SIST EN 15061:2022
(Main)Safety of machinery - Safety requirements for strip processing line machinery and equipment
Safety of machinery - Safety requirements for strip processing line machinery and equipment
This European Standard defines the health and safety requirements of strip processing lines.
This European Standard deals with significant hazards, hazardous situations and events relevant for strip processing line machinery and equipment, when used as intended and under conditions foreseen by the manufacturer, but also includes foreseeable faults and malfunctions in case of misuse.
This European Standard applies to:
Strip processing lines for treating metal strip: from coil take-over-point of the entry section through the process up to the coil take-over-point of the exit section or interface to other lines (terminal equipment).
NOTE 1 The aforementioned lines/ processes can also occur in combination.
NOTE 2 If the aforementioned lines/processes are combined with processes which are not covered by the scope of this standard, it is recommended to use this standard as a guideline.
NOTE 3 Thermo process equipment integrated in strip processing lines is covered by EN 746 series. For dryers and ovens, in which flammable substances are released, EN 1539 applies.
This European Standard does not cover:
Thermo process equipment, e. g., in accordance with EN 746 series;
Dryers and ovens in accordance with EN 1539;
Coil transporting system before coil take-over-point at the entry section and after coil take-over-point at the exit section, e. g., hook conveyors, overhead cranes, fork lift and railway trucks and other vehicles;
Acid regeneration plants;
Regeneration plants which are not integral part of the strip processing line
Storage equipment for coils;
Rolling mill stands (i. e., skin pass and reduction stands) according to EN 15094;
Rollshop equipment;
Separate process technology (e. g., compressed air system, treatment of water and treatment of rolling lubricant);
Separate cleaning system for exhaust air;
Firefighting system.
NOTE: Protection of persons in case of using asphyxiant gases used in firefighting system is covered by this document, see Annex C.
This European Standard is not applicable to strip processing line machinery and equipment, which are manufactured before the date of publication of this standard by CEN.
NOTE: In case of revamping parts of a strip processing line, this European Standard should be used as a guideline for the parts to be revamped
Sicherheit von Maschinen - Sicherheitsanforderungen an Bandbehandlungsanlagen und Einrichtungen
Dieses Dokument legt die allgemeinen Sicherheitsanforderungen für Bandbehandlungsanlagen fest.
Dieses Dokument gilt für:
Bandbehandlungsanlagen für die Behandlung von Metallstreifen von
dem Coil-Übergabepunkt des Eingangsbereichs (mechanische Einrichtung, siehe 3.2) über
den Prozess (Behandlungs- und mechanische Einrichtungen, siehe 3.3 und 3.2) bis zum
Coil-Übergabepunkt des Ausgangsbereichs oder der Schnittstelle zu anderen Anlagen (mechanische Einrichtung), siehe Bild 1.
Bild 1 — Mechanische Einrichtungen und Behandlungsanlagen
ANMERKUNG 1 Die vorgenannten Prozesse können auch in Kombination auftreten.
Wenn der vorgenannte Prozess mit Prozessen kombiniert wird, die nicht im Anwendungsbereich dieser Norm liegen, kann diese Norm als Richtlinie verwendet werden.
ANMERKUNG 2 Thermoprozessanlagen, die in Bandbehandlungsanlagen integriert sind, werden durch die Normenreihe EN 746 abgedeckt. Für Trockner und Öfen, in denen brennbare Stoffe freigesetzt werden, gilt EN 1539.
Dieses Dokument behandelt nicht:
Thermoprozessanlagen, z. B. nach Normenreihe EN 746;
Trockner und Öfen nach EN 1539;
Coil-Transportsysteme vor der Coil-Übergabestelle am Einlaufteil und nach der Coil-Übergabestelle am Auslaufteil, z. B. Hakenbahnen, Brückenkräne, Gabelstapler und Güterwagen sowie andere Fahrzeuge;
Säureregenerierungsanlagen;
Regenerierungsanlagen, die nicht integraler Bestandteil der Bandbehandlungsanlage sind;
Lagerausrüstung für Coils;
Walzgerüste (d. h. Dressier- und Reduziergerüste) nach EN 15094;
Ausrüstung der Walzenwerkstatt;
separate Prozesstechnologie (z. B. Druckluftsystem, Wasseraufbereitung und Aufbereitung von Walzenschmierstoff);
separates Reinigungssystem für Abluft;
Brandbekämpfungsanlagen.
ANMERKUNG 3 Der Personenschutz bei der Verwendung von Erstickungsgasen in Brandbekämpfungsanlagen wird von diesem Dokument abgedeckt, siehe Anhang C.
Dieses Dokument behandelt die vorhersehbaren signifikanten Gefährdungen, Gefährdungssituationen und Ereignisse, die für Bandbehandlungsanlagen relevant sind, wenn diese bestimmungsgemäß und unter Fehlanwendungsbedingungen, die vernünftigerweise durch den Hersteller vorhersehbar sind, angewendet werden. Es beschreibt die von dem Hersteller zu erfüllenden Anforderungen, um die Sicherheit von Personen und Gegenständen während des Transports, der Inbetriebnahme, der Anwendung und der Außerbetriebnahme sowie im Fall von vorhersehbaren Ausfällen oder Fehlfunktionen, die an der Anlage auftreten können, sicherzustellen.
Für Modernisierungen ist es möglich, dieses Dokument (Typ-C-Norm) auf das zu modernisierende Teil anzuwenden.
Sécurité des machines - Prescription de sécurité pour machines et installations de traitement des bandes
Le présent document définit les exigences générales de sécurité des lignes de traitement des bandes.
Le présent document s'applique aux :
Lignes de traitement des bandes pour traiter des bandes métalliques, depuis le
- point de reprise de bobines de la section d’entrée (équipement terminal, voir 3.2) en passant par le
- procédé (équipement de traitement et équipement terminal, voir 3.3 et 3.2) jusqu’au
- point de reprise de bobines de la section de sortie ou à l'interface avec d’autres lignes (équipement terminal), voir la Figure 1.
Figure 1...
NOTE 1 Les procédés susmentionnés peuvent également exister en combinaison.
Si les procédés susmentionnés sont combinés avec des procédés qui ne sont pas couverts par le domaine d’application de la présente norme, la présente norme peut servir de ligne directrice.
NOTE 2 L’équipement thermique industriel intégré dans les lignes de traitement des bandes est couvert par la série EN 746. Pour les séchoirs et les fours, dans lesquels se dégagent des substances inflammables, l’EN 1539 s’applique.
Le présent document ne couvre pas :
- les équipements thermiques industriels, par exemple conformes à la série EN 746 ;
- les séchoirs et les fours conformes à l’EN 1539 ;
- les systèmes de transport de bobines avant le point de reprise à la section d’entrée et après le point de reprise à la section de sortie, par exemple convoyeurs à crochet, ponts roulants, élévateurs à fourche, chariots et autres véhicules ;
- les usines de régénération d’acide ;
- les usines de régénération qui ne font pas partie intégrante de la ligne de traitement des bandes ;
- les équipements de stockage des bobines ;
- les cages de laminoir (c'est-à-dire, les laminoirs d'écrouissage à froid et les cages de réduction) conformes à l’EN 15094 ;
- les équipements d’atelier de roulage ;
- les technologies à procédés séparés (par exemple, système à air comprimé, traitement de l’eau et traitement de lubrifiant de laminage) ;
- les systèmes de nettoyage séparé pour l’air extrait ;
- les systèmes de lutte contre l'incendie.
NOTE 3 La protection des personnes en cas d’usage de gaz asphyxiants utilisés dans un système de lutte contre l'incendie est couverte par le présent document, voir l’Annexe C.
Le présent document traite les phénomènes dangereux, situations dangereuses et événements dangereux significatifs prévisibles pertinents pour les lignes de traitement des bandes, lorsqu'elles sont utilisées normalement et dans les conditions de mauvais usage raisonnablement prévisible par le fabricant. Il définit les exigences auxquelles doit satisfaire le fabricant pour assurer la sécurité des personnes et des biens pendant le transport, la mise en service, l'utilisation, la mise hors service et la maintenance, ainsi que dans le cas de pannes ou de défauts de fonctionnement prévisibles, susceptibles d'affecter le matériel.
Pour la modernisation, le présent document (norme de type C) peut être appliqué pour la partie à moderniser.
Varnost strojev - Varnostne zahteve za linijske stroje in opremo za obdelavo (kovinskih) trakov
Ta evropski standard določa zdravstvene in varnostne zahteve za uporabo proizvodnih linij za obdelavo (kovinskih) trakov.
Ta evropski standard obravnava vsa večja tveganja, nevarne situacije in nevarne dogodke v zvezi z linijskimi stroji ter opremo za obdelavo (kovinskih) trakov, kadar se ti uporabljajo v skladu s predvidenim namenom ter pod pogoji, ki jih je predvidel proizvajalec, vendar vključuje tudi predvidene okvare in napake v primeru nepravilne uporabe.
Ta evropski standard se uporablja za:
– proizvodne linije za obdelavo kovinskih trakov: od mesta za prevzem zvitkov na vhodu prek celotnega procesa do mesta za prevzem zvitkov na izhodu ali vmesniku do drugih proizvodnih linij (terminalna oprema).
OPOMBA 1: Zgoraj omenjene proizvodne linije/procese je mogoče izvajati tudi v kombinaciji.
OPOMBA 2: Če se zgoraj omenjene proizvodne linije/procesi izvajajo v kombinaciji s procesi, ki ne spadajo na področje uporabe tega standarda, je priporočljivo uporabiti ta standard kot vodilo.
OPOMBA 3: Oprema za toplotno obdelavo, integrirana v proizvodne linije za obdelavo (kovinskih) trakov, je zajeta v skupini standardov EN 746. Za sušilnike in peči, v katerih se sproščajo vnetljive snovi, se uporablja standard EN 1539.
Ta evropski standard ne zajema:
– opreme za toplotno obdelavo, npr. v skladu s skupino standardov EN 746;
– sušilnikov in peči v skladu s standardom EN 1539;
– sistema za transport zvitkov pred mestom za prevzem zvitkov na vhodu in za mestom za prevzem zvitkov na izhodu (npr. transporterji s kljukami, mostni žerjavi, viličarji in železniški vagoni ter druga vozila);
– obratov za regeneracijo kislin;
– obratov za regeneracijo, ki niso sestavni del proizvodne linije za obdelavo (kovinskih) trakov;
– opreme za shranjevanje zvitkov;
– valjalnih strojev (npr. dresirni in redukcijski stroji) v skladu s standardom EN 15094;
– vrtljive opreme za obrate;
– ločene tehnologije procesov (npr. sistem stisnjenega zraka, čiščenje vode in obdelava maziva za valjalne stroje);
– ločenega sistema za čiščenje odvedenega zraka;
– sistema za gašenje požarov.
OPOMBA: Zaščita oseb v primeru uporabe zadušljivih plinov iz sistema za gašenje požarov je zajeta v tem dokumentu (glej dodatek C).
Ta evropski standard se ne uporablja za linijske stroje in opremo za obdelavo (kovinskih) trakov, ki so bili izdelani pred datumom izdaje tega standarda s strani Evropskega odbora za standardizacijo (CEN).
OPOMBA: V primeru preoblikovanja delov proizvodne linije za obdelavo (kovinskih) trakov naj bi se ta evropski standard uporabljal kot vodilo za dele, ki bodo preoblikovani.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 15061:2022
01-maj-2022
Nadomešča:
SIST EN 15061:2008+A1:2009
Varnost strojev - Varnostne zahteve za linijske stroje in opremo za obdelavo
(kovinskih) trakov
Safety of machinery - Safety requirements for strip processing line machinery and
equipment
Sicherheit von Maschinen - Sicherheitsanforderungen an Bandbehandlungsanlagen und
Einrichtungen
Sécurité des machines - Prescription de sécurité pour machines et installations de
traitement des bandes
Ta slovenski standard je istoveten z: EN 15061:2022
ICS:
13.110 Varnost strojev Safety of machinery
77.180 Oprema za metalurško Equipment for the
industrijo metallurgical industry
SIST EN 15061:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 15061:2022
---------------------- Page: 2 ----------------------
SIST EN 15061:2022
EN 15061
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 77.180; C Supersedes EN 15061:2007+A1:2008
English Version
Safety of machinery - Safety requirements for strip
processing line machinery and equipment
Sécurité des machines - Prescription de sécurité pour Sicherheit von Maschinen - Sicherheitsanforderungen
machines et installations de traitement des bandes an Bandbehandlungsanlagen und Einrichtungen
This European Standard was approved by CEN on 12 December 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15061:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
Contents Page
1 Scope . 5
2 Normative references . 6
3 Terms and definitions . 9
4 List of significant hazards . 14
4.1 General . 14
4.2 Interfaces to the linked/integrated equipment . 15
5 Safety requirements and/or protective/risk-reducing measures . 15
5.1 General . 15
5.2 Requirements for design, planning and risk assessment . 16
5.3 List of significant hazards, hazardous situations, safety requirements and/or
protective/risk reduction measures for terminal equipment . 34
5.4 List of significant hazards, hazardous situations, safety requirements and/or
protective/risk reduction measures for processing equipment . 55
6 Verification/validation of the safety requirements/functions and/or protective/risk
reduction measures . 81
6.1 General . 81
6.2 Required verification D . 82
6.3 Required verification V, M and T . 82
7 Information for use . 83
7.1 General . 83
7.2 Safety signs and warning devices . 83
7.3 Minimum marking . 83
7.4 Accompanying documents . 84
7.5 Training of personnel . 87
7.6 Remote access . 87
8 Supplementary information regarding repair work . 87
Annex A (normative) Requirements for shut-down, emergency stop and other stop
functions . 89
Annex B (normative) Noise test code . 94
Annex C (normative) Protection of persons in case of using asphyxiant gases used in
firefighting systems . 98
Annex D (informative) Exemplary solutions . 102
Annex E (informative) Example for the risk analysis due to interfaces . 106
Annex F (informative) Example for modes of operation in relation to segregated areas. 107
2
---------------------- Page: 4 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
European foreword
This document (EN 15061:2022) has been prepared by Technical Committee CEN/TC 322 “Equipment
for making and shaping of metals - Safety requirements”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards shall
be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15061:2007+A1:2008.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
Introduction
This document is a type-C standard as stated in EN ISO 12100:2010.
This document is not applicable to strip processing lines manufactured before the date of its publication.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the Scope of this document.
Where for clarity an example of a preventative measure is given, this should not be considered as the only
possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent
level of safety is achieved.
When requirements of this type-C standard are different from those which are stated in type-A or -B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine and/or plant manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine and/or plant operators/ employers (small, medium and large enterprises);
— service providers, e.g. for maintenance (small, medium and large enterprises).
The above-mentioned stakeholder groups have been given the possibility to participate in the drafting
process of this document.
4
---------------------- Page: 6 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
1 Scope
This document defines the general safety requirements of strip processing lines.
This document applies to:
Strip processing lines for treating metal strip, from
— coil take-over-point of the entry section (terminal equipment, see 3.2) through the
— process (processing and terminal equipment, see 3.3 and 3.2) up to the
— coil take-over-point of the exit section or interface to other lines (terminal equipment), see Figure 1.
Figure 1 — Terminal and processing equipment
NOTE 1 The aforementioned processes can also occur in combination.
If the aforementioned processes will be combined with processes which are not covered by the scope of
this document, this document can be used as a guideline.
NOTE 2 Thermo process equipment integrated in strip processing lines is covered by the EN 746 series. For
dryers and ovens, in which flammable substances are released, EN 1539 applies.
This document does not cover:
— thermo process equipment, e.g. in accordance with the EN 746 series;
— dryers and ovens in accordance with EN 1539;
— coil transporting system before coil take-over-point at the entry section and after coil take-over-
point at the exit section, e.g. hook conveyors, overhead cranes, fork lift and railway trucks and other
vehicles;
— acid regeneration plants;
— regeneration plants which are not integral part of the strip processing line;
— storage equipment for coils;
— rolling mill stands (i.e. skin pass and reduction stands) according to EN 15094;
5
---------------------- Page: 7 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
— rollshop equipment;
— separate process technology (e.g. compressed air system, treatment of water and treatment of rolling
lubricant);
— separate cleaning system for exhaust air;
— firefighting systems.
NOTE 3 Protection of persons in case of using asphyxiant gases used in firefighting system is covered by this
document, see Annex C.
This document deals with foreseeable significant hazards, hazardous situations and events relevant to
strip processing lines, when used as intended and under conditions of misuse which are reasonably
foreseeable by the manufacturer. It provides the requirements to be met by the manufacturer to ensure
the safety of persons and property during transport, commissioning, use, de-commissioning and
maintenance periods, as well as in the event of foreseeable failures or malfunctions that can occur in the
equipment.
For modernization, this document (type-C standard) can be applied for the part to be modernized.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 415-8, Safety of packaging machines - Part 8: Strapping machines
EN 614-1:2006+A1:2009, Safety of machinery - Ergonomic design principles - Part 1: Terminology and
general principles
EN 614-2, Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of
machinery and work tasks
EN 689, Workplace exposure - Measurement of exposure by inhalation to chemical agents - Strategy for
testing compliance with occupational exposure limit values
EN 746 (all parts), Industrial thermoprocessing equipment
EN 842, Safety of machinery - Visual danger signals - General requirements, design and testing
EN 981, Safety of machinery - System of auditory and visual danger and information signals
EN 1299, Mechanical vibration and shock - Vibration isolation of machines - Information for the application
of source isolation
EN 12198 (all parts), Safety of machinery - Assessment and reduction of risks arising from radiation emitted
by machinery
EN 12254, Screens for laser working places - Safety requirements and testing
EN 12464-1, Light and lighting - Lighting of work places - Part 1: Indoor work places
EN 13480 (all parts), Metallic industrial piping
6
---------------------- Page: 8 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
EN 14253, Mechanical vibration - Measurement and calculation of occupational exposure to whole-body
vibration with reference to health – Practical guidance
EN 15154-2, Emergency safety showers - Part 2: Plumbed-in eye wash units
EN 15154-5, Emergency safety showers - Part 5: Water overhead body showers for sites other than
laboratories
EN 15154-6, Emergency safety showers - Part 6: Plumbed-in multiple nozzle body showers for sites other
than laboratories
CLC/TR 60079-32-1:2018, Explosive atmospheres - Part 32-1: Electrostatic hazards, guidance
EN 60204-1:2018, Safety of machinery - Electrical equipment of machines - Part 1: General requirements
(IEC 60204-1:2016, modified)
EN 60825-1, Safety of laser products - Part 1: Equipment classification and requirements (IEC 60825-1)
EN 60825-4, Safety of laser products - Part 4: Laser guards (IEC 60825-4)
EN 61310-1, Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual,
acoustic and tactile signals (IEC 61310-1)
EN 61496-1, Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements
and tests (IEC 61496-1)
EN 61800-5-2:2017, Adjustable speed electrical power drive systems - Part 5-2: Safety requirements –
Functional (IEC 61800-5-2:2016)
EN 62061, Safety of machinery - Functional safety of safety-related electrical, electronic and programmable
electronic control systems (IEC 62061)
EN 62598, Nuclear instrumentation - Constructional requirements and classification of radiometric gauges
(IEC 62598)
EN ISO 4413, Hydraulic fluid power - General rules and safety requirements for systems and their
components (ISO 4413)
EN ISO 4414, Pneumatic fluid power - General rules and safety requirements for systems and their
components (ISO 4414)
EN ISO 4871:2009, Acoustics - Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)
EN ISO 7010, Graphical symbols - Safety colours and safety signs - Registered safety signs (ISO 7010)
EN ISO 7731, Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731)
EN ISO 10218-1, Robots and robotic devices - Safety requirements for industrial robots - Part 1: Robots
(ISO 10218-1)
EN ISO 10218-2, Robots and robotic devices - Safety requirements for industrial robots - Part 2: Robot
systems and integration (ISO 10218-2)
EN ISO 11064-1, Ergonomic design of control centres - Part 1: Principles for the design of control centres
(ISO 11064-1)
7
---------------------- Page: 9 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
EN ISO 11064-2, Ergonomic design of control centres - Part 2: Principles for the arrangement of control
suites (ISO 11064-2)
EN ISO 11064-3, Ergonomic design of control centres - Part 3: Control room layout (ISO 11064-3)
EN ISO 11064-6, Ergonomic design of control centres - Part 6: Environmental requirements for control
centres (ISO 11064-6)
EN ISO 11202:2010, Acoustics - Noise emitted by machinery and equipment - Determination of emission
sound pressure levels at a work station and at other specified positions applying approximate environmental
corrections (ISO 11202:2010)
EN ISO 11553-1, Safety of machinery - Laser processing machines - Part 1: Laser safety requirements (ISO
11553-1)
EN ISO 11688-1, Acoustics - Recommended practice for the design of low-noise machinery and equipment -
Part 1: Planning (ISO/TR 11688-1)
EN ISO 12100:2010, Safety of machinery - General principles for design - Risk assessment and risk reduction
(ISO 12100:2010)
EN ISO 13732-1, Ergonomics of the thermal environment - Methods for the assessment of human responses
to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1)
EN ISO 13849-1:2015, Safety of machinery - Safety-related parts of control systems - Part 1: General
principles for design (ISO 13849-1:2015)
EN ISO 13849-2, Safety of machinery - Safety-related parts of control systems - Part 2: Validation
(ISO 13849-2)
EN ISO 13850:2015, Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN ISO 13854, Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
(ISO 13854)
EN ISO 13855, Safety of machinery - Positioning of safeguards with respect to the approach speeds of parts
of the human body (ISO 13855)
EN ISO 13857, Safety of machinery - Safety distances to prevent hazard zones being reached by upper and
lower limbs (ISO 13857)
EN ISO 14118:2018, Safety of machinery - Prevention of unexpected start-up (ISO 14118:2017)
EN ISO 14119, Safety of machinery - Interlocking devices associated with guards - Principles for design and
selection (ISO 14119)
EN ISO 14120:2015, Safety of machinery - Guards - General requirements for the design and construction
of fixed and movable guards (ISO 14120:2015)
EN ISO 14122 (all parts), Safety of machinery - Permanent means of access to machinery (ISO 14122)
EN ISO 14123-1, Safety of machinery - Reduction of risks to health resulting from hazardous substances
emitted by machinery - Part 1: Principles and specifications for machinery manufacturers (ISO 14123-1)
EN ISO 14123-2, Safety of machinery - Reduction of risks to health resulting from hazardous substances
emitted by machinery - Part 2: Methodology leading to verification procedures (ISO 14123-2)
8
---------------------- Page: 10 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
ISO 3864-1, Graphical symbols — Safety colours and safety signs — Part 1: Design principles for safety signs
and safety markings
ISO/TR 22100-4:2018, Safety of machinery — Relationship with ISO 12100 — Part 4: Guidance to
machinery manufacturers for consideration of related IT-security (cyber security) aspects
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 12100:2010 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
NOTE Definitions used in EN and ISO standards referred to in this document are also valid for this document.
3.1
strip processing line
assembly of equipment for treating metal strip (surface treatment and/or to change the metal properties)
in which single machines (as described in 3.2 and 3.3) are linked by strip transport facilities and/or the
strip itself, including ancillary equipment
3.2
terminal equipment
equipment for moving, guiding, connecting, dividing and trimming the metal strip, coil handling
equipment and related ancillary equipment like hydraulic and pneumatic equipment and systems
3.3
processing equipment
equipment for surface treatment and/or modifying the metal strip properties
3.4
safety layout
graphic overview of the strip processing line with the arrangement of specific safety-related elements
and areas
Note 1 to entry: 5.2.5 specifies the safety related elements to be shown on the safety layout.
3.5
hazard zone
danger zone
any space within and/or around machinery in which a person can be exposed to a hazard
[SOURCE: EN ISO 12100:2010, 3.11]
3.6
take-over-point
point(s) where the strip processing line is connected to incoming/outgoing material (coils), media,
electricity (e.g. power supply and communication like input/output parameters)
Note 1 to entry: For example, coil take-over-point: Point where overhead cranes or other transport systems
deposit or remove coils.
9
---------------------- Page: 11 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
3.7
main route
marked traffic route
3.8
safeguard(ing)
guard or protective device
[SOURCE: EN ISO 12100:2010, 3.26]
3.9
trained person(nel)
skilled person with system knowledge, background knowledge, experience and/or ability to perform a
specific task and are aware of the hazards related to their duties
3.10
authorized person(nel)
trained person who is instructed by the user to perform a specific task on a specific equipment
Note 1 to entry: An unauthorized person does not have the required qualification and is not adequately
equipped, e.g. PPE.
3.11
maintenance
combination of service, inspection, reconditioning and functional test of the equipment
Note 1 to entry: The purpose is to preserve the working condition or returning to this condition so that the strip
processing line can perform the required function (including safety requirements).
3.11.1
service
measure to maintain the nominal condition
Note 1 to entry: The nominal condition can be maintained in general without dismantling/disassembling major
parts of the equipment, e.g. by cleaning and lubrication of the work equipment as well as addition or replacement
of agents or by replacing tools (e.g. rolls, knives).
3.11.2
inspection
measure to observe and assess the current condition as well as fault finding
Note 1 to entry: Measures, e.g. measuring, testing, diagnostics including the determination of the causes of wear
or damage and the derivation of the necessary consequences for the continued use.
Note 2 to entry: 3.11.2 does not cover "strip inspection", see 3.14.
3.11.3
reconditioning
foreseeable measure(s) to return to the nominal condition
Note 1 to entry: Foreseeable measures to replace worn parts or parts having expired the foreseen lifetime (could
require dismantling/disassembling). These parts should meet manufacturers' specification.
10
---------------------- Page: 12 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
3.11.4
functional test
checking the functionality of the exchanged or repaired parts
Note 1 to entry: It is maybe required to carry out adjustment work, e.g. test runs, verifying safety functions.
3.12
repair
not foreseeable measure(s) to return to the nominal condition
Note 1 to entry: Measure to replace damaged parts, requires in general dismantling/disassembling. These parts
should meet manufacturers' specification.
3.13
strip
metal strip in the production process, supplied and removed as coil
3.14
strip inspection
observe and assess the current condition of the material
3.15
cobbling
strip leaving its intended path
Note 1 to entry: Colliding with e.g. parts of the equipment is possible.
3.16
pulpit
enclosed room in which the control desk and monitoring facilities for a machine or equipment are located,
used as a permanent workstation
3.17
control stand
free standing control desk (usually situated adjacent to the machine or equipment), used as a temporary
workstation.
3.18
portable control device
control device which can be used in different places (e.g. control pendant, enabling button, radio control)
3.19
enabling (control) device
additional manually actuated device used in conjunction with a start control which, when continuously
actuated, permits machine function
[SOURCE: EN ISO 12100:2010, 3.28.2]
3.20
hold-to-run control device
control device which initiates and maintains machine functions only as long as the control device is
actuated
[SOURCE: EN ISO 12100:2010, 3.28.3]
11
---------------------- Page: 13 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
3.21
control mode
single machines or groups of linked machines of strip processing lines can function under different
control modes
Note 1 to entry: This document distinguishes between control mode(s) and operating mode(s) because there is
neither a common understanding nor a definition in EN ISO 12100 and EN 60204-1. The operating modes (see 3.22)
corresponds to the "control mode" of EN ISO 12100:2010, 6.2.11.9.
Note 2 to entry: For examples, see Figure D.1.
3.21.1
manual control mode
3.21.1.1
hold-to-run control
every function is initiated by an operator by means of a button or equivalent device according to
EN ISO 12100:2010, 3.28.3
Note 1 to entry: Release of the button/device stops the function (e.g. movement) immediately.
3.21.1.2
single function
specific functions are started and/or stopped by an operator
3.21.2
semi-automatic control
sequence of functions released once by an operator
Note 1 to entry: The released sequence is automatically stopped at its end. For the initiation of another sequence,
a new command by the operator is required.
3.21.3
automatic control
cycles of successive or parallel sequences, once initiated by the operator
Note 1 to entry: If no interruption takes place by an operator, the sequences are repeated as long as the running
conditions are met.
3.22
operating mode
state of the control system allowing to operate the strip processing line under defined line conditions
Note 1 to entry: Such modes are, e.g. production, safe stop, enabling, adjustment, inspection.
Note 2 to entry: The safety level of the operating mode(s) is defined as result of the risk assessment.
3.22.1
special mode
3.22.1.1
enabling mode
operating machine functions with an additional enabling control device (as per 3.19)
3.22.1.2
inching (jog) mode
operation of machine functions using a hold-to-run control device (as per 3.20)
12
---------------------- Page: 14 ----------------------
SIST EN 15061:2022
EN 15061:2022 (E)
3.22.2
safe stop (mode)
movement of the involved equipment is prevented through the control system
Note 1 to entry: The safety level of the safe stop is defined as result of the risk assessment.
Note 2 to entry: Safe stop is not sufficient as a safety measure to perform reconditioning or repair work because
isolation of the equipment from the relevant energy sources is not realized.
Note 3 to entry: Residual risks, e.g. by stored energy must have been secured by other means.
Note 4 to entry: Safe stop mode may also include switching off additional devices, e.g. X-ray.
3.22.3
normal production mode
machine is ready to produce or producing as intended
Note 1 to entry: Production, material handling and activities supporting these processes are covered.
Note 2 to entry: Maintenance according to 3.11 is not covered.
3.23
reduced speed
speed that is reduced to minimize the hazardous potential without safety-related speed monitoring
Note 1 to entry: In case of failure, an increase in speed may occur.
Note 2 to entry: Applies to linear or rotational speed.
Note 3 to entry: Speed reduced without an enabling device means that the movement is so slow that the operator
can move away from this dangerous movement in time. Based on a risk assessment, an enabling device may
therefore be required in some cases, even at
...
SLOVENSKI STANDARD
oSIST prEN 15061:2020
01-marec-2020
Varnost strojev - Varnostne zahteve za linijske stroje in opremo za obdelavo
(kovinskih) trakov
Safety of machinery - Safety requirements for strip processing line machinery and
equipment
Sicherheit von Maschinen - Sicherheitsanforderungen an Bandbehandlungsanlagen und
Einrichtungen
Sécurité des machines - Prescription de sécurité pour machines et installations de
traitement des bandes
Ta slovenski standard je istoveten z: prEN 15061
ICS:
13.110 Varnost strojev Safety of machinery
77.180 Oprema za metalurško Equipment for the
industrijo metallurgical industry
oSIST prEN 15061:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 15061:2020
---------------------- Page: 2 ----------------------
oSIST prEN 15061:2020
DRAFT
EUROPEAN STANDARD
prEN 15061
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2020
ICS
English Version
Safety of machinery - Safety requirements for strip
processing line machinery and equipment
Sécurité des machines - Prescription de sécurité pour Sicherheit von Maschinen - Sicherheitsanforderungen
machines et installations de traitement des bandes an Bandbehandlungsanlagen und Einrichtungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 322.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15061:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
Contents Page
1 Scope . 6
2 Normative references . 7
3 Terms and definitions . 10
4 List of significant hazards . 16
4.1 General . 16
4.2 Interfaces to the linked/integrated equipment . 16
5 Safety requirements and/or protective/risk-reducing measures . 16
5.1 General . 16
5.2 Requirements for design, planning and risk assessment . 17
5.3 List of significant hazards, hazardous situations, safety requirements and/or
protective/risk reduction measures for terminal equipment . 35
5.4 List of significant hazards, hazardous situations, safety requirements and/or
protective/risk reduction measures for processing equipment . 56
6 Verification/validation of the safety requirements/functions and/or protective/risk
reduction measures . 82
6.1 General . 82
6.2 Required verification D . 83
6.3 Required verification V, M and T . 83
7 Information for use . 84
7.1 General . 84
7.2 Safety signs and warning devices . 84
7.3 Minimum marking . 84
7.4 Accompanying documents . 85
7.5 Training of personnel . 88
8 Supplementary information regarding repair work . 88
Annex A (normative) Requirements for shut-down, emergency stop and other stop
functions . 89
Annex B (normative) Noise test code . 95
Annex C (normative) Protection of persons in case of using asphyxiant gases used in
firefighting systems . 99
Annex D (informative) Exemplary solutions . 103
Annex E (informative) Example for the risk analysis due to interfaces . 107
Annex F (informative) Example for modes of operation in relation to segregated areas . 108
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC (Machinery Directive) aimed to be covered . 109
Figures
Figure 1 — Terminal and processing equipment . 6
Figure 2 — Schematic representation of the life phases of a strip processing line . 17
2
---------------------- Page: 4 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
Figure D.1 — Examples for control modes (3.21) . 103
Figure D.2 — Movable platform (see 5.4.7.1) . 104
Figure D.3 — Example for protected walkways . 104
Figure D.4 — Example for protected walkways . 105
Figure D.5 — Example for protected inspection stand (horizontal) . 105
Figure D.6 — Example for an inspection stand protected by a door with guard locking and roofing
(see 5.3.13) . 106
Figure D.7 — Example of flange cover . 106
Figure E.1 — Diagram of a hypothetical plant indicating potentially hazardous interfaces . 107
Figure F.1 — Schematic diagram of modes of operation in relation to segregated areas . 108
Tables
Table 1 — Characteristic tasks and conditions for exemplary operating modes . 20
Table 2 — Hazards and corresponding risk parameters for the determination of PLr . 27
Table 3 — Main noise sources of strip processing lines and exemplary noise reduction measures . 34
Table 4 — List of significant hazards, hazardous situations, safety requirements and/or
protective/risk reduction measures for terminal equipment . 36
Table 5 — List of significant hazards, hazardous situations, safety requirements and/or
protective/risk reduction measures for processing equipment . 57
Table A.1 — Shut-down functions . 91
Table A.2 — Emergency stop and stop functions . 92
Table B.1 — Example of declared dual-number noise emission values for work stations . 98
Table ZA.1 — Correspondence between this European Standard and Annex I of
Directive 2006/42/EC . 109
3
---------------------- Page: 5 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
European foreword
This document (prEN 15061:2019) has been prepared by Technical Committee CEN/TC 322 “Equipment
for making and shaping metals”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document
4
---------------------- Page: 6 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
Introduction
This European Standard is a type C standard as stated in EN ISO 12100:2010.
This document is not applicable to strip processing lines manufactured before the date of its publication.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the Scope of this document.
Where for clarity an example of a preventative measure is given, this should not be considered as the only
possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent
level of safety is achieved.
When requirements of this Type-C standard are different from those which are stated in type-A or -B
standards, the requirements of this Type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this Type-C
standard.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine and/or plant manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine and/or plant users/employers (small, medium and large enterprises);
— service providers, e.g. for maintenance (small, medium and large enterprises).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
5
---------------------- Page: 7 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
1 Scope
This document defines the general safety requirements of strip processing lines.
This document applies to:
Strip processing lines for treating metal strip, from
— coil take-over-point of the entry section (terminal equipment, see 3.2) through the
— process (processing and terminal equipment, see 3.3 and 3.2) up to the
— coil take-over-point of the exit section or interface to other lines (terminal equipment), see Figure 1.
Figure 1 — Terminal and processing equipment
NOTE 1 The aforementioned processes can also occur in combination.
If the aforementioned processes will be combined with processes which are not covered by the scope of
this standard, this standard can be used as a guideline.
NOTE 2 Thermo process equipment integrated in strip processing lines is covered by the EN 746 series. For dryers
and ovens, in which flammable substances are released, EN 1539 applies.
This document does not cover:
— thermo process equipment, e.g. in accordance with the EN 746 series;
— dryers and ovens in accordance with EN 1539;
— coil transporting system before coil take-over-point at the entry section and after coil take-over-
point at the exit section, e.g. hook conveyors, overhead cranes, fork lift and railway trucks and other
vehicles;
— acid regeneration plants;
— regeneration plants which are not integral part of the strip processing line;
— storage equipment for coils;
— rolling mill stands (i.e. skin pass and reduction stands) according to EN 15094;
6
---------------------- Page: 8 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
— rollshop equipment;
— separate process technology (e.g. compressed air system, treatment of water and treatment of rolling
lubricant);
— separate cleaning system for exhaust air;
— firefighting systems.
NOTE 3 Protection of persons in case of using asphyxiant gases used in firefighting system is covered by this
document, see Annex C.
This document deals with foreseeable significant hazards, hazardous situations and events relevant to
strip processing lines, when used as intended and under conditions of misuse which are reasonably
foreseeable by the manufacturer. It provides the requirements to be met by the manufacturer to ensure
the safety of persons and property during transport, commissioning, use, de-commissioning and
maintenance periods, as well as in the event of foreseeable failures or malfunctions that can occur in the
equipment.
For modernization, this document (C-type standard) can be applied for the part to be modernized.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 614-1:2006+A1:2009, Safety of machinery - Ergonomic design principles - Part 1: Terminology and
general principles
EN 614-2, Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of
machinery and work tasks
EN 689, Workplace atmospheres - Guidance for the assessment of exposure by inhalation to chemical agents
for comparison with limit values and measurement strategy
EN 842, Safety of machinery - Visual danger signals - General requirements, design and testing
EN 981, Safety of machinery - System of auditory and visual danger and information signals
EN 1299, Mechanical vibration and shock - Vibration isolation of machines - Information for the application
of source isolation
EN 12094-1, Fixed firefighting systems - Components for gas extinguishing systems - Part 1: Requirements
and test methods for electrical automatic control and delay devices
EN 12198-1, Safety of machinery - Assessment and reduction of risks arising from radiation emitted by
machinery - Part 1: General principles
EN 12198-2, Safety of machinery - Assessment and reduction of risks arising from radiation emitted by
machinery - Part 2: Radiation emission measurement procedure
EN 12198-3, Safety of machinery — Assessment and reduction of risks arising from radiation emitted by
machinery — Part 3: Reduction of radiation by attenuation or screening
EN 12254, Screens for laser working places - Safety requirements and testing
7
---------------------- Page: 9 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
EN 12464-1, Light and lighting - Lighting of work places - Part 1: Indoor work places
EN 13480-1, Metallic industrial piping - Part 1: General
EN 13480-2, Metallic industrial piping - Part 2: Materials
1
EN 13480-3, Metallic industrial piping - Part 3: Design and calculation
EN 13480-4, Metallic industrial piping - Part 4: Fabrication and installation
EN 13480-5, Metallic industrial piping - Part 5: Inspection and testing
EN 14253, Mechanical vibration - Measurement and calculation of occupational exposure to whole-body
vibration with reference to health
CLC/TR 60079-32-1:2018, Explosive atmospheres - Part 32-1: Electrostatic hazards, guidance
EN 60204-1:2006, Safety of machinery - Electrical equipment of machines - Part 1: General requirements
(IEC 60204-1:2005)
EN 60825-1, Safety of laser products - Part 1: Equipment classification and requirements (IEC 60825-1)
EN 60825-4, Safety of laser products - Part 4: Laser guards (IEC 60825-4)
EN 61310-1, Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual,
acoustic and tactile signals (IEC 61310-1)
EN 61496-1, Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements
and tests (IEC 61496-1)
EN 61496-2, Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements
for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2)
EN IEC 61496-3, Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular
requirements for active opto-electronic protective devices responsive to diffuse reflection (AOPDDR) (IEC
61496-3)
EN 61800-5-2:2017, Adjustable speed electrical power drive systems - Part 5-2: Safety requirements –
Functional (IEC 61800-5-2)
EN 62598:2013, Nuclear instrumentation - Constructional requirements and classification of radiometric
gauges (IEC 62598)
EN ISO 4413, Hydraulic fluid power - General rules and safety requirements for systems and their
components (ISO 4413)
EN ISO 4414, Pneumatic fluid power - General rules and safety requirements for systems and their
components (ISO 4414)
EN ISO 4871:2009, Acoustics - Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)
EN ISO 7010, Graphical symbols - Safety colours and safety signs - Registered safety signs (ISO 7010)
8
---------------------- Page: 10 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
EN ISO 7731, Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731)
EN ISO 10218-1, Robots and robotic devices - Safety requirements for industrial robots - Part 1: Robots (ISO
10218-1)
EN ISO 10218-2, Robots and robotic devices - Safety requirements for industrial robots - Part 2: Robot
systems and integration (ISO 10218-2)
EN ISO 11064-1, Ergonomic design of control centres - Part 1: Principles for the design of control centres
(ISO 11064-1)
EN ISO 11064-2, Ergonomic design of control centres - Part 2: Principles for the arrangement of control
suites (ISO 11064-2)
EN ISO 11064-3, Ergonomic design of control centres - Part 3: Control room layout (ISO 11064-3)
EN ISO 11064-4, Ergonomic design of control centres - Part 4: Layout and dimensions of workstations (ISO
11064-4)
EN ISO 11064-5, Ergonomic design of control centres - Part 5: Displays and controls (ISO 11064-5)
EN ISO 11064-6, Ergonomic design of control centres - Part 6: Environmental requirements for control
centres (ISO 11064-6)
EN ISO 11064-7, Ergonomic design of control centres - Part 7: Principles for the evaluation of control
centres (ISO 11064-7)
EN ISO 11202, Acoustics - Noise emitted by machinery and equipment - Determination of emission sound
pressure levels at a work station and at other specified positions applying approximate environmental
corrections (ISO 11202)
EN ISO 11688-1, Acoustics - Recommended practice for the design of low-noise machinery and equipment -
Part 1: Planning (ISO/TR 11688-1)
EN ISO 12100:2010, Safety of machinery - General principles for design - Risk assessment and risk reduction
(ISO 12100:2010)
EN ISO 13732-1, Ergonomics of the thermal environment - Methods for the assessment of human responses
to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1)
EN ISO 13849-1:2015, Safety of machinery - Safety-related parts of control systems - Part 1: General
principles for design (ISO 13849-1:2015)
EN ISO 13850:2015, Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN ISO 13854, Safety of machinery - Minimum gaps to avoid crushing of parts of the human body (ISO
13854)
EN ISO 13855:2010, Safety of machinery - Positioning of safeguards with respect to the approach speeds of
parts of the human body (ISO 13855:2010)
EN ISO 13857, Safety of machinery - Safety distances to prevent hazard zones being reached by upper and
lower limbs (ISO 13857)
EN ISO 14118:2018, Safety of machinery - Prevention of unexpected start-up (ISO 14118:2017)
9
---------------------- Page: 11 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
EN ISO 14119, Safety of machinery - Interlocking devices associated with guards - Principles for design and
selection (ISO 14119)
EN ISO 14120:2015, Safety of machinery - Guards - General requirements for the design and construction
of fixed and movable guards (ISO 14120:2015)
EN ISO 14122-1, Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed
means and general requirements of access (ISO 14122-1)
EN ISO 14122-2, Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms
and walkways (ISO 14122-2)
EN ISO 14122-3, Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders
and guard-rails (ISO 14122-3)
EN ISO 14122-4, Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO
14122-4)
EN ISO 14123-1, Safety of machinery - Reduction of risks to health resulting from hazardous substances
emitted by machinery - Part 1: Principles and specifications for machinery manufacturers (ISO 14123-1)
EN ISO 14123-2, Safety of machinery - Reduction of risks to health resulting from hazardous substances
emitted by machinery - Part 2: Methodology leading to verification procedures (ISO 14123-2)
EN ISO 15004-1, Ophthalmic instruments - Fundamental requirements and test methods - Part 1: General
requirements applicable to all ophthalmic instruments (ISO 15004-1)
ISO 3864-1, Graphical symbols - Safety colours and safety signs - Part 1: Design principles for safety signs
and safety markings
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 12100:2010 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• ISO Online browsing platform: available at https://www.iso.org/obp
• IEC Electropedia: available at http://www.electropedia.org/
Note 1 to entry: Definitions used in EN and ISO standards referred to in this document are also valid for this
document.
3.1
strip processing line
assembly of equipment for treating metal strip (surface treatment and/or to change the metal properties)
in which single machines (as described in 3.2 and 3.3) are linked by strip transport facilities and/or the
strip itself, including ancillary equipment
3.2
terminal equipment
equipment for moving, guiding, connecting, dividing and trimming the metal strip, coil handling
equipment and related ancillary equipment like hydraulic and pneumatic equipment and systems
10
---------------------- Page: 12 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
3.3
processing equipment
equipment for surface treatment and/or modifying the metal strip properties
3.4
safety layout
graphic overview of the strip processing line with the arrangement of specific safety-related elements
and areas
Note 1 to entry: 5.2.5 specifies the safety related elements to be shown on the safety layout.
3.5
hazard zone
danger zone
any space within and/or around machinery in which a person can be exposed to a hazard
[EN ISO 12100:2010, 3.11]
3.6
take-over-point(s)
point(s) where the strip processing line is connected to incoming/outgoing material (coils), media,
electricity (e.g. power supply and communication like input/output parameters)
Note 1 to entry: For example, coil take-over-point: Point where overhead cranes or other transport systems
deposit or remove coils
3.7
main route(s)
marked traffic route
3.8
safeguard(ing)
guard or protective device
[EN ISO 12100:2010, 3.26]
3.9
trained person(nel)
skilled person with system knowledge, background knowledge, experience and/or ability to perform a
specific task and are aware of the hazards related to their duties
3.10
authorized person(nel)
trained person who is instructed by the user to perform a specific task on a specific equipment
Note 1 to entry: An unauthorized person does not have the required qualification and is not adequately
equipped, e.g. PPE.
3.11
maintenance
combination of service, inspection, reconditioning and functional test of the equipment
Note 1 to entry: The purpose is to preserve the working condition or returning to this condition so that the strip
processing line can perform the required function (including safety requirements)
11
---------------------- Page: 13 ----------------------
oSIST prEN 15061:2020
prEN 15061:2020 (E)
3.11.1
service
measure to maintain the nominal condition
Note 1 to entry: The nominal condition can be maintained in general without dismantling/disassembling major
parts of the equipment, e.g. by cleaning and lubrication of the work equipment as well as addition or replacement
of agents or by replacing tools (e.g. rolls, knives)
3.11.2
inspection
measure to observe and assess the current condition as well as fault finding
Note 1 to entry: Measures, e.g. measuring, testing, diagnostics including the determination of the causes of wear
or damage and the derivation of the necessary consequences for the continued use
Note 2 to entry: 3.11.2 does not cover "strip inspection", see 3.14
3.11.3
reconditioning
foreseeable measure(s) to return to the nominal condition
Note 1 to entry: Foreseeable measures to replace worn parts or parts having expired the foreseen lifetime (could
require dismantling/disassembling). These parts should meet manufacturers' specification
3.11.4
functional test
checking the functionality of the exchanged or repaired parts
Note 1 to entry: It is maybe required to carry out adjustment work, e.g. test runs, verifying safety functions.
3.12
repair
not foreseeable measure(s) to return to the nominal condition
Note 1 to entry: Measure to replace damaged parts, requires in general dismantling/disassembling. These parts
should meet manufacturers' specification.
3.13
strip
metal strip in the production process, supplied and removed as coil
3.14
strip inspection
observe and assess the current condition of the material
3.15
cobbling
strip leaving its intended path
Note 1 to entry: Colliding with e.g. parts of the equipment is possible.
3.16
pulpit
enclosed room in which the control desk and monitoring facilities for a machine or equipment are located,
used as a permanent workstation
12
---------------------- Page: 14 ----------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.