SIST EN ISO 13585:2012
(Main)Brazing - Qualification test of brazers and brazing operators (ISO 13585:2012)
Brazing - Qualification test of brazers and brazing operators (ISO 13585:2012)
This European Standard for the approval testing of brazers (as defined in 3.1) specifies basic requirements essential to the brazing process, test conditions, assessment and certificates. Because of the wide range of applications of brazing this standard does not specify detailed acceptance criteria as these are product-specific and have in each case to be agreed prior to the contract (see clause 4). It is anticipated that, where necessary, specific requirements for individual industries will be developed within this framework and detailed in the relevant application standard. The recommended format for the certificate of approval testing is given in annex A. With regard to the approval test, the brazer should be required to show adequate practical experience and knowledge of the brazing processes, materials and safety requirements for which he is to be approved to a written procedure. This standard applies to hand torch (flame) brazing and only to approval of brazers whose manipulative skills have a direct bearing on the outcome and effectiveness of the brazed joint. It does not apply to those who are not required to apply manipulative skill, since such approval is not normally necessary. If a special professional education and examination in the domestic field included brazing, this standard does not apply to a brazer while he is employed in that field. The certificate of approval testing is issued under the sole responsibility of the examiner or examining body.
Hartlöten - Prüfung von Hartlötern und Bedienern von Hartlöteinrichtungen (ISO 13585:2012)
Die Norm legt die grundlegenden Anforderungen für die Qualifikationsprüfung von Hartlötern und Bedienern
von Hartlöteinrichtungen fest, welche die Bedingungen für das Hartlöten, die Prüfung, die Untersuchung und
den Geltungsbereich der Prüfungsbescheinigung bestimmen.
Diese Norm gilt für das Handlöten, z. B. mit Handbrenner (Flamme), um die Handfertigkeit des Hartlöters
sowie das mechanisierte Hartlöten zu qualifizieren.
Brasage fort - Essais de qualification des braseurs et des opérateurs braseurs en brasage fort (ISO 13585:2012)
L'ISO 13585:2012 définit les exigences de base relatives aux essais de qualification des braseurs et des opérateurs braseurs en brasage fort, et indique les conditions applicables pour le brasage fort, les essais, les contrôles, les critères d'acceptation et le domaine de validité des certificats.
Des lignes directrices sur les exigences générales de qualité relatives au brasage fort sont données dans une annexe, à titre indicatif.
Trdo spajkanje - Certificiranje spajkalcev in upravljavcev (ISO 13585:2012)
Ta mednarodni standard določa osnovne zahteve za certificiranje spajkalcev in upravljavcev ter pogoje za spajkanje, preskušanje in preiskave ter prevzemna merila in razpon kvalifikacije za certifikate.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2012
1DGRPHãþD
SIST EN 13133:2001
Trdo spajkanje - Certificiranje spajkalcev in upravljavcev (ISO 13585:2012)
Brazing - Qualification test of brazers and brazing operators (ISO 13585:2012)
Hartlöten - Prüfung von Hartlötern und Bedienern von Hartlöteinrichtungen (ISO
13585:2012)
Brasage fort - Essais de qualification des braseurs et des opérateurs braseurs en
brasage fort (ISO 13585:2012)
Ta slovenski standard je istoveten z: EN ISO 13585:2012
ICS:
03.100.30 Vodenje ljudi Management of human
resources
25.160.50 Trdo in mehko lotanje Brazing and soldering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 13585
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2012
ICS 25.160.01 Supersedes EN 13133:2000
English Version
Brazing - Qualification test of brazers and brazing operators
(ISO 13585:2012)
Brasage fort - Essais de qualification des braseurs et des Hartlöten - Prüfung von Hartlötern und Bedienern von
opérateurs braseurs en brasage fort (ISO 13585:2012) Hartlöteinrichtungen (ISO 13585:2012)
This European Standard was approved by CEN on 24 May 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13585:2012: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 97/23/EC .4
Foreword
This document (EN ISO 13585:2012) has been prepared by Technical Committee CEN/TC 121 “Welding", the
secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 44 "Welding and allied
processes".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2012, and conflicting national standards shall be withdrawn
at the latest by December 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13133:2000.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland, Turkey and the United Kingdom.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 97/23/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive 97/23/EC, Pressure equipment.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
corresponding Essential Requirements of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European standard and the Directive 97/23/EC
Clauses/Paragraphs of this Essential requirement of the Comments/Notes
European standard Directive 97/23/EEC
All normative clauses Annex I, 3.1.2 Permanent joining
WARNING — Other requirements and other EU Directives may be applicable to the products falling
within the scope of this standard.
INTERNATIONAL ISO
STANDARD 13585
First edition
2012-06-15
Brazing — Qualification test of brazers
and brazing operators
Brasage fort — Essais de qualification des braseurs et des opérateurs
braseurs en brasage fort
Reference number
ISO 13585:2012(E)
©
ISO 2012
ISO 13585:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 13585:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols, definitions and reference numbers . 3
4.1 General . 3
4.2 Symbols . 3
4.3 Reference numbers . 3
5 Essential variables and range of qualification . 3
5.1 General . 3
5.2 Brazing process . 3
5.3 Product type . 4
5.4 Type of joint . 4
5.5 Parent material group(s) . 4
5.6 Filler metals and brazing filler application . 5
5.7 Dimensions . 5
5.8 Filler metal flow direction . 6
5.9 Degree of mechanization . 6
6 Examination and testing . 7
6.1 Supervision . 7
6.2 Brazing conditions . 7
6.3 Test piece . 7
6.4 Assessment of work pieces . 7
6.5 Extent of testing . 7
6.6 Visual testing . 7
6.7 Non-destructive testing . 8
6.8 Destructive testing . 8
6.9 Additional examination and testing. 8
7 Acceptance requirements for test pieces . 8
8 Re-tests . 8
9 Period of validity . 8
9.1 Initial qualification . 8
9.2 Prolongation . 9
10 Certificate . 9
11 Designation . 9
Annex A (informative) Brazer qualification test certificate . 11
Annex B (informative) Brazer operator qualification test certificate .12
Annex C (informative) Examples of test pieces.13
Annex D (informative) Quality requirements for brazing .15
Annex E (informative) Other non-essential variables .16
Bibliography .17
ISO 13585:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.