SIST EN 13479:2005
(Main)Welding consumables - General product standard for filler metals and fluxes for fusion welding of metallic materials
Welding consumables - General product standard for filler metals and fluxes for fusion welding of metallic materials
This document specifies general delivery conditions for filler metals and fluxes for fusion welding of metallic materials. This document does not apply to auxiliaries such as shielding gases. This document is intended for application in a number of situations:
- The manufacturer should use this document to establish the product's characteristics.
- This document may be used for contractual purposes, as a reference document.
- This document should also be used as a reference document for product conformity assessment.
Schweißzusätze - Allgemeine Produktnorm für Zusätze und Pulver zum Schmelzschweißen von metallischen Werkstoffen
Dieses Dokument legt allgemeine Lieferbedingungen für Zusätze und Pulver für das Schmelzschweißen
metallischer Werkstoffe fest. Dieses Dokument gilt nicht für Hilfsstoffe wie Schutzgase. Dieses Dokument ist
für eine Reihe unterschiedlicher Anwendungsfälle vorgesehen:
.der Hersteller sollte dieses Dokument zur Festlegung der Produktmerkmale verwenden;
.dieses Dokument darf als Referenzdokument für vertragliche Zwecke eingesetzt werden;
.dieses Dokument sollte auch als Referenzdokument zur Konformitätsbewertung verwendet werden.
Produits consommables pour le soudage - Norme produit générale pour les métaux d'apport et les flux pour le soudage par fusion de matériaux métalliques
Le présent document spécifie les conditions générales de livraison relatives aux métaux d?apport et aux flux
destinés au soudage par fusion des matériaux métalliques. Le présent document ne s?applique pas aux
produits auxiliaires tels que les gaz de protection. Le présent document est destiné a etre appliqué dans un
certain nombre de cas :
.il convient que le fabricant utilise le présent document pour établir les caractéristiques du produit ;
.le présent document peut etre utilisé pour des raisons contractuelles, en tant que document de
référence ;
.il convient que le présent document soit également utilisé en tant que document de référence dans le cas
d?une évaluation de conformité du produit.
Dodajni materiali za varjenje - Splošni produktni standard za dodajne materiale in praške za talilno varjenje kovinskih materialov
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Welding consumables - General product standard for filler metals and fluxes for fusion welding of metallic materialsDodajni materiali za varjenje - Splošni produktni standard za dodajne materiale in praške za talilno varjenje kovinskih materialovProduits consommables pour le soudage - Norme produit générale pour les métaux d'apport et les flux pour le soudage par fusion de matériaux métalliquesSchweißzusätze - Allgemeine Produktnorm für Zusätze und Pulver zum Schmelzschweißen von metallischen Werkstoffen25.160.20Potrošni material pri varjenjuWelding consumablesICS:SIST EN 13479:2005enTa slovenski standard je istoveten z:EN 13479:200401-marec-2005SIST EN 13479:2005SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13479December 2004ICS 25.160.20English versionWelding consumables - General product standard for fillermetals and fluxes for fusion welding of metallic materialsProduits consommables pour le soudage - Norme produitgénérale pour les métaux d'apport et les flux pour lesoudage par fusion de matériaux métalliquesSchweißzusätze - Allgemeine Produktnorm für Zusätze undPulver zum Schmelzschweißen von metallischenWerkstoffenThis European Standard was approved by CEN on 12 November 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13479:2004: E
EN 13479:2004 (E) 2 Contents
Page Foreword.3 1 Scope.5 2 Normative references.5 3 Terms and definitions.5 4 Manufacturing process.6 5 Requirements.6 6 Testing, assessment and sampling methods.7 7 Evaluation of conformity.7 8 Marking, labelling, packaging.9 Bibliography.16
EN 13479:2004 (E) 3 Foreword This document (EN 13479:2004) has been prepared by Technical Committee CEN/TC 121 “Welding”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 13479:2004 (E) 4
Introduction This document is part of a family comprising the following:
Quality management system EN ISO 9001 Quality requirements for consumables EN 12074 Product standard for consumables EN 13479 Technical delivery condition standard EN ISO 544 EN 440 EN 499 EN 757 EN 758 EN 760 EN 1599 EN . Consumable classification standards Standards for test methods and quality requirements of consumables Testing of consumables, e.g. EN ISO 3690 Testing of the weld, e.g. EN 910 EN 14532-1 EN 14532-2 EN 14532-3
EN 13479:2004 (E) 5 1 Scope This document specifies general delivery conditions for filler metals and fluxes for fusion welding of metallic materials. This document does not apply to auxiliaries such as shielding gases. This document is intended for application in a number of situations: – The manufacturer should use this document to establish the product's characteristics. – This document may be used for contractual purposes, as a reference document. – This document should also be used as a reference document for product conformity assessment. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 760, Welding consumables — Fluxes for submerged arc welding — Classification EN 10204, Metallic products — Types of inspection documents EN 12074, Welding consumables — Quality requirements for manufacture, supply and distribution of consumables for welding and allied processes EN 14532-1:2004, Welding consumables — Test methods and quality requirements — Part 1: Primary methods and conformity assessment of consumables for steel, nickel and nickel alloys EN 14532-2, Welding consumables — Test methods and quality requirements — Part 2: Supplementary methods and conformity assessment of consumables for steel, nickel and nickel alloys EN 14532-3:2004, Welding consumables — Test methods and quality requirements — Part 3: Conformity assessment of wire electrodes, wires and rods for welding of aluminium alloys EN ISO 544, Welding consumables — Technical delivery conditions for welding filler materials — Type of product, dimensions, tolerances and markings (ISO 544:2003) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 product specification manufacturer's document which specifies requirements for a welding consumable including, as applicable, chemical composition and mechanical properties of deposited metal, coating type, flux composition, range of welding parameters, and the designation according to the appropriate classification standard 3.2 manufacturer party who has legal responsibility for the finished quality of the product placed upon the market 3.3 deposited metal filler metal that has been added during welding
EN 13479:2004 (E) 6 4 Manufacturing process The manufacturing processes used are at the discretion and responsibility of the manufacturer. 5 Requirements 5.1 General Products claiming compliance with this document shall meet the requirements of this Clause. 5.2 Product specification The product specification shall include the following information, as a minimum: – manufacturer's brand name for the consumable; – dimension; – technical delivery conditions in accordance with EN ISO 544; – description of the covering, flux or filling material in terms of those major constituents which define the characteristics of the consumable (e.g. oxides, carbonates, fluorides and metals); – classification of the consumable according to the relevant standard; – information to the user on the intended use in accordance with the welding consumable classification standard. 5.3 Dimensions and shape Tolerances on dimensions and shape shall be in accordance with EN ISO 544. 5.4 Mechanical properties The mechanical properties shall be in accordance with the specific requirements in the relevant welding consumable classification standards (see Introduction). In cases where the requirements for the specific property are not defined in the classification standard, the relevant sub-clause in EN 14532-1, EN 14532-2 or EN 14532-3 shall be used. Tests on butt welds are not required by this document, except in the case of consumables classified for single or two run welding technique. 5.5 Chemical composition Chemical composition shall be in accordance with the appropriate welding consumable classification standard. 5.6 Durability Deposited metals are deemed durable when the consumables comply with the requirements of this standard. 5.7 Dangerous substances Deposited metals shall not release any dangerous substances in excess of the maximum permitted levels specified in a relevant European Standard for the material or permitted in the national regulations of the member state of destination.
EN 13479:2004 (E) 7 6 Testing, assessment and sampling methods 6.1 Dimensions and shape Measurement of diameter shall be carried out with a micrometer screw gauge with a range of 0 to 10 mm and of length if applicable with a ruler, or other suitable apparatus. Five measurements shall be made within the smallest packaging unit taken at random from a batch, heat or lot. The accuracy shall be at least 0,01 mm for diameter measurement and 1 mm for length measurement. 6.2 Mechanical properties The mechanical properties shall be verified according to the specific requirements in the relevant welding consumable classification standards. In cases where the requirements for the specific property are not defined in the welding consumable classification standard, the relevant sub-clause in EN 14532-1, EN 14532-2 or EN 14532-3 shall be used. 6.3 Chemical composition Chemical analysis shall be carried out using appropriate established published methods. At least three determinations shall be made on each sample. The mean value shall meet the requirement. 7 Evaluation of conformity 7.1 General The compliance of the products with the requirements of this document shall be demonstrated by: – Initial type testing; – Factory production control by the manufacturer. 7.2 Initial type testing 7.2.1 General Initial type testing shall be performed to show conformity with this document. Tests previously performed in accordance with the provisions of this document (same product, same characteristic(s), test method, sampling procedure, system of attestation of conformity, etc.) may be taken into account. In addition, initial type testing shall be performed at the beginning of the production or at the beginning of a new method of production (where this may affect the stated properties). All characteristics in Clause 5 shall be subject to initial type testing, with the exception of release of dangerous substances, which can be assessed indirectly by controlling the content of the substance concerned. 7.2.2 Initial type test program The initial type testing programme shall be carried out in accordance with EN ISO 544 and, as relevant, in accordance with the welding consumable classification standard, EN 14532-1, EN 14532-2 or EN 14532-3. 7.2.3 Documentation The results of the initial test programme shall be recorded and kept in a technical file for a period of at least 5 years after the date when the last product to which the test programme refers to was delivered.
EN 13479:2004 (E) 8 7.2.4 Sampling Chemical analysis shall be performed on samples of the product, the stock from which it is made or a deposited metal according to the relevant welding consumable classification standard. Samples shall be taken and tested in accordance with a prescribed plan. The report of the testing shall be an inspection document in accordance with EN 10204, minimum Type 2.2. 7.3 Factory production control (FPC) 7.3.1 General The manufacturer shall establish, document and maintain an FPC system to ensure that the products placed on the market conform to the stated performance characteristics. The FPC system shall consist of procedures, regular inspections and tests and/or assessments and the use of the results to control raw and other incoming materials, the production process and the product. An FPC system conforming to the requirements of EN ISO 9001 and made specific to the requirements of this document, shall be considered to satisfy the requirements of this document. Corresponding Clauses from EN 12074 which place the same or more stringent conditions than EN ISO 9001 shall be considered to satisfy those corresponding Clauses from this document. The results of inspections, tests or assessments requiring action shall be recorded, as shall any action taken. The action to be taken when control values or criteria are not met shall be recorded and retained for the period specified in the manufacturer’s FPC procedures. The manufacturer shall es
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.