SIST EN 13361:2013
(Main)Geosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams
Geosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams
This European Standard specifies the relevant characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, to be used as fluid barriers for potable, fresh or saline water, in the construction of reservoirs and dams, and the appropriate test methods to determine these characteristics. The intended use of these products is to control the leakage of water through the construction. This European Standard is not applicable to geotextiles or geotextile-related products. This European Standard provides for the evaluation of conformity of the product to this document. This European Standard defines requirements to be met by manufacturers and their authorised representatives with regard to the presentation of product properties. This European Standard does not cover applications where the geosynthetic barrier is to be in contact with water that has been treated for human consumption. Where potable water is or may be in direct contact with the product the designer should also refer to other relevant standards, requirements and/or regulations.
Geosynthetische Dichtungsbahnen - Eigenschaften, die für die Anwendung beim Bau von Rückhaltebecken und Staudämmen erforderlich sind
Diese Europäische Norm legt die relevanten Eigenschaften von geosynthetischen Dichtungsbahnen, einschließlich geosynthetischer Kunststoffdichtungsbahnen, geosynthetischer Tondichtungsbahnen und geosynthetischer Bitumendichtungsbahnen, die als Abdichtung für Trink-, Süß- oder Salzwasser beim Bau von Rückhaltebecken und Staudämmen verwendet werden, und die geeigneten Prüfverfahren zur Bestimmung dieser Eigenschaften fest.
Die bestimmungsgemäße Anwendung dieser Produkte ist das Durchsickern von Wasser durch das Bauwerk zu kontrollieren.
Diese Europäische Norm ist nicht anwendbar auf Geotextilien oder geotextilverwandte Produkte.
Diese Europäische Norm ermöglicht die Konformitätsbewertung des Produktes hinsichtlich dieses Dokuments.
Diese Europäische Norm legt die Anforderungen fest, die von den Herstellern und ihren autorisierten Vertretern in Bezug auf die Darstellung der Produkteigenschaften eingehalten werden müssen.
Diese Europäische Norm umfasst nicht die Anwendungen, bei denen die geosynthetische Dichtungsbahn in Kontakt mit Wasser kommt, das für den unmittelbaren menschlichen Gebrauch behandelt wurde.
Wo Trinkwasser in direkten Kontakt mit dem Produkt kommt oder kommen kann, muss sich der Planer auf andere zutreffende Normen, Anforderungen und/oder Bestimmungen beziehen
Géomembranes, géosynthétiques bentonitiques - Caractéristiques requises pour l'utilisation dans la construction des réservoirs et des barrages
La présente Norme européenne spécifie les caractéristiques requises pour les géomembranes polymériques ou bitumineuses et les géosynthétiques bentonitiques utilisés comme barrière aux fluides, eau potable, douce ou saline dans la structure des réservoirs et barrages, ainsi que les méthodes d'essai appropriées pour déterminer ces caractéristiques.
Ces produits sont destinés à contrôler les fuites d'eau à travers la construction.
La présente Norme européenne ne s'applique pas aux géotextiles ou produits apparentés.
Elle donne les informations permettant d'évaluer la conformité du produit au présent document.
La présente Norme européenne définit les exigences auxquelles les fabricants et leurs représentants agréés doivent satisfaire pour la présentation des propriétés du produit.
Elle ne couvre pas les cas où la géomembrane ou le géosynthétique bentonitique doit être en contact avec une eau traitée destinée à la consommation humaine.
Si de l'eau potable est ou peut être en contact direct avec le produit, il convient que le concepteur se réfère également aux normes, exigences et/ou règlements applicables.
Geosintetične ovire - Zahtevane karakteristike pri gradnji rezervoarjev in nasipov
Ta evropski standard določa ustrezne lastnosti geosintetičnih ovir, vključno s polimernimi, opečnati in bitumenskimi geosintetičnimi ovirami, ki se uporabljajo za zaščito pred tekočinami za pitno, sladko ali slano vodo, pri gradnji zbiralnikov in jezov, in ustrezne preskusne metode za določanje teh lastnosti. Ti proizvodi se predvidoma uporabljajo za nadzor uhajanja vode skozi konstrukcijo. Ta evropski standard ne velja za geotekstilije ali sorodne izdelke. Ta evropski standard omogoča vrednotenje skladnosti izdelka s tem dokumentom. Ta evropski standard določa zahteve, ki jih morajo izpolniti proizvajalci in njihovi pooblaščeni zastopniki glede predstavitve lastnosti izdelka. Ta evropski standard ne zajema uporabe, kjer bodo geosintetične ovire v stiku s pitno vodo, ki je namenjena ljudem. Če je oz. bo lahko proizvod v stiku s pitno vodo, mora projektant upoštevati tudi druge ustrezne standarde, zahteve in/ali predpise.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Geosynthetische Dichtungsbahnen - Eigenschaften, die für die Anwendung beim Bau von Rückhaltebecken und Staudämmen erforderlich sindGéomembranes, géosynthétiques bentonitiques - Caractéristiques requises pour l'utilisation dans la construction des réservoirs et des barragesGeosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams91.100.50Veziva. Tesnilni materialiBinders. Sealing materials59.080.70GeotekstilijeGeotextilesICS:Ta slovenski standard je istoveten z:EN 13361:2013SIST EN 13361:2013en,fr,de01-december-2013SIST EN 13361:2013SLOVENSKI
STANDARDSIST EN 13361:2004/A1:2007SIST EN 13361:20041DGRPHãþD
SIST EN 13361:2013
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13361
July 2013 ICS 59.080.70; 91.100.50 Supersedes EN 13361:2004English Version
Geosynthetic barriers - Characteristics required for use in the construction of reservoirs and dams
Géomembranes, géosynthétiques bentonitiques - Caractéristiques requises pour l'utilisation dans la construction des réservoirs et des barrages
Geosynthetische Dichtungsbahnen - Eigenschaften, die für die Anwendung beim Bau von Rückhaltebecken und Staudämmen erforderlich sind This European Standard was approved by CEN on 23 May 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13361:2013: ESIST EN 13361:2013
EN 13361:2013 (E) 2 Contents Page Foreword .4 Introduction .5 1 Scope .6 2 Normative references .6 3 Terms, definitions and abbreviations .8 3.1 Terms and definitions .8 3.2 Abbreviations .9 4 Required characteristics and corresponding methods of test .9 4.1 General .9 4.2 Types of application .9 4.2.1 General .9 4.2.2 Application 1: "covered in service" .9 4.2.3 Application 2: "not covered in service" . 12 4.3 Relevant characteristics . 13 4.4 Characteristics relevant to specific conditions of use . 18 4.4.1 General . 18 4.4.2 Tear strength . 18 4.4.3 Burst strength . 18 4.4.4 Friction characteristics (direct shear and inclined plane tests). . 18 4.4.5 Low temperature behaviour . 18 4.4.6 Weathering . 18 4.4.7 Resistance to wetting and drying . 19 4.4.8 Freeze-thaw cycle resistance . 19 4.4.9 Resistance to root penetration . 19 4.4.10 Chemical resistance . 19 4.5 Release of dangerous substances . 19 5 Evaluation of conformity . 19 5.1 Presentation of characteristics . 19 5.2 Verification of values . 19 5.3 Initial type tests . 20 5.4 Factory production control . 20 5.5 Inspection . 21 6 Marking . 21 Annex A (normative)
Factory production control — Factory production control scheme . 22 A.1 General . 22 A.2 Product design . 22 A.3 Production . 22 A.3.1 Raw or incoming materials . 22 A.3.2 Production process . 22 A.4 Finished products . 22 A.4.1 Raw or incoming materials . 22 A.4.2 Alternative tests . 25 A.4.3 Equipment . 25 A.4.4 Provisions applicable to A.2, A.3 and A.4 (to be used where appropriate) . 26 Annex B (normative)
Durability of geosynthetic barriers . 27 B.1 Introduction . 27 B.1.1 Standards to which this annex is common . 27 B.1.2 Mechanisms of degradation . 27 SIST EN 13361:2013
EN 13361:2013 (E) 3 B.1.3 Service life . 28 B.1.4 Use of rework materials . 28 B.2 Test requirements . 28 B.2.1 General requirement . 28 B.2.2 Requirements for repeat testing . 28 B.2.3 Requirements for individual materials . 29 B.3 Durability tests . 30 B.3.1 Introduction . 30 B.3.2 Weathering . 30 B.3.3 Resistance to micro-organisms . 32 B.3.4 Resistance to environmental stress cracking . 32 B.3.5 Resistance to leaching. 32 B.3.6 Resistance to oxidation . 33 B.3.7 Chemical resistance . 33 B.4 Evaluation tests and acceptance criteria . 33 B.4.1 General . 33 B.4.2 Evaluation by comparison of tensile properties . 33 B.4.3 Evaluation by comparison of Oxidative Induction Time (OIT) values . 34 B.4.4 Evaluation by change in mass . 34 B.4.5 Evaluation by change in water permeability . 34 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Directive . 35 ZA.1 Scope and relevant characteristics . 35 ZA.2 Procedure for attestation of conformity of geosynthetic barriers . 36 ZA.3 CE marking and labelling . 38 Bibliography . 41
SIST EN 13361:2013
EN 13361:2013 (E) 4 Foreword This document (EN 13361:2013) has been prepared by Technical Committee CEN/TC 189 “Geosynthetics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2014, and conflicting national standards shall be withdrawn at the latest by January 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13361:2004. The following technical changes were introduced in comparison with the previous edition: The normative references were updated. Table 1 was revised. "Chemical resistance” was added to Clause 4. “Release of dangerous substances” was added to Clause 4. Annex A revised: “raw or incoming material” and Tables A.1 to A.3 were added. Annex B was revised. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 13361:2013
EN 13361:2013 (E) 5 Introduction This document allows manufacturers to describe geosynthetic barriers on the basis of declared values for characteristics relevant to the intended use and if tested to the specified method. It also includes procedures for evaluation of conformity and factory production control. This document can also be used by designers, end-users and other interested parties as a tool to define relevant and appropriate characteristics for specifications and on-site quality control. It should be emphasised that not all characteristics and test methods quoted in this document are suitable for the purpose of on-site quality control.
Tests for some non-mandated characteristics are still under study and will be included when the standard is revised. The term “product” used in this document refers to a geosynthetic barrier, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers. This document is part of a group of standards, addressing the requirements for geosynthetic barriers when used in a specific application.
Particular application cases can contain requirements about additional properties and – preferably standardised – test methods, if they are technically relevant and not conflicting with European Standards.
The design life of the product should be determined, since its function may be temporary, as construction expediency, or permanent, for the lifetime of the structure.
SIST EN 13361:2013
EN 13361:2013 (E) 6 1 Scope This European Standard specifies the relevant characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, to be used as fluid barriers for potable, fresh or saline water, in the construction of reservoirs and dams, and the appropriate test methods to determine these characteristics.
The intended use of these products is to control the leakage of water through the construction.
This European Standard is not applicable to geotextiles or geotextile-related products. This European Standard provides for the evaluation of conformity of the product to this document. This European Standard defines requirements to be met by manufacturers and their authorised representatives with regard to the presentation of product properties.
This European Standard does not cover applications where the geosynthetic barrier is to be in contact with water that has been treated for human consumption. Where potable water is or may be in direct contact with the product the designer should also refer to other relevant standards, requirements and/or regulations. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 495-5, Flexible sheets for waterproofing — Determination of foldability at low temperature — Part 5: Plastic and rubber sheets for roof waterproofing EN 1109, Flexible sheets for waterproofing — Bitumen sheets for roof waterproofing — Determination of flexibility at low temperature EN 1849-1, Flexible sheets for waterproofing — Determination of thickness and mass per unit area — Part 1: bitumen sheets for roof waterproofing EN 1849-2, Flexible sheets for waterproofing — Determination of thickness and mass per unit area — Part 2: Plastic and rubber sheets
EN 1844, Flexible sheets for waterproofing — Determination of resistance to ozone — Plastic and rubber sheets for roof waterproofing EN 12224, Geotextiles and geotextile-related products — Determination of the resistance to weathering EN 12225, Geotextiles and geotextile-related products — Method for determining the microbiological resistance by a soil burial test EN 12310-1, Flexible sheets for waterproofing — Part 1: Bitumen sheets for waterproofing — Determination of resistance to tearing (nail shank) EN 12311-1, Flexible sheets for waterproofing — Part 1: Bitumen sheets for roof waterproofing — Determination of tensile properties EN 12311-2, Flexible sheets for waterproofing — Determination of tensile properties — Part 2: Plastic and rubber sheets for roof waterproofing SIST EN 13361:2013
EN 13361:2013 (E) 7 EN 13362, Geosynthetic barriers — Characteristics required for use in the construction of canals EN 13491, Geosynthetic barriers — Characteristics required for use as a fluid barrier in the construction of tunnels and underground structures EN 13492, Geosynthetic barriers — Characteristics required for use in the construction of liquid waste disposal sites, transfer stations or secondary containment EN 13493, Geosynthetic barriers — Characteristics required for use in the construction of solid waste storage and disposal sites EN 14150, Geosynthetic barriers — Determination of permeability to liquids EN 14151, Geosynthetics — Determination of burst strength EN 14196, Geosynthetics — Test methods for measuring mass per unit area of clay geosynthetic barriers EN 14414, Geosynthetics — Screening test method for determining chemical resistance for landfill applications EN 14415, Geosynthetic barriers — Test method for determining the resistance to leaching CEN/TS 14416, Geosynthetic barriers — Test method for determining the resistance to roots CEN/TS 14417, Geosynthetic barriers — Test method for the determination of the influence of wetting-drying cycles on the permeability of clay geosynthetic barriers CEN/TS 14418, Geosynthetic barriers — Test method for the determination of the influence of freezing-thawing cycles on the permeability of clay geosynthetic barriers EN 14575, Geosynthetic barriers — Screening test method for determining the resistance to oxidation EN 14576, Geosynthetics — Test method for determining the resistance of polymeric geosynthetic barriers to environmental stress cracking EN 15382, Geosynthetic barriers — Characteristics required for use in transportation infrastructure EN 16416, Geosynthetic clay barriers — Determination of water flux index — Flexible wall permeameter method at constant head EN ISO 527-1:2012, Plastics — Determination of tensile properties — Part 1: General principles (ISO 527-1:2012) EN ISO 527-3:1995, Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets (ISO 527-3:1995) EN ISO 527-4:1997, Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:1997) EN ISO 9862, Geosynthetics — Sampling and preparation of test specimens (ISO 9862) EN ISO 9863-1, Geosynthetics — Determination of thickness at specified pressures — Part 1: Single layers (ISO 9863-1) EN ISO 9864, Geosynthetics — Test method for the determination of mass per unit area of geotextiles and geotextile-related products (ISO 9864) EN ISO 10318:2005, Geosynthetics —Terms and definitions (IS0 10318:2005) SIST EN 13361:2013
EN 13361:2013 (E) 8 EN ISO 10319, Geotextiles — Wide-width tensile test (ISO 10319) EN ISO 10320, Geotextiles and geotextile-related products — Identification on site (ISO 10320) EN ISO 11358, Plastics — Thermogravimetry (TG) of polymers — General principles (ISO 11358) EN ISO 12236, Geosynthetics — Static puncture test (CBR test) (ISO 12236) EN ISO 12957-1, Geosynthetics — Determination of friction characteristics — Part 1: Direct shear test (ISO 12957-1) EN ISO 12957-2, Geosynthetics — Determination of friction characteristics — Part 2: Inclined plane test (ISO 12957-2) EN ISO 13438, Geotextiles and geotextile-related products — Screening test method for determining the resistance to oxidation (ISO 13438) ISO 34-1, Rubber, vulcanized or thermoplastic — Determination of tear strength — Part 1: Trouser, angle and crescent test pieces ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) ASTM D696, Standard test method for coefficient of linear thermal expansion of plastics between -30 °C and 30 °C ASTM D5890, Standard test method for swell index of clay mineral component of geosynthetic clay liners ASTM D6141, Standard guide for screening clay portion of geosynthetic clay liner (GCL) for chemical compatibility to liquids
3 Terms, definitions and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 10318:2005 and the following apply.
3.1.1 product geosynthetic barrier, including polymeric, bituminous and clay barriers 3.1.2 specification any document in which the works, functions, specific conditions and required material property values of the geosynthetic barrier of use are described 3.1.3 reservoir naturally occurring space or construction for storage, regulation and control of water 3.1.4 dam barrier constructed to hold back water to raise its level, form a reservoir or reduce or prevent flooding 3.1.5 upstream face face of a dam that is normally in contact with the enclosed water SIST EN 13361:2013
EN 13361:2013 (E) 9 3.1.6 downstream face face of a dam that is normally not in contact with the enclosed water 3.1.7 revetment construction that comprises one or more layers of material to provide protection against erosion 3.1.8 top water level maximum operating water level in any structure 3.2 Abbreviations For the purposes of this document, the abbreviations given in EN ISO 10318:2005 and the following apply. GBR-P: polymeric geosynthetic barrier GBR-B: bituminous geosynthetic barrier GBR-C: clay geosynthetic barrier 4 Required characteristics and corresponding methods of test 4.1 General The main function of geosynthetic barriers when used in the construction of reservoirs and dams for potable, fresh or saline water is to prevent or reduce the flow of fluid through the structure. Damage during installation has not been addressed in this European Standard. 4.2 Types of application
4.2.1 General It is not normally advisable to install a geosynthetic barrier on the downstream face of a dam. Special consideration should be given to any geosynthetic barrier installed on the downstream face of a dam. The applications described in this European Standard do not include such situations. 4.2.2 Application 1: "covered in service" In these applications, the product is laid on the upstream face of a dam or in a reservoir and is covered in service with a revetment or other protective layers. Figure 1 and Figure 2 show typical installations.
SIST EN 13361:2013
EN 13361:2013 (E) 10
Key 1 top water level 2 upstream face 3 revetment 4 geosynthetic barrier 5 dam body Figure 1 — A geosynthetic barrier on a reservoir or dam slope (shallow), covered in service SIST EN 13361:2013
EN 13361:2013 (E) 11
Key 1 top water level face of dam 2 geosynthetic protection layer 3 geosynthetic barrier
4 facing
5 body of dam
Figure 2 — A geosynthetic barrier on a reservoir or dam slope (steep), covered in service SIST EN 13361:2013
EN 13361:2013 (E) 12 4.2.3 Application 2: "not covered in service" As in application 1, but with the product not covered in service with a revetment or other protective layers. Figure 3 and Figure 4 show typical installations.
Key 1 top water level
2 upstream face 3 geosynthetic barrier 4 dam body Figure 3 — A geosynthetic barrier on a reservoir or dam slope (shallow), exposed in service SIST EN 13361:2013
EN 13361:2013 (E) 13
Key 1 top water level
2 geosynthetic barrier
3 body of dam Figure 4 — A geosynthetic barrier on a reservoir or dam slope (steep), exposed in service 4.3 Relevant characteristics The characteristics and the test methods to be used are given in Table 1. The list of characteristics in Table 1 includes those relevant to all conditions of use and subject to harmonisation (H) (see Annex ZA), those relevant to all conditions of use and not subject to harmonisation (A), and those relevant to specific conditions of use and not subject to harmonisation (S).
The functions and conditions of use, corresponding with the characteristics, marked with “S” in Table 1, are specified in 4.4.
The manufacturer shall provide the data based on the results of tests specified in this document and, where relevant, in accordance with 5.1. The manufacturer shall provide information on how functioning joints can be made. Where products are jointed in the factory the water permeability and if relevant the strength of the joints shall be tested and data presented. SIST EN 13361:2013
EN 13361:2013 (E) 14 Table 1 — Geosynthetic barriers used in the construction of reservoirs and dams - Functions, function-related characteristics and test methods to be used.
Covered in service Not covered in service Test methods Remarks Nr Property to be tested GBR-P GBR-B GBR-C GBR-P GBR-B GBR-P GBR-B GBR-C
Physical properties
1 Thickness A A A A A EN 1849-2 EN 1849-1 EN 9863-1
2 Mass per unit area A A A A A EN 1849-2 EN 1849-1 EN 14196
Hydraulic properties
3 Water permeability (liquid tightness)
H H H H H EN 14150 EN 14150 EN 16416 Report index flux for GBR-C.
4 Swell index - - A - - - - ASTM D5890
Mechanical properties
5 Tensile strength
H H H H H EN ISO 527-1 EN ISO 527-3 EN ISO 527-4 or EN 12311-2 EN 12311-1 EN ISO 10319 For non-reinforced GBR-P use EN ISO 527-1 and EN ISO 527-3:1995, test specimen type 5 at a speed of 100 mm/min.
For reinforced GBR-P use EN ISO 527-1 and EN ISO 527-4:1997, specimen type 2 with width 50 mm, at a speed of 5 mm/min. EN 12311-2 should only be used for non-polyolefinic GBR-P. Report in all cases the maximum strength measured according to the test method.
SIST EN 13361:2013
EN 13361:2013 (E) 15 Table 1 (continued)
Covered in service Not covered in service Test methods Remarks Nr Property to be tested GBR-P GBR-B GBR-C GBR-P GBR-B GBR-P GBR-B GBR-C
6 Elongation A A A A A EN ISO 527-1 EN ISO 527-3 EN ISO 527-4 or EN 12311-2 EN 12311-1 EN ISO 10319 For non-reinforced GBR-P use EN ISO 527-1 and EN ISO 527-3:1995, test specimen type 5 at a speed of 100 mm/min.
For reinforced GBR-P use EN ISO 527-1 and EN ISO 527-4:1997, specimen type 2, width 50 mm, at a speed of 5 mm/min. Calculation of elongation as defined in EN ISO 527-1:2012, 10.2, using grip sep
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.