SIST EN ISO 17078-1:2005

Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels (ISO 17078-1:2004)

ISO 17078:2004 provides requirements for side-pocket mandrels used in the petroleum and natural gas industry. This part of ISO 17078 includes specifying, selecting, designing, manufacturing, quality control, testing, and preparation for shipping of side-pocket mandrels.
This part of ISO 17078:2004 does not address nor include requirements for end connections between the side-pocket mandrels and the well conduit. The installation and retrieval of side-pocket mandrels is outside the scope of this part of ISO 17078:2004. Additionally, this part of ISO 17078:2004 does not include specifications for centre-set mandrels, or mandrels that employ or support tubing-retrievable flow control devices.
This part of ISO 17078:2004 does not include gas-lift or any other flow-control valves or devices, latches, and/or associated wire line equipment that can or cannot be covered in other ISO specifications.
The side-pocket mandrels to which this part of ISO 17078:2004 refers are independent devices that can accept installation of flow-control or other devices down-hole.

Erdöl- und Erdgasindustrie - Bohr-und Fördereinrichtungen - Teil 1: Seitentaschen-Rohre (ISO 17078-1:2004

Dieser Teil der ISO 17078 legt Anforderungen an Seitentaschen-Rohre für die Erdöl- und Erdgasindustrie fest. Dieser Teil der ISO 17078 umfasst technische Festlegungen, die Auswahl, Konstruktion, Herstellung, Qualitätslenkung, Prüfung sowie die Vorbereitung zum Versand für Seitentaschen-Rohre.
Dieser Teil der ISO 17078 enthält keine Anforderungen für die Verbindungen zwischen den Seitentaschen-Rohren und den Bohrungsleitungen. Der Ein- und Ausbau von Seitentaschen-Rohren liegt nicht im Anwendungsbereich dieses Teil der ISO 17078. Des weiteren enthält die vorliegende Norm keine Festlegungen für Seitentaschen-Rohre, die zentriert sind oder Rohre mit steigrohrziehbaren Durchfluss-Regeleinrichtungen.
Dieser Teil der ISO 17078 enthält keine Festlegungen für Gaslift-Vorrichtungen oder sonstige Durchfluss-Regelventile oder Einrichtungen, Verriegelungen und/oder zugehörige drahtseilgeführte Werkzeuge, die
eventuell in anderen ISO-Normen enthalten sind.
Die in dieser Norm festgelegten Seitentaschen-Rohre sind unabhängige Einrichtungen, in die Durchfluss-Regel- oder andere Einrichtungen unter Wasser eingebaut werden können.

Industries du pétrole et du gaz naturel - Equipement de forage et de production - Partie 1: Raccords a poche latérale (ISO 17078:2004)

L'ISO 17078-1:2004 fournit des exigences relatives aux raccords à poche latérale utilisés dans les industries du pétrole et du gaz naturel. Elle porte sur la spécification, la sélection, la conception, la fabrication, la maîtrise de la qualité, les essais et la préparation avant l'expédition des raccords à poche latérale.
Aucune exigence relative aux raccordements d'extrémité entre les raccords à poche latérale et le conduit du puits n'est traitée dans l'ISO 17078-1:2004. L'installation et le retrait des raccords à poche latérale ne sont pas couverts par le domaine d'application de la présente partie de l'ISO 17078-1:2004. De plus, les spécifications relatives aux raccords placés au centre, ou aux raccords qui utilisent ou supportent des dispositifs de régulation de la vitesse d'écoulement récupérables dans les tubes, ne sont pas couvertes.
L'ISO 17078-1:2004 ne traite pas de l'extraction au gaz ou d'autres vannes ou dispositifs de régulation de la vitesse d'écoulement, des verrous et/ou des équipements à câble de forage associés qui peuvent éventuellement être couverts par d'autres spécifications ISO.
Les raccords à poche latérale auxquels l'ISO 17078-1:2004 se rapporte sont des dispositifs indépendants qui permettent l'installation de dispositifs de régulation de la vitesse d'écoulement ou d'autres dispositifs en fond de trou.

Industrija za predelavo nafte in zemeljskega plina - Vrtalna in proizvodna oprema - 1. del: Vpenjalna os s stranskimi žepi (ISO 17078-1:2004)

Ta del ISO 17078 podaja zahteve za vpenjalne osi s stranskimi žepi, ki se uporabljajo v industriji za predelavo nafte in zemeljskega plina. Ta del ISO 17078 zajema določanje, izbiranje, načrtovanje, izdelovanje, nadzor kakovosti, preskušanje in pripravo za transport vpenjalnih osi s stranskimi žepi.  Ta del ISO 17078 se ne ukvarja in ne zajema zahtev za končne priključke med vpenjalnimi osmi s stranskimi žepi in vodom vrtine. Namestitev in ponovna uporaba vpenjalnih osi s stranskimi žepi je izven področja tega dela ISO 17078. Poleg tega ta del ISO 17078 ne zajema specifikacij za centralno nameščene vpenjalne osi ali vpenjalne osi, ki uporabljajo ali podpirajo regulatorje pretoka z obnovljivimi cevovodi. Ta del ISO 17078 ne zajema plinskih dvižnikov ali kakršnih koli drugih ventilov ali naprav za nadzor pretoka, zapahov in/ali povezane žične opreme, ki jih lahko ali ne zajemajo druge ISO specifikacije. Vpenjalne osi s stranskim žepi, na katere se nanaša ta del ISO 17078, so neodvisne naprave, ki lahko sprejmejo namestitev regulatorjev pretoka ali drugih naprav v vrtini.

General Information

• Status: Published
• Publication Date: 31-Mar-2005
• ICS: 75.180.10 - Exploratory, drilling and extraction equipment
• Technical Committee: SS SPL - Technical Board for the general field
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Apr-2005
• Due Date: 01-Apr-2005
• Completion Date: 01-Apr-2005
• Ref Project: EN ISO 17078-1:2004 - Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels (ISO 17078-1:2004)

Relations

• Amended By: SIST EN ISO 17078-1:2005/A1:2010 - Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels - Amendment 1 (ISO 17078-1:2004/Amd 1:2010)
• Effective Date: 01-May-2010

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 17078-1:2005
01-april-2005
Industrija za predelavo nafte in zemeljskega plina - Vrtalna in proizvodna oprema -
1. del: Vpenjalna os s stranskimi žepi (ISO 17078-1:2004)
Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-
pocket mandrels (ISO 17078-1:2004)
Erdöl- und Erdgasindustrie - Bohr-und Fördereinrichtungen - Teil 1: Seitentaschen-Rohre
(ISO 17078-1:2004
Industries du pétrole et du gaz naturel - Equipement de forage et de production - Partie
1: Raccords a poche latérale (ISO 17078:2004)
Ta slovenski standard je istoveten z: EN ISO 17078-1:2004
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
SIST EN ISO 17078-1:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 17078-1:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 17078-1:2005
EUROPEAN STANDARD
EN ISO 17078-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2004
ICS 75.180.10
English version
Petroleum and natural gas industries - Drilling and production
equipment - Part 1: Side-pocket mandrels (ISO 17078-1:2004)
Industries du pétrole et du gaz naturel - Equipement de
forage et de production - Partie 1: Raccords à poche
latérale (ISO 17078:2004)
This European Standard was approved by CEN on 17 November 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17078-1:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 17078-1:2005
EN ISO 17078-1:2004 (E)



Foreword

This document (EN ISO 17078-1:2004) has been prepared by Technical Committee ISO/TC
67 "Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum and natural gas industries", the secretariat of which is held by
AFNOR.

This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by June 2005, and conflicting national
standards shall be withdrawn at the latest by June 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 17078-1:2004 has been approved by CEN as EN ISO 17078-1:2004 without
any modifications.


2

---------------------- Page: 4 ----------------------

SIST EN ISO 17078-1:2005


INTERNATIONAL ISO
STANDARD 17078-1
First edition
2004-12-15


Petroleum and natural gas industries —
Drilling and production equipment —
Part 1:
Side-pocket mandrels
Industries du pétrole et du gaz naturel — Équipement de forage et de
production —
Partie 1: Raccords à poche latérale




Reference number
ISO 17078-1:2004(E)
©
ISO 2004

---------------------- Page: 5 ----------------------

SIST EN ISO 17078-1:2005
ISO 17078-1:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 17078-1:2005
ISO 17078-1:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Abbreviated terms. 7
5 Functional specification. 7
5.1 General. 7
5.2 Functional characteristics. 7
5.3 Well parameters. 8
5.4 Operational parameters. 9
5.5 Compatibility with related well devices . 9
5.6 Environmental service classes. 10
5.7 Design validation. 10
5.8 Product functional testing grades. 10
5.9 Quality-control grades. 10
5.10 Additional requirements. 10
6 Technical specification. 11
6.1 General. 11
6.2 Technical characteristics. 11
6.3 Design criteria. 12
6.4 Design verification. 13
6.5 Allowable design changes . 13
6.6 Design validation. 14
6.7 Product-functional testing requirements . 14
7 Supplier/manufacturer requirements. 15
7.1 General. 15
7.2 Documentation and data control. 15
7.3 Product identification requirements . 17
7.4 Quality-control requirement. 17
7.5 Heat treatment requirements . 19
7.6 Welding requirements. 20
7.7 Non-destructive examination (NDE) requirements. 20
7.8 Storage and shipping preparation . 22
7.9 Repair. 23
Annex A (normative) Environmental-service requirements. 24
Annex B (normative) Design-validation requirements . 26
Annex C (normative) Product-functional testing requirements . 30
Annex D (normative) Quality-control requirements. 33
Annex E (informative) Operating performance envelope . 35
Annex F (informative) Schematics of side-pocket mandrels . 38
Bibliography . 40

© ISO 2004 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 17078-1:2005
ISO 17078-1:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17078-1 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling and production
equipment.
ISO 17078 consists of the following parts, under the general title Petroleum and natural gas industries —
Drilling and production equipment:
 Part 1: Side-pocket mandrels
The following parts are under preparation:
 Part 2: Side-pocket mandrel gas lift valve and flow control devices
 Part 3: Latches, seals, and interface data for side-pocket mandrels and flow control devices
iv © ISO 2004 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 17078-1:2005
ISO 17078-1:2004(E)
Introduction
This part of ISO 17078 has been developed by users/purchasers and suppliers/manufacturers of side-pocket
mandrel products intended for use in the worldwide petroleum and natural gas industry. This part of
ISO 17078 is intended to provide requirements and information to all parties who are involved in the
specification, selection, manufacture, testing and use of side-pocket mandrel products. Further, this part of
ISO 17078 addresses supplier/manufacturer requirements that set the minimum parameters with which each
supplier/manufacturer shall comply, in order to be able to claim conformity with this part of ISO 17078.
This has been structured to allow different quality control grades to support quality control, design-validation,
design-verification, and product-functional testing. These variations allow the user/purchaser to select the
grades that are required for a specific application. If the user/purchaser does not specify a specific grade for
the following categories, the supplier/manufacturer will meet the requirements of grade 3.
Well environmental service classes. There are four environmental service classes for side-pocket mandrel
products that provide the user/purchaser with a range of choices to select products to meet varying
environmental conditions.
Design-validation grades. There are three design validation grades for side-pocket mandrel products that
provide the user/purchaser with a range of technical and performance requirements. Users of this part of
ISO 17078 should be aware that requirements in addition to those outlined herein might be needed for
individual applications. This part of ISO 17078 is not intended to inhibit a supplier/manufacturer from offering,
or the user/purchaser from accepting, alternative equipment or engineering solutions. Where an alternative is
offered, the supplier/manufacturer should identify any variations from this part of ISO 17078 and provide
details.
Product-functional testing grades. There are three product functional testing grades for side-pocket
mandrel products that provide the user/purchaser with a range of choices for validating that individual
products manufactured under this part of ISO 17078 meet the design specifications.
Quality-control grades. There are three quality-control grades that provide the user/purchaser with varying
grades of quality control requirements to meet specific preferences or applications. Additional quality
upgrades can be specified by the user/purchaser as supplemental requirements.
Annexes A, B, C and D of this part of ISO 17078 are normative requirements; Annexes E and F are
informative.

© ISO 2004 – All rights reserved v

---------------------- Page: 9 ----------------------

SIST EN ISO 17078-1:2005

---------------------- Page: 10 ----------------------

SIST EN ISO 17078-1:2005
INTERNATIONAL STANDARD ISO 17078-1:2004(E)

Petroleum and natural gas industries — Drilling and production
equipment —
Part 1:
Side-pocket mandrels
1 Scope
This part of ISO 17078 provides requirements for side-pocket mandrels used in the petroleum and natural gas
industry. This part of ISO 17078 includes specifying, selecting, designing, manufacturing, quality control,
testing, and preparation for shipping of side-pocket mandrels.
This part of ISO 17078 does not address nor include requirements for end connections between the side-
pocket mandrels and the well conduit. The installation and retrieval of side-pocket mandrels is outside the
scope of this part of ISO 17078. Additionally, this part of ISO 17078 does not include specifications for centre-
set mandrels, or mandrels that employ or support tubing-retrievable flow control devices.
This part of ISO 17078 does not include gas-lift or any other flow-control valves or devices, latches, and/or
associated wire line equipment that can or cannot be covered in other ISO specifications.
The side-pocket mandrels to which this part of ISO 17078 refers are independent devices that can accept
installation of flow-control or other devices down-hole.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method
ISO 6508-1, Metallic materials — Rockwell hardness test — Part 1: Test method (Scales A, B, C, D, E, F, G,
H, K, N, T)
ISO 6892, Metallic materials — Tensile testing at ambient temperature
ISO 9000:2000, Quality management systems — Fundamentals and vocabulary
ISO 9712, Non-destructive testing — Qualification and certification of personnel
ISO 11960:2001, Petroleum and natural gas industries — Steel pipes for use as casing or tubing for wells
ISO 15156-1, Petroleum and natural gas industries — Materials for use in H S-containing environments in oil
2
and gas production — Part 1: General principles for selection of cracking-resistant materials
ISO 15156-2, Petroleum and natural gas industries — Materials for use in H S-containing environments in oil
2
and gas production — Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons
© ISO 2004 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 17078-1:2005
ISO 17078-1:2004(E)
ISO 15156-3, Petroleum and natural gas industries — Materials for use in H S-containing environments in oil
2
and gas production — Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
1)
ANSI/NCSL Z540-1, Calibration Laboratories and Measuring and Test Equipment General Requirements
2)
ASME Boiler and Pressure Vessel Code, Section V, Nondestructive Examination
ASME Boiler and Pressure Vessel Code, Section VIII, Pressure Vessels, Division 1, Rules for Construction of
Pressure Vessels
ASME Boiler and Pressure Vessel Code, Section IX, Welding and Brazing Qualifications
3)
ASTM E94, Standard Guide for Radiographic Examination
ASTM E140, Standard Hardness Conversion Tables for Metals
ASTM E165, Standard Test Method for Liquid Penetrant Examination
ASTM E709, Standard Guide for Magnetic Particle Examination
4)
BS 2M 54:1991, Specification for temperature control in the heat treatment of metals
5)
SAE AMS-H-6875:1998, Heat Treatment of Steel Raw Materials
3 Terms and definitions
For the purpose of this document, the terms and definitions given in ISO 9000:2000 and the following apply.
3.1
acceptance
agreement/acknowledgement that side-pocket mandrel component(s) and/or assembly(ies) can be used
without restriction
3.2
certificate of conformance
documentation declaring that a specific side-pocket mandrel meets the requirements of this part of ISO 17078
and the requirements of the functional specification
3.3
coating
internal and/or external application of a material to a side-pocket mandrel for corrosion protection, paraffin
control, etc.
3.4
compressive load
force creating compression that may be applied to a side-pocket mandrel

1) NCSL International, 2995 Wilderness Place, Suite 107, Boulder, Colorado 80301-5404, USA.
2) American Society of Mechanical Engineers, Three Park Avenue, New York, NY 10016-5990, USA.
3) ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, USA.
4) British Standards Institute, Customer Services, 389 Chiswick High Road, London W4 4AL, UK.
5) SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA.
2 © ISO 2004 – All rights reserved

---------------------- Page: 12 ----------------------

SIST EN ISO 17078-1:2005
ISO 17078-1:2004(E)
3.5
date of manufacture
date of manufacturer's final acceptance of finished products
NOTE The date is expressed as “day-month-year” in the format DD-MM-YYYY.
3.6
deflector
internal device that guards landed side-pocket devices or discriminates the landing of side-pocket devices into
the side-pocket mandrel pocket (receptacle for mandrel devices), but deflects non-side-pocket devices, thus
allowing the latter to pass through the side-pocket mandrel, when being deployed down hole
3.7
design family
group of products whose configurations, sizes, materials and applications are sufficiently similar that identical
design methodologies can be used to establish the design parameters for each product within the family
3.8
design method
method, procedure or equations used by the supplier/manufacturer to design a side-pocket mandrel product
3.9
design validation
process of proving a design by testing to demonstrate conformity of the product to design requirements
[ISO/TS 29001:2003]
NOTE See also 5.7.
3.10
design verification
process of examining the result of a given design or development activity to determine conformity with
specified requirements
[ISO/TS 29001:2003]
3.11
dogleg
change in well bore inclination
NOTE The “severity” of the dogleg is proportional to the change in inclination, typically measured in degrees.
3.12
drift outside diameter
tube's ID through which all elements of the assembled side-pocket mandrel can pass
3.13
end connection
thread(s) on the side-pocket mandrel end(s) used to attach the side-pocket mandrel to the tubing string
3.14
environmental service class
category of environmental conditions for which the side-pocket mandrel product is designed to be used
NOTE See also 5.6.
3.15
external drifting
test to observe the unencumbered or unrestricted passage of a side-pocket mandrel having a specific
diameter through a drift test tool of specified inside diameter and length
© ISO 2004 – All rights reserved 3

---------------------- Page: 13 ----------------------

SIST EN ISO 17078-1:2005
ISO 17078-1:2004(E)
3.16
external test pressure
differential pressure between the applied external pressure and internal pressure at which a side-pocket
mandrel is tested for collapse resistance
3.17
full life cycle
expected period of time in which the product shall function according to manufacturer’s specifications
3.18
functionality
capability of a side-pocket mandrel to conform to defined properties, characteristics and limits
3.19
gas passage undercut
clearance between the flow-control device and the pocket of the side-pocket mandrel through which injected
media flow
3.20
heat
material originating from a final melt or cast lot
NOTE For re-melted alloys, the heat is the raw material originating from a single re-melted ingot.
3.21
internal drifting
test to observe the unencumbered or unrestricted passage of a drift bar having a specific diameter and length
through a side-pocket mandrel to determine its full-bore capability
3.22
internal test pressure
differential pressure between the applied internal pressure and external pressure at which a side-pocket
mandrel is tested for burst resistance
3.23
job lot
group or quantity of piece parts, sub-assemblies or assemblies that are grouped or processed together during
the manufacturing process
3.24
latch
retention mechanism for a flow-control device that is landed in the side-pocket mandrel
3.25
latch profile
feature such as a lug or recess that is suitable for the reception of the locking mechanism within a side-pocket
mandrel
3.26
linear indication
material inconsistency whose length is equal to or greater than three times the width of the material
inconsistency
3.27
linear mass
mass per length of tubular product
4 © ISO 2004 – All rights reserved

---------------------- Page: 14 ----------------------

SIST EN ISO 17078-1:2005
ISO 17078-1:2004(E)
3.28
manufacturing
process(es) and action(s) performed by an equipment supplier/manufacturer that are necessary to provide
finished component(s), assemblies, and related documentation that fulfil the requests of the user/purchaser
and that meet the standards of the supplier/manufacturer
NOTE Manufacturing begins when the supplier/manufacturer receives the order and is completed at the moment the
component(s), assembly(ies), and related documentation are transferred to a transportation provider.
3.29
model
side-pocket mandrels with unique components and functional characteristics that differentiate it from other
side-pocket mandrels of the same type
NOTE Side-pocket mandrels can have a variety of end connections.
3.30
operating environment
set of environmental conditions to which the product is exposed during its service life
NOTE Environmental conditions can include temperature, pressure, liquid composition and properties, gas
composition and properties, solids, etc.
3.31
operational parameter
requirement and/or restriction that the product is exposed to during its service life
EXAMPLES Operating environment, through-tubing drift, landing and retrieval of flow-control devices, passage of
various tools through the side-pocket mandrel, injection of various well treatment chemicals/fluids, etc.
3.32
orienting profile
design feature (e.g. orienting sleeve) of a side-pocket mandrel that acts together with certain wireline tools to
aid in radial and vertical alignment of tools used to install and remove side-pocket landed equipment
3.33
perceptible leak
any leak during a hydro test that can be observed
3.34
pocket
parallel bore, including sealing surfaces and latching profiles, that is offset from and essentially parallel with
the through-bore of the side-pocket mandrel
3.35
product functional-testing grade
category based on a defined range of processes, method(s) and/or test(s) that are used by the
supplier/manufacturer to demonstrate that a particular side-pocket mandrel has been manufactured to fully
meet the functional and manufacturing requirements for that product
3.36
quality-control grade
category based on a defined range of processes and/or method(s) that are used by the supplier/manufacturer
to assure the quality of the materials and manufacturing process(es) used to produce a particular side-pocket
mandrel
3.37
rated pressure
maximum differential pressure, at the rated temperature, to which the side-pocket mandrel is designed to be
subjected in normal operation
© ISO 2004 – All rights reserved 5

---------------------- Page: 15 ----------------------

SIST EN ISO 17078-1:2005
ISO 17078-1:2004(E)
3.38
rated temperature
maximum temperature, at the rated pressure, to which the mandrel is designed to be subjected in normal
operation in a well
3.39
rounded indication
material inconsistency that is circular or elliptical in shape, such that the length of the material inconsistency is
less than three times its width
3.40
side-pocket mandrel
tubing-mounted device that accepts a flow-control or other device in a bore that is offset from and essentially
parallel with the through-bore of the tubing product
NOTE This parallel bore includes sealing surfaces and latching profiles.
3.41
special-service side-pocket mandrel
side-pocket mandrel designed for special operations including chemical injection, CO injection, hydraulic
2
control, electrical control, or other applications where a secondary conduit terminates at the side-pocket
mandrel
3.42
supplier/manufacturer
company, organization or entity that designs, man
...