Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2021)

This document specifies test procedures for the acquisition and presentation of multipoint data on the
following mechanical properties of plastics:
— dynamic modulus;
— tensile properties at constant test speed;
— ultimate stress and strain;
— tensile stress-strain curves;
— tensile creep;
— Charpy impact strength;
— puncture impact behaviour.
The test methods and test conditions apply predominantly to those plastics that can be injection- or
compression-moulded or prepared as sheets of specified thickness from which specimens of the
appropriate size can be machined.

Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil 1: Mechanische Eigenschaften (ISO 11403-1:2021)

Dieses Dokument legt Prüfverfahren für die Ermittlung und Darstellung von Vielpunkt-Kennwerten für folgende mechanische Eigenschaften von Kunststoffen fest:
- Dynamischer Modul;
- Zugeigenschaften bei konstanter Prüfgeschwindigkeit;
- Grenzspannung und -dehnung;
- Spannungs-Dehnungs-Diagramme;
- Kriechverhalten unter Zugbeanspruchung;
- Charpy-Schlagzähigkeit;
- Durchstoßverhalten.
Die Prüfverfahren und Prüfbedingungen treffen vorwiegend auf solche Kunststoffe zu, die durch Spritzgießen oder Formpressen oder als Platten mit vorgegebener Dicke hergestellt werden, aus denen sich Probekörper der erforderlichen Größe fertigen lassen.

Plastiques - Acquisition et présentation de données multiples comparables - Partie 1: Propriétés mécaniques (ISO 11403-1:2021)

Le présent document spécifie des modes opératoires d’essai en vue de l’acquisition et de la présentation de données multiples relatives aux propriétés mécaniques suivantes des plastiques :
—    module dynamique ;
—    propriétés en traction avec vitesse d’essai constante ;
—    contrainte et déformation ultimes ;
—    courbes contrainte-déformation en traction ;
—    fluage en traction ;
—    résistance au choc Charpy ;
—    comportement au choc par perforation.
Ces méthodes et conditions d’essai s’appliquent principalement aux plastiques susceptibles d’être moulés par injection ou compression, ou préparés en feuilles avec une épaisseur spécifiée à partir desquelles il est possible d’usiner des éprouvettes de dimensions appropriées.

Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri različnih pogojih - 1. del: Mehanske lastnosti (ISO 11403-1:2021)

General Information

Status
Published
Public Enquiry End Date
27-Sep-2020
Publication Date
21-Jul-2021
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Jul-2021
Due Date
25-Sep-2021
Completion Date
22-Jul-2021

Relations

Buy Standard

Standard
EN ISO 11403-1:2021
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 11403-1:2020
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11403-1:2021
01-september-2021
Nadomešča:
SIST EN ISO 11403-1:2014
Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri
različnih pogojih - 1. del: Mehanske lastnosti (ISO 11403-1:2021)
Plastics - Acquisition and presentation of comparable multipoint data - Part 1:
Mechanical properties (ISO 11403-1:2021)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil
1: Mechanische Eigenschaften (ISO 11403-1:2021)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 1:
Propriétés mécaniques (ISO 11403-1:2021)
Ta slovenski standard je istoveten z: EN ISO 11403-1:2021
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11403-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 11403-1:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 11403-1:2021


EN ISO 11403-1
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2021
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 11403-1:2014
English Version

Plastics - Acquisition and presentation of comparable
multipoint data - Part 1: Mechanical properties (ISO
11403-1:2021)
Plastiques - Acquisition et présentation de données Kunststoffe - Ermittlung und Darstellung von
multiples comparables - Partie 1: Propriétés vergleichbaren Vielpunkt-Kennwerten - Teil 1:
mécaniques (ISO 11403-1:2021) Mechanische Eigenschaften (ISO 11403-1:2021)
This European Standard was approved by CEN on 6 June 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11403-1:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 11403-1:2021
EN ISO 11403-1:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 11403-1:2021
EN ISO 11403-1:2021 (E)
European foreword
This document (EN ISO 11403-1:2021) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2021, and conflicting national standards
shall be withdrawn at the latest by December 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11403-1:2014.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11403-1:2021 has been approved by CEN as EN ISO 11403-1:2021 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 11403-1:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 11403-1:2021
INTERNATIONAL ISO
STANDARD 11403-1
Fourth edition
2021-06
Plastics — Acquisition and
presentation of comparable
multipoint data —
Part 1:
Mechanical properties
Plastiques — Acquisition et présentation de données multiples
comparables —
Partie 1: Propriétés mécaniques
Reference number
ISO 11403-1:2021(E)
©
ISO 2021

---------------------- Page: 7 ----------------------
SIST EN ISO 11403-1:2021
ISO 11403-1:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 11403-1:2021
ISO 11403-1:2021(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Specimen preparation . 2
5 Conditioning . 3
6 Test requirements . 4
6.1 General . 4
6.2 Dynamic modulus . 4
6.3 Tensile properties at constant test speed . 4
6.3.1 General. 4
6.3.2 Ultimate stress and strain . 5
6.3.3 Tensile stress-strain curves . 5
6.4 Tensile creep . 5
6.5 Charpy impact strength . 5
6.6 Puncture impact behaviour. 6
7 Presentation of data . 6
8 Precision . 8
Bibliography .12
© ISO 2021 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 11403-1:2021
ISO 11403-1:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2,
Mechanical behaviour, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 11403-1:2014), which has been technically
revised. The main changes compared to the previous edition are as follows:
— ISO 13586, ISO 15850 and ISO 17281 are deleted in Bibliography.
A list of all parts in the ISO 11403 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 11403-1:2021
ISO 11403-1:2021(E)

Introduction
This document has been prepared because users of plastics sometimes find that available data cannot
be used readily to compare the properties of similar materials, especially when the data have been
supplied by different sources. Even when the same standard tests have been used, they often allow
the adoption of a wide range of alternative test conditions, and the data obtained are not necessarily
comparable. The purpose of this document is to identify specific methods and conditions of test to be
used for the acquisition and presentation of data in order that valid comparisons between materials
can be made.
[1]
The ISO 10350 series is concerned with single-point data. Such data represent the most basic method
for characterizing materials and are useful for the initial stages of material selection. This document
identifies test conditions and procedures for the measurement and presentation of a more substantial
quantity of data. Each property here is characterized by multipoint data which demonstrate how
that property depends upon important variables such as time, temperature and environmental
effects. Additional properties are also considered in this document. These data therefore enable more
discriminating decisions to be made regarding a material’s suitability for a particular application.
Some data are also considered adequate for undertaking predictions of performance in service and of
optimum processing conditions for moulding a component, although it should be recognized that, for
purposes of design, additional data are often needed. One reason for this is that some properties are
strongly dependent upon the physical structure of the material. The test procedures referred to in this
document employ, where possible, the multipurpose tensile bar, and the polymer structure in this test
specimen can be significantly different from that in specific regions of a moulded component. Under
these circumstances, therefore, the data are not suitable for accurate design calculations for product
performance. The material supplier should be consulted for specific information on the applicability of
data.
ISO 10350 and the ISO 11403 series together define the means for acquiring and presenting a core
set of comparable data for use in material selection. Use of these International Standards should
result in a rationalization of effort and a reduction of cost associated with provision of these data.
Furthermore, reference to these International Standards simplifies the development of data models for
the computerized storage and exchange of data concerning material properties.
Where appropriate, values for test variables have been specified by this document. For some tests
however, owing to the wide range of conditions over which different plastics perform, this document
gives guidance in the selection of certain test conditions so that they cover the operating range for that
polymer. Because, in general, the properties and performance specifications for different polymers
differ widely, there is no obligation to generate data under all the test conditions specified in this
document.
Data on a wide range of properties are needed to enable plastics to be selected and used in the large
variety of applications to which they are suited. ISO standards describe experimental procedures which
are suitable for the acquisition of relevant information on many of these properties. The ISO 11403
series has therefore been divided into parts so that each part can be developed independently. In this
way, additional properties can be included as new or revised standards become available.
© ISO 2021 – All rights reserved v

---------------------- Page: 11 ----------------------
SIST EN ISO 11403-1:2021

---------------------- Page: 12 ----------------------
SIST EN ISO 11403-1:2021
INTERNATIONAL STANDARD ISO 11403-1:2021(E)
Plastics — Acquisition and presentation of comparable
multipoint data —
Part 1:
Mechanical properties
1 Scope
This document specifies test procedures for the acquisition and presentation of multipoint data on the
following mechanical properties of plastics:
— dynamic modulus;
— tensile properties at constant test speed;
— ultimate stress and strain;
— tensile stress-strain curves;
— tensile creep;
— Charpy impact strength;
— puncture impact behaviour.
The test methods and test conditions apply predominantly to those plastics that can be injection- or
compression-moulded or prepared as sheets of specified thickness from which specimens of the
appropriate size can be machined.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small
plates
ISO 295, Plastics — Compression moulding of test specimens of thermosetting materials
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-1, Plastics — Determination of creep behaviour — Part 1: Tensile creep
© ISO 2021 – All rights reserved 1

---------------------- Page: 13 ----------------------
SIST EN ISO 11403-1:2021
ISO 11403-1:2021(E)

ISO 2818, Plastics — Preparation of test specimens by machining
ISO 6603-2, Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented
impact testing
ISO 6721-2, Plastics — Determination of dynamic mechanical properties — Part 2: Torsion-pen
...

SLOVENSKI STANDARD
oSIST prEN ISO 11403-1:2020
01-september-2020
Polimerni materiali - Pridobitev in predstavitev primerljivih podatkov, dobljenih pri
različnih pogojih - 1. del: Mehanske lastnosti (ISO/DIS 11403-1:2020)
Plastics - Acquisition and presentation of comparable multipoint data - Part 1:
Mechanical properties (ISO/DIS 11403-1:2020)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunkt-Kennwerten - Teil
1: Mechanische Eigenschaften (ISO/DIS 11403-1:2020)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 1:
Propriétés mécaniques (ISO/DIS 11403-1:2020)
Ta slovenski standard je istoveten z: prEN ISO 11403-1
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 11403-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 11403-1:2020

---------------------- Page: 2 ----------------------
oSIST prEN ISO 11403-1:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 11403-1
ISO/TC 61/SC 2 Secretariat: KATS
Voting begins on: Voting terminates on:
2020-07-06 2020-09-28
Plastics — Acquisition and presentation of comparable
multipoint data —
Part 1:
Mechanical properties
Plastiques — Acquisition et présentation de données multiples comparables —
Partie 1: Propriétés mécaniques
ICS: 83.080.01
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 11403-1:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020

---------------------- Page: 3 ----------------------
oSIST prEN ISO 11403-1:2020
ISO/DIS 11403-1:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 11403-1:2020
ISO/DIS 11403-1:2020(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Specimen preparation . 2
5 Conditioning . 3
6 Test requirements . 4
6.1 General . 4
6.2 Dynamic modulus: ISO 6721-2 or ISO 6721-4 . 4
6.3 Tensile properties at constant test speed: ISO 527-1 and ISO 527-2. 4
6.3.1 General. 4
6.3.2 Ultimate stress and strain . 4
6.3.3 Tensile stress-strain curves . 5
6.4 Tensile creep: ISO 899-1 . 5
6.5 Charpy impact strength: ISO 179-1 or ISO 179-2 . 5
6.6 Puncture impact behaviour: ISO 6603-2 . 6
7 Presentation of data . 6
8 Precision . 7
Bibliography .12
© ISO 2020 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 11403-1:2020
ISO/DIS 11403-1:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2,
Mechanical behaviour.
This fourth edition cancels and replaces the third edition (ISO 11403-1:2014), which has been technically
revised. The main changes compared to the previous edition are as follows:
— ISO 13586, ISO 15850 and ISO 17281 are deleted in Bibliography.
A list of all parts in the ISO 11403 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 11403-1:2020
ISO/DIS 11403-1:2020(E)

Introduction
This International Standard has been prepared because users of plastics find sometimes that available
data cannot be used readily to compare the properties of similar materials, especially when the data
have been supplied by different sources. Even when the same standard tests have been used, they
often allow the adoption of a wide range of alternative test conditions, and the data obtained are not
necessarily comparable. The purpose of this International Standard is to identify specific methods and
conditions of test to be used for the acquisition and presentation of data in order that valid comparisons
between materials can be made.
ISO 10350 is concerned with single-point data. Such data represent the most basic method for
characterizing materials and are useful for the initial stages of material selection. The present
International Standard identifies test conditions and procedures for the measurement and presentation
of a more substantial quantity of data. Each property here is characterized by multipoint data which
demonstrate how that property depends upon important variables such as time, temperature and
environmental effects. Additional properties are also considered in this standard. These data therefore
enable more discriminating decisions to be made regarding a material’s suitability for a particular
application. Some data are also considered adequate for undertaking predictions of performance
in service and of optimum processing conditions for moulding a component, although it should be
recognized that, for purposes of design, additional data will often be needed. One reason for this is
that some properties are strongly dependent upon the physical structure of the material. The test
procedures referred to in this standard employ, where possible, the multipurpose tensile bar, and the
polymer structure in this test specimen may be significantly different from that in specific regions of
a moulded component. Under these circumstances, therefore, the data will not be suitable for accurate
design calculations for product performance. The material supplier should be consulted for specific
information on the applicability of data.
ISO 10350 and the various parts of this International Standard together define the means for acquiring
and presenting a core set of comparable data for use in material selection. Use of these standards
should result in a rationalization of effort and a reduction of cost associated with provision of these
data. Furthermore, reference to these standards will simplify the development of data models for the
computerized storage and exchange of data concerning material properties.
Where appropriate, values for test variables have been specified by this standard. For some tests
however, owing to the wide range of conditions over which different plastics perform, the standard
gives guidance in the selection of certain test conditions so that they cover the operating range for that
polymer. Because, in general, the properties and performance specifications for different polymers
differ widely, there is no obligation to generate data under all the test conditions specified in this
standard.
Data on a wide range of properties are needed to enable plastics to be selected and used in the large
variety of applications to which they are suited. ISO standards describe experimental procedures which
are suitable for the acquisition of relevant information on many of these properties. The standard
has therefore been divided into parts so that each part can be developed independently. In this way,
additional properties can be included as new or revised standards become available.
© ISO 2020 – All rights reserved v

---------------------- Page: 7 ----------------------
oSIST prEN ISO 11403-1:2020

---------------------- Page: 8 ----------------------
oSIST prEN ISO 11403-1:2020
DRAFT INTERNATIONAL STANDARD ISO/DIS 11403-1:2020(E)
Plastics — Acquisition and presentation of comparable
multipoint data —
Part 1:
Mechanical properties
1 Scope
This document specifies test procedures for the acquisition and presentation of multipoint data on the
following mechanical properties of plastics:
— dynamic modulus;
— tensile properties at constant test speed;
— ultimate stress and strain;
— tensile stress-strain curves;
— tensile creep;
— Charpy impact strength;
— puncture impact behaviour.
The test methods and test conditions apply predominantly to those plastics that can be injection- or
compression-moulded or prepared as sheets of specified thickness from which specimens of the
appropriate size can be machined.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates
ISO 295, Plastics — Compression moulding of test specimens of thermosetting materials
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-1, Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 2818, Plastics — Preparation of test specimens by machining
© ISO 2020 – All rights reserved 1

---------------------- Page: 9 ----------------------
oSIST prEN ISO 11403-1:2020
ISO/DIS 11403-1:2020(E)

ISO 6603-2, Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented
impact testing
ISO 6721-2, Plastics — Determination of dynamic mechanical properties — Part 2: Torsion-pendulum method
ISO 6721-4, Plastics — Determination of dynamic mechanical properties — Part 4: Tensile vibration —
Non-resonance method
ISO 10724-1, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds
(PMCs) — Part 1: General principles and moulding of multipurpose test specimens
ISO 10724-2, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds
(PMCs) — Part 2: Small plates
ISO 20753, Plastics — Test specimens
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
multipoint data
data characterizing the behaviour of a plastics material by means of a number of test results for a
property measured over a range of test conditions
4 Specimen preparation
In the preparation of specimens by injection or compression moulding, the procedures described in
ISO 293, ISO 294-1 and 294-3, ISO 295 or ISO 10724-1 and 10724-2 shall be used. The method of moulding
and the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.