SIST EN ISO 4016:2002

Hexagon head bolts - Product grade C (ISO 4016:1999)

Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months because //FV has been missed (Res BT C 243/1999) (CC/991125)

Sechskantschrauben mit Schaft - Produktklasse C (ISO 4016:1999)

Diese Internationale Norm legt Eigenschaften von Sechskantschrauben mit Schaft, mit Gewinden von M5 bis M64 und Produktklasse C fest. Falls in besonderen Fällen andere Festlegungen als die in dieser Norm aufgeführten in dieser Norm benötigt werden, sollten diese den entsprechenden ISO-Normen entnommen werden, z.B. ISO 724, ISO 888, ISO 898-1, ISO 965-1 und ISO 4759-1.

Vis a tete hexagonale partiellement filetées - Grade C (ISO 4016:1999)

La présente Norme internationale spécifie les caractéristiques des vis à tête hexagonale partiellement filetées de filetage M5 à M64 inclus, de grade C. Si, dans des cas particuliers, des spécifications autres que celles figurant dans la présente Norme internationale sont requises, il est recommandé de les prendre dans les Normes internationales existantes, par exemple ISO 724, ISO 888, ISO 898-1, ISO 965-1 et ISO 4759-1.

Vijaki s šestrobo glavo - Razred izdelave C (ISO 4016:1999)

General Information

• Status: Withdrawn
• Publication Date: 30-Jun-2002
• Withdrawal Date: 31-May-2011
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 31-May-2011
• Due Date: 23-Jun-2011
• Completion Date: 01-Jun-2011
• Ref Project: EN ISO 4016:2000 - Hexagon head bolts - Product grade C (ISO 4016:1999)

Relations

• Replaced By: SIST EN ISO 4016:2011 - Hexagon head bolts - Product grade C (ISO 4016:2011)
• Effective Date: 01-Jul-2011
• Replaces: SIST EN 24016:1996 - Hexagon head bolts - Product grade C (ISO 4016:1988)
• Effective Date: 01-Jul-2002

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 4016:2002
01-julij-2002
1DGRPHãþD
SIST EN 24016:1996
Vijaki s šestrobo glavo - Razred izdelave C (ISO 4016:1999)
Hexagon head bolts - Product grade C (ISO 4016:1999)
Sechskantschrauben mit Schaft - Produktklasse C (ISO 4016:1999)
Vis a tete hexagonale partiellement filetées - Grade C (ISO 4016:1999)
Ta slovenski standard je istoveten z: EN ISO 4016:2000
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 4016:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 4016:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 4016:2002

---------------------- Page: 3 ----------------------

SIST EN ISO 4016:2002

---------------------- Page: 4 ----------------------

SIST EN ISO 4016:2002

---------------------- Page: 5 ----------------------

SIST EN ISO 4016:2002

---------------------- Page: 6 ----------------------

SIST EN ISO 4016:2002
INTERNATIONAL ISO
STANDARD 4016
Third edition
1999-08-15
Hexagon head bolts — Product grade C
Vis à tête hexagonale partiellement filetées — Grade C
A
Reference number
ISO 4016:1999(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 4016:2002
ISO 4016:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 4016 was prepared by Technical Committee ISO/TC 2, Fasteners.
This third edition cancels and replaces the second edition (ISO 4016:1988) which has been technically revised.
©  ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 4016:2002
© ISO
ISO 4016:1999(E)
Introduction
This International Standard is part of the complete ISO product standard series on external hexagon drive
fasteners. The series comprises:
a) hexagon head bolts (ISO 4014 to ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032 to ISO 4036, ISO 8673 to ISO 8675);
d) hexagon bolts with flange (ISO 4162 and ISO 15071);
e) hexagon nuts with flange (ISO 4161 and ISO 10663);
f) structural bolts and nuts (ISO 4775, ISO 7411 to ISO 7414 and ISO 7417).
iii

---------------------- Page: 9 ----------------------

SIST EN ISO 4016:2002

---------------------- Page: 10 ----------------------

SIST EN ISO 4016:2002
INTERNATIONAL STANDARD  © ISO ISO 4016:1999(E)
Hexagon head bolts — Product grade C
Scope
1
This International Standard specifies the characteristics of hexagon head bolts with threads from M5 up to and
including M64 of product grade C.
If, in special cases, specifications other than those listed in this International Standard are required, they should
be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1 and
ISO 4759-1.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 225:1983,
Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions.
ISO 724:1993, ISO general-purpose metric screw threads — Basic dimensions.
ISO 888:1976, Bolts, screws and studs — Nominal lengths, and thread lengths for general purpose bolts.
ISO 898-1:1999, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws
and studs.
ISO 965-1:1998, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data.
1)
ISO 3269:— , Fasteners — Acceptance inspection.
ISO 4018:1999, Hexagon head screws — Product grade C.
ISO 4042:1999, Fasteners — Electroplated coatings.
2
)
ISO 4759-1:— ,
Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C.
ISO 8992:1986, Fasteners — General requirements for bolts, screws, studs and nuts.
3)
ISO 10683:— , Fasteners — Non-electrolytically applied zinc flake coatings.

1)
To be published. (Revision of ISO 3269:1988)
2)
To be published. (Revision of ISO 4759-1:1978)
3)
To be published.
1

---------------------- Page: 11 ----------------------

SIST EN ISO 4016:2002
© ISO
ISO 4016:1999(E)
3 Dimensions
See Figure 1 and Tables 1 and 2.
Symbols and designations of dimensions are defined in ISO 225.
Dimensions in millimetres
a
b = 15° to 30°
b
End without special requirements
c
Incomplete thread u < 2 P
d
Reference datum for d
w
e
Washer face permissible
Figure 1
2

---------------------- Page: 12 ----------------------

SIST EN ISO 4016:2002
© ISO
ISO 4016:1999(E)
Table 1 — Preferred threads
Dimensions in millimetres
Thread (d) M5 M6 M8 M10 M12 M16 M20
a
0,8 1 1,25 1,5 1,75 2 2,5
P
b
16 18 22 26 30 38 46
c
b ref. 22 24 28 32 36 44 52
d
35 37 41 45 49 57 65
c max. 0,5 0,5 0,6 0,6 0,6 0,8 0,8
d max. 6 7,2 10,2 12,2 14,7 18,7 24,4
a
d max. 5,48 6,48 8,58 10,58 12,7 16,7 20,84
s
min. 4,52 5,52 7,42 9,42 11,3 15,3 19,16
min. 6,74 8,74 11,47 14,47 16,47 22 27,7
d
w
e min. 8,63 10,89 14,2 17,59 19,85 26,17 32,95
nom. 3,5 4 5,3 6,4 7,5 10 12,5
k max. 3,875 4,375 5,675 6,85 7,95 10,75 13,4
min. 3,125 3,625 4,925 5,95 7,05 9,25 11,6
e
min. 2,19 2,54 3,45 4,17 4,94 6,48 8,12
k
w
r min. 0,2 0,25 0,4 0,4 0,6 0,6 0,8
s nom. = max. 8,00 10,00 13,00 16,00 18,00 24,00 30,00
min. 7,64 9,64 12,57 15,57 17,57 23,16 29,16
f g
l l and l
s g
l l l l l l l l l l l l l l
s g s g s g s g s g s g s g
nom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.
 25 23,95 26,05 5 9
 30 28,95 31,05 10 14 7 12 For sizes above the solid, boldface stepped line, ISO 4018
 35 33,75 36,25 15 19 12 17 is recommended
 40 38,75 41,25 20 24 17 22 11,75 18
 45 43,75 46,25 25 29 22 27 16,75 23 11,5 19
 50 48,75 51,25 30 34 27 32 21,75 28 16,5 24
 55 53,5 56,5 32 37 26,75 33 21,5 29 16,25 25
 60 58,5 61,5 37 42 31,75 38 26,5 34 21,25 30
 65 63,5 66,5 36,75 43 31,5 39 26,25 35 17 27
 70 68,5 71,5 41,75 48 36,5 44 31,25 40 22 32
 80 78,5 81,5 51,75 58 46,5 54 41,25 50 32 42 21,5 34
 90 88,25 91,75 56,5 64 51,25 60 42 52 31,5 44
100 98,25 101,75 66,5 74 61,25 70 52 62 41,5 54
110 108,25 111,75 71,25 80 62 72 51,5 64
120 118 ,25 121,75 81,25 90 72 82 61,5 74
130 128 132 76 86 65,5 78
140 138 142 86 96 75,5 88
150 148 152 96 106 85,5 98
160 156 164 106 116 95,5 108
180 176 184 115,5 128
200 195,4 204,6 135,5 148
220 215,4 224,6
240 235,4 244,6
260 254,8 265,2
280 274,8 285,2
300 294,8 305,2
320 314,3 325,7
340 334,3 345,7
360 354,3 365,7
380 374,3 385,7
400 394,3 405,7
420 413,7 426,3
440 433,7 446,3
460 453,7 466,3
480 473,7 486,3
500 493,7 506,3
3

---------------------- Page: 13 ----------------------

SIST EN ISO 4016:2002
© ISO
ISO 4016:1999(E)
Table 1 (continued)
(d) M24 M30 M36 M42 M48 M56 M64
Thread
a
3 3,5 4 4,5 5 5,5 6
P
b
54 66 —————
c
b ref. 60 72 84 96 108 — —
d
73 85 97 109 121 137 153
c max. 0,8 0,8 0,8 1111
max. 28,4 35,4 42,4 48,6 56,6 67 75
d
a
max. 24,84 30,84 37 43 49 57,2 65,2
d
s
min. 23,16 29,16 35 41 47 54,8 62,8
min. 33,25 42,75 51,11 59,95 69,45 78,66 88,16
d
w
e min. 39,55 50,85 60,79 71,3 82,6 93,56 104,86
nom. 15 18,7 22,5 26 30 35 40
k max. 15,9 19,75 23,55 27,05 31,05 36,25 41,25
min. 14,1 17,65 21,45 24,95 28,95 33,75 38,75
e
k min. 9,87 12,36 15,02 17,47 20,27 23,63 27,13
w
min. 0,8 1 1 1,2 1,6 2 2
r
s nom. = max. 36 46 55,0 65,0 75,0 85,0 95,0
min. 35 45 53,8 63,1 73,1 82,8 92,8
f g
l
l and l
s g
l l l l l l l l l l l l l l
s g s g s g s g s g s g s g
nom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.
 25 23,95 26,05
 30 28,95 31
...