SIST EN 300 330 V2.1.1:2017

Short Range Devices (SRD) - Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

The present document specifies technical characteristics and methods of measurements for the following Short Range
Device major equipment types:
1) Generic Short range Devices including transmitters and receivers operating in the range from 9 kHz to
25 MHz; and
2) inductive loop transmitters and receivers operating from 9 kHz to 30 MHz including Radio Frequency
Identification (RFID), Near Field Communication (NFC) and Electronic Article Surveillance (EAS) operating
in LF and HF ranges.
Also the present document covers fixed, mobile and portable stations.
NOTE: If a system includes transponders, these are measured together with the transmitter.

Naprave kratkega dosega (SRD) - Radijska oprema v frekvenčnem območju od 9 kHz do 25 MHz in sistemi z indukcijsko zanko v frekvenčnem območju od 9 kHz do 30 MHz - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU

Ta dokument določa tehnične karakteristike in merilne metode za naslednje glavne vrste naprav kratkega dosega:
1) generične naprave kratkega dosega, vključno z oddajniki in sprejemniki za uporabo v območju od 9 kHz do 25 MHz; ter
2) oddajnike in sprejemnike z indukcijsko zanko za uporabo v območju od 9 kHz do 30 MHz, vključno z radiofrekvenčno identifikacijo (RFID), komunikacijo kratkega dosega (NFC) in elektronskim nadzorom blaga (EAS), ki delujejo v območjih nizke in visoke frekvence.
Ta dokument obravnava tudi fiksne, mobilne in prenosne postaje.
OPOMBA: Če sistem vključuje transponderje, se ti izmerijo skupaj z oddajnikom.

General Information

• Status: Published
• Public Enquiry End Date: 31-Jul-2016
• Publication Date: 27-Feb-2017
• ICS: 33.060.20 - Receiving and transmitting equipment
• ICS: 33.100.01 - Electromagnetic compatibility in general
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 13-Feb-2017
• Due Date: 20-Apr-2017
• Completion Date: 28-Feb-2017
• Directive: 1999/5/EC - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Ref Project: ETSI EN 300 330 V2.1.1 (2017-02) - Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 300 330 V2.1.1:2017
01-april-2017
1DSUDYHNUDWNHJDGRVHJD65'5DGLMVNDRSUHPDYIUHNYHQþQHPREPRþMXRG
N+]GR0+]LQVLVWHPL]LQGXNFLMVNR]DQNRYIUHNYHQþQHPREPRþMXRGN+]GR
0+]+DUPRQL]LUDQLVWDQGDUGNL]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH
(8
6KRUW5DQJH'HYLFHV65'5DGLRHTXLSPHQWLQWKHIUHTXHQF\UDQJHN+]WR0+]
DQGLQGXFWLYHORRSV\VWHPVLQWKHIUHTXHQF\UDQJHN+]WR0+]
+DUPRQLVHG6WDQGDUGFRYHULQJWKHHVVHQWLDOUHTXLUHPHQWVRIDUWLFOHRIWKH'LUHFWLYH
(8
Ta slovenski standard je istoveten z: ETSI EN 300 330 V2.1.1 (2017-02)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 300 330 V2.1.1:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 300 330 V2.1.1:2017

---------------------- Page: 2 ----------------------

SIST EN 300 330 V2.1.1:2017
ETSI EN 300 330 V2.1.1 (2017-02)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Radio equipment in the frequency range
9 kHz to 25 MHz and inductive loop systems
in the frequency range 9 kHz to 30 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU

---------------------- Page: 3 ----------------------

SIST EN 300 330 V2.1.1:2017
 2 ETSI EN 300 330 V2.1.1 (2017-02)



Reference
REN/ERM-TG28-507
Keywords
harmonised standard, radio, RFID, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2017.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 300 330 V2.1.1:2017
 3 ETSI EN 300 330 V2.1.1 (2017-02)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 9
1 Scope . 10
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 Environmental conditions . 14
4.2 General . 14
4.2.1 General performance criteria . 14
4.2.2 Presentation of equipment for testing purposes . 14
4.2.2.0 General . 14
4.2.2.1 Choice of model for testing . 15
4.2.2.2 Testing of equipment with alternative radiated H-field strengths . 15
4.2.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 15
4.2.2.3.1 Equipment with an internal permanent or temporary antenna connector . 15
4.2.2.3.2 Equipment with a temporary antenna connector . 15
4.2.2.4 On-site testing . 16
4.2.3 Mechanical and electrical design . 16
4.2.3.1 General . 16
4.2.3.2 Controls . 16
4.2.3.3 Transmitter shut-off facility . 16
4.2.3.4 Receiver mute or squelch . 16
4.3 Transmitter conformance requirements . 16
4.3.1 Permitted range of operating frequencies . 16
4.3.1.1 Applicability. 16
4.3.1.2 Description . 16
4.3.1.3 Limits . 16
4.3.1.4 Conformance . 16
4.3.2 Operating frequency ranges . 16
4.3.2.1 Applicability. 16
4.3.2.2 Description . 17
4.3.2.3 Limits . 17
4.3.2.4 Conformance . 17
4.3.3 Modulation bandwidth . 17
4.3.3.1 Applicability. 17
4.3.3.2 Description . 17
4.3.3.3 Limits . 17
4.3.3.4 Conformance . 17
4.3.4 Transmitter H-field requirements . 18
4.3.4.1 Applicability. 18
4.3.4.2 Description . 18
4.3.4.3 Limits . 18
4.3.4.4 Conformance . 19
4.3.5 Transmitter RF carrier current . 19
4.3.5.1 Applicability. 19
4.3.5.2 Description . 19
ETSI

---------------------- Page: 5 ----------------------

SIST EN 300 330 V2.1.1:2017
 4 ETSI EN 300 330 V2.1.1 (2017-02)
4.3.5.3 Limits . 19
4.3.5.4 Conformance . 20
4.3.6 Transmitter radiated E-field . 20
4.3.6.1 Applicability. 20
4.3.6.2 Description . 20
4.3.6.3 Limits . 20
4.3.6.4 Conformance . 20
4.3.7 Transmitter conducted spurious emissions . 20
4.3.7.1 Applicability. 20
4.3.7.2 Description . 20
4.3.7.3 Limits . 21
4.3.7.4 Conformance . 21
4.3.8 Transmitter radiated spurious domain emission limits < 30 MHz . 21
4.3.8.1 Applicability. 21
4.3.8.2 Description . 21
4.3.8.3 Limits . 21
4.3.8.4 Conformance . 21
4.3.9 Transmitter radiated spurious domain emission limits > 30 MHz . 21
4.3.9.1 Applicability. 21
4.3.9.2 Description . 22
4.3.9.3 Limits . 22
4.3.9.4 Conformance . 22
4.3.10 Transmitter Frequency stability . 22
4.3.10.1 Applicability. 22
4.3.10.2 Description . 22
4.3.10.3 Limits . 22
4.3.10.4 Conformance . 22
4.4 Receiver Conformance requirements . 23
4.4.1 General . 23
4.4.2 Receiver spurious emissions . 23
4.4.2.1 Applicability. 23
4.4.2.2 Description . 23
4.4.2.3 Limits . 23
4.4.2.4 Conformance . 23
4.4.3 Adjacent channel selectivity . 24
4.4.3.1 Applicability. 24
4.4.3.2 Description . 24
4.4.3.3 Limits . 24
4.4.3.4 Conformance . 24
4.4.4 Receiver blocking or desensitization . 24
4.4.4.1 Applicability. 24
4.4.4.2 Description . 24
4.4.4.3 Limits . 25
4.4.4.4 Conformance . 25
5 Testing for compliance with technical requirements . 25
5.1 Environmental conditions for testing . 25
5.2 General conditions for testing . 25
5.2.1 Product information . 25
5.3 Normal and extreme test conditions . 25
5.4 Test power source . 26
5.4.0 General . 26
5.4.1 External test power source . 26
5.4.2 Internal test power source . 26
5.5 Normal test conditions . 26
5.5.1 Normal temperature and humidity . 26
5.5.2 Normal test power source . 26
5.5.2.1 Mains voltage . 26
5.5.2.2 Regulated lead-acid battery power sources . 27
5.5.2.3 Other power sources . 27
5.6 Extreme test conditions . 27
5.6.1 Extreme temperatures . 27
ETSI

---------------------- Page: 6 ----------------------

SIST EN 300 330 V2.1.1:2017
 5 ETSI EN 300 330 V2.1.1 (2017-02)
5.6.1.1 Procedure for tests at extreme temperatures . 27
5.6.1.1.0 General . 27
5.6.1.1.1 Procedure for equipment designed for continuous operation . 27
5.6.1.1.2 Procedure for equipment designed for intermittent operation . 27
5.6.1.2 Extreme temperature ranges . 28
5.6.2 Extreme test source voltages . 28
5.6.2.1 Mains voltage . 28
5.6.2.2 Regulated lead-acid battery power sources . 28
5.6.2.3 Power sources using other types of batteries . 28
5.6.2.4 Other power sources . 28
5.7 Auxiliary test equipment . 29
5.8 Normal test signals and test modulation . 29
5.8.0 General . 29
5.8.1 Normal test signals for analogue speech . 29
5.8.2 Normal test signals for data . 29
5.9 Artificial antenna . 29
5.9.0 General . 29
5.9.1 Artificial antenna for inductive transmitters (non 50 Ω) . 29
5.9.2 Artificial antenna for transmitters with 50 Ω impedance connector . 30
5.10 Test fixture . 30
5.11 Test sites and general arrangements for radiated measurements . 31
5.12 Measuring receiver . 31
5.13 Measurement uncertainty . 31
5.14 Interpretation of the measurement results . 32
5.14.0 General . 32
5.14.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 32
6 Conformance methods of measurement for transmitters and receivers . 32
6.1 Transmitter requirements . 32
6.1.1 Transmitter definitions . 32
6.1.2 Equipment Product Classes . 33
6.1.3 Modes of operation of the transmitter . 33
6.2 Conformance methods of measurement for transmitter . 33
6.2.1 General . 33
6.2.2 Operating frequency ranges . 33
6.2.2.1 General . 33
6.2.2.2 OFR measurement with spectrum analyser . 34
6.2.3 Modulation bandwidth . 34
6.2.4 Transmitter H-field . 35
6.2.5 Transmitter RF carrier current . 35
6.2.6 Transmitter radiated E-field . 35
6.2.7 Transmitter conducted spurious emissions . 35
6.2.7.1 Transmitter conducted spurious emissions < 30 MHz . 35
6.2.7.2 Transmitter conducted spurious emissions ≥ 30 MHz . 36
6.2.8 Transmitter radiated spurious domain emission limits < 30 MHz . 36
6.2.9 Transmitter radiated spurious domain emission limits > 30 MHz . 36
6.2.10 Transmitter Frequency stability under low voltage conditions . 37
6.2.10.1 Test conditions . 37
6.3 Conformance methods of measurement for receiver . 37
6.3.1 Receiver spurious emissions .
...

ETSI EN 300 330 V2.1.1 (2017-02)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Radio equipment in the frequency range
9 kHz to 25 MHz and inductive loop systems
in the frequency range 9 kHz to 30 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 ETSI EN 300 330 V2.1.1 (2017-02)



Reference
REN/ERM-TG28-507
Keywords
harmonised standard, radio, RFID, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2017.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 300 330 V2.1.1 (2017-02)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 9
1 Scope . 10
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 Environmental conditions . 14
4.2 General . 14
4.2.1 General performance criteria . 14
4.2.2 Presentation of equipment for testing purposes . 14
4.2.2.0 General . 14
4.2.2.1 Choice of model for testing . 15
4.2.2.2 Testing of equipment with alternative radiated H-field strengths . 15
4.2.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 15
4.2.2.3.1 Equipment with an internal permanent or temporary antenna connector . 15
4.2.2.3.2 Equipment with a temporary antenna connector . 15
4.2.2.4 On-site testing . 16
4.2.3 Mechanical and electrical design . 16
4.2.3.1 General . 16
4.2.3.2 Controls . 16
4.2.3.3 Transmitter shut-off facility . 16
4.2.3.4 Receiver mute or squelch . 16
4.3 Transmitter conformance requirements . 16
4.3.1 Permitted range of operating frequencies . 16
4.3.1.1 Applicability. 16
4.3.1.2 Description . 16
4.3.1.3 Limits . 16
4.3.1.4 Conformance . 16
4.3.2 Operating frequency ranges . 16
4.3.2.1 Applicability. 16
4.3.2.2 Description . 17
4.3.2.3 Limits . 17
4.3.2.4 Conformance . 17
4.3.3 Modulation bandwidth . 17
4.3.3.1 Applicability. 17
4.3.3.2 Description . 17
4.3.3.3 Limits . 17
4.3.3.4 Conformance . 17
4.3.4 Transmitter H-field requirements . 18
4.3.4.1 Applicability. 18
4.3.4.2 Description . 18
4.3.4.3 Limits . 18
4.3.4.4 Conformance . 19
4.3.5 Transmitter RF carrier current . 19
4.3.5.1 Applicability. 19
4.3.5.2 Description . 19
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 300 330 V2.1.1 (2017-02)
4.3.5.3 Limits . 19
4.3.5.4 Conformance . 20
4.3.6 Transmitter radiated E-field . 20
4.3.6.1 Applicability. 20
4.3.6.2 Description . 20
4.3.6.3 Limits . 20
4.3.6.4 Conformance . 20
4.3.7 Transmitter conducted spurious emissions . 20
4.3.7.1 Applicability. 20
4.3.7.2 Description . 20
4.3.7.3 Limits . 21
4.3.7.4 Conformance . 21
4.3.8 Transmitter radiated spurious domain emission limits < 30 MHz . 21
4.3.8.1 Applicability. 21
4.3.8.2 Description . 21
4.3.8.3 Limits . 21
4.3.8.4 Conformance . 21
4.3.9 Transmitter radiated spurious domain emission limits > 30 MHz . 21
4.3.9.1 Applicability. 21
4.3.9.2 Description . 22
4.3.9.3 Limits . 22
4.3.9.4 Conformance . 22
4.3.10 Transmitter Frequency stability . 22
4.3.10.1 Applicability. 22
4.3.10.2 Description . 22
4.3.10.3 Limits . 22
4.3.10.4 Conformance . 22
4.4 Receiver Conformance requirements . 23
4.4.1 General . 23
4.4.2 Receiver spurious emissions . 23
4.4.2.1 Applicability. 23
4.4.2.2 Description . 23
4.4.2.3 Limits . 23
4.4.2.4 Conformance . 23
4.4.3 Adjacent channel selectivity . 24
4.4.3.1 Applicability. 24
4.4.3.2 Description . 24
4.4.3.3 Limits . 24
4.4.3.4 Conformance . 24
4.4.4 Receiver blocking or desensitization . 24
4.4.4.1 Applicability. 24
4.4.4.2 Description . 24
4.4.4.3 Limits . 25
4.4.4.4 Conformance . 25
5 Testing for compliance with technical requirements . 25
5.1 Environmental conditions for testing . 25
5.2 General conditions for testing . 25
5.2.1 Product information . 25
5.3 Normal and extreme test conditions . 25
5.4 Test power source . 26
5.4.0 General . 26
5.4.1 External test power source . 26
5.4.2 Internal test power source . 26
5.5 Normal test conditions . 26
5.5.1 Normal temperature and humidity . 26
5.5.2 Normal test power source . 26
5.5.2.1 Mains voltage . 26
5.5.2.2 Regulated lead-acid battery power sources . 27
5.5.2.3 Other power sources . 27
5.6 Extreme test conditions . 27
5.6.1 Extreme temperatures . 27
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 300 330 V2.1.1 (2017-02)
5.6.1.1 Procedure for tests at extreme temperatures . 27
5.6.1.1.0 General . 27
5.6.1.1.1 Procedure for equipment designed for continuous operation . 27
5.6.1.1.2 Procedure for equipment designed for intermittent operation . 27
5.6.1.2 Extreme temperature ranges . 28
5.6.2 Extreme test source voltages . 28
5.6.2.1 Mains voltage . 28
5.6.2.2 Regulated lead-acid battery power sources . 28
5.6.2.3 Power sources using other types of batteries . 28
5.6.2.4 Other power sources . 28
5.7 Auxiliary test equipment . 29
5.8 Normal test signals and test modulation . 29
5.8.0 General . 29
5.8.1 Normal test signals for analogue speech . 29
5.8.2 Normal test signals for data . 29
5.9 Artificial antenna . 29
5.9.0 General . 29
5.9.1 Artificial antenna for inductive transmitters (non 50 Ω) . 29
5.9.2 Artificial antenna for transmitters with 50 Ω impedance connector . 30
5.10 Test fixture . 30
5.11 Test sites and general arrangements for radiated measurements . 31
5.12 Measuring receiver . 31
5.13 Measurement uncertainty . 31
5.14 Interpretation of the measurement results . 32
5.14.0 General . 32
5.14.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 32
6 Conformance methods of measurement for transmitters and receivers . 32
6.1 Transmitter requirements . 32
6.1.1 Transmitter definitions . 32
6.1.2 Equipment Product Classes . 33
6.1.3 Modes of operation of the transmitter . 33
6.2 Conformance methods of measurement for transmitter . 33
6.2.1 General . 33
6.2.2 Operating frequency ranges . 33
6.2.2.1 General . 33
6.2.2.2 OFR measurement with spectrum analyser . 34
6.2.3 Modulation bandwidth . 34
6.2.4 Transmitter H-field . 35
6.2.5 Transmitter RF carrier current . 35
6.2.6 Transmitter radiated E-field . 35
6.2.7 Transmitter conducted spurious emissions . 35
6.2.7.1 Transmitter conducted spurious emissions < 30 MHz . 35
6.2.7.2 Transmitter conducted spurious emissions ≥ 30 MHz . 36
6.2.8 Transmitter radiated spurious domain emission limits < 30 MHz . 36
6.2.9 Transmitter radiated spurious domain emission limits > 30 MHz . 36
6.2.10 Transmitter Frequency stability under low voltage conditions . 37
6.2.10.1 Test conditions . 37
6.3 Conformance methods of measurement for receiver . 37
6.3.1 Receiver spurious emissions . 37
6.3.2 Adjacent channel selectivity . 38
6.3.3 Receiver blocking or desensitization . 38
6.3.3.1 Measurement for channelized, narrowband or broadband equipment . 38
6.3.3.2 Measurement for tagging systems . 39
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 40
Annex B (normative): Transmitter definitions . 42
B.1 Transmitter definitions . 42
B.1.0 General .
...

Final draft ETSI EN 300 330 V2.1.1 (2016-11)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Radio equipment in the frequency range
9 kHz to 25 MHz and inductive loop systems
in the frequency range 9 kHz to 30 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 330 V2.1.1 (2016-11)



Reference
REN/ERM-TG28-507
Keywords
harmonised standard, radio, RFID, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 330 V2.1.1 (2016-11)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 10
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 Environmental conditions . 14
4.2 General . 14
4.2.1 General performance criteria . 14
4.2.2 Presentation of equipment for testing purposes . 14
4.2.2.0 General . 14
4.2.2.1 Choice of model for testing . 15
4.2.2.2 Testing of equipment with alternative radiated H-field strengths . 15
4.2.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 15
4.2.2.3.1 Equipment with an internal permanent or temporary antenna connector . 15
4.2.2.3.2 Equipment with a temporary antenna connector . 15
4.2.2.4 On-site testing . 16
4.2.3 Mechanical and electrical design . 16
4.2.3.1 General . 16
4.2.3.2 Controls . 16
4.2.3.3 Transmitter shut-off facility . 16
4.2.3.4 Receiver mute or squelch . 16
4.3 Transmitter conformance requirements . 16
4.3.1 Permitted range of operating frequencies . 16
4.3.1.1 Applicability. 16
4.3.1.2 Description . 16
4.3.1.3 Limits . 16
4.3.1.4 Conformance . 16
4.3.2 Operating frequency ranges . 16
4.3.2.1 Applicability. 16
4.3.2.2 Description . 17
4.3.2.3 Limits . 17
4.3.2.4 Conformance . 17
4.3.3 Modulation bandwidth . 17
4.3.3.1 Applicability. 17
4.3.3.2 Description . 17
4.3.3.3 Limits . 17
4.3.3.4 Conformance . 17
4.3.4 Transmitter H-field requirements . 18
4.3.4.1 Applicability. 18
4.3.4.2 Description . 18
4.3.4.3 Limits . 18
4.3.4.4 Conformance . 19
4.3.5 Transmitter RF carrier current . 19
4.3.5.1 Applicability. 19
4.3.5.2 Description . 19
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 330 V2.1.1 (2016-11)
4.3.5.3 Limits . 19
4.3.5.4 Conformance . 20
4.3.6 Transmitter radiated E-field . 20
4.3.6.1 Applicability. 20
4.3.6.2 Description . 20
4.3.6.3 Limits . 20
4.3.6.4 Conformance . 20
4.3.7 Transmitter conducted spurious emissions . 20
4.3.7.1 Applicability. 20
4.3.7.2 Description . 20
4.3.7.3 Limits . 21
4.3.7.4 Conformance . 21
4.3.8 Transmitter radiated spurious domain emission limits < 30 MHz . 21
4.3.8.1 Applicability. 21
4.3.8.2 Description . 21
4.3.8.3 Limits . 21
4.3.8.4 Conformance . 21
4.3.9 Transmitter radiated spurious domain emission limits > 30 MHz . 21
4.3.9.1 Applicability. 21
4.3.9.2 Description . 22
4.3.9.3 Limits . 22
4.3.9.4 Conformance . 22
4.3.10 Transmitter Frequency stability . 22
4.3.10.1 Applicability. 22
4.3.10.2 Description . 22
4.3.10.3 Limits . 22
4.3.10.4 Conformance . 22
4.4 Receiver Conformance requirements . 23
4.4.1 General . 23
4.4.2 Receiver spurious emissions . 23
4.4.2.1 Applicability. 23
4.4.2.2 Description . 23
4.4.2.3 Limits . 23
4.4.2.4 Conformance . 23
4.4.3 Adjacent channel selectivity . 24
4.4.3.1 Applicability. 24
4.4.3.2 Description . 24
4.4.3.3 Limits . 24
4.4.3.4 Conformance . 24
4.4.4 Receiver blocking or desensitization . 24
4.4.4.1 Applicability. 24
4.4.4.2 Description . 24
4.4.4.3 Limits . 25
4.4.4.4 Conformance . 25
5 Testing for compliance with technical requirements . 25
5.1 Environmental conditions for testing . 25
5.2 General conditions for testing . 25
5.2.1 Product information . 25
5.3 Normal and extreme test conditions . 25
5.4 Test power source . 26
5.4.0 General . 26
5.4.1 External test power source . 26
5.4.2 Internal test power source . 26
5.5 Normal test conditions . 26
5.5.1 Normal temperature and humidity . 26
5.5.2 Normal test power source . 26
5.5.2.1 Mains voltage . 26
5.5.2.2 Regulated lead-acid battery power sources . 27
5.5.2.3 Other power sources . 27
5.6 Extreme test conditions . 27
5.6.1 Extreme temperatures . 27
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 330 V2.1.1 (2016-11)
5.6.1.1 Procedure for tests at extreme temperatures . 27
5.6.1.1.0 General . 27
5.6.1.1.1 Procedure for equipment designed for continuous operation . 27
5.6.1.1.2 Procedure for equipment designed for intermittent operation . 27
5.6.1.2 Extreme temperature ranges . 28
5.6.2 Extreme test source voltages . 28
5.6.2.1 Mains voltage . 28
5.6.2.2 Regulated lead-acid battery power sources . 28
5.6.2.3 Power sources using other types of batteries . 28
5.6.2.4 Other power sources . 28
5.7 Auxiliary test equipment . 29
5.8 Normal test signals and test modulation . 29
5.8.0 General . 29
5.8.1 Normal test signals for analogue speech . 29
5.8.2 Normal test signals for data . 29
5.9 Artificial antenna . 29
5.9.0 General . 29
5.9.1 Artificial antenna for inductive transmitters (non 50 Ω) . 29
5.9.2 Artificial antenna for transmitters with 50 Ω impedance connector . 30
5.10 Test fixture . 30
5.11 Test sites and general arrangements for radiated measurements . 31
5.12 Measuring receiver . 31
5.13 Measurement uncertainty . 31
5.14 Interpretation of the measurement results . 32
5.14.0 General . 32
5.14.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 32
6 Conformance methods of measurement for transmitters and receivers . 32
6.1 Transmitter requirements . 32
6.1.1 Transmitter definitions . 32
6.1.2 Equipment Product Classes . 33
6.1.3 Modes of operation of the transmitter . 33
6.2 Conformance methods of measurement for transmitter . 33
6.2.1 General . 33
6.2.2 Operating frequency ranges . 33
6.2.2.1 General . 33
6.2.2.2 OFR measurement with spectrum analyser . 34
6.2.3 Modulation bandwidth . 34
6.2.4 Transmitter H-field . 35
6.2.5 Transmitter RF carrier current . 35
6.2.6 Transmitter radiated E-field . 35
6.2.7 Transmitter conducted spurious emissions . 35
6.2.7.1 Transmitter conducted spurious emissions < 30 MHz . 35
6.2.7.2 Transmitter conducted spurious emissions ≥ 30 MHz . 36
6.2.8 Transmitter radiated spurious domain emission limits < 30 MHz . 36
6.2.9 Transmitter radiated spurious domain emission limits > 30 MHz . 36
6.2.10 Transmitter Frequency stability under low voltage conditions . 37
6.2.10.1 Test conditions . 37
6.3 Conformance methods of measurement for receiver . 37
6.3.1 Receiver spurious emissions . 37
6.3.2 Adjacent channel selectivity . 38
6.3.3 Receiver blocking or desensitization . 38
6.3.3.1 Measurement for channelized, narrowband or broadband equipment . 38
6.3.3.2 Measurement for tagging systems . 39
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 40
Annex B (normative): Transmitter definitions . 42
B.1 Transmitter definitions . 42
B.1.0 General .
...

Draft ETSI EN 300 330 V2.1.0 (2016-05)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD);
Radio equipment in the frequency range
9 kHz to 25 MHz and inductive loop systems
in the frequency range 9 kHz to 30 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 330 V2.1.0 (2016-05)



Reference
REN/ERM-TG28-507
Keywords
harmonised standard, radio, RFID, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 330 V2.1.0 (2016-05)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 12
3.3 Abbreviations . 12
4 Technical requirements . 13
4.1 Environmental conditions . 13
4.2 General . 13
4.2.1 General performance criteria . 13
4.2.2 Presentation of equipment for testing purposes . 13
4.2.2.0 General . 13
4.2.2.1 Choice of model for testing . 14
4.2.2.2 Testing of equipment with alternative radiated H-field strengths . 14
4.2.2.3 Testing of equipment that does not have an external 50 Ω RF connector (integral antenna
equipment) . 14
4.2.2.3.1 Equipment with an internal permanent or temporary antenna connector . 14
4.2.2.3.2 Equipment with a temporary antenna connector . 14
4.2.2.4 On-site testing . 14
4.2.3 Mechanical and electrical design . 14
4.2.3.1 General . 14
4.2.3.2 Controls . 14
4.2.3.3 Transmitter shut-off facility . 15
4.2.3.4 Receiver mute or squelch . 15
4.2.3.5 Marking (equipment identification) . 15
4.3 Transmitter conformance requirements . 15
4.3.1 Transmitter requirements . 15
4.3.2 Permitted range of operating frequencies . 15
4.3.2.1 Applicability. 15
4.3.2.2 Description . 15
4.3.2.3 Limits . 15
4.3.2.4 Conformance . 16
4.3.3 Operating frequency ranges . 16
4.3.3.1 Applicability. 16
4.3.3.2 Description . 16
4.3.3.3 Limits . 16
4.3.3.4 Conformance . 16
4.3.4 Operating frequency range of the modulation bandwidth . 16
4.3.4.1 Applicability. 16
4.3.4.2 Description . 16
4.3.4.3 Limits . 16
4.3.4.4 Conformance . 17
4.3.5 Transmitter H-field requirements . 17
4.3.5.1 Applicability. 17
4.3.5.2 Description . 17
4.3.5.3 Limits . 17
4.3.5.4 Conformance . 18
4.3.6 Transmitter RF carrier current . 18
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 330 V2.1.0 (2016-05)
4.3.6.1 Applicability. 18
4.3.6.2 Description . 18
4.3.6.3 Limits . 18
4.3.6.4 Conformance . 19
4.3.7 Transmitter radiated E-field . 19
4.3.7.1 Applicability. 19
4.3.7.2 Description . 19
4.3.7.3 Limits . 19
4.3.7.4 Conformance . 19
4.3.8 Transmitter conducted spurious emissions . 19
4.3.8.1 Applicability. 19
4.3.8.2 Description . 19
4.3.8.3 Limits . 20
4.3.8.4 Conformance . 20
4.3.9 Transmitter radiated spurious domain emission limits < 30 MHz . 20
4.3.9.1 Applicability. 20
4.3.9.2 Description . 20
4.3.9.3 Limits . 20
4.3.9.4 Conformance . 20
4.3.10 Transmitter radiated spurious domain emission limits > 30 MHz . 21
4.3.10.1 Applicability. 21
4.3.10.2 Description . 21
4.3.10.3 Limits . 21
4.3.10.4 Conformance . 21
4.3.11 Transmitter Frequency stability . 21
4.3.11.1 Applicability. 21
4.3.11.2 Description . 21
4.3.11.3 Limits . 21
4.3.11.4 Conformance . 22
4.4 Receiver Conformance requirements . 22
4.4.1 General . 22
4.4.2 Receiver spurious emissions . 22
4.4.2.1 Applicability. 22
4.4.2.2 Description . 22
4.4.2.3 Limits . 22
4.4.2.4 Conformance . 22
4.4.3 Adjacent channel selectivity . 23
4.4.3.1 Applicability. 23
4.4.3.2 Description . 23
4.4.3.3 Limits . 23
4.4.3.4 Conformance . 23
4.4.4 Receiver blocking or desensitization . 23
4.4.4.1 Applicability. 23
4.4.4.2 Description . 23
4.4.4.3 Limits . 23
4.4.4.4 Conformance . 24
5 Testing for compliance with technical requirements . 24
5.1 Environmental conditions for testing . 24
5.2 General conditions for testing . 24
5.2.1 Product information . 24
5.3 Normal and extreme test conditions . 24
5.4 Test power source . 24
5.4.0 General . 24
5.4.1 External test power source . 25
5.4.2 Internal test power source . 25
5.5 Normal test conditions . 25
5.5.1 Normal temperature and humidity . 25
5.5.2 Normal test power source . 25
5.5.2.1 Mains voltage . 25
5.5.2.2 Regulated lead-acid battery power sources . 25
5.5.2.3 Other power sources . 25
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 330 V2.1.0 (2016-05)
5.6 Extreme test conditions . 26
5.6.1 Extreme temperatures . 26
5.6.1.1 Procedure for tests at extreme temperatures . 26
5.6.1.1.0 General . 26
5.6.1.1.1 Procedure for equipment designed for continuous operation . 26
5.6.1.1.2 Procedure for equipment designed for intermittent operation . 26
5.6.1.2 Extreme temperature ranges . 26
5.6.2 Extreme test source voltages . 27
5.6.2.1 Mains voltage . 27
5.6.2.2 Regulated lead-acid battery power sources . 27
5.6.2.3 Power sources using other types of batteries . 27
5.6.2.4 Other power sources . 27
5.7 Auxiliary test equipment . 27
5.8 Normal test signals and test modulation . 27
5.8.0 General . 27
5.8.1 Normal test signals for analogue speech . 27
5.8.2 Normal test signals for data . 28
5.9 Artificial antenna . 28
5.9.0 General . 28
5.9.1 Artificial antenna for inductive transmitters (non 50 Ω) . 28
5.9.2 Artificial antenna for transmitters with 50 Ω impedance connector . 28
5.10 Test fixture . 29
5.11 Test sites and general arrangements for radiated measurements . 29
5.12 Measuring receiver . 29
5.13 Measurement uncertainty . 30
5.14 Interpretation of the measurement results . 30
5.14.0 General . 30
5.14.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty . 30
6 Conformance methods of measurement for transmitters . 31
6.1 Transmitter requirements . 31
6.1.0 General . 31
6.1.1 Transmitter definitions . 31
6.1.2 Equipment Product Classes . 31
6.1.3 Modes of operation of the transmitter . 32
6.2 Conformance methods of measurement for transmitter . 32
6.2.1 General . 32
6.2.2 Operating frequency ranges . 32
6.2.3 Operating frequency ranges of the modulation bandwidth . 33
6.2.4 Transmitter H-field . 33
6.2.5 Transmitter RF carrier current . 33
6.2.6 Transmitter radiated E-field . 34
6.2.7 Transmitter conducted spurious emissions . 34
6.2.7.1 Transmitter conducted spurious emissions < 30 MHz . 34
6.2.7.2 Transmitter conducted spurious emissions ≥ 30 MHz . 34
6.2.8 Transmitter radiated spurious domain emission limits < 30 MHz . 34
6.2.9 Transmitter radiated spurious domain emission limits > 30 MHz . 35
6.2.10 Transmitter Frequency stability under low voltage conditions . 35
6.2.10.1 Test conditions . 35
6.2.10.2 Measurement procedure . 35
7 Conformance methods of measurement for receiver . 36
7.1 General . 36
7.2 Receiver spurious emissions. 36
7.3 Adjacent channel selectivity . 36
7.4 Receiver blocking or desensitization . 36
7.4.1 Measurement for channelized, narrowband or broadband equipment . 36
7.4.2 Measurement for tagging systems . 37
Annex A (normative): Relationship between the present d
...