Safety requirements for lifting tables - Part 2: Lifting tables serving more than 2 fixed landings of a building, for lifting goods with a vertical travel speed not exceeding 0,15 m/s

1.1   This European Standard specifies the safety requirements applicable to slow-speed platform lifts presenting the following characteristics:
   serving 2 or more set levels of a building or construction structure;
   able to cross landings;
   designed exclusively for lifting or lowering loads;
   only accessible to operators during the loading/unloading phases;
   with a travel speed of no more than 0.15 m/s;
   useable solely by people who have been authorized and briefed;
   permanently installed.
1.2   This European Standard deals with all significant hazards pertinent to slow-speed platform lifts when used as intended and under the conditions foreseen by the manufacturer (see Article 4). This European Standard specifies the appropriate technical measures for eliminating and reducing the risks arising from the significant hazards.
1.3   This European Standard does not apply to the following equipment:
   permanently and/or temporarily installed platform lifts, serving specific levels of a building, with a vertical travel speed exceeding 0.15 m/s (EN 81-31);
   lifting tables serving no more than two set levels of a building and not crossing a landing (EN 1570-1);
   lift platforms designed for mobility-impaired persons (EN 81-40 and prEN 81 41);
   platform lifts used on ships;
   lifts designed for lifting artists and stage set features during artistic performances;
   lifts driven by pusher chains.

Sicherheitsanforderungen an Hubtische - Teil 2: Hubtische zum Heben von Gütern, die mehr als 2 Haltestellen eines Gebäudes anfahren und deren Hubgeschwindigkeit 0,15 m/s nicht überschreitet

1.1   Diese Europäische Norm legt die geltenden Sicherheitsanforderungen für Hubtische fest, die folgende Eigenschaften aufweisen:
   Bedienen von 2 oder mehr Haltestellen eines Gebäudes oder Bauwerks;
   Durchfahren von festen Haltestellen;
   ausschließlich zum Heben und Senken von Gütern, aber nicht für Personen, gestaltet;
   nur während des Be-/Entladens für Personen zugänglich;
   Hubgeschwindigkeit von nicht mehr als 0,15 m/s;
   fest eingebaut.
1.2   Diese Europäische Norm behandelt alle von Hubtischen ausgehenden signifikanten Gefährdungen, wenn diese bestimmungsgemäß nach der Bedienungsanleitung und unter den darin vorgesehenen Bedin-gungen benutzt werden (siehe Abschnitt 4). Diese Europäische Norm legt die geeigneten technischen Maß-nahmen zur Vermeidung oder Verminderung der Risiken fest, die sich aus den zutreffenden Gefährdungen ergeben.
1.3   Diese Europäische Norm gilt nicht für die folgenden Geräte:
   dauerhaft eingebaute Hubtische, die festgelegte Ebenen eines Gebäudes mit einer vertikalen Hubge-schwindigkeit anfahren, die 0,15 m/s (EN 81-31) überschreitet;
   Hubtische, die nicht mehr als 2 ortsfeste Haltestellen eines Gebäudes anfahren und die keine Haltestelle durchfahren (EN 1570-1);
   Hubtische zum Heben von Bedienpersonen, die mehr als 2 ortsfeste Haltestellen eines Gebäudes anfahren und deren Hubgeschwindigkeit 0,15 m/s (prEN 1570-3) nicht überschreitet;
   Hubtische zum Befördern von Bedienpersonen, eingebaut mit einer vollständigen Einhausung (prEN 1570 3);
   Hubtische für die Verwendung auf Schiffen;
   Hebevorrichtungen zum Bewegen von Künstlern und Versenk- und Hebevorrichtungen von Theaterbühnen während künstlerischer Darbietungen;
   Hebevorrichtungen, die durch Schubketten angetrieben werden.
1.4   Diese Europäische Norm legt keine zusätzlichen Anforderungen fest für:
   elektromagnetische Verträglichkeit;
   Betrieb unter erschwerten Bedingungen (z. B. extremes Klima, Anwendungen im Gefrierbereich, starke Magnetfelder);
   Betrieb, der besonderen Regelungen unterliegt (z. B. potentiell explosive Atmosphäre, Bergwerk);
   die Handhabung von Lasten, die von ihrer Natur her zu gefährlichen Situationen führen könnten (z. B. geschmolzene Metalle, Säuren, strahlende Materialien, besonders spröde Lasten, lose Lasten (Kies, Rohre));
   Gefährdungen, die während Herstellung, Transport und Entsorgung auftreten;
   Ausrüstungsteile, die auf der Lastplattform angebracht werden oder diese ersetzen;
   den Einbau in umfassende Systeme oder in andere Maschinen usw.;
   drahtlose Steuerungen;
   Hubtische, bei denen der Hydraulikdruck direkt durch Gasdruck erzeugt wird;
   den Antrieb des Hubtisches durch Verbrennungsmotoren.

Prescriptions des tables élévatrices - Partie 2: Tables élévatrices desservant plus de deux paliers fixes d'un bâtiment utilisées pour transporter des marchandises et dont la vitesse ne dépasse pas 0,15 m/s

1.1   La présente Norme européenne spécifie les prescriptions de sécurité applicables aux tables élévatrices présentant les caractéristiques suivantes :
-   desservant 2 paliers fixes ou plus d'un bâtiment ou d'un ouvrage ;
-   pouvant traverser des planchers ;
-   exclusivement conçues pour lever ou descendre des charges et non des personnes ;
-   accessibles aux opérateurs uniquement pendant les phases de chargement /déchargement ;
-   avec une vitesse de déplacement ne dépassant pas 0,15 m/s ;
-   installées à demeure.
1.2   La présente Norme européenne traite de tous les phénomènes dangereux significatifs relatifs aux tables élévatrices utilisées selon les conditions prévues par le fabricant (voir Article 4). La présente Norme européenne spécifie les mesures techniques appropriées pour réduire et éliminer les risques émanant des phénomènes dangereux significatifs.
1.3   La présente Norme européenne ne s'applique pas aux équipements suivants :
-   les tables élévatrices installées de manière permanente, desservant des niveaux spécifiques d'un bâtiment et dont la vitesse de translation verticale est supérieure à 0,15 m/s (EN 81-31) ;
-   les tables élévatrices ne desservant pas plus de 2 paliers fixes d’un bâtiment et ne traversant pas de plancher (EN 1570-1) ;
-   les tables élévatrices desservant plus de 2 paliers fixes d'un bâtiment pour élever des opérateurs, avec une vitesse de translation verticale ne dépassant pas 0,15 m/s (prEN 1570-3) ;
-   les tables élévatrices transportant des opérateurs et installées dans des enceintes entièrement fermées (prEN 1570-3) ;
-   les tables élévatrices utilisées à bord de navires ;
-   les élévateurs prévus pour élever des artistes et des décors pendant les représentations artistiques ;
-   les élévateurs actionnés par des chaînes de poussée.
1.4   La présente Norme européenne ne fixe pas de prescriptions supplémentaires concernant :
-   la compatibilité électromagnétique ;
-   une utilisation dans les conditions sévères (par exemple, climats extrêmes, application dans les chambres froides, champ magnétique élevé) ;
-   une utilisation soumise à des règles spéciales (par exemple, atmosphère potentiellement explosible, mines) ;
-   la manutention de charges dont la nature pourrait engendrer des situations dangereuses (par exemple, métal fondu, acides, matériaux rayonnants, charges particulièrement fragiles, charges en vrac (gravier, tubes…)) ;
-   les phénomènes dangereux engendrés lors d'opérations de construction, de transport, ou de mise au rebut ;
-   les équipements montés sur la plate-forme de chargement ou remplaçant celle-ci ;
-   l'intégration dans des systèmes ou d'autres machines, etc. ;
-   les radiocommandes ;
-   les tables élévatrices dont la pression hydraulique est directement dérivée de la pression d'un gaz ;
-   les tables élévatrices alimentées par des moteurs à combustion interne.

Varnostne zahteve za dvižne mize - 2. del: Dvižne mize za dvigovanje do več kot dveh stalnih nivojev v stavbi, katerih hitrost navpičnega dvigovanja ne presega 0,15 m/s

1.1   Ta evropski standard določa varnostne zahteve za dvižne ploščadi z nizko hitrostjo, ki imajo naslednje lastnosti:    uporabljajo se za dvigovanje dveh ali več stalnih nivojev v stavbi ali gradbeni konstrukciji;    lahko prečkajo nivoje;    zasnovana so izključno za dvigovanje ali spuščanje bremen;    dostopna so samo upravljavcem med postopkom natovarjanja/raztovarjanja;    imajo hitrost dvigovanja, ki ne presega 0,15 m/s;    uporabljajo jih lahko izključno pooblaščene osebe, ki so poučene o njihovi uporabi;    so trajno nameščena. 1.2   Ta evropski standard obravnava vse pomembne nevarnosti, povezane z dvižnimi ploščadmi z nizko hitrostjo, kadar se uporabljajo v skladu z namembnostjo in pod pogoji, ki jih je predvidel proizvajalec (glej člen 4). Ta evropski standard določa ustrezne tehnične ukrepe za odpravljanje in zmanjševanje tveganj, ki izhajajo iz večjih nevarnosti. 1.3   Ta evropski standard se ne uporablja za naslednjo opremo:    stalno in/ali začasno nameščene dvižne ploščadi za dvigovanje do določenih nivojev stavbe s hitrostjo navpičnega dvigovanja, ki presega 0,15 m/s (EN 81-31);    dvižne mize za dvigovanje do največ dveh nivojev stavbe, ki ne prečkajo nivojev (EN 1570-1);    dvižne ploščadi, zasnovane za osebe z omejenimi gibalnimi sposobnostmi (EN 81-40 in prEN 81 41);    dvižne ploščadi, ki se uporabljajo na ladjah;    dvigala, zasnovana za dvigovanje izvajalcev in scenskih rekvizitov med umetniškimi predstavami;    dvigala, ki jih poganjajo potisne verige.

General Information

Status
Published
Public Enquiry End Date
24-Jul-2016
Publication Date
19-Feb-2017
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
02-Feb-2017
Due Date
09-Apr-2017
Completion Date
20-Feb-2017

Buy Standard

Standard
EN 1570-2:2017 - BARVE
English language
42 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheitsanforderungen an Hubtische - Teil 2: Hubtische zum Heben von Gütern, die mehr als 2 Haltestellen eines Gebäudes anfahren und deren Hubgeschwindigkeit 0,15 m/s nicht überschreitetPrescriptions des tables élévatrices - Partie 2: Tables élévatrices desservant plus de deux paliers fixes d'un bâtiment utilisées pour transporter des marchandises et dont la vitesse ne dépasse pas 0,15 m/sSafety requirements for lifting tables - Part 2: Lifting tables serving more than 2 fixed landings of a building, for lifting goods with a vertical travel speed not exceeding 0,15 m/s53.020.99Druga dvigalna opremaOther lifting equipmentICS:Ta slovenski standard je istoveten z:EN 1570-2:2016SIST EN 1570-2:2017en,fr,de01-marec-2017SIST EN 1570-2:2017SLOVENSKI
STANDARD



SIST EN 1570-2:2017



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1570-2
November
t r s x ICS
w uä r t rä { { English Version
Safety requirements for lifting tables æ Part
tã Lifting tables serving more than
t fixed landings of a buildingá for lifting Prescriptions de sécurité des tables élévatrices æ Partie
t ã Tables élévatrices desservant plus de deux paliers fixes d 5un bâtiment utilisées pour transporter des marchandises et dont la vitesse ne dépasse pas
rá s w
Sicherheitsanforderungen an Hubtische æ Teil
tã Hubtische zum Heben von Güterná die mehr als
t Haltestellen eines Gebäudes anfahren und deren This European Standard was approved by CEN on
t y August
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s w y ræ tã t r s x ESIST EN 1570-2:2017



EN 1570-2:2016 (E) 2 Contents Page European foreword . 4 Introduction . 5 1 Scope . 6 2 Normative references . 7 3 Terms and definitions . 8 4 List of hazards . 10 5 Safety requirements and/or protective measures . 10 5.1 General . 10 5.2 Calculations . 10 5.2.1 Stresses . 10 Table 1 — Load factors for lifting tables . 11 5.2.2 Platform deflection . 11 Figure 1 — Deflection of platform . 12 5.2.3 Strength of the load-bearing structure. 12 5.2.4 Stability . 12 5.3 General requirements . 13 5.3.1 Safety distances. 13 5.3.2 High temperatures . 13 5.3.3 Speed. 13 5.4 Protection for the travel zone and for the platform . 14 5.4.1 General requirements . 14 5.4.2 Protection of the travel zone . 14 5.4.3 Protection for the area underneath the platform . 14 5.4.4 Protection for the platform . 15 5.4.5 Guard-rails . 15 Figure 2a — Horizontal guard-rail . 16 Figure 2b — Clear space between two guard-rail segments . 16 5.4.6 Gates. 17 Figure 3 — Performance level depending on the fall risk . 18 5.4.7 Flexible guards . 20 5.4.8 Screens . 20 5.5 Design of the platform . 20 5.6 Levels and clearances of fixed landings . 20 5.7 Driving system . 21 5.7.1 Mechanical chains driving system . 21 5.7.2 Hydraulic system . 21 Table 2 — Hydraulic pipe rupture protection device . 22 5.8 Controls . 25 5.9 Electrical system . 26 5.9.1 General requirements . 26 5.9.2 Protection rating . 26 5.10 Safety devices . 26 SIST EN 1570-2:2017



EN 1570-2:2016 (E) 3 5.10.1 General requirements . 26 5.10.2 Trip devices . 26 Figure 5 — Configuration of a trip device . 27 5.10.3 Safety devices for maintenance . 27 6 Verification of the safety requirements and/or measures . 27 6.1 General requirements . 27 Table 3 — Means of verification of the safety requirements and measures . 28 6.2 Design check . 29 6.3 Manufacturing check . 29 6.4 Visual inspection . 29 6.5 Electrical tests . 29 6.6 Individual final verification before putting into service (fitness for purpose) . 29 7 Marking . 29 8 Instructions for the user . 30 8.1 General requirements . 30 8.2 Instructions for use . 31 8.3 Instructions for installation . 32 8.4 Instructions for maintenance and inspection . 32 Annex A (normative)
Test procedures . 34 Annex B (informative)
Safety signs . 36 Annex C (informative)
Table with the list of hazards . 38 Table C.1 — List of hazards. 38 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC . 41 Bibliography . 42
SIST EN 1570-2:2017



EN 1570-2:2016 (E) 4 European foreword This document (EN 1570-2:2016) has been prepared by Technical Committee CEN/TC 10 “Lilts, escalators and moving walks”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be withdrawn at the latest by May 2017. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports the essential requirements of 2006/42/EU. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN
shall not be held responsible for identifying any or all such patent rights. For the relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 1570-2:2017



EN 1570-2:2016 (E) 5 Introduction This European Standard document was drafted as a design guidance manual to provide a means of achieving conformance to the essential safety requirements stipulated under Machinery Directive 2006/42/EC. The machines concerned and the extent to which hazards, hazardous situations and hazardous incidents are covered are indicated in the scope of this European Standard. In addition, the machines should be designed according to the principles of EN ISO 12100 for relevant but non significant hazards, which are not dealt with in this standard. As lifting tables are used in a wide range of applications, it is equally necessary to perform individual risk assessments in accordance with EN ISO 12100 for the actual operating conditions. Products sold indirectly to end-users should be built to cover all the risks related to the use and all conditions foreseeable by the manufacturer, as described in the instruction manual. Where the text gives an example of a safety measure for the purposes of greater clarity, this should not be considered as the only possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent or increased level of safety is achieved. While drafting this European Standard document, it was assumed that:
the lifting tables are only operated by persons trained in using the equipment in accordance with the manufacturer's instructions, and that the working area is adequately lit;
the lifting tables are installed on hard-standing, even, appropriately prepared surfaces.
where there are special requirements on low noise levels, such as for hospital applications and theatres etc., the customer should specify these requirements and the manufacturer should then take all appropriate measures. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. SIST EN 1570-2:2017



EN 1570-2:2016 (E) 6 1 Scope 1.1 This European Standard specifies the safety requirements applicable to lifting tables presenting the following characteristics: — serving more than two fixed landings of a construction; — able to pass landings; — designed exclusively for lifting or lowering goods and not persons; — only accessible to persons during the loading/unloading phases; — with a travel speed of no more than 0,15 m/s; — permanently installed. 1.2 This European Standard deals with all significant hazards pertinent, with the exception of noise, to lifting tables when used as intended and under the conditions foreseen by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures for eliminating and reducing the risks arising from the significant hazards. 1.3 This European Standard does not apply to the following equipment: — permanently installed lifting tables, serving specific levels of a construction, with a vertical travel speed exceeding 0,15 m/s (EN 81-31); — lifting tables serving not more than two fixed landings of a construction (EN 1570-1); — lifting tables, serving more than 2 fixed landings of a construction for lifting operators, with a vertical travel speed not exceeding 0,15 m/s; — lifting tables carrying operators and installed in enclosures with a vertical travel speed not exceeding 0,15 m/s; — lifting tables used on ships; — lifting tables designed for artists and stage set features during artistic performances; — lifting tables driven by pusher chains. 1.4 This European Standard does not establish the additional requirements for: — electromagnetic compatibility; — operation in severe conditions (e.g. extreme climates, freezer applications, strong magnetic fields); — operation subject to special rules (e.g. potentially explosive atmospheres, mines); — handling of loads, the nature of which could lead to dangerous situations (e.g. molten metal, acids, radiating materials, particularly brittle loads, loose loads (gravel, tubes)); — hazards occurring during construction, transportation and disposal; SIST EN 1570-2:2017



EN 1570-2:2016 (E) 7 — equipment installed on the load platform or the replacing or maintaining of it; — integration into broader systems or other machines, etc.; — cable-less controls; — lifting tables where the hydraulic pressure is derived directly from gas pressure; — lifting tables powered by internal combustion engines. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 349:1993+A1:2008, Safety of machinery - Minimum gaps to avoid crushing of parts of the human body EN 13001 (all parts), Cranes - General design EN 60204-1:20061, Safety of machinery - Electrical equipment of machines - Part 1: General requirements (IEC 60224-1:2005, modified) EN 60204-32:2008, Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines (IEC 60204-32:2008) EN 60529:19912, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989) EN 60947-5-1:2004,3 Low-voltage switchgear and controlgear - Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices (IEC 60947-5-1:2003) EN 60947-5-3:2013, Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB) (IEC 60947-5-3:2013) EN 61310-2:2008, Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking (IEC 61310:2007) EN 61496-1:2013, Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests (IEC 61496-1:2012) EN 61496-2:2013, Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2013) EN ISO 4413:2010, Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) EN ISO 12100:2010, Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
1 As impacted by EN 60204-1:2006/A1:2009. 2 As impacted by EN 60529:1991/A1:2000 and EN 60529:1991/A2:2013 3 As impacted by EN 60947-5-1:2004/A1:2009 SIST EN 1570-2:2017



EN 1570-2:2016 (E) 8 EN ISO 13849-1:2015, Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) EN ISO 13850:2015, Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) EN ISO 13857:2008, Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) EN ISO 14119:2013, Safety of machinery - Interlocking devices associated with guards - Principles for design and selection (ISO 14119:2013) EN ISO 14122-3:2001, Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2001) ISO 606:2015, Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets ISO 4347:2015, Leaf chains, clevises and sheaves — Dimensions, measuring forces, tensile strengths and dynamic strengths 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 12100 and the following apply. 3.1 lifting table load-lifting device with a load-supporting platform rigidly guided throughout its travel (e.g. a scissor lift) 3.2 fixed landing permanent level of the construction for loading and unloading the lifting table 3.3 platform part of the lifting table designed to accommodate the working load; fork arms are considered as a load platform for goods only 3.4 vertical travel vertical distance between the lowest and highest fixed landing for which the lifting table is designed 3.5 rated load load that the manufacturer has stated that the machine is capable of lifting/lowering when used in accordance with the instruction handbook 3.6 guard part of the machine specifically used to provide protection by means of a physical barrier SIST EN 1570-2:2017



EN 1570-2:2016 (E) 9 3.7 emergency stop control component of emergency stop equipment which generates the emergency stop signal when the associated manual control (actuator) is operated 3.8 operator person who is trained to operate the lifting table, according to the manufacturer's instructions 3.9 maximum working pressure highest pressure in the hydraulic system at which it is intended to operate under normal working conditions with rated load 3.10 travel zone space through which the lifting mechanism, platform and any attachment to it, moves 3.11 restricted area area to which access is restricted only to persons who are authorized to be in that area, and not accessible to the public 3.12 public area areas to which the public have access 3.13 travel speed average lifting and lowering speed of the platform when measured throughout its normal travel range 3.14 screen permanent protection from access to the hazard for the whole body, also called distance guards in EN ISO 14120:2015 3.15 guard-rail device for protection against accidental fall or accidental access to a hazardous area, with which stairs, step ladders, landing or platforms and walkways (level surface used for moving from one point to another) may be equipped 3.16 enclosure permanent protection where the whole of the travel zone is protected with rigid panels to make the lifting table inaccessible whilst in operation 3.17 automatic programmable controlled lifting table lifting table designed for the lifting of goods only, where movement that takes place is not initiated by hold-to run manual controls SIST EN 1570-2:2017



EN 1570-2:2016 (E) 10 3.18 toe guard vertical component extending downwards from the platform entrance 3.19 gate opening part of the protection means, to give access from a fixed landing to the platform (e.g. barrier, door, vertical hinged, sliding…) 4 List of hazards The table that contains all the significant hazards, hazardous situations and events, identified by risk assessment significant for lifting tables and for which require action to eliminate or reduce the risk is in Annex C. 5 Safety requirements and/or protective measures 5.1 General Lifting tables shall comply with the safety requirements and/or protective measures within this clause. In addition, the lifting table shall be designed according to the principles of EN ISO 12100 for relevant but insignificant hazards, which are not dealt with by this standard. 5.2 Calculations 5.2.1 Stresses 5.2.1.1 The lifting table shall be designed in accordance with known standard calculation rules (e.g. EN 13001, all parts) and good engineering practices, and all equipment failure modes shall be taken into account, including fatigue failure. 5.2.1.2 The stresses in any part of the lifting table assessed using the permissible stress method shall not, under normal working conditions, exceed the lowest of the following values: a) 0,66 times the yield stress of the material used; or b) 0,50 times the ultimate tensile stress of the material used. 5.2.1.3 The stresses shall be calculated for a lifting table carrying its rated load and being used in compliance with the manufacturer's instructions. The loads shall include all real static and dynamic forces, both vertical and horizontal, all wind forces, and all forces applied to the platform during loading and unloading. 5.2.1.4 The minimum dynamic forces to be used for the calculations set out under 5.2.1.3 shall result from: a) the total vertical load (this includes the rated load and the self-weight of the moving parts of the structure) increased by the dynamic factor for the category of lift shown in Table 1; and b) the horizontal load coefficient for the category of lift shown in Table 1, taken as acting horizontally at the platform level in the direction causing the maximum stress in the part being considered. SIST EN 1570-2:2017



EN 1570-2:2016 (E) 11 Table 1 — Load factors for lifting tables Lift category Dynamic factor Horizontal load coefficient [in % of the rated load] Lifetime b minimum load cycles under full load [x103] Examples of use (informative) 1 1,4 10 % 128a Lifting tables for general purpose. 2 1,1 2,5 % 8 Lifting tables with a clearly defined lifting load and where other forces can be excluded; height adjustment without systematic lateral forces. 3 1,2 5,0 % 32 Not applicable 4 1,3 10 % 128 Lifting tables suited for crossing with, e.g. manually operated industrial trucks, electric pallet-stacking trucks with a maximum braking of 10 %.
Lifting tables with mounted gravity conveyors. 5 1,4 10 % 512 Lifting tables suited for a high number of cycles When a lifting table is crossed by vehicles, or is integrated in a handling device, the lateral forces have to be verified in individual cases. Higher horizontal load coefficients have to be established if required. a This minimum number of cycles shall be increased by the manufacturer according to the use of the lifting table. b When used (load cycle) according to lifting categories, the lifetime of lifting tables is generally 10 years when maintained in accordance with the manufacturer's instructions. NOTE 1 If permanent protection prevents loading or unloading across a side, or other means prevent movement of the platform in a particular direction, the horizontal load coefficient in this direction need not be considered. NOTE 2 Lifting tables are classified in 5 categories (called lift category) depending on the use for which it is designed. The dynamic factor, horizontal load coefficient and number of cycles used in the design calculations are defined in Table 1. 5.2.1.5 It shall be possible for the forces produced when the mechanical safety device is operated, to be accepted without permanent deformation of the normal load bearing parts, when used in accordance with the manufacturer’s instructions. 5.2.2 Platform deflection All lifting tables shall be designed to meet the following minimum requirements: a) in one case, lift half the rated load distributed over half the length or longest side of the platform; b) and in another case, lift one third of the rated load distributed over half the width or shortest side of the platform. SIST EN 1570-2:2017



EN 1570-2:2016 (E) 12 NOTE In cases involving upright-framed lifts, the length is considered as the edge running alongside the column. In neither case shall hazardous tilting or deflection take place when used as intended by the manufacturer. The maximum tilting or deflection shall not exceed that shown in Figure 1 where; a) is the maximum tilting or deflection (y) of any side up to 2,0 m (l) long and is (1(2/))%y=+− b) is the maximum tilting
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.