SIST EN ISO 16120-1:2011
(Main)Non-alloy steel wire rod for conversion to wire - Part 1: General requirements (ISO 16120-1:2011)
Non-alloy steel wire rod for conversion to wire - Part 1: General requirements (ISO 16120-1:2011)
This European Standard is applicable to rod of non-alloy steel intendedfor wire drawing and/or cold rolling. The cross-section of the rod may beround, square, rectangular, hexagonal, half-round or another shape and as ageneral rule of nominal size 5 mm or above the surface is smooth.It is not applicable to following products for which standards exist orare under study such as:
- steel rod intended for heat treatment
- rod of free-cutting steels
- steel rod for cold heading and cold extrusion
- steel rod intended for the production of electrodes and products forwelding
- steel rod for welded fabric for reinforcement for concrete
- steel rod for wire for high fatigue strength mechanical springs, suchas valve springs.
In addition to the requirements of this standards the general technicaldelivery requirements specified in EN 10021 apply.
Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 1: Allgemeine Anforderungen (ISO 16120-1:2011)
Die ISO 16120 gilt für Walzdraht aus unlegiertem Stahl zum Ziehen und/oder Kaltwalzen. Der
Querschnitt des Walzdrahtes ist rund, oval, vierkant, rechteckig, sechseckig, achteckig, halbrund oder von
anderer Form, und sein Nennmaß beträgt im allgemeinen mindestens 5 mm; seine Oberfläche ist glatt.
1.2 Dieser Teil der ISO 16120 stellt allgemeine Anforderungen dar und gilt nicht für die folgenden
Erzeugnisse, für die spezielle Normen bestehen oder in Vorbereitung sind:
Für eine Wärmebehandlung bestimmter Walzdraht aus Stahl;
⎯ Walzdraht aus Automatenstählen;
⎯ Walzdraht zum Kaltstauch- und Kaltfließpressen;
⎯ Walzdraht zur Herstellung von Elektroden und Schweißzusätzen;
⎯ Walzdraht für geschweißte Matten und zur Betonbewehrung;
⎯ Walzdraht für Wälzlager (siehe ISO 683-17);
⎯ Walzdraht für die Herstellung von Draht für Federn mit hoher Dauerschwingfestigkeit, wie Ventilfedern.
1.3 Zusätzlich zu den Anforderungen nach diesem Teil der ISO 16120 gelten die in ISO 404 festgelegten
allgemeinen technischen Lieferbedingungen.
Fil-machine en acier non allié destiné à la fabrication de fils - Partie 1: Exigences générales (ISO 16120-1:2011)
L'ISO 16120:2011 est applicable au fil-machine en acier non allié destiné au tréfilage et/ou au laminage à froid. La section droite du fil-machine peut être circulaire, ovale, carrée, rectangulaire, hexagonale, octogonale, demi-ronde ou autre, et en règle générale, de dimension nominale supérieure ou égale à 5 mm, et avec une surface lisse.
L'ISO 16120-1:2011 couvre les exigences générales et n'est pas applicable aux produits suivants, pour lesquels il existe des normes spécifiques ou des études en cours:
le fil-machine en acier destiné aux traitements thermiques;
le fil-machine en acier pour décolletage;
le fil-machine en acier pour frappe et extrusion à froid;
le fil-machine en acier destiné à la fabrication d'électrodes et de produits pour soudage;
le fil-machine en acier pour treillis soudés pour béton armé;
le fil-machine en acier pour les roulements à billes et à rouleaux (voir l'ISO 683‑17);
le fil-machine en acier pour fil à ressort à résistance élevée à la fatigue tels que les ressorts de soupapes.
En plus des exigences de l'ISO 16120-1:2011, les exigences techniques générales de livraison de l'ISO 404 s'appliquent.
Vroče valjana žica iz nelegiranega jekla za vlečenje in/ali hladno valjanje - 1. del: Splošne zahteve (ISO 16120-1:2011)
ISO 16120 velja za valjano žico iz nelegiranega jekla, ki se uporablja za vlečenje in/ali hladno valjanje žic. Prečni prerez je lahko krožen, ovalen, kvadraten, pravokoten, šestkoten, osmerokoten, polkrožen ali druge oblike, v splošnem z nazivno dimenzijo vsaj 5 mm in z gladko površino. Ta del ISO 16120 zajema splošne zahteve in ne velja za izdelke, za katere standardi obstajajo ali se pripravljajo, na primer za: - jekleno valjano žico za toplotno obdelavo; - jekleno valjano žico za prosto rezanje; - jekleno valjano žico za hladno preoblikovanje in hladno ekstruzijo; - jekleno valjano žico za proizvodnjo elektrod in izdelkov za varjenje; - jekleno valjano žico za varjeno blago za ojačitev betona; - jekleno valjano žico za kroglične in kotalne ležaje (glej ISO 683-17); - jekleno valjano žico za žice za mehanske vzmeti z visoko dinamično trdnostjo, kot so ventilske vzmeti. Poleg zahtev v tem delu ISO 16120 veljajo tudi splošne tehnične zahteve za dostavo, opredeljene v ISO 404.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 16120-1:2011
01-oktober-2011
1DGRPHãþD
SIST EN 10016-1:1997
9URþHYDOMDQDåLFDL]QHOHJLUDQHJDMHNOD]DYOHþHQMHLQDOLKODGQRYDOMDQMHGHO
6SORãQH]DKWHYH ,62
Non-alloy steel wire rod for conversion to wire - Part 1: General requirements (ISO 16120
-1:2011)
Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 1: Allgemeine Anforderungen (ISO
16120-1:2011)
Fil-machine en acier non allié destiné à la fabrication de fils - Partie 1: Exigences
générales (ISO 16120-1:2011)
Ta slovenski standard je istoveten z: EN ISO 16120-1:2011
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
SIST EN ISO 16120-1:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 16120-1:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 16120-1:2011
EUROPEAN STANDARD
EN ISO 16120-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2011
ICS 77.140.60 Supersedes EN 10016-1:1994
English Version
Non-alloy steel wire rod for conversion to wire - Part 1: General
requirements (ISO 16120-1:2011)
Fil-machine en acier non allié destiné à la fabrication de fils Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 1:
- Partie 1: Exigences générales (ISO 16120-1:2011) Allgemeine Anforderungen (ISO 16120-1:2011)
This European Standard was approved by CEN on 30 June 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16120-1:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 16120-1:2011
EN ISO 16120-1:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 16120-1:2011
EN ISO 16120-1:2011 (E)
Foreword
This document (EN ISO 16120-1:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 106 “Wire rod and wires” the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withdrawn at
the latest by January 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10016-1:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 16120-1:2011 has been approved by CEN as a EN ISO 16120-1:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 16120-1:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 16120-1:2011
INTERNATIONAL ISO
STANDARD 16120-1
Second edition
2011-07-01
Non-alloy steel wire rod for conversion to
wire —
Part 1:
General requirements
Fil-machine en acier non allié destiné à la fabrication de fils —
Partie 1: Exigences générales
Reference number
ISO 16120-1:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 16120-1:2011
ISO 16120-1:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 16120-1:2011
ISO 16120-1:2011(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Classification .2
5 Ordering information to be supplied by the purchaser.3
6 Production process.4
7 Requirements.4
7.1 General .4
7.2 Quality system .4
7.3 Method of delivery.4
7.4 Delivery condition .4
8 Dimensions, mass and tolerances .4
9 Inspection.4
9.1 Inspection and inspection documents.4
9.2 Extension of inspection.5
9.3 Acceptance unit, number of samples and test pieces .5
9.4 Sampling and preparation of samples and test pieces .6
9.5 Test methods .6
9.6 Retest.7
10 Marking.7
11 Disputes.7
Annex A (normative) Determination of core segregation.8
Annex B (informative) Measurement of surface discontinuities.11
Annex C (informative) Mechanical damage.14
Annex D (normative) Determining the percentage of resolvable pearlite.19
Bibliography.21
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 16120-1:2011
ISO 16120-1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16120-1 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 17, Steel wire rod
and wire products.
This second edition cancels and replaces the first edition (ISO 16120-1:2001), which has been technically
revised.
ISO 16120 consists of the following parts, under the general title Non-alloy steel wire rod for conversion to
wire:
⎯ Part 1: General requirements
⎯ Part 2: Specific requirements for general-purpose wire rod
⎯ Part 3: Specific requirements for rimmed and rimmed substitute, low-carbon steel wire rod
⎯ Part 4: Specific requirements for wire rod for special applications
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 16120-1:2011
INTERNATIONAL STANDARD ISO 16120-1:2011(E)
Non-alloy steel wire rod for conversion to wire —
Part 1:
General requirements
1 Scope
1.1 ISO 16120 is applicable to wire rod of non-alloy steel intended for wire drawing and/or cold rolling. The
cross-section can be circular, oval, square, rectangular, hexagonal, octagonal, half-round or another shape,
generally with at least 5 mm nominal dimension, and with a smooth surface.
1.2 This part of ISO 16120 covers general requirements and is not applicable to products for which
standards exist or are in development, for example:
⎯ steel wire rod intended for heat treatment;
⎯ free-cutting steel wire rod;
⎯ steel wire rod for cold heading and cold extrusion;
⎯ steel wire rod intended for the production of electrodes and products for welding;
⎯ steel wire rod for welded fabric for reinforcement for concrete;
⎯ steel wire rod for ball and roller bearings (see ISO 683-17);
⎯ steel wire rod for wire for high fatigue strength mechanical springs, such as valve springs.
1.3 In addition to the requirements of this part of ISO 16120, the general technical delivery requirements
specified in ISO 404 apply.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 377, Steel and steel products — Location and preparation of samples and test pieces for mechanical
testing
ISO 404:1992, Steel and steel products — General technical delivery requirements
ISO 3887, Steels — Determination of depth of decarburization
ISO 4885, Ferrous products — Heat treatments — Vocabulary
ISO 4948-1, Steels — Classification — Part 1: Classification of steels into unalloyed and alloy steels based on
chemical composition
© ISO 2011 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 16120-1:2011
ISO 16120-1:2011(E)
ISO 4948-2, Steels — Classification — Part 2: Classification of unalloyed and alloy steels according to main
quality classes and main property or application characteristics
ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
ISO 6929, Steel products — Definitions and classification
ISO/TR 9769, Steel and iron — Review of available methods of analysis
ISO 10474, Steel and steel products — Inspection documents
ISO 14284, Steel and iron — Sampling and preparation of samples for the determination of chemical
composition
ISO 16120-2:2011, Non-alloy steel wire rod for conversion to wire — Part 2: Specific requirements for general-
purpose wire rod
ISO 16120-3:2011, Non-alloy steel wire rod for conversion to wire — Part 3: Specific requirements for rimmed
and rimmed substitute, low-carbon steel wire rod
ISO 16120-4:2011, Non-alloy steel wire rod for conversion to wire — Part 4: Specific requirements for wire rod
for special applications
ISO 16124, Steel wire rod — Dimensions and tolerances
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 377, ISO 404, ISO 4885,
ISO 4948-1, ISO 4948-2 and ISO 6929 and the following apply.
3.1
rod
hot-rolled finished product hot-wound into irregular coils
NOTE Rod used for wire-drawing purposes in coil form is generally termed wire rod.
3.2
heat analysis
chemical analysis representative of the heat, by a method determined at the steelmaker's discretion
NOTE Adapted from ISO 404:1992.
3.3
product analysis
chemical analysis carried out on a sample of the product taken after the final hot rolling operation
NOTE Adapted from ISO 404:1992.
3.4
resolvable pearlite
two-phased structure in which ferrite and iron carbide lamellae can be clearly observed under optical
microscopy in certain conditions
4 Classification
The classification of the steel grades covered by this part of ISO 16120 is indicated in ISO 16120-2,
ISO 16120-3 and ISO 16120-4 for the corresponding steel grades.
2 © ISO 2011 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 16120-1:2011
ISO 16120-1:2011(E)
5 Ordering information to be supplied by the purchaser
The following information shall be supplied by the purchaser at the time of enquiry and order, to enable the
supplier to comply satisfactorily with the requirements of ISO 16120:
a) quantity to be delivered;
b) cross-section and product type (round wire rod, square wire rod, hexagonal wire rod, etc.);
c) nominal dimensions of the wire rod and tolerance class in accordance with ISO 16124 (if another
tolerance class such as T1 is required);
d) reference to the relevant part of ISO 16120, i.e. ISO 16120-2;
e) steel grade, including any variations, and/or the addition of other elements, as permitted in ISO 16120-2
and ISO 16120-4; for steels according to ISO 16120-2 and ISO 16120-4, wire rod can also be ordered by
the mean tensile strength; see Clause 3 and 4.6 of ISO 16120-2:2011 and Clause 3 and 4.8 of
ISO 16120-4:2011;
f) the type of inspection and inspection document in accordance with ISO 10474 (or in accordance with
other regional standards, e.g. EN 10204, see the Bibliography);
g) surface condition (where different from the as-rolled condition);
h) dimensions and mass of coils;
i) where applicable, indication of the type of descaling (chemical cleaning or mechanical);
j) where applicable, the amount of microalloying elements (see ISO 16120-2 and ISO 16120-4);
k) where applicable, class B for the depth of decarburization (see ISO 16120-4); if nothing is mentioned in
the order, class A will be delivered;
l) where applicable, the microstructure (see ISO 16120-4:2011, 4.11);
m) where applicable, suitability for galvanizing;
n) where applicable, suitability for direct drawing;
o) where applicable, the quality system (see 7.2);
p) where applicable, the method of binding and labelling.
Items g) to p) are options. If the purchaser does not indicate a wish to implement any of these options, the
supplier shall supply the product in accordance with the basic specifications of Items a) to f).
The following are two ordering examples.
EXAMPLE 1 For grades ordered according to chemical composition, 100 tonnes of round wire rod, nominal diameter
of 12 mm with dimensional tolerances according to ISO 16124, class T1, steel grades ISO 16120-2 – C52D in the as-
rolled condition with an inspection document 3.1.B according to ISO 10474
100 t round wire rod ISO 16124-12,0T1
ISO 16120-2 – C52D
ISO 10474 inspection document 3.1.B
EXAMPLE 2 For grades ordered according to tensile strength, 200 tonnes of round wire rod, nominal diameter of
5,5 mm with dimensional tolerances according to ISO 16124, class T1, steel grades ISO 16120-4 – C##D2 with tensile
strength 1020 MPa in the as-rolled condition with an inspection document 3.1.B according to ISO 10474.
© ISO 2011 – All rights reserved 3
---------------------- Page: 13 ----------------------
SIST EN ISO 16120-1:2011
ISO 16120-1:2011(E)
200 t round wire rod ISO 16124-5,5T1
ISO 16120-4 – C##D2-1020
ISO 10474 inspection document 3.1.B
NOTE ## means “to be left blank” since the carbon content is at the discretion of the supplying mill, and the supplying
mill indicates the exact number of ## based on the grade designation until shipment. See Table 1 of ISO 16120-2:2011
and ISO 16120-4:2011, respectively, for the grade designation.
6 Production process
At the request of the purchaser at the time of enquiry and ordering, the steel making and manufacturing
process shall be made known to the purchaser. Those processes that are specifically agreed upon shall not
be changed without the prior agreement of the purchaser.
7 Requirements
7.1 General
Suppliers are responsible, using the means they think fit, for inspecting their product in accordance with
various quality criteria specified. In view of the practical difficulties in inspecting a coil of wire rod along its
entire length, it cannot be proved that no value greater than the specified limits is to be found in the coil as a
whole. Statistical evaluation of performances applicable to all coils may be agreed between the purchaser and
the manufacturer at the time of ordering.
7.2 Quality system
If agreed between the supplier and purchaser at the time of enquiry and order, the wire rod supplied shall be
produced under a mutually acceptable quality system.
7.3 Method of delivery
Wire rod shall be delivered by heat or part of a heat. Unless otherwise specified, the number of heats per
delivery should be minimized as far as possible.
7.4 Delivery condition
Wire rod shall be supplied in the as-rolled state, in coils of one continuous length with non-aligned turns, but
capable of being unwound in a regular manner during subsequent processing.
The coils shall be cut back at both ends to provide a product of uniform shape and properties.
8 Di
...
SLOVENSKI STANDARD
oSIST prEN ISO 16120-1:2010
01-februar-2010
9URþHYDOMDQDåLFDL]QHOHJLUDQHJDMHNOD]DYOHþHQMHLQDOLKODGQRYDOMDQMHGHO
6SORãQH]DKWHYH ,62',6
Non-alloy steel wire rod for conversion to wire - Part 1: General requirements (ISO/DIS
16120-1:2009)
Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 1: Allgemeine Anforderungen
(ISO/DIS 16120-1:2009)
Fil-machine en acier non allié destiné à la fabrication de fils - Partie 1: Exigences
générales (ISO/DIS 16120-1:2009)
Ta slovenski standard je istoveten z: prEN ISO 16120-1
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
oSIST prEN ISO 16120-1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 16120-1:2010
---------------------- Page: 2 ----------------------
oSIST prEN ISO 16120-1:2010
EUROPEAN STANDARD
DRAFT
prEN ISO 16120-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2009
ICS 77.140.60 Will supersede EN 10016-1:1994
English Version
Non-alloy steel wire rod for conversion to wire - Part 1: General
requirements (ISO/DIS 16120-1:2009)
Fil-machine en acier non allié destiné à la fabrication de fils Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 1:
- Partie 1: Exigences générales (ISO/DIS 16120-1:2009) Allgemeine Anforderungen (ISO/DIS 16120-1:2009)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
ECISS/TC 15.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 16120-1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 16120-1:2010
prEN ISO 16120-1:2009 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 16120-1:2010
prEN ISO 16120-1:2009 (E)
Foreword
This document (prEN ISO 16120-1:2009) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 15 “Wire-rod - Qualities, dimensions, tolerances and
specific tests” the secretariat of which is held by UNI.
This document is currently submitted to the parallel Enquiry.
This document will supersede EN 10016-1:1994.
Endorsement notice
The text of ISO/DIS 16120-1:2009 has been approved by CEN as a prEN ISO 16120-1:2009 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 16120-1:2010
---------------------- Page: 6 ----------------------
oSIST prEN ISO 16120-1:2010
DRAFT INTERNATIONAL STANDARD ISO/DIS 16120-1
ISO/TC 17/SC 17 Secretariat: SAC
Voting begins on: Voting terminates on:
2009-12-03 2010-05-03
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Non-alloy steel wire rod for conversion to wire —
Part 1:
General requirements
Fil-machine en acier non allié destiné à la fabrication de fils —
Partie 1: Exigences générales
[Revision of first edition (ISO 16120-1:2001)]
ICS 77.140.60
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2009
---------------------- Page: 7 ----------------------
oSIST prEN ISO 16120-1:2010
ISO/DIS 16120-1
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 16120-1:2010
ISO/DIS 16120-1
Contents Page
Forew ord . v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Classification .2
5 Ordering information to be supplied by the purchaser.3
6 Production process .4
7 Requirements.4
7.1 General .4
7.2 Quality system.4
7.3 Method of delivery.4
7.4 Delivery condition .4
8 Dimensions, mass and tolerances.4
9 Inspection .5
9.1 Inspection and inspection documents.5
9.2 Extension of inspection.5
9.3 Acceptance unit, number of samples and test pieces .5
9.4 Sampling and preparation of samples and test pieces.6
9.5 Test methods .6
9.6 Retest.7
10 Marking .7
11 Disputes.7
Annex A (normative) Determination of core segregation .8
A.1 Scope .8
A.2 Term and definition.8
A.3 Principle.8
A.4 Preparation of samples .8
A.4.1 Cutting .8
A.4.2 Polishing.8
© ISO 2002 – All rights reserved iii
DRAFT 2009
---------------------- Page: 9 ----------------------
oSIST prEN ISO 16120-1:2010
ISO/DIS 16120-1
A.4.3 Etching .9
A.4.4 Evaluation of the segregation.9
A.4.5 Classes of segregation.9
A.4.6 Evaluation of the test results.9
Annex B (informative) Measurement of surface discontinuities . 11
B.1 Introduction. 11
B.2 Term and Definition . 11
B.3 Principle. 11
B.4 Preparation of samples . 11
B.4.1 Cutting . 11
B.4.2 Polishing. 11
B.4.3 Etching. 11
B.4.4 Evaluation of the Depth of the surface discontinuity . 11
B.4.5 Reporting of Results . 12
Annex C (informative) Mechanical Damage. 14
C.1 Introduction. 14
C.2 Term and Definition . 14
C.3 Illustrations of mechanical damage and the consequences. 14
C.3.1 Types of damage and probable causes. 14
C.3.2 The consequences of mechanical damage. 15
C.4 Avoidance of mechanical damage . 17
Annex D (normative) Determination of Percentage of Resolvable Pearlite. 18
D.1 Scope . 18
D.2 Principle. 18
D.3 Preparation of samples . 18
D.3.1 Cutting . 18
D.3.2 Polishing. 18
D.3.3 Etching. 18
D.3.4 Evaluation of the Percentage of Resolvable Pearlite. 18
D.3.5 Reporting of Results . 19
iv © ISO 2002 – All rights reserved
DRAFT 2009
---------------------- Page: 10 ----------------------
oSIST prEN ISO 16120-1:2010
ISO/DIS 16120-1
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for
voting. Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 16120-1 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee
SC 17, Steel wire rod and wire products.
This first edition of ISO 16120-1, together with parts 2, 3 and 4 cancels and replaces ISO 8457-2:1989 which
has been technically revised and augmented.
ISO 16120 consists of the following parts, under the general title Non-alloy steel wire rods for conversion to
wire:
- Part 1: General requirements
- Part 2: Specific requirements for general purpose wire rod
- Part 3 Specific requirements for rimmed and rimmed substitute low carbon steel wire rod
- Part 4 Specific requirements for wire rod for special applications
Annexes “A” and “D” form a normative part of this part of ISO 16120. Annexes “B” and “C” are illustrative only
© ISO 2002 – All rights reserved v
DRAFT 2009
---------------------- Page: 11 ----------------------
oSIST prEN ISO 16120-1:2010
---------------------- Page: 12 ----------------------
oSIST prEN ISO 16120-1:2010
DRAFT INTERNATIONAL STANARD ISO/DIS 16120-1
Non-alloy steel wire rod for conversion to wire —
Part 1:
General requirements
1 Scope
1.1 ISO 16120 is applicable to wire rod of non-alloy steel intended for wire drawing and/or cold rolling. The
cross-section may be circular, oval, square, rectangular, hexagonal, octagonal, half-round or other shape and
generally with at least 5 mm nominal dimension, and a smooth surface.
1.2 It is not applicable to products for which standards exist or are under study, e.g.:
- steel wire rod intended for heat treatment;
- free-cutting steel wire rod ;
- steel wire rod for cold heading and cold extrusion;
- steel wire rod intended for the production of electrodes and products for welding;
- steel wire rod for welded fabric for reinforcement for concrete ;
- steel wire rod for ball and roller bearings (see ISO 683-17);
- steel wire rod for wire for high fatigue strength mechanical springs, such as valve springs.
1.3 In addition to the requirements of this part of ISO 16120 the general technical delivery requirements
specified in ISO 404 apply.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical
testing
ISO 404,Steel and steel products - General technical delivery requirements
ISO 3887, Steel, non-alloy and low-alloy - Determination of depth of decarburization
ISO 4885, Ferrous products - Heat treatments - Vocabulary
ISO 4948-1, Steels - Classification - Part 1: Classification of steels into unalloyed and alloyed steels based
on chemical composition
ISO 4948-2, Steels - Classification - Part 2: Classification of unalloyed and alloyed steels according to main
quality classes and main property or application characteristics
© ISO 2002 – All rights reserved 1
DRAFT 2009
---------------------- Page: 13 ----------------------
oSIST prEN ISO 16120-1:2010
ISO/DIS 16120-1
ISO 6892, Metallic materials - Tensile testing at ambient temperature
ISO 6929, Steel products - Definitions and classification
ISO/TR 9769, Steel and iron - Review of available methods of analysis
ISO 10474, Steel and steel products - Inspection documents
ISO 14284, Steel and iron - Sampling and preparation of samples for the determination of chemical
composition
ISO 16120-2, Non-alloy steel wire rods for conversion to wire - Part 2: Specific requirements for general
purpose wire rod
ISO 16120-3, Non-alloy steel wire rods for conversion to wire - Part 3: Specific requirements for rimmed and
rimmed substitute low carbon steel wire rod
ISO 16120-4, Non-alloy steel wire rods for conversion to wire - Part 4: Specific requirements for wire rod for
special applications
ISO 16124, Steel wire rod - Dimensions and tolerances
3 Terms and definitions
For the purpose of each part of ISO16120, the definitions given in ISO 377, ISO 404, ISO 4885, ISO 4948-1,
ISO 4948-2 and ISO 6929 and the following terms and definitions apply.
3.1
rod
hot-rolled finished product hot wound into irregular coils
Rod used for wire-drawing purposes in coil form is generally termed wire rod.
3.2
heat analysis
chemical analysis representative of the heat, by a method determined at the steelmaker’s discretion.
3.3
product analysis
chemical analysis carried out on a sample of the product taken after the final hot rolling operation.
3.4
resolvable Pearlite
is defined as pearlite where the ferrite and iron carbide lamellae can be clearly observed under optical
microscopy using the conditions identified in this annex.
4 Classification
The classification of the steel grades covered by this part of ISO 16120 are indicated in ISO 16120-2, ISO
16120-3 and ISO 16120-4 for the corresponding steel grades.
2 © ISO 2002 – All rights reserved
DRAFT 2009
---------------------- Page: 14 ----------------------
oSIST prEN ISO 16120-1:2010
ISO/DIS 16120-1
5 Ordering information to be supplied by the purchaser
The following information shall be supplied by the purchaser at the time of enquiry and order, to enable the
supplier to comply satisfactorily with the requirements of ISO 16120:
a) quantity to be delivered;
b) cross-section and product type (round wire rod, square wire rod, hexagonal wire rod etc.);
c) reference to the dimensional standard ISO 16124;
d) nominal dimensions of the wire rod and tolerance class according to ISO 16124 (if another tolerance class
as T1 is required);
e) reference to the relevant part of ISO 16120, i.e. ISO 16120-2;
f) steel grade, including any variations, and/or the addition of other elements, as permitted in ISO 16120-2 and
ISO 16120-4. For steels according to ISO 16120-2 and ISO 16120-4, wire rod can also be ordered by the
mean tensile strength. See clause 3 and 4.6 of ISO 16120-2 and clause 3 and 4.8 of ISO 16120-4;
g) the type of inspection and inspection document in accordance with ISO 10474 (or in accordance with other
regional standards: e.g.: EN 10204, see bibliography).;
h) surface condition (where different from the as-rolled condition);
i) dimensions and mass of coils;
j) where applicable, indication of the type of descaling (chemical cleaning or mechanical);
k) where applicable the amount of microalloying elements (see ISO16120-2 and ISO 16120-4);
l) where applicable, the class B for the depth of decarburization (see ISO 16120-4), if nothing is mentioned in
the order, class A will be delivered:
m) where applicable, the microstructure ( See ISO 16120-4, clause 4.11);
n) where applicable, if the steel grade shall be suitable for galvanizing;
o) where applicable, suitable for direct drawing;
p) where applicable, the quality system (see 7.2);
q) where applicable, the method of binding and labelling.
Points h) to q) are options. If the purchaser does not indicate a wish to implement any of these options, the
supplier shall supply in accordance with the basic specifications of points a) to g).
Two ordering examples
Example for grades ordered to chemical composition 100 tonnes of round wire rod, nominal diameter of 12 mm with
dimensional tolerances according to ISO 16124 class T1, steel grades ISO 16120-2 – C52D in the as-rolled condition with
an inspection document 3.1.B according to ISO 10474:
100t round wire rod ISO 16124-12,0T1
ISO 16120-2 – C52D
ISO 10474 inspection document 3.1.B
© ISO 2002 – All rights reserved 3
DRAFT 2009
---------------------- Page: 15 ----------------------
oSIST prEN ISO 16120-1:2010
ISO/DIS 16120-1
Example for grades ordered to tensile strength 200 t of round wire rod, nominal diameter of 5.5 mm with dimensional
tolerances according to ISO 16124 class T1, steel grades ISO 16120-4 – C##D2 with tensile strength 1020 MPa in the as
rolled condition with an inspection document 3.1.B according to ISO 10474:
200t round wire rod ISO 16124-5,5T1
ISO 16120-4 – C##D2-1020
ISO 10474 inspection document 3.1.B
NOTE ## means to be left blank since carbon content is at the discretion of the supplying mill, and supplying mill
informs the exact number of ## based on the grade designation until shipment. See Table 1 of ISO 16120-2 and 16120-4
respectively as for the grade designation.
6 Production process
At the request of the purchaser at the time of enquiry and ordering, the steel making and manufacturing
process shall be made known to the purchaser. Those processes that are specifically agreed shall not be
changed without prior agreement of the purchaser.
7 Requirements
7.1 General
Suppliers are responsible, using the means they think fit, for inspecting their product in accordance with
various quality criteria specified. In view of the practical difficulties in inspecting a coil of wire rod along its
entire length, it cannot be proved that no value greater than the specified limits is to be found in the coil as a
whole. Statistical evaluation of performances applicable to all coils may be agreed between the purchaser and
the manufacturer at the time of ordering.
7.2 Quality system
If agreed between supplier and purchaser at the time of enquiry and order, the wire rod supplied shall be
produced under a mutually acceptable quality system.
7.3 Method of delivery
The products shall be delivered by heat or part of a heat. Unless otherwise specified the number of heats per
delivery should be minimized as far as possible.
7.4 Delivery condition
Wire rod shall be supplied in the as-rolled state, in coils of one continuous length with non-aligned turns, but
capable of being unwound in a regular manner during subsequent processing.
The coils shall be cut back at both ends to provide a product of uniform shape and properties.
8 Dimensions, mass and tolerances
The dimensions, mass and tolerances of the products shall be in accordance with the requirements of ISO
16124
4 © ISO 2002 – All rights reserved
DRAFT 2009
---------------------- Page: 16 ----------------------
oSIST prEN ISO 16120-1:2010
ISO/DIS 16120-1
9 Inspection
9.1 Inspection and inspection documents
Inspection and inspection documents shall be in accordance with ISO 404 and ISO 10474.
9.2 Extension of inspection
If the order is accompanied by a request for an inspection certificate or an inspection report, the inspection
shall be carried out in accordance with Table 1. In the case that the order requires an inspection document
3.1C or 3.2 the purchaser shall supply to the manufacturer the name and address of the organization or
person nominated to c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.