — Partie 1: Spécifications pour tubes, raccords et le système

La présente Norme européenne spécifie les exigences pour les tubes et raccords à paroi compacte en polypropylène (PP) et le système destinés à être utilisés pour :
-   les applications d’évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l’intérieur des bâtiments (code de zone d’application « B ») ;
-    les applications d'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) utilisables aussi bien à l'intérieur des bâtiments qu'en enterré dans la structure du bâtiment (code de zone d’application « BD ».
NOTE 1   L’utilisation prévue est repérée au niveau du marquage des produits par « B » ou « BD ».
NOTE 2   Seuls sont destinés à l'usage en enterré dans la structure du bâtiment, les composants marqués « BD ».
La présente Norme européenne est également applicable aux tubes et raccords en PP et le système destinés aux usages suivants :
-   la partie de ventilation du réseau de canalisation en association avec des applications d’évacuation des eaux-usées ;
-   les canalisations pour les eaux pluviales à l'intérieur de la structure du bâtiment.
Elle spécifie également les paramètres d'essai pour les méthodes d'essai référencées dans la présente norme.
La présente Norme européenne couvre une gamme de dimensions nominales, une gamme de séries de tubes et de raccords et donne des recommandations concernant les couleurs.
NOTE 3   Il est de la responsabilité de l'acheteur ou du prescripteur d'effectuer les sélections appropriées à partir de ces données en tenant compte des exigences particulières et des éventuelles règles nationales et des pratiques ou codes pour la pose appropriés, par exemple, le CEN/TR 13801[1].
NOTE 4   Les tubes, les raccords et autres composants conformes à l'une des normes de produits plastiques listées dans l'Annexe C peuvent être utilisés avec des tubes et des raccords conformes à la présente Norme européenne dans la mesure où ils répondent aux exigences pour les dimensions d'assemblage données dans l'Article 6 et aux exigences du Tableau 18.
Cette norme s'applique aux tubes et aux raccords marqués «B» destinés à être utilisés à l'intérieur des bâtiments et fixés sur les murs à l'extérieur des bâtiments.
La présente Norme européenne s'applique aux tubes et aux raccords en PP des types suivants :
-   à extrémité lisse ;
-   avec emboîture intégrée avec bague d'étanchéité en élastomère ;
-   pour assemblage par soudage bout-à-bout ;
où les raccords peuvent être fabriqués par moulage par injection ou être façonnés à partir de tubes et/ou de pièce moulées.

Cevni sistemi iz polimernih materialov za nizko- in visokotemperaturne odvodne sisteme v zgradbah - Polipropilen (PP) - 1. del: Specifikacije za cevi, fitinge in sistem

Ta del standarda EN 1451 določa zahteve za polipropilenske (PP) cevi in fitinge v trdnih stenah ter sisteme za: – (nizko- in visokotemperaturne) odvodne sisteme v zgradbah (koda območja uporabe »B«); – (nizko- in visokotemperaturne) odvodne sisteme v zgradbah in sisteme, vkopane v zemljo znotraj stavbne konstrukcije (koda območja uporabe »BD«. Ta del standarda EN 1451 se uporablja tudi za polipropilenske cevi in fitinge ter sistem za: – prezračevalne dele sistema cevi, povezanega z odvodnim sistemom; – sistem cevi za deževnico v zgradbi. Določa tudi preskusne parametre za preskusne metode, navedene v tem standardu. Ta standard zajema širok nabor nazivnih velikosti ter serij cevi in fitingov ter podaja priporočila glede barve. Uporablja se za cevi in fitinge, označene z oznako »B«, ki se namestijo v notranje ali zunanje stene zgradbe. Ta standard se uporablja za naslednje vrste polipropilenskih cevi in fitingov: – z ravnim zaključkom; – s celovitimi elastomernimi tesnilnimi obroči; – za soležno taljene spoje, pri čemer so fitingi izdelani z vbrizgavanjem oziroma iz cevi in/ali oblikovancev.

General Information

Status
Published
Public Enquiry End Date
29-Mar-2016
Publication Date
13-Dec-2017
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
08-Dec-2017
Due Date
12-Feb-2018
Completion Date
14-Dec-2017

Relations

Buy Standard

Standard
EN 1451-1:2018
English language
51 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za nizko- in visokotemperaturne odvodne sisteme v zgradbah - Polipropilen (PP) - 1. del: Specifikacije za cevi, fitinge in sistemKunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Polypropylen (PP) - Teil 1: Anforderungen an Rohre, Formstücke und das RohrleitungssystemSystèmes de canalisations en plastiques pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments — Polypropylène (PP) — Partie 1: Spécifications pour tubes, raccords et le systèmePlastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system91.140.80Drenažni sistemiDrainage systems23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:EN 1451-1:2017SIST EN 1451-1:2018en,fr,de01-januar-2018SIST EN 1451-1:2018SLOVENSKI
STANDARDSIST EN 1451-1:19991DGRPHãþD



SIST EN 1451-1:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1451-1
November
t r s y ICS
t uä r v rä r sâ
{ sä s v rä z r Supersedes EN
s v w sæ sã s { { zEnglish Version
fittings and the system Systèmes de canalisations en plastiques pour
sã Spécifications pour tubesá raccords et le système
KunststoffæRohrleitungssysteme zum Ableiten von Anforderungen an Rohreá Formstücke und das Rohrleitungssystem This European Standard was approved by CEN on
s z September
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v w sæ sã t r s y ESIST EN 1451-1:2018



EN 1451-1:2017 (E) 2 Contents Page
European foreword . 4 1 Scope . 5 2 Normative references . 6 3 Terms and definitions . 7 4 Symbols and abbreviations . 10 4.1 Symbols . 10 4.2 Abbreviations . 10 5 Material . 11 5.1 PP-compound . 11 5.2 Additional requirement for pipe and fitting material for application area BD . 11 5.3 Utilization of non-virgin material . 12 5.4 Melt mass-flow rate . 12 5.5 Thermal stability (OIT) . 12 5.6 Sealing ring retaining means . 12 5.7 Fire behaviour . 12 6 General characteristics . 13 6.1 Appearance . 13 6.2 Colour . 13 7 Geometrical characteristics . 13 7.1 General . 13 7.2 Dimensions of pipes . 13 7.2.1 Outside diameters . 13 7.2.2 Effective length of pipes . 14 7.2.3 Chamfering . 15 7.2.4 Wall thickness . 15 7.3 Dimensions of fittings . 17 7.3.1 Outside diameters . 17 7.3.2 Design lengths . 17 7.3.3 Wall thickness . 17 7.4 Dimensions of sockets and pipe ends . 18 7.4.1 Dimensions of ring seal sockets and spigot ends . 18 7.4.2 Dimensions of pipe ends for butt fusion joints . 22 7.5 Types of fittings . 22 8 Mechanical characteristics . 39 8.1 Mechanical characteristics of pipes. 39 8.1.1 General characteristics . 39 8.1.2 Additional characteristics for pipes . 40 8.2 Mechanical characteristics of fittings for application area BD . 41 9 Physical characteristics . 42 9.1 Physical characteristics of pipes. 42 9.2 Physical characteristics of fittings . 43 10 Performance requirements . 44 11 Sealing rings . 45 SIST EN 1451-1:2018



EN 1451-1:2017 (E) 3 12 Marking . 45 12.1 General . 45 12.2 Minimum required marking of pipes . 45 12.3 Minimum required marking of fittings . 46 12.4 Additional marking . 47 Annex A (normative)
Utilization of non-virgin PP material . 48 A.1 Own reprocessed material from pipes and fittings . 48 A.2 External reprocessed and recycled materials with an agreed specification . 48 A.2.1 Material from PP pipes and fittings . 48 A.2.2 Material from PP products other than pipes and fittings . 49 Annex B (informative)
Product standards . 50 Bibliography . 51
SIST EN 1451-1:2018



EN 1451-1:2017 (E) 4 European foreword This document (EN 1451-1:2017) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be withdrawn at the latest by May 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1451-1:1998. EN 1451, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) consists of the following parts: — Part 1: Specifications for pipes, fittings and the system — Part 2: Guidance for the assessment of conformity (CEN/TS) The main changes with respect to the previous edition are: — updating in accordance with the new template; — updating of normative references; — thermal stability (OIT) requirement is made valid in general; — two new dimensions for nominal size and outside diameter have been added, 250 mm and 315 mm; — alignment of the impact resistance requirements for BD applications with the UD applications in
EN 1852-1; — utilization of non-virgin PP materials are described in the new Annex A; — Annex B has been deleted and the relevant text has been moved to the main standard; — new Annex B “Product
standards” has been added. System standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Organization for Standardization (ISO). They are supported by separate standards on test methods to which references are made throughout the system standard. The system standards are consistent with general standards on functional requirements and on recommended practice for installation. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 1451-1:2018



EN 1451-1:2017 (E) 5 1 Scope This part of EN 1451 specifies the requirements for solid-wall polypropylene (PP) pipes, fittings and the system intended for: — soil and waste discharge applications (low and high temperature) inside buildings (application area code “B”); — soil and waste discharge applications (low and high temperature) for both inside buildings and buried in the ground within the building structure (application area code “BD”). The intended use is reflected in the marking of products by “B” or “BD.
NOTE 1 For use buried in the ground within the building structure are intended only those components marked with “BD”, with dimensions equal to or greater than 75 mm and nominal ring stiffness of at least SN4. This part of EN 1451 is also applicable to PP pipes and fittings and the system intended for the following purposes: — ventilating part of the pipework in association with discharge applications; — rainwater pipework within the building structure. It also specifies the test parameters for the test methods referred to in this standard. This European Standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes, e.g. CEN/TR 13801 [1]. NOTE 3 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 18. This standard applies to pipes and fittings, marked with “B”, which are intended to be used inside buildings and outside buildings fixed onto the wall. It applies to pipes and fittings, marked with “BD”, which are intended to be used for both inside buildings and buried in the ground within the building structure. This standard is applicable to PP pipes and fittings of the following types: — plain-ended, — with integral elastomeric ring seal socket, — for butt fusion joints, whereby the fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 4 EN 476 [2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements. NOTE 5 For information about the chemical resistance of PP, guidance is given in ISO/TR 10358 [3] and for rubber materials in ISO/TR 7620[4]. SIST EN 1451-1:2018



EN 1451-1:2017 (E) 6 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber EN 681-2, Elastomeric Seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers EN 12099, Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content EN ISO 472, Plastics - Vocabulary (ISO 472) EN ISO 580, Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580) EN ISO 1043-1, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1) EN ISO 1133-1, Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1) EN ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1) EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2) EN ISO 1183-2, Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2) EN ISO 2505, Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505) EN ISO 3126, Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126) EN ISO 3451-1, Plastics - Determination of ash - Part 1: General methods (ISO 3451-1) EN ISO 11357-6, Plastics - Differential scanning calorimetry (DSC) - Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (ISO 11357-6) EN ISO 9969, Thermoplastics pipes - Determination of ring stiffness (ISO 9969) prEN ISO 13254, Thermoplastics piping systems for non-pressure applications - Test method for watertightness (ISO 13254) prEN ISO 13255, Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for airtightness of joints (ISO 13255) prEN ISO 13257, Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257) SIST EN 1451-1:2018



EN 1451-1:2017 (E) 7 prEN ISO 13259, Thermoplastics piping systems for underground non-pressure applications - Test method for leaktightness of elastomeric sealing ring type joints (ISO 13259) prEN ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics fittings - Test method for impact strength (ISO 13263) prEN ISO 13264, Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings (ISO 13264) EN ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method ISO 4065, Thermoplastics pipes - Universal wall thickness table EN ISO 11173, Thermoplastics pipes — Determination of resistance to external blows — Staircase method 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 472, EN ISO 1043-1 and the following apply. 3.1 application area code code used in the marking of pipes and fittings to indicate the application area(s) for which they are intended, as follows: — B: application area code for components intended for use above ground inside the building, or for components outside buildings fixed onto the wall; — D: application code for the area under and within 1 m from the building where the pipes and fittings are buried in ground and are connected to the underground drainage and sewerage system; — BD: application area code for components intended for use for both code B and code D application areas Note 1 to entry: In D application areas, the existence of external forces from the surroundings in addition to the hot water discharge is usual. Note 2 to entry: Other application area codes U and UD not covered by this standard are defined elsewhere, e.g. in EN 1852-1. 3.2 nominal size 3.2.1 nominal size DN numerical designation of the size of a component, other than a component designated by thread size, which is approximately equal to the manufacturing dimension, in millimetres 3.2.2 nominal size DN/OD nominal size, related to the outside diameter SIST EN 1451-1:2018



EN 1451-1:2017 (E) 8 3.3 nominal outside diameter dn specified outside diameter, in millimetres, assigned to a nominal size DN/OD 3.4 outside diameter de value of the measurement of the outside diameter through its cross section at any point of a pipe or spigot of a fitting, rounded to the next greater 0,1 mm 3.5 mean outside diameter dem value of the measurement of the outer circumference of a pipe or spigot of a fitting in any cross section,
3,142), rounded to the next greater 0,1 mm 3.6 inside diameter ds value of the measurement of the inside diameter through its cross section at any point of a socket, rounded to the next greater 0,1 mm 3.7 mean inside diameter of a socket dsm arithmetical mean of a number of measurements of the inside diameter of a socket in the same cross section 3.8 wall thickness e value of measurement of the wall thickness at any point around the circumference of a component 3.9 mean wall thickness em arithmetical mean of a number of measurements of the wall thickness, regularly spaced around the circumference and in the same cross section of a component, including the measured minimum and the measured maximum values of the wall thickness in that cross section 3.10 pipe series S dimensionless number for pipe designation (see ISO 4065) 3.11 standard dimension ratio SDR nominal ratio of the outside diameter, dn, to the minimum wall thickness, emin SIST EN 1451-1:2018



EN 1451-1:2017 (E) 9 3.12 nominal ring stiffness SN numerical designation of the ring stiffness of a pipe or fitting which is a convenient round number relative to the determined stiffness in kilonewtons per square metre (kN/m2), indicating the minimum ring stiffness of a pipe or fitting 3.13 fabricated fitting fitting produced from pipe and/or from injection-moulded fittings by thermoforming or welding 3.14 solid wall pipe and fitting pipe or fitting with smooth internal and external surface with the same compound/formulation through the wall 3.15 material definitions
3.15.1 copolymer polymer derived from more than one species of monomer 3.15.2 homopolymer polymer derived from one species of monomer 3.15.3 virgin material material in the form such as granules or powder that has not been subjected to use or processing other than that required for its manufacture and to which no reprocessed or recycled material has been added Note 1 to entry: It is understood that the addition of additives such as stabilizers and pigments is still resulting into a virgin material. 3.15.4 own reprocessed material material prepared from rejected unused pipes, gutters or fittings and ancillaries, including trimmings from the production of pipes or fittings, that has been reprocessed in a manufacturer's plant after having been previously processed by the same manufacturer by a process such as moulding or extrusion, and for which the complete formulation is known 3.15.5 external reprocessed material material prepared from unused thermoplastics products regardless of where those products were manufactured 3.15.6 recycled material material from used thermoplastic products which have been cleaned and crushed or ground SIST EN 1451-1:2018



EN 1451-1:2017 (E) 10 3.15.7 reformulated material recycled/reprocessed material that has been reformulated, by additives and processing techniques, to meet an agreed specification 3.15.8 agreed specification specification of the relevant material characteristics agreed between the supplier of the non-virgin material and the pipe, fitting and/or ancillary manufacturer 4 Symbols and abbreviations 4.1 Symbols A length of engagement B length of lead-in C depth of sealing zone e2 wall thickness of a socket e3 wall thickness in the groove area l effective length of a pipe L1 length of spigot R radius of swept fittings Z design length of a fitting
nominal angle of a fitting 4.2 Abbreviations MFR melt mass-flow rate OIT oxidation induction time PP-B polypropylene copolymer PP-H polypropylene homopolymer TIR true impact rate SIST EN 1451-1:2018



EN 1451-1:2017 (E) 11 5 Material 5.1 PP-compound The compound for pipes and fittings shall be PP-base material (homopolymer or copolymer) to which are added those additives that are needed to facilitate the manufacture of components conforming to the requirements of this standard. 5.2 Additional requirement for pipe and fitting material for application area BD The material of pipes and fittings intended to be used in application area BD shall comply with the additional requirements given in Table 1, when tested in accordance with the methods and the parameters indicated in Table 1. The pipe and fitting material shall be tested in form of a pipe. Table 1 — Material characteristics of pipes and fittings intended for BD applications Characteristic Requirements Material type and test designation Test parameters Test method Resistance to internal pressure No failure during the test period PP-H: Test at 140 h at 80 °C End caps Test temperature Orientation Number of test pieces Circumferential (hoop) stress
Conditioning period Type of test Test period Types A or B
80 °C
Free 3
6,0 MPa 1 h Water-in-water 140 h EN ISO 1167-1 and EN ISO 1167-2 PP-H: Test at 1 000 h
at 95 °C End caps Test temperature Orientation Number of test pieces Circumferential (hoop) stress
Conditioning period Type of test Test period Types A or B
95 °C
Free 3
3,5 MPa 1 h Water-in-water 1 000 h PP- B: Test at 140 h at 80 °C End caps Test temperature Orientation Number of test pieces Circumferential (hoop) stress
Conditioning period Type of test Test period Types A or B
80 °C
Free 3
4,2 MPa 1 h Water-in-water 140 h SIST EN 1451-1:2018



EN 1451-1:2017 (E) 12 Characteristic Requirements Material type and test designation Test parameters Test method PP- B: Test at 1 000 h at 95 °C End caps Test temperature Orientation Number of test pieces Circumferential (hoop) stress
Conditioning period Type of test Test period Types A or B
95 °C
Free 3
2,5 MPa 1 h Water-in-water 1 000 h 5.3 Utilization of non-virgin material For the utilization of non-virgin PP materials, conditions and requirements are given in Annex A. 5.4 Melt mass-flow rate The MFR of the base material shall be tested in accordance with EN ISO 1133-1 using the test parameters: temperature 230 °C and loading mass 2,16 kg. Pipes and fittings shall be made from materials with an MFR
¶ 3,0 g/10 min. Materials for pipes and fittings for butt fusion joints shall be designated by the following classes with regard to the MFR: Class A:
MFR

0,3 g/10 min Class B: 0,3 g/10 min <
MFR

0,6 g/10 min Class C: 0,6 g/10 min <
MFR

0,9 g/10 min Class D: 0,9 g/10 min <
MFR

1,5 g/10 min Only pipes and fittings made from materials of the same or adjacent MFR-classes may be fused together. 5.5 Thermal stability (OIT) The test shall be carried out in accordance with EN ISO 11357-6 using a test temperature of 200 °C. The oxidation induction time of the material shall not be less than 8 min. 5.6 Sealing ring retaining means Sealing rings may be retained using means made from polymers other than PP. 5.7 Fire behaviour Pipes and fittings conforming to this standard shall conform to any relevant national requirements on fire regulations. SIST EN 1451-1:2018



EN 1451-1:2017 (E) 13 6 General characteristics 6.1 Appearance When viewed without magnification the following requirements apply: — the internal and external surfaces of pipes and fittings shall be smooth, clean and free from grooving, blistering, impurities, pores or other surface irregularity likely to prevent performance of pipes and fittings with this standard; — each end of a pipe or a fitting shall be cleanly cut, if applicable, and shall be square to its axis. 6.2 Colour The pipes and fittings shall be coloured through the wall. The colours of pipes and fittings should be preferably grey, black or white. Other colours may be used. 7 Geometrical characteristics 7.1 General Dimensions shall be measured in accordance with EN ISO 3126. NOTE The figures given in this standard are only schematic sketches intended to indicate the relevant dimensions. They do not necessarily represent the manufactured componen
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.