Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls (IEC 60730-2-9:2008, modified)

This part of IEC 60730 applies to automatic electrical temperature sensing controls for use in, on or in association with equipment for household and similar use, including electrical controls for heating, air-conditioning and similar applications. The equipment may use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof.

Automatische elektrische Regel- und Steuergeräte für den Hausgebrauch und ähnliche Anwendungen - Teil 2-9: Besondere Anforderungen an temperaturabhängige Regel- und Steuergeräte (IEC 60730-2-9:2008, modifiziert)

Dispositifs de commande électrique automatiques à usage domestique et analogue - Partie 2-9: Règles particulières pour les dispositifs de commande thermosensibles (CEI 60730-2-9:2008, modifiée)

La CEI 60730-2-9:2008 s'applique aux dispositifs de commande électrique automatiques thermosensibles pour usage dans, sur ou en association avec des appareils à usage domestique et analogue, y compris les dispositifs de commande électrique pour le chauffage, le conditionnement d'air et applications analogues. Le matériel peut fonctionner à l'électricité, au gaz, au pétrole, aux combustibles solides, à l'énergie solaire, etc., ou à une de leurs combinaisons. Cette troisième édition annule et remplace la seconde édition publiée en 2000 et ses Amendement 1 (2002) et Amendement 2 (2004), et constitue une révision technique. Cette édition de la CEI 60730-2-9 comprend une nouvelle Annexe EE, qui est un guide informatif pour l'application des dispositifs de commande thermosensibles. De plus, une nouvelle exigence en 17.3.1 a été ajoutée pour traiter de l'exigence d'endurance pour les dispositifs thermosensibles dans lesquels la totalité du dispositif de commande est déclarée comme élément sensible pour des températures de fonctionnement inférieures à 0 °C. Ce document contient également quelques modifications éditoriales dues aux nouvelles éditions des normes référencées. La présente Partie 2-9 doit être utilisée conjointement avec la CEI 60730-1. Elle a été établie sur la base de la troisième édition de cette norme (1999) et de ses Amendement 1 (2003) et Amendement 2 (2007). Les éditions futures de la CEI 60730-1, ou ses amendements, pourront être pris en considération.

Avtomatske električne krmilne naprave za uporabo v gospodinjstvu in za podobno uporabo - 2-9. del: Posebne zahteve za temperaturne regulatorje (IEC 60730-2-9:2008, spremenjen)

Ta del IEC 60730 velja za avtomatske temperaturne regulatorje za uporabo v gospodinjstvu ali v povezavi z opremo za gospodinjstvo in podobno uporabo, vključno z električnimi krmilnimi napravami za gretje, klimatiziranje in podobne uporabe. Oprema lahko uporablja elektriko, plin, olje, trdno gorivo, solarno termalno energijo itd. ali njihove kombinacije.

General Information

Status
Withdrawn
Publication Date
06-Dec-2010
Withdrawal Date
07-Mar-2022
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
08-Mar-2022
Due Date
31-Mar-2022
Completion Date
08-Mar-2022

Relations

Buy Standard

Standard
EN 60730-2-9:2011
English language
68 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60730-2-9:2011
01-januar-2011
1DGRPHãþD
SIST EN 60730-2-9:2002
SIST EN 60730-2-9:2002/A1:2004
SIST EN 60730-2-9:2002/A11:2003
SIST EN 60730-2-9:2002/A12:2005
SIST EN 60730-2-9:2002/A2:2005
$YWRPDWVNHHOHNWULþQHNUPLOQHQDSUDYH]DXSRUDERYJRVSRGLQMVWYXLQ]DSRGREQR
XSRUDERGHO3RVHEQH]DKWHYH]DWHPSHUDWXUQHUHJXODWRUMH ,(&
VSUHPHQMHQ
Automatic electrical controls for household and similar use - Part 2-9: Particular
requirements for temperature sensing controls (IEC 60730-2-9:2008, modified)
Automatische elektrische Regel- und Steuergeräte für den Hausgebrauch und ähnliche
Anwendungen - Teil 2-9: Besondere Anforderungen an temperaturabhängige Regel- und
Steuergeräte (IEC 60730-2-9:2008, modifiziert)
Dispositifs de commande électrique automatiques à usage domestique et analogue -
Partie 2-9: Règles particulières pour les dispositifs de commande thermosensibles (CEI
60730-2-9:2008, modifiée)
Ta slovenski standard je istoveten z: EN 60730-2-9:2010
ICS:
97.120 Avtomatske krmilne naprave Automatic controls for
za dom household use
SIST EN 60730-2-9:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60730-2-9:2011

---------------------- Page: 2 ----------------------

SIST EN 60730-2-9:2011

EUROPEAN STANDARD
EN 60730-2-9

NORME EUROPÉENNE
November 2010
EUROPÄISCHE NORM

ICS 97.120 Supersedes EN 60730-2-9:2002 + A1:2003 + A2:2005 + A11:2003 + A12:2004


English version


Automatic electrical controls for household and similar use -
Part 2-9: Particular requirements for temperature sensing controls
(IEC 60730-2-9:2008, modified)


Dispositifs de commande électrique Automatische elektrische Regel- und
automatiques à usage domestique et Steuergeräte für den Hausgebrauch und
analogue - ähnliche Anwendungen -
Partie 2-9: Règles particulières pour les Teil 2-9: Besondere Anforderungen an
dispositifs de commande thermosensibles temperaturabhängige Regel- und
(CEI 60730-2-9:2008, modifiée) Steuergeräte
(IEC 60730-2-9:2008, modifiziert)




This European Standard was approved by CENELEC on 2010-11-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60730-2-9:2010 E

---------------------- Page: 3 ----------------------

– 2 –             60730-2-9/FDIS IEC
SIST EN 60730-2-9:2011
EN 60730-2-9:2010 – 2 –
Foreword
The text of the International Standard IEC 60730-2-9:2008, prepared by IEC TC 72, Automatic controls
for household use, together with the common modifications prepared by the Technical Committee
CENELEC TC 72, Automatic controls for household use, was submitted to the CENELEC Unique
Acceptance Procedure.
A draft amendment was prepared by the Technical Committee CENELEC TC 72, Automatic controls
for household use. It was submitted to the Unique Acceptance Procedure.
The combined texts were approved by CENELEC as EN 60730-2-9 on 2010-11-01.
This document supersedes EN 60730-2-9:2002 + A1:2003 + A2:2005 + A11:2003 + A12:2004.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-11-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-11-01
This Part 2-9 is to be used in conjunction with EN 60730-1:2000, Automatic electrical controls for
household and similar use – Part 1: General requirements, and any subsequent amendments.
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and covers essential requirements of
EC Directive 2004/108/EC. See Annex ZZ.
Annexes ZA and ZZ have been added by CENELEC.
__________

---------------------- Page: 4 ----------------------

60730-2-9 IEC:2008                – 3 –
SIST EN 60730-2-9:2011
– 3 – EN 60730-2-9:2010
Endorsement notice
The text of the International Standard IEC 60730-2-9:2008 was approved by CENELEC as a European
Standard with agreed common modifications as given below.
COMMON MODIFICATIONS
1 1 Scope and normative references
1.5 Normative references
Add the following as the first reference:
EN 60216-1, Electrical insulating materials – Properties of thermal endurance – Part 1: Ageing
procedures and evaluation of test results (IEC 60216-1)
2 2 Definitions
Add the following definition:
2.2.101.2
non-bimetallic single operation device
single operation device having a temperature sensing element which is part of a combination action
control, the operation of which cannot be separated from other functions of the control and having a
non-bimetallic thermal element that operates only once and then requires complete or partial
replacement
NOTE 1 When such parts can be tested separately, they are considered to be thermal links within the scope of EN 60691.
NOTE 2 The ageing period and thermal response of the device is dependent on the intended use of the device. As a result,
the nature of the testing applicable to the device should be representative of the application conditions for which the protective
control is intended (see 7.2).
NOTE 3 Non-bimetallic single operation devices provide the equivalent of micro-disconnection.
2.2.101.2.2 Delete this definition.
2.2.101.2.3 Delete this definition.
4 General notes on test
4.1.101 Delete the note.
4.2.1 Addition:
Replace the text with:
Six samples of bimetallic SODs are used for the test of Clause 15 and a further six for the test of
Clause 17.
6 Classification
6.4.3.105 Replace with:
– an action which cannot be reset under electrically loaded conditions and at temperatures above
-20 °C or at a lower temperature if so declared (Type 1.AK or 2.AK);
6.7 According to ambient temperature limits of the switch head

---------------------- Page: 5 ----------------------

– 4 –             60730-2-9/FDIS IEC
SIST EN 60730-2-9:2011
EN 60730-2-9:2010 – 4 –
Add the following subclause:
6.7.104 Non-bimetallic SOD for incorporation into appliances for heating or employing liquids or
steam.
NOTE Not suitable for use in instantaneous water heaters.
7 Information
7.2 Methods of providing information
Table 7.2
Replace requirements for 103, 115 and 116 as follows:
Clause or Method
Information
subclause
103 SOD reset temperature (either –35 °C or 0 °C) (17.15.2.2) 2.2.101 X
11.4.103
17.15.2.2
106
115 Ageing temperature for non-bimetallic SOD 17.15.2.2.1 D
17.15.2.2.2
107
116 Rate of rise of temperature for testing non-bimetallic SOD 17.15.2.2.1 D

17.15.2.2.2
Add the following new item to Table 7.2.
601 The minimum voltage at which a voltage maintained 11.4.106
thermal cut-out will not reset (this shall not be higher
than 0,85 times the minimum rated voltage).
In the additional notes replace Note 102 with:
102)
Controls using liquid metal are allowed only with a special marking on the control. Documentation (D) shall contain a
clear warning of the actual danger that may occur. The following symbol shall be used for marking the control:

Add the following additional notes at the bottom of the table:
106)
Determined by the control manufacturer based on the opening temperature of the thermal-cut out.
107)
Determined by the control manufacturer referring to the actual maximum rate of rise probable in the
projected end-use equipment.

11 Constructional requirements
11.1.102 Add the following at the end of the first sentence:
Insulating material used in non-bimetallic SODs as defined in this standard shall comply with the
requirements of EN 60216-1:2001 and be suitable for the application.

---------------------- Page: 6 ----------------------

60730-2-9 IEC:2008                – 5 –
SIST EN 60730-2-9:2011
– 5 – EN 60730-2-9:2010
11.4.3.101 Delete the note.
11.4.101 Delete the note.
11.4.106
Replace the title and the text of this clause by the following:
11.4.106 Voltage maintained thermal cut-out (Type 1.AK or Type 2.AK)
A voltage maintained thermal cut-out shall be so designed that it does not automatically reset at any
temperature higher than -20 °C or any lower temperature declared in Table 7.2, Requirement 111.
Compliance is checked by the following test which is carried out as part of 17.14:
The voltage maintained thermal cut-out shall be maintained, in an operated condition, at - 20 °C or at
any lower temperature declared by the manufacturer in Table 7.2, Requirement 111.
The voltage maintained thermal cut-out is connected to the voltage value declared in Table 7.2,
Requirement 601, in series with a resistance of a value which will limit the current through the control to
not more than the maximum rated current together with a suitable means to detect resetting of the
thermal cut-out.
The test will continue for 1 h. The device shall not reset during this period.
11.101 Time factor
Delete the note.
12 Moisture and dust resistance
12.101.3 Delete the note.
13 Electric strength and insulation resistance
Replace the entire text with:
This clause of Part 1 is applicable.
15 Manufacturing deviation and drift
15.5.3.109 Replace the subclause as follows:
15.5.3.109 For SODs, after the contacts have operated, satisfactory disconnection is determined by
subjecting each SOD device to the voltage specified in Table 13.2, with no prior humidity treatment.
16 Environmental stress
Addition:
Replace the additional subclause as follows:

---------------------- Page: 7 ----------------------

– 6 –             60730-2-9/FDIS IEC
SIST EN 60730-2-9:2011
EN 60730-2-9:2010 – 6 –
All controls except bimetallic SODs shall be environmentally conditioned as per Clause 16 of
EN 60730-1.
17 Endurance
17.8.4 Additional subclause:
17.8.4.101 Delete the note.
17.15.1.3
Replace the first sentence of the clause by the following:
For bimetallic single operation devices with a declared reset temperature of - 35 °C, six untested
samples shall be subjected to an over-voltage test for one cycle under the electrical conditions of
Table 17.2-1.
17.15.1.3.1
Replace the first sentence of the clause by the following:
For bimetallic single operation devices with a declared reset temperature of 0 °C, one sample shall be
subjected to an over-voltage test of 50 cycles under the electrical conditions of Table 17.2-1.
17.15.2 Replace the subclause as follows:
17.15.2 Non-bimetallic single operation devices
Non-bimetallic Single Operation Devices are subject to the following tests:
For a non-bimetallic SOD, automatic temperature sensing functions except those for the non-bimetallic
part of the control, such as thermostat, temperature limiter and/or the thermal-cut-out, shall comply
with 17.16.101, 17.16.103 and 17.16.104 respectively.
These tests are conducted on separate samples.
The apparatus used for the tests of 17.15.2.1 and 17.15.2.2 shall be constructed so that heat can be
applied to the thermal sensing element of the single operation device whilst taking care that other parts
of the control are protected from exposure to temperatures in excess of their intended use.
17.15.2.1 Six untested samples are then to be mounted in a suitable apparatus and the thermal
sensing elements are conditioned for an ageing period equal to either 750 h or the result of the
specified number of cycles declared by the end product application divided by 4 (calculation value is
the number of hours), whichever is greater. The ageing temperature is declared in Table 7.2, Item 115,
tolerance of 0 K -5 K. No operation of the single operation devices shall occur during this ageing
period. Operation of the devices shall be detected as indicated in 15.5.3.107.
17.15.2.2 At the end of the ageing period, the samples are removed from the apparatus.
The appropriate tests of Clause 15 shall be repeated on six untested samples and the six samples
subjected to the conditioning of 17.15.2.1 and the temperatures measured shall be within the declared
deviation limits, with the electrical conditions of the test V and I .
Rmax Rmax
For non-bimetallic SOD's where any sensing element has a declared reset temperature, the SOD's
shall be held at the temperature declared in Table 7.2, the test shall continue for 7 h. The device shall
not reset during this period as determined as indicated in 15.5.3.109.
All samples shall then be subjected to the test of Clause 13, carried out at the temperature limits
declared in Table 7.2, Requirement 36.

---------------------- Page: 8 ----------------------

60730-2-9 IEC:2008                – 7 –
SIST EN 60730-2-9:2011
– 7 – EN 60730-2-9:2010
NOTE: The apparatus used for the tests of 17.15.2.1 and 17.15.2.2 shall be constructed so that heat can be applied to the
thermal sensing element of the SOD whilst taking care that other parts of the control are protected from exposure to
temperatures in excess of their intended use.
17.16.101 Delete the „in Canada and the USA‟ note and the following related subclauses: 17.16.102,
17.16.102.1, 17.16.102.2 and 17.16.102.3.
17.16.105 Replace this subclause by “Void”.
18 Mechanical strength
18.102.3 Delete the note.
23 Electromagnetic compatibility (EMC) requirements – emission
23.101 Delete the note:
Annex H Requirements for electronic controls
H.26.10 Replace „Ring wave test‟ by “Void”.
H.26.10.5 Replace the addition by “Void”.
Annex AA Maximum manufacturing deviation and drift
Delete the note „In Canada and the USA, Annex AA is normative.‟
Annex CC Number of cycles
Delete Table CC.2.
Annex DD Controls for use in agricultural confinement buildings
DD.9.2 Delete the note.
Annex EE Guide to the application of temperature sensing controls within the scope
of IEC 60730-2-9
EE.3.6 Delete the note „In Canada and the USA, flying leads are allowed.

---------------------- Page: 9 ----------------------

– 8 –             60730-2-9/FDIS IEC
SIST EN 60730-2-9:2011
EN 60730-2-9:2010 – 8 –
Add the following annexes.
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60216-1 - Electrical insulating materials - EN 60216-1 -
Properties of thermal endurance -
Part 1: Ageing procedures and evaluation of test
results

IEC 60335 series Household and similar electrical appliances - EN 60335 series
Safety
IEC 60691 2002 Thermal-links - Requirements and application EN 60691 2003
+ A1 2006 guide + A1 2007
IEC 60730-2-4 Automatic electrical controls for household and EN 60730-2-4
- -
similar use -
Part 2-4: Particular requirements for thermal
motor protectors for motor-compressors of
hermetic and semi-hermetic type

---------------------- Page: 10 ----------------------

60730-2-9 IEC:2008                – 9 –
SIST EN 60730-2-9:2011
– 9 – EN 60730-2-9:2010
Annex ZZ
(informative)

Coverage of Essential Requirements of EC Directives
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant essential requirements as given in Article 1 of Annex I of the EC Directive EMC (2004/108/EC).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling
within the scope of this standard.

---------------------- Page: 11 ----------------------

SIST EN 60730-2-9:2011

---------------------- Page: 12 ----------------------

SIST EN 60730-2-9:2011
IEC 60730-2-9
Edition 3.0 2008-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Automatic electrical controls for household and similar use –
Part 2-9: Particular requirements for temperature sensing controls

Dispositifs de commande électrique automatiques à usage domestique et
analogue –
Partie 2-9: Règles particulières pour les dispositifs de commande
thermosensibles

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
XB
CODE PRIX
ICS 97.120 ISBN 2-8318-9840-4

---------------------- Page: 13 ----------------------

SIST EN 60730-2-9:2011
– 2 – 60730-2-9 © IEC:2008
CONTENTS
FOREWORD.4
1 Scope and normative references.7
2 Definitions .8
3 General requirements .10
4 General notes on tests.10
5 Rating.10
6 Classification .10
7 Information .11
8 Protection against electric shock.13
9 Provision for protective earthing.13
10 Terminals and terminations.13
11 Constructional requirements .13
12 Moisture and dust resistance .16
13 Electric strength and insulation resistance.17
14 Heating.17
15 Manufacturing deviation and drift .18
16 Environmental stress .19
17 Endurance .19
18 Mechanical strength.24
19 Threaded parts and connections .25
20 Creepage distances, clearances and distances through solid insulation.25
21 Fire hazard testing.25
22 Resistance to corrosion .25
23 Electromagnetic compatibility (EMC) requirements – emission .26
24 Components .26
25 Normal operation .26
26 Electromagnetic compatibility (EMC) requirements – immunity .26
27 Abnormal operation.27
28 Guidance on the use of electronic disconnection .27
Annexes.28
Annex H (normative) Requirements for electronic controls .28
Annex J (normative) Requirements for controls using thermistors .33
Annex AA (informative) Maximum manufacturing deviation and drift.34
Annex BB (informative) Time factor.35
Annex CC (informative) Number of cycles .38
Annex DD (normative) Controls for use in agricultural confinement buildings .39
Annex EE (informative) Guide to the application of temperature sensing controls within
the scope of IEC 60730-2-9.43

Figure 11.4.13.102 – Impact tool .14
Figure 17.101.3 – Aluminium cylinder for temperature change method.23

---------------------- Page: 14 ----------------------

SIST EN 60730-2-9:2011
60730-2-9 © IEC:2008 – 3 –
Figure BB.1 – Determination of time factor in the case of a sudden temperature change.36
Figure BB.2 – Determination of time factor in the case of a linear rise of test-bath
temperature .37
Figure EE.1 – Thermostat .52
Figure EE.2 – Self-resetting temperature limiter.53
Figure EE.3 – Non-self-resetting temperature limiter.53
Figure EE.4 – Self-resetting thermal cut-out .55
Figure EE.5 – Manual reset thermal cut-out .55
Figure EE.6 – Single operation device .57
Figure EE.7 – Three-stage control system .58

Table H.26.2.101 – Compliance criteria .30
Table BB.1 – Method to determine and verify time factor values (see 11.101) .37
Table EE.1 – Typical examples of the classification of temperature sensing controls in
accordance with IEC 60730-2-9.59

---------------------- Page: 15 ----------------------

SIST EN 60730-2-9:2011
– 4 – 60730-2-9 © IEC:2008
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

AUTOMATIC ELECTRICAL CONTROLS
FOR HOUSEHOLD AND SIMILAR USE –

Part 2-9: Particular requirements
for temperature sensing controls


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60730-2-9 has been prepared by IEC technical committee 72:
Automatic controls for household use.
This third edition cancels and replaces the second edition published in 2000, its Amendment 1
(2002) and Amendment 2 (2004) and constitutes a technical revision.
This edition of IEC 60730-2-9 contains a new Annex EE, which is an informative guide to the
application of temperature sensing controls. Additionally, a new requirement to 17.3.1 (there is
an error in the FDIS document - 17.7.3 should be 17.3.1) was added to address the endurance
requirement for temperature sensing devices where the whole control is declared as the
o
sensing element for ambient temperatures below 0 C. This document contains also some
editorial changes due to new editions of referenced standards.

---------------------- Page: 16 ----------------------

SIST EN 60730-2-9:2011
60730-2-9 © IEC:2008 – 5 –
The text of this standard is based on the following documents:
FDIS Report on voting
72/763/FDIS 72/767/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with ISO/IEC Directives, Part 2.
This Part 2-9 is intended to be used in conjunction wit
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.