SIST EN IEC 61076-2-012:2020
(Main)Connectors for electrical and electronic equipment - Product Requirements - Part 2-012: Circular connectors - Detail specification for connectors with inner push-pull locking based on M12 connector interfaces according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 and IEC 61076-2-113 (IEC 61076-2-012:2020)
Connectors for electrical and electronic equipment - Product Requirements - Part 2-012: Circular connectors - Detail specification for connectors with inner push-pull locking based on M12 connector interfaces according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 and IEC 61076-2-113 (IEC 61076-2-012:2020)
This part of IEC 61076 specifies circular connectors with an inner push‑pull locking
mechanism of a size derived from and thus being compatible with M12 screw‑locking
connectors and with mating interfaces according to IEC 61076‑2‑101, IEC 61076‑2‑109,
IEC 61076‑2‑111 and IEC 61076‑2‑113.
A female fixed connector with inner push-pull locking according to this document is
intermateable with a correspondingly coded male free connector with M12 screw-locking
according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 or IEC 61076-2-113.
NOTE 1 M12 is the dimension of the thread of the screw‑locking mechanism of circular connectors with M12
screw‑locking.
This document covers both:
a) power connectors with current ratings up to 16 A and voltage ratings up to 630 V, typically
used for power supply of electrical equipment used in industrial premises, and
b) connectors for data and signal transmission with frequencies up to 500 MHz.
NOTE 2 The power connectors are not suitable as power distribution socket-outlets in electrical installations of
buildings.
These connectors consist of both fixed and free connectors, either rewirable or non‑rewirable,
with M12 inner push‑pull locking as explained above. Male connectors have round contacts
from Ø0,6 mm up to Ø1,5 mm.
This document covers various types of connectors identified by their "codings" with different
contact arrangement, not mutually interchangeable.
The design of the inner push‑pull mechanism prevents the unintended mating of the male
inner push‑pull free connector with the female connector with M12 screw‑locking even for
identical coding.
Some styles of free connectors with female contacts covered in this document are equipped
with both inner and outer push-pull locking for intermateability also with correspondingly
coded male fixed or free connectors according to IEC 61076-2-010.
Steckverbinder für elektrische und elektronische Einrichtungen - Produktanforderungen – Teil 2-012: Rundsteckverbinder – Bauartspezifikation für Steckverbinder mit innerer Push-pull-Verriegelung auf Basis Steckverbindern mit Schraubverriegelungen M12 nach IEC 61076-101, IEC 61076-109, IEC 61076-111 und IEC 61076-113 (IEC 61076-2-012:2020)
Connecteurs pour équipements électriques et électroniques - Exigences de produit - Partie 2-012 : Connecteurs circulaires - Spécification particulière relative aux connecteurs avec verrouillage interne de type pousser-tirer fondée sur les interfaces de connecteur M12 conformément à l’IEC 61076-2-101, l’IEC 61076-2-109, l’IEC 61076-2-111 et l’IEC 61076 -2-113 (IEC 61076-2-012:2020)
IEC 61076-2-012:2020 décrit les connecteurs circulaires équipés d’un mécanisme de verrouillage interne de type pousser-tirer dérivé des connecteurs à verrouillage à vis M12 et par conséquent compatible avec ces derniers, et avec des interfaces d’accouplement conformément à l’IEC 61076-2-101, l’IEC 61076-2-109, l’IEC 61076-2-111 et l’IEC 61076-2-113.
Une embase femelle équipée d’un verrouillage interne de type pousser-tirer conformément au présent document est accouplable à une fiche mâle codée en conséquence avec verrouillage à vis M12 conformément à l’IEC 61076-2-101, l’IEC 61076-2-109, l’IEC 61076-2-111 ou l’IEC 61076-2-113.
Le présent document couvre à la fois:
a) les connecteurs d’alimentation avec des caractéristiques assignées de courant de 16 A maximum et des caractéristiques assignées de tension de 630 V maximum, généralement utilisés pour l'alimentation des équipements électriques utilisés dans les locaux industriels, et
b) les connecteurs pour la transmission de données et de signal avec des fréquences maximales de 500 MHz.
Ces connecteurs se composent à la fois d’embases et de fiches, démontables ou non, avec verrouillage interne M12 de type pousser-tirer, comme cela est expliqué ci-dessus. Les connecteurs mâles possèdent des contacts arrondis de 0,60 mm à 1,5 mm de diamètre.
Le présent document couvre plusieurs types de connecteurs identifiés par leurs "codages" et présentant différentes dispositions de contact non interchangeables.
La conception du mécanisme interne de type pousser-tirer empêche l’accouplement fortuit de la fiche interne de type pousser-tirer mâle au connecteur femelle avec verrouillage à vis M12, même pour un codage identique.
Certains modèles de fiches à contacts femelles couverts dans le présent document sont équipés d'un verrouillage interne et externe de type pousser-tirer pour une compatibilité d’accouplement, ainsi que de fiches ou embases mâles codés en conséquence, conformément à l’IEC 61076-2-010.
Konektorji za električno in elektronsko opremo - Zahteve za izdelek - 2-012. del: Okrogli konektorji - Podrobna specifikacija za konektorje z notranjim potisnim zaklepanjem na podlagi vmesnikov M12 v skladu z IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 in IEC 61076-2-113 (IEC 61076-2-012:2020)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 61076-2-012:2020
01-november-2020
Konektorji za električno in elektronsko opremo - Zahteve za izdelek - 2-012. del:
Okrogli konektorji - Podrobna specifikacija za konektorje z notranjim potisnim
zaklepanjem na podlagi vmesnikov M12 v skladu z IEC 61076-2-101, IEC 61076-2-
109, IEC 61076-2-111 in IEC 61076-2-113 (IEC 61076-2-012:2020)
Connectors for electrical and electronic equipment - Product Requirements - Part 2-012:
Circular connectors - Detail specification for connectors with inner push-pull locking
based on M12 connector interfaces according to IEC 61076-2-101, IEC 61076-2-109,
IEC 61076-2-111 and IEC 61076-2-113 (IEC 61076-2-012:2020)
Steckverbinder für elektrische und elektronische Einrichtungen - Produktanforderungen –
Teil 2-012: Rundsteckverbinder – Bauartspezifikation für Steckverbinder mit innerer
Push-pull-Verriegelung auf Basis Steckverbindern mit Schraubverriegelungen M12 nach
IEC 61076-101, IEC 61076-109, IEC 61076-111 und IEC 61076-113 (IEC 61076-2-
012:2020)
Connecteurs pour équipements électriques et électroniques - Exigences de produit -
Partie 2-012 : Connecteurs circulaires - Spécification particulière relative aux
connecteurs avec verrouillage interne de type pousser-tirer fondée sur les interfaces de
connecteur M12 conformément à l’IEC 61076-2-101, l’IEC 61076-2-109, l’IEC 61076-2-
111 et l’IEC 61076 -2-113 (IEC 61076-2-012:2020)
Ta slovenski standard je istoveten z: EN IEC 61076-2-012:2020
ICS:
31.220.10 Vtiči in vtičnice, konektorji Plug-and-socket devices.
Connectors
SIST EN IEC 61076-2-012:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 61076-2-012:2020
---------------------- Page: 2 ----------------------
SIST EN IEC 61076-2-012:2020
EUROPEAN STANDARD EN IEC 61076-2-012
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2020
ICS 31.220.10
English Version
Connectors for electrical and electronic equipment - Product
Requirements - Part 2-012: Circular connectors - Detail
specification for connectors with inner push-pull locking based
on M12 connector interfaces according to IEC 61076-2-101, IEC
61076-2-109, IEC 61076-2-111 and IEC 61076-2-113
(IEC 61076-2-012:2020)
Connecteurs pour équipements électriques et électroniques Steckverbinder für elektrische und elektronische
- Exigences de produit - Partie 2-012 : Connecteurs Einrichtungen - Produktanforderungen - Teil 2-012:
circulaires - Spécification particulière relative aux Rundsteckverbinder - Bauartspezifikation für
connecteurs avec verrouillage interne de type pousser-tirer Steckverbinder mit innerer Push-pull-Verriegelung auf Basis
fondée sur les interfaces de connecteur M12 conformément Steckverbindern mit Schraubverriegelungen M12 nach IEC
à l'IEC 61076-2-101, l'IEC 61076-2-109, l'IEC 61076-2-111 61076-101, IEC 61076-109, IEC 61076-111 und IEC
et l'IEC 61076 -2-113 61076-113
(IEC 61076-2-012:2020) (IEC 61076-2-012:2020)
This European Standard was approved by CENELEC on 2020-08-31. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61076-2-012:2020 E
---------------------- Page: 3 ----------------------
SIST EN IEC 61076-2-012:2020
EN IEC 61076-2-012:2020 (E)
European foreword
The text of document 48B/2813/FDIS, future edition 1 of IEC 61076-2-012, prepared by SC 48B
"Electrical connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical
and electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 61076-2-012:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-05-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-08-31
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61076-2-012:2020 was approved by CENELEC as a
European Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN IEC 61076-2-012:2020
EN IEC 61076-2-012:2020 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-581 2008 International Electrotechnical Vocabulary - - -
Part 581: Electromechanical components
for electronic equipment
IEC 60068-1 - Environmental testing - Part 1: General EN 60068-1 -
and guidance
IEC 60512-2-1 - Connectors for electronic equipment - EN 60512-2-1 -
Tests and measurements - Part 2-1:
Electrical continuity and contact resistance
tests - Test 2a: Contact resistance -
Millivolt level method
IEC 60512-3-1 - Connectors for electronic equipment - EN 60512-3-1 -
Tests and measurements - Part 3-1:
Insulation tests - Test 3a: Insulation
resistance
IEC 60512-4-1 - Connectors for electronic equipment - EN 60512-4-1 -
Tests and measurements - Part 4-1:
Voltage stress tests - Test 4a: Voltage
proof
IEC 60512-5-1 - Connectors for electronic equipment - EN 60512-5-1 -
Tests and measurements - Part 5-1:
Current-carrying capacity tests - Test 5a:
Temperature rise
IEC 60512-6-3 - Connectors for electronic equipment - EN 60512-6-3 -
Tests and measurements - Part 6-3:
Dynamic stress tests - Test 6c: Shock
IEC 60512-6-4 - Connectors for electronic equipment - EN 60512-6-4 -
Tests and measurements - Part 6-4:
Dynamic stress tests - Test 6d: Vibration
(sinusoidal)
IEC 60512-9-1 - Connectors for electronic equipment - EN 60512-9-1 -
Tests and measurements - Part 9-1:
Endurance tests - Test 9a: Mechanical
operation
3
---------------------- Page: 5 ----------------------
SIST EN IEC 61076-2-012:2020
EN IEC 61076-2-012:2020 (E)
IEC 60512-13-1 - Connectors for electronic equipment - EN 60512-13-1 -
Tests and measurements - Part 13-1:
Mechanical operation tests - Test 13a:
Engaging and separating forces
IEC 60512-13-2 - Connectors for electronic equipment - EN 60512-13-2 -
Tests and measurements - Part 13-2:
Mechanical operation tests - Test 13b:
Insertion and withdrawal forces
IEC 60512-13-5 - Connectors for electronic equipment - EN 60512-13-5 -
Tests and measurements - Part 13-5:
Mechanical operation tests - Test 13e:
Polarizing and keying method
IEC 60512-15-6 - Connectors for electronic equipment - EN 60512-15-6 -
Tests and measurements - Part 15-6:
Connector tests (mechanical) - Test 15f:
Effectiveness of connector coupling
devices
IEC 60529 1989 Degrees of protection provided by EN 60529 1991
enclosures (IP Code)
- - + corrigendum May 1993
+ A1 1999 + A1 2000
+ A2 2013 + A2 2013
IEC 60664-1 - Insulation coordination for equipment EN IEC 60664-1 -
within low-voltage supply systems - Part 1:
Principles, requirements and tests
IEC 60998-2-12002 Connecting devices for low-voltage circuits EN 60998-2-1 2004
(mod) for household and similar purposes - Part
2-1: Particular requirements for connecting
devices as separate entities with screw-
type clamping units
IEC 61076-1 2006 Connectors for electronic equipment - EN 61076-1 2006
Product requirements - Part 1: Generic
specification
IEC 61076-2-010 - Connectors for electrical and electronic - -
equipment - Product requirements - Part 2-
010: Circular connectors - Detail
specification for push pull connectors with
outer locking mechanism, based on mating
interfaces according to IEC 61076-2-101,
IEC 61076-2-109, IEC 61076-2-111 and
IEC 61076-2-113
IEC 61076-2-101 2012 Connectors for electronic equipment - EN 61076-2-101 2012
Product requirements - Part 2-101: Circular
connectors - Detail specification for M12
connectors with screw-locking
IEC 61076-2-109 2014 Connectors for electronic equipment - EN 61076-2-109 2014
Product requirements - Part 2-109: Circular
connectors - Detail specification for
connectors with M 12 x 1 screw-locking, for
data transmission frequencies up to 500
MHz
4
---------------------- Page: 6 ----------------------
SIST EN IEC 61076-2-012:2020
EN IEC 61076-2-012:2020 (E)
IEC 61076-2-111 2017 Connectors for electrical and electronic EN IEC 61076-2-2018
equipment - Product requirements - Part 2-111
111: Circular connectors - Detail
specification for power connectors with
M12 screw-locking
IEC 61076-2-113 2017 Connectors for electronic equipment - EN 61076-2-113 2017
Product requirements - Part 2-113: Circular
connectors - Detail specification for
connectors with M12 screw locking with
power and signal contacts for data
transmission with frequency up to 100 MHz
IEC 61984 - Connectors - Safety requirements and EN 61984 -
tests
5
---------------------- Page: 7 ----------------------
SIST EN IEC 61076-2-012:2020
---------------------- Page: 8 ----------------------
SIST EN IEC 61076-2-012:2020
IEC 61076‑2‑012
®
Edition 1.0 2020-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electrical and electronic equipment – Product requirements –
Part 2‑012: Circular connectors – Detail specification for connectors with inner
push‑pull locking based on M12 connector interfaces according to
IEC 61076‑2‑101, IEC 61076‑2‑109, IEC 61076‑2‑111 and IEC 61076‑2‑113
Connecteurs pour équipements électriques et électroniques – Exigences de
produit –
Partie 2-012: Connecteurs circulaires – Spécification particulière relative aux
connecteurs avec verrouillage interne de type pousser-tirer fondée sur les
interfaces de connecteur M12 conformément à l’IEC 61076-2-101,
l’IEC 61076‑2‑109, l’IEC 61076-2-111 et l’IEC 61076-2-113
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.220.10 ISBN 978-2-8322-8643-2
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 9 ----------------------
SIST EN IEC 61076-2-012:2020
– 2 – IEC 61076‑2‑012:2020 © IEC 2020
CONTENTS
FOREWORD . 7
1 Scope . 10
2 Normative references . 10
3 Terms and definitions . 12
4 Technical information . 12
4.1 Systems of levels . 12
4.1.1 Performance levels . 12
4.1.2 Compatibility levels, according to IEC 61076‑1 . 13
4.2 Classification into climatic categories . 13
4.3 Contact terminations . 13
4.4 Available connector codings . 14
4.5 Ratings . 15
4.6 Marking . 15
4.7 Safety aspects . 15
5 Dimensional information . 15
5.1 General . 15
5.2 Survey of styles and variants . 15
5.2.1 General . 15
5.2.2 Fixed connectors . 15
5.2.3 Free connectors . 21
5.3 Interface dimensions . 34
5.3.1 Push‑pull housing . 34
5.3.2 A‑coding . 38
5.3.3 B‑coding . 39
5.3.4 C‑coding . 40
5.3.5 D‑coding . 41
5.3.6 P‑coding . 42
5.3.7 H‑coding . 43
5.3.8 X‑coding . 44
5.3.9 K‑coding . 45
5.3.10 L‑coding . 46
5.3.11 M‑coding . 47
5.3.12 S‑coding . 48
5.3.13 T‑coding . 49
5.3.14 Type 1‑coding . 50
5.3.15 Type 2‑coding . 51
5.3.16 Type 3‑coding . 52
5.3.17 Type 4‑coding . 53
5.4 Gauges – Sizing gauges and retention force gauges . 54
6 Characteristics . 54
6.1 Classification into climatic category . 54
6.2 Electrical characteristics . 54
6.2.1 Voltage proof . 54
6.2.2 Rated voltage – Rated impulse voltage – Pollution degree . 55
6.2.3 Current‑carrying capacity . 55
6.2.4 Contact resistance . 55
---------------------- Page: 10 ----------------------
SIST EN IEC 61076-2-012:2020
IEC 61076‑2‑012:2020 © IEC 2020 – 3 –
6.2.5 Insulation resistance. 55
6.2.6 Transmission performance . 55
6.3 Mechanical characteristics . 55
6.3.1 Mating Interface . 55
6.3.2 Push‑pull locking mechanism . 56
6.4 Other characteristics . 57
6.4.1 Vibration (sinusoidal) . 57
6.4.2 Shock . 57
6.4.3 Degree of protection provided by enclosures (IP code) . 57
7 Test schedule . 57
7.1 General . 57
7.2 Test schedule . 58
7.2.1 Test group P – Preliminary . 58
7.2.2 Test group AP – Dynamic/Climatic . 58
7.2.3 Test group BP – Mechanical endurance . 58
7.2.4 Test group CP – Electrical load . 59
7.2.5 Test group DP – Chemical resistivity . 59
7.2.6 Test group EP – Connection method tests . 59
7.2.7 Test group FP – Electrical transmission requirements . 59
Annex A (normative) Inner diameter of the male push‑pull connector body . 60
Figure 1 – Style EF_M12_PPI – Fixed connector, female contacts, with inner push‑pull
and screw locking, mounting with thread M12 × 1, with wire/cable ends, single hole
mounting thread M16 × 1,5 . 16
Figure 2 – Style FF_M12_PPI – Fixed connector, female contacts, with inner push‑pull
and screw locking, mounting with thread M12 × 1, with wire/cable ends, single hole
mounting thread M20 × 1,5 . 17
Figure 3 – Style GF_M12_PPI – Fixed connector, female contacts, with inner
push‑pull and screw locking, mounting with thread M12 × 1, with wire/cable ends,
single hole mounting thread M16 × 1,5, mounting orientation . 18
Figure 4 – Style HF_M12_PPI – Fixed connector, female contacts, with inner push‑pull
and screw locking, mounting with thread M12 × 1, with wire/cable ends, single hole
mounting thread M20 × 1,5, mounting orientation . 19
Figure 5 – Style IF_M12_PPI – Fixed connector, female contacts, with inner push‑pull
and screw locking, mounting with thread M12 × 1, with wire/cable ends, single hole
mounting thread M17 × 1,0, rear orientation . 20
Figure 6 – Style JM_PPI – Rewirable connector, male contacts, straight version, with
inner push‑pull locking . 22
Figure 7 – Style KM_PPI – Rewirable connector, male contacts, right‑angled version,
with inner push‑pull locking . 23
Figure 8 – Style LM_PPI – Non‑rewirable connector, male contacts, straight version,
with inner push‑pull locking . 24
Figure 9 – Style MM_PPI – Non‑rewirable connector, male contacts, right‑angled
version, with inner push‑pull locking . 24
Figure 10 – Style NM_PPI – Non‑rewirable connector, male contacts, right angled
higher version, with inner push‑pull locking . 25
Figure 11 – Style JF_M12_PPI – Rewireable connector, with female contacts, straight
version, with inner push‑pull and screw locking . 26
Figure 12 – Style KF_M12_PPI – Rewireable connector, with female contacts,
right‑angled version, with inner push‑pull and screw locking . 26
---------------------- Page: 11 ----------------------
SIST EN IEC 61076-2-012:2020
– 4 – IEC 61076‑2‑012:2020 © IEC 2020
Figure 13 – Style LF_M12_PPI – Non‑rewireable connector, with female contacts,
straight version, with inner push‑pull and screw locking . 27
Figure 14 – Style MF_M12_PPI – Non‑rewireable connector, with female contacts,
right‑angled version, with inner push‑pull and screw locking . 28
Figure 15 – Style NF_M12_PPI – Non‑rewirable connector, female contacts, right
angled higher version, with inner push‑pull and screw locking . 29
Figure 16 – Style JF_PPI_PPO – Rewireable connector, with female contacts, straight
version, with inner and outer push‑pull locking . 30
Figure 17 – Style KF_PPI_PPO – Rewireable connector, with female contacts,
right‑angled version, with inner and outer push‑pull locking . 30
Figure 18 – Style LF_PPI_PPO – Non‑rewireable connector, with female contacts,
straight version, with inner and outer push‑pull locking . 31
Figure 19 – Style MF_PPI_PPO – Non‑rewireable connector, with female contacts,
right‑angled version, with inner and outer push‑pull locking . 32
Figure 20 – Style NF_PPI_PPO – Non‑rewirable connector, female contacts, right
angled higher version, with inner and outer push‑pull locking . 33
Figure 21 – Front view of the female side of the push‑pull housing using the example
of an A‑coded connector . 34
Figure 22 – Side view of the female side of the push‑pull housing using the example of
an A‑coded connector . 35
Figure 23 – Front view of the male side of the push‑pull housing using the example of
a D‑coded connector . 37
Figure 24 – Side view of the male side of the push‑pull housing using the example of a
D‑coded connector . 37
Figure 25 – Front view of the female side of the push‑pull housing for A‑coding. 38
Figure 26 – Side view of the female side of the push‑pull housing for A‑coding . 39
Figure 27 – Front view of the female side of the push‑pull housing for B‑coding. 39
Figure 28 – Side view of the female side of the push‑pull housing for B‑coding . 40
Figure 29 – Front view of the female side of the push‑pull housing for C‑coding . 40
Figure 30 – Side view of the female side of the push‑pull housing for C‑coding. 41
Figure 31 – Front view of the female side of the push‑pull housing for D‑coding . 41
Figure 32 – Side view of the female side of the push‑pull housing for D‑coding. 42
Figure 33 – Front view of the female side of the push‑pull housing for P‑coding. 42
Figure 34 – Side view of the female side of the push‑pull housing for P‑coding . 43
Figure 35 – Front view of the female side of the push‑pull housing for H‑coding . 43
Figure 36 – Side view of the female side of the push‑pull housing for H‑coding. 44
Figure 37 – Front view of the female side of the push‑pull housing for X‑coding. 44
Figure 38 – Side view of the female side of the push‑pull housing for X‑coding . 45
Figure 39 – Front view of the female side of the push‑pull housing for K‑coding. 45
Figure 40 – Side view of the female side of the push‑pull housing for K‑coding . 46
Figure 41 – Front view of the female side of the push‑pull housing for L‑coding . 46
Figure 42 – Side view of the female side of the push‑pull housing for L‑coding . 47
Figure 43 – Front view of the female side of the push‑pull housing for M‑coding . 47
Figure 44 – Side view of the female side of the push‑pull housing for M‑coding . 48
Figure 45 – Front view of the female side of the push‑pull housing for S‑coding. 48
Figure 46 – Side view of the female side of the push‑pull housing for S‑coding . 49
---------------------- Page: 12 ----------------------
SIST EN IEC 61076-2-012:2020
IEC 61076‑2‑012:2020 © IEC 2020 – 5 –
Figure 47 – Front view of the female side of the push‑pull housing for T‑coding . 49
Figure 48 –Side view of the female side of the push‑pull housing for T‑coding . 50
Figure 49 – Front view of the female side of the push‑pull housing for Type 1 . 50
Figure 50 – Side view of the female side of the push‑pull housing for Type 1 . 51
Figure 51 – Front view of the female side of the push‑pull housing for Type 2 . 51
Figure 52 – Side view of the female side of the push‑pull housing for Type 2 . 52
Figure 53 – Front view of the female side of the push‑pull housing for Type 3 . 52
Figure 54 – Side view of the female side of the push‑pull housing for Type 3 . 53
Figure 55 – Front view of the female side of the push‑pull housing for Type 4 . 53
Figure 56 – Side view of the female side of the push‑pull housing for Type 4 . 54
Figure A.1 – Inner diameter of the free male connector body . 60
Table 1 – Available connector codings . 14
Table 2 – Styles of fixed c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.