Switches for appliances - Part 1: General requirements (IEC 61058-1:2016)

This part of IEC 61058 applies to switches for appliances. The switches are intended to
control electrical appliances and other equipment for household or similar purposes with a
rated voltage not exceeding 480 V and a rated current not exceeding 63 A.
Switches for appliances are intended to be operated by
– a person via an actuating member,
– indirect actuation,
– an actuating sensing unit.
Transmission of a signal between the actuating member or sensing unit and the switch may
be connected by optical, acoustic, thermal, electrical or other relevant connection and may
include remote controlled units.
This part of IEC 61058 applies to switches for appliances provided with additional control
functions governed by the switch provided with electronic circuits and devices that are
necessary for the intended and/or correct operation of the switch.
This part of IEC 61058 applies to circuitry when evaluated with a switch and necessary for the
switching function.
This part of IEC 61058 applies in general to switches for appliances in conjunction with the
following parts:
– Part 1-1: Requirements for mechanical switches, and/or
– Part 1-2: Requirements for electronic switches.
This part of IEC 61058 does not apply to devices covered by:
– IEC 60669 (all parts), Switches for household and similar fixed-electrical installations, and
– IEC 60730 (all parts), Automatic electrical controls.
This part of IEC 61058 does not contain requirements for safety isolating switches
(IEC 60050-811:1991, 811-29-17).
NOTE 1 For switches used in tropical climates, additional requirements may be necessary.
NOTE 2 Attention is drawn to the fact that the end product standards for appliances may contain additional or
alternative requirements for switches.
NOTE 3 Throughout this part of IEC 61058, the word "appliance" means "appliance or equipment".

Geräteschalter - Teil 1: Allgemeine Anforderungen (IEC 61058-1:2016)

Interrupteurs pour appareils - Partie 1: Règles générales (IEC 61058-1:2016)

L'IEC 61058-1:2016 s'applique d'une manière générale aux interrupteurs pour appareils. Les interrupteurs permettent de commander des appareils électriques et autres matériels pour usage domestique et analogue dont la tension assignée ne dépasse pas 480 V et le courant assigné ne dépasse pas 63 A. Cette quatrième édition annule et remplace la troisième édition parue en 2000, l'amendement 1:2001 et l'amendement 2:2007. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) les exigences relatives aux constructions d'interrupteurs mécaniques sont maintenant incluses dans l'IEC 61058-1-1; b) les exigences relatives aux constructions d'interrupteurs électroniques sont maintenant incluses dans l'IEC 61058-1-2.

Stikala za aparate - 1. del: Splošne zahteve (IEC 61058-1:2016)

Ta del standarda IEC 61058 se uporablja za stikala za aparate. Stikala so namenjena upravljanju električnih aparatov in druge opreme za gospodinjstvo ali podobne namene z nazivno napetostjo, ki ne presega 480 V, ter z nazivnim tokom, ki ne presega 63 A.
Stikala za aparate upravlja
– oseba prek sprožilnega elementa,
– posredno proženje,
– sprožilna enota za zaznavanje dotika.
Prenos signala med sprožilnim elementom ali enoto za zaznavanje in stikalom se lahko izvaja prek optične, akustične, toplotne, električne ali druge ustrezne povezave in lahko zajema enote za daljinsko upravljanje.
Ta del standarda IEC 61058 se uporablja za stikala za aparate z dodatnimi nadzornimi funkcijami, ki jih upravlja stikalo, povezano z elektronskimi vezji in napravami, ki so potrebne za namensko in/ali pravilno delovanje stikala.
Ta del standarda IEC 61058 se uporablja za vezje, kadar se to vrednoti s stikalom in je potrebno za funkcijo preklapljanja.
Ta del standarda IEC 61058 se uporablja za stikala za aparate v povezavi z naslednjimi deli:
1-1. del: Zahteve za mehanska stikala, in/ali
1-2. del: Zahteve za elektronska stikala.
Ta del standarda IEC 61058 se ne uporablja za naprave, ki jih zajemata standarda:
– IEC 60669 (vsi deli), Stikala za gospodinjske in podobne fiksne električne napeljave, in
– IEC 60730 (vsi deli), Avtomatske električne krmilne naprave.
Ta del standarda IEC 61058 ne vsebuje zahtev za varnostne ločilnike (IEC 60050-811:1991, 811-29-17).
OPOMBA 1: Za stikala, uporabljena v tropskih podnebjih, so lahko potrebne dodatne zahteve. OPOMBA 2: Upoštevajte, da lahko standardi za končni izdelek aparatov vsebujejo dodatne ali drugačne zahteve za stikala.
OPOMBA 3: V celotnem tem delu standarda IEC 61058 beseda »aparat« pomeni »aparat ali opremo«.

General Information

Status
Published
Publication Date
20-Aug-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
16-Jul-2018
Due Date
20-Sep-2018
Completion Date
21-Aug-2018

RELATIONS

Buy Standard

Standard
SIST EN IEC 61058-1:2018
English language
128 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stikala za aparate - 1. del: Splošne zahteve (IEC 61058-1:2016)Geräteschalter - Teil 1: Allgemeine Anforderungen (IEC 61058-1:2016)Interrupteurs pour appareils - Partie 1: Règles générales (IEC 61058-1:2016)Switches for appliances - Part 1: General requirements (IEC 61058-1:2016)29.120.40StikalaSwitchesICS:Ta slovenski standard je istoveten z:EN IEC 61058-1:2018SIST EN IEC 61058-1:2018en,fr,de01-september-2018SIST EN IEC 61058-1:2018SLOVENSKI

STANDARDSIST EN 61058-1:2003/A2:2008SIST EN 61058-1:20031DGRPHãþD
SIST EN IEC 61058-1:2018
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN IEC 61058-1
May 2018 ICS 29.120.40
Supersedes
EN 61058-1:2002
English Version
Switches for appliances - Part 1: General requirements (IEC 61058-1:2016)
Interrupteurs pour appareils - Partie 1: Exigences générales (IEC 61058-1:2016)

Geräteschalter - Teil 1: Allgemeine Anforderungen (IEC 61058-1:2016) This European Standard was approved by CENELEC on 2016-08-24. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization

Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23,

B-1040 Brussels © 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN IEC 61058-1:2018 E SIST EN IEC 61058-1:2018

EN IEC 61058-1:2018 (E) 2 European foreword The text of document 23J/401/FDIS, future edition 4 of IEC 61058-1, prepared by SC 23J "Switches for appliances", of IEC/TC 23 "Electrical accessories" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61058-1:2017. The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-11-25 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2021-05-25

This document supersedes EN 61058-1:2002. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For the relationship with EU Directives 2014/30/EU and 2014/35/EU, see informative Anne•es ZZA and ZZB, which are an integral part of this document. Endorsement notice The text of the International Standard IEC 61058-1:2016 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60034-1:2010 NOTE Harmonized as EN 60034-1:2010 (modified). IEC 60068-2-20:2008 NOTE Harmonized as EN 60068-2-20:2008 (not modified). IEC 60085:2007 NOTE Harmonized as EN 60085:2008 (not modified). IEC 60228:2004 NOTE Harmonized as EN 60228:2005 (not modified). IEC 60335-1 NOTE Harmonized as EN 60335-1. IEC 60335-2 NOTE Harmonized in EN 60335-2 series. IEC 60664-1:2007 NOTE Harmonized as EN 60664-1:2007 (not modified). IEC 60893-1:2004 NOTE Harmonized as EN 60893-1:2004 (not modified). SIST EN IEC 61058-1:2018

EN IEC 61058-1:2018 (E) 3 IEC 60998-2-3:2002 NOTE Harmonized as EN 60998-2-3:2004 (modified). IEC 61000 NOTE Harmonized in EN 61000 series. IEC 61140 NOTE Harmonized as EN 61140.

SIST EN IEC 61058-1:2018
EN IEC 61058-1:2018 (E) 4 Annex ZA (normative)

Normative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.

Publication Year Title EN/HD Year IEC 60038 - IEC standard voltages EN 60038 2011

IEC 60060-1 - High-voltage test techniques - Part 1: General definitions and test requirements EN 60060-1 2010

IEC 60065 (mod) 2014

Audio, video and similar electronic apparatus - Safety requirements EN 60065 2014

+ A11 2017

IEC 60068-2-75 - Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests EN 60068-2-75 2014

IEC 60112 2003

Method for the determination of the proof and the comparative tracking indices of solid insulating materials EN 60112 2003

+ A1 2009
+ A1 2009
IEC 60127 series
Miniature fuses EN 60127 series
IEC 60127-2 - Miniature fuses - Part 2: Cartridge fuse-links EN 60127-2 2014

IEC 60269-3 - Low-voltage fuses - Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F HD 60269-3 2010

+ A1 2013

IEC 60384-14 - Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains EN 60384-14 2013

+ A1 2016
IEC 60417 - Graphical symbols for use on equipment - -
SIST EN IEC 61058-1:2018
EN IEC 61058-1:2018 (E) 5 Publication Year Title EN/HD Year IEC 60529 1989
Degrees of protection provided by enclosures (IP Code) EN 60529 1991
- -
+ corr. May 1993
+ A1 1999
+ A1 2000
+ A2 2013
+ A2 2013
IEC 60617 - Graphical symbols for diagrams - -
IEC 60664-3 2003

Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution EN 60664-3 2003

+ A1 2010
+ A1 2010
IEC 60691 - Thermal-links - Requirements and application guide EN 60691 2016

IEC 60695-2-11 - Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) EN 60695-2-11 2014

IEC 60695-10-2 - Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method EN 60695-10-2 2014

IEC 60695-11-10 - Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods EN 60695-11-10 2013

IEC 60695-11-20 - Fire hazard testing - Part 11-20: Test flames - 500 W flame test methods EN 60695-11-20 2015

+ AC 2014 IEC 60730 series
Automatic electrical controls
EN 60730 series
IEC 60730-1 (mod) 2013
Automatic electrical controls - Part 1: General requirements EN 60730-1 2016
+ A1 2016
IEC 60730-2-9 2015

Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls EN 60730-2-9 2016 IEC 60738-1 - Thermistors - Directly heated positive temperature coefficient - Part 1: Generic specification EN 60738-1 2006

+ A1 2009

IEC 61000-3-2 - Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current ≤ 16 A per phase) EN 61000-3-2 2014

IEC 61000-3-3 - Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection EN 61000-3-3 2013

IEC/TS 61000-3-5 - Electromagnetic compatibility (EMC) - Part 3-5: Limits - Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 75 A - -

SIST EN IEC 61058-1:2018

EN IEC 61058-1:2018 (E) 6 Publication Year Title EN/HD Year IEC 61000-4-2 - Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test EN 61000-4-2 2009

IEC 61000-4-3 - Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test EN 61000-4-3 2006

+ A1 2008
+ A2 2010

IEC 61000-4-4 - Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test EN 61000-4-4 2012

IEC 61000-4-5 - Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test EN 61000-4-5 2014

IEC 61000-4-8 - Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test EN 61000-4-8 2010

IEC 61000-4-11 - Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests EN 61000-4-11 2004

+ A1 2017
IEC 61032 1997

Protection of persons and equipment by enclosures - Probes for verification EN 61032 1998

IEC 61058-1-1 - Switches for appliances - Part 1-1: Requirements for mechanical switches EN 61058-1-1 2016

IEC 61058-1-2 - Switches for appliances - Part 1-2: Requirements for electronic switches EN 61058-1-2 2016

IEC 61210 (mod) 2010

Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements EN 61210 2010

CISPR 14-1 - Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission EN 55014-1 2006

+ A1 2009
+ A2 2011
CISPR 15 2013

Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment EN 55015 2013

+ A1 2015
SIST EN IEC 61058-1:2018
EN IEC 61058-1:2018 (E) 7 Annex ZZA (informative)

Relationship between this European Standard and the essential requirements of Directive 2014/30/EU [2014 OJ L96] aimed to be covered This European Standard has been prepared under a Commission’s standardization request as regards harmonized standards in support of Directive 2014/30/EU relating to electromagnetic compatibility, M/552 C(2016)7641, to provide one voluntary means of conforming to essential requirements of Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonization of the laws of the Member States relating to electromagnetic compatibility [2014 OJ L96]. Once this standard is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of this standard given in Table ZZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. Table ZZA.1 – Correspondence between this European standard and Annex I of Directive 2014/30/EU [2014 OJ L96] Essential requirements of Directive 2014/30/EU Clause(s) / sub-clause(s) of this EN Remarks / Notes 1. General requirements

Equipment shall be so designed and manufactured, having regard to the state of the art, as to ensure that:

(a) the electromagnetic disturbance generated does not exceed the level above which radio and telecommunications equipment or other equipment cannot operate as intended Clause 25 EMC requirements

(b) it has a level of immunity to the electromagnetic disturbance to be expected in its intended use which allows it to operate without unacceptable degradation of its intended use. Clause 25 EMC requirements

2. Specific requirements for fixed installations Not in the scope of EN 61058-1, -1-1 and -1-2

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European standard is maintained in the list published in the Official Journal of the European Union. Users of this standard should consult frequently the latest list published in the Official Journal of the European Union. WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of this standard. SIST EN IEC 61058-1:2018

EN IEC 61058-1:2018 (E) 8 Annex ZZB (informative)

Relationship between this European standard and the safety objectives of Directive 2014/35/EU [2014 OJ L96] aimed to be covered This European Standard has been prepared under a Commission’s standardization request relating to harmonized standards in the field of the Low Voltage Directive, M/511, to provide one voluntary means of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonization of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits [2014 OJ L96]. Once this standard is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of this standard given in Table ZZB.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding safety objectives of that Directive, and associated EFTA regulations. Table ZZB.1 – Correspondence between this European standard and Annex I of Directive 2014/35/EU [2014 OJ L96] Safety objectives of Directive 2014/35/EU Clause(s) / sub-clause(s) of this EN Remarks / Notes 1. General Conditions EN 61058-1, -1-1, -1-2 Implement Annex ZZ in EN 61058-1and link to in EN 61058-1-1 and -1-2 (a) the essential characteristics, the recognition and observance of which will ensure that electrical equipment will be used safely and in applications for which it was made, shall be marked on the electrical equipment, or, if this is not possible, on an accompanying document clause 1, clause 4, clause 6, clause 7, clause 8

(b) the electrical equipment, together with its component parts, shall be made in such a way as to ensure that it can be safely and properly assembled and connected clause 9, clause 10, clause 11 clause 12, clause 14, clause 19, clause 20

(c) the electrical equipment shall be so designed and manufactured as to ensure that protection against the hazards set out in points 2 and 3 is assured, providing that the equipment is used in applications for which it was made and is adequately maintained clause 12, clause 13, clause 14, clause 15, clause 16, clause 17, clause 18, clause 19, clause 20, clause 21, clause 22, clause 23, clause 24, clause 25

2. Protection against hazards EN 61058-1, -1-1, -1-2 Implement Annex ZZ in EN SIST EN IEC 61058-1:2018

EN IEC 61058-1:2018 (E) 9 arising from the electrical equipment 61058-1and link to in EN 61058-1-1 and -1-2 (a) persons and domestic animals are adequately protected against the danger of physical injury or other harm which might be caused by direct or indirect contact Clause 1, clause 9, clause 10, cause 20

(b) temperatures, arcs or radiation which would cause a danger, are not produced Clause 16, clause 21

(c) persons, domestic animals and property are adequately protected against non-electrical dangers caused by the electrical equipment which are revealed by experience Clause 18

(d) the insulation is suitable for foreseeable conditions Clause 10, clause 15, clause 20

3. Protection against hazards which may be caused by external influences on the electrical equipment EN 61058-1, -1-1, -1-2 Implement Annex ZZ in EN 61058-1and link to in EN 61058-1-1 and -1-2 (a) meets the expected mechanical requirements in such a way that persons, domestic animals and property are not endangered Clause 18

(b) is resistant to non-mechanical influences in expected environmental conditions, in such a way that persons, domestic animals and property are not endangered Clause 14, clause 22, clause 25

(c) does not endanger persons, domestic animals and property in foreseeable conditions of overload Clause 7, clause 23

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European standard is maintained in the list published in the Official Journal of the European Union. Users of this standard should consult frequently the latest list published in the Official Journal of the European Union. WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of this standard.

SIST EN IEC 61058-1:2018
SIST EN IEC 61058-1:2018

IEC 61058-1 Edition 4.0 2016-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Switches for appliances –

Part 1: General requirements
Interrupteurs pour appareils –
Partie 1: Exigences générales

INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE

ICS 29.120.40
ISBN 978-2-8322-3466-2
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé. SIST EN IEC 61058-1:2018

– 2 – IEC 61058-1:2016  IEC 2016 CONTENTS FOREWORD......................................................................................................................... 6 1 Scope ............................................................................................................................ 8 2 Normative references .................................................................................................... 9 3 Terms and definitions .................................................................................................. 11 3.1 General terms and definitions .............................................................................. 11 3.2 Terms and definitions relating to voltage and current ........................................... 13 3.3 Terms and definitions relating to the different types of switches ........................... 15 3.4 Terms and definitions relating to the operation of the switch ................................. 16 3.6 Terms and definitions relating to terminals and terminations ................................. 17 3.7 Terms and definitions relating to insulation .......................................................... 18 3.8 Terms and definitions relating to pollution ............................................................ 20 3.9 Terms and definitions relating to manufacturers’ tests .......................................... 20 4 General requirements .................................................................................................. 20 5 General information on tests ........................................................................................ 21 5.1 Testing shall be performed according to the general guideline information provided in Clause 5 ........................................................................................... 21 5.2 Electrical information ........................................................................................... 21 5.3 Test loads on multiway switches .......................................................................... 22 5.4 Test specimens ................................................................................................... 22 6 Rating ......................................................................................................................... 23 7 Classification ............................................................................................................... 23 7.1 According to nature of supply .............................................................................. 23 7.2 According to type of load to be controlled by each circuit of the switch ................. 23 7.3 According to ambient temperature ....................................................................... 23 7.4 According to number of operating cycles .............................................................. 24 7.5 Degree of protection against solid foreign objects ................................................ 24 7.6 Degree of protection against ingress of water ...................................................... 24 7.7 According to degree of protection against electric shock for an incorporated switch for use in .................................................................................................. 25 7.8 According to degree of pollution inside the switch ................................................ 25 7.9 According to degree of pollution outside the switch .............................................. 25 7.10 According to marking ........................................................................................... 25 7.11 According to resistance to ignitability by the glow wire temperature ...................... 25 7.12 According to the rated impulse withstand voltage ................................................. 26 7.13 According to the rated overvoltage category ........................................................ 26 7.14 According to type of disconnection ...................................................................... 26 7.15 According to the type of coating for rigid printed board assemblies ....................... 26 7.16 According to type and/or connection of switches .................................................. 26 7.17 According to configuration of switching device ..................................................... 27 7.18 According to duty type ......................................................................................... 27 7.19 According to linkage between contact and actuator speed .................................... 27 7.20 According to the type of terminals ........................................................................ 27 7.21 According to the type of built in protection ........................................................... 28 7.22 According to the type of forced cooling ................................................................ 28 7.23 According to the capacitor provided with the switch .............................................. 29 8 Marking and documentation ......................................................................................... 36 SIST EN IEC 61058-1:2018

IEC 61058-1:2016  IEC 2016 – 3 – 8.1 Switch information ............................................................................................... 36 8.2 Symbols .............................................................................................................. 39 8.3 Load rating ......................................................................................................... 40 8.4 Temperature rating .............................................................................................. 42 8.5 Operating cycles ................................................................................................. 43 8.6 Switches intended for use in Class II equipment or appliances ............................. 43 8.7 Required marking ................................................................................................ 43 8.8 Legibility and durability of marking ....................................................................... 43 8.9 Switches with their own enclosure ....................................................................... 44 9 Protection against electric shock .................................................................................. 44 10 Provision for earthing ................................................................................................... 46 11 Terminals and terminations .......................................................................................... 47 11.1 Common requirements to terminals ..................................................................... 47 11.2 Fixing of terminals ............................................................................................... 49 11.3 Location and shielding of terminals ...................................................................... 49 11.4 Terminals for interconnection of more than one conductors .................................. 49 11.5 Thermal stress .................................................................................................... 49 11.6 Test sequences ................................................................................................... 50 11.7 Conductor escape test (TT1) ............................................................................... 50 11.8 Terminal displacement test (TT2) ........................................................................ 51 11.9 Strand escape test (TT3) ..................................................................................... 52 11.10 Multiple conductors (TT4) .................................................................................... 53 12 Construction ................................................................................................................ 53 12.1 Constructional requirements relating to protection against electric shock .............. 53 12.2 Constructional requirements relating to safety during mounting and normal operation of the switch ........................................................................................ 54 12.3 Constructional requirements relating to the mounting of switches and to the attachment of cords ............................................................................................. 54 13 Mechanism .................................................................................................................. 55 14 Protection against ingress of solid foreign objects, ingress of water and humid conditions .................................................................................................................... 56 14.1 Protection against ingress of solid foreign objects ................................................ 56 14.2 Protection against ingress of water ...................................................................... 56 14.3 Protection against humid conditions ..................................................................... 57 15 Insulation resistance and dielectric strength ................................................................. 58 15.1 General requirements .......................................................................................... 58 15.2 Measurement of insulation resistance .................................................................. 58 15.3 Insulation test voltage ......................................................................................... 59 16 Heating ....................................................................................................................... 60 16.1 General requirements .......................................................................................... 60 16.2 Contacts and terminals ........................................................................................ 60 16.3 Other parts ......................................................................................................... 60 16.4 Heating test ........................................................................................................ 60 17 Endurance ................................................................................................................... 61 18 Mechanical strength ..................................................................................................... 61 18.1 General requirements .......................................................................................... 61 18.2 Impact ................................................................................................................ 61 18.3 Pull ..................................................................................................................... 62 SIST EN IEC 61058-1:2018

– 4 – IEC 61058-1:2016  IEC 2016 18.4 Push ................................................................................................................... 62 19 Screws, current-carrying parts and connections ............................................................ 63 19.1 General requirements for electrical connections ................................................... 63 19.2 Screwed connections .......................................................................................... 63 19.3 Current-carrying parts ......................................................................................... 66 20 Clearances, creepage distances, solid insulation and coatings of rigid printed board assemblies ........................................................................................................ 66 20.1 General requirements .......................................................................................... 66 20.2 Clearances ...............................................

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.